Search Documents

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

By Charles L. Kimbell

In 1990, the aggregate value of world international export trade in mineral commodities was estimated at more than $64 billion in current (1990) dollars, about 8.4% higher than that in 1989, but still 8.7% below the record high set in 1980. Table 8 provides a data series for the estimated value of world export trade in all mineral commodities from 1979 through 1990, as well as a breakdown of this total into fuel and nonfuel commodities. It is noteworthy that for this 1990 edition, trade data for the year of review were available in time for inclusion, whereas in previous editions, the latest available global trade data were for the year prior to the year of review. Hence, as regards trade, this edition of Minerals in the World Economy updates the 1989 edition by 2 years rather than by only 1. For this reason, it is appropriate to note that the 1989 global total value for inter-national export trade in mineral commodities was almost $596 billion, 11.1 % above the revised 1988 level of more than $536 billion, both figures expressed in current dollars for the appropriate year. Despite the considerable increase in the dollar value of mineral commodity exports, their share of total export merchandise trade declined to 19.1 % in 1990 from 19.7% in 1989. At 19.1%, this share was very near the recent year record low of 19.0% reached in 1988. The year 1990 was the fourth in a row in which the total value of world mineral commodity export trade increased.

Jan 1, 1993

By Edward W. Parsons

The explosive-expansion center-hole anchor was designed and developed for the specific purpose of use as a component of an instrument system that measures differential ground movement within a small drill hole in rock. Such anchors should have an unobstructed center hole, should be installed without a twisting action which could tangle connecting wires, and should be capable of being installed at depths in excess of 100 feet. The anchor has a thick-walled center tube and a thin-walled outer tube. Low-energy detonating cord, wrapped around the center tube and detonated with a mild end primer, expands the outer tube to produce anchorage. The explosive-expansion center-hole anchor can be installed easily in drill holes of any inclination but cannot be installed under water. Centering of the anchor is critical with regard to its subsequent holding power. The anchor is safe to make and handle.

Jan 1, 1965

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection with this work, the petrographic laboratory is called

Jan 1, 1940

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection ,with this work, the petrographic laboratory is called

Jan 1, 1940

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973

By Alex C. Smith, Thomas P. Mucho, John B. Walsh, Alden Ozment, Michael R. Thibou, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), with US Foam Technologies, Inc. and On Site Gas Systems, Inc., conducted research on the remote application of extinguishing agents with the intent of improving deployment strategies to limit miner exposure and to help ensure the best possible outcome during a mine fire. Full-scale in-mine were conducted at the NIOSH Lake Lynn Experimental Mine to determine the flow characteristics, stability and fire-suppression capability of gas-enhanced foam. The in-mine experimental work was designed to evaluate movement of gas-enhanced foam through mine workings closely simulating an underground coal mine environment and how long gas-enhanced foam would remain stable. This paper presents results of the experiments and provides valuable insight into mine fire deployment strategies for gas-enhanced foam technology.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS.

Jan 1, 1977

By R. V. Ramani, A. S. C. Owili-eger

The quantity of methane emitted into the mine atmosphere and the movement of gas through solid coal and the adjoining country rock are dependent on the physical properties of the medium, boundary con¬ditions, the initial gas pressure distribution, and the combination of natural and mining factors. Functional relationships between these factors are not yet known. Consequently, the development of rigorous mathematical models to predict methane flow into the mine air is difficult and to date no model has been reported which is capable of such a function. Thus far, empirical formulas available for the calculation of gas quantity released from underground sources require too much his¬torical data, not currently available. Again, these estimations are at best only crudely approximate. The numerical methods available have not been made practical enough for industry wide application. Therefore, the development of a relationship amenable to numerical analysis and practical enough for use in the industry would provide the flexibility lacking in analytical approaches. The mathematical models given in equations (7) and (8) are further attempts in presenting practical models for predicting the quantity of methane emission into the mine environment. Equation (7) is the steady state model and equation (8) is the unsteady state model.

Jan 1, 1974

By Alan H. Goode

As part of the Bureau of Mines program to broaden utilization of abundant low-quality mineral materials, the Tuscaloosa Metallurgy Research Laboratory conducted beneficiation studies on two Alabama clays. The main purpose of these studies was to develop improved plasticity and green strength in both clays and compare these improved properties with those of a typical ball clay. Whiteness of the clays was also considered. The results indicated that by adjusting the pH of the kaolin to approximately 9, a substitute for ball clay could be obtained. The investigation also showed that by a combination of attrition grinding and sodium dithionite leaching to remove iron, the underclay could be upgraded to a ball clay material.

Jan 1, 1975

By Lloyd A. Morley, Robert Stefanko

This report has presented a literature review of explosion proof¬ing of coal mine electrical equipment. The international "state-of¬the-art" is an extremely difficult definition to quantify but, from the preceding paragraphs, it is evident the international community be¬lieves that it is represented by the International Electrotechnical Commission's Publications. Five questions were set forth during the beginning of this report. Each will be evaluated in light of the preceding discussion. 1. Can Schedule 2G specifications on explosion-proof containers be substantiated? Literature was found in the three main problem areas, surface temperature, mechanical strength, and explosion transmission, to determine this. Surface temperature requirements are adequate except for equipment that can normally overload, and the required intern¬al pressure does afford some margin of safety. However, in terms of safety, gap dimensions are about ten times smaller than that needed. 2. Is it possible to replace the Schedule's design requirements with performance specifications? Two primary areas were determined as mechanical strength and explosion transmission. As was mentioned, for present flange and gap standards, the 150 psig requirement is adequate. Furthermore, it is the authors' opinion that the level cannot be re¬duced if the present gap requirements are retained. The Schedule now requires that 16 tests be run, but the literature suggests that only from three to six examinations are necessary. Then by using the abso¬lute maximum pressure from these measurements or 150 psig, whichever is

Jan 1, 1974

The optimum situation in sealing the soil with latex would be to locate the sealant at the depth where natural permeability is lowest, and to narrow distribution of the latex to a film. To ascertain how closely we were achieving these objectives it was necessary to devise a method to measure the concentration of latex in soil. A number of methods were explored and two were used in actual field tests. SBR latex tagged with c14 was prepared and used to determine the distribution of polymer in the soil. The latex was made by copolymerizing a mixture of radioactive and normal styrene with butadiene in bottles by conventional methods. Average particle size was 600 Å. Diluted aliquots had 1.40 microcuries radioactivity per gram of latex. Tagged latex was mixed with soil in a range of proportions from 0.01 to 0.25% by weight to develop a calibration curve. Analyses of soil in the laboratory and from the field were determined by comparison with this master curve. Styrene-containing polymers have a characteristic peak at 700 cm-1 but crosslinked SBR is not soluble in solvents normally used in infra-red spectroscopy, e.g., carbon disulfide. We developed a method for solubilizing the crosslinked polymer by stirring overnight at room temperature a soil sample in chloroform with t-butyl hydroperoxide and osmium tetroxide. The filtered chloroform residue was dried to constant weight, thoroughly mixed and pressed into a KBr pellet, and concentration was determined by measuring the absorption at 700 cm-1. Details are given in an Appendix.

Jan 1, 1972

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. Gilsonite, a solidified hydrocarbon, found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), by Ziegler Chemical and Mineral Corp., and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT.

Jan 1, 1984

By J. O. Winget

Amino acids were investigated in conjunction with rare-earth separation by ion exchange to determine whether they can be utilized effectively as retaining agents for metals separation using ethylenediaminetetraacetic acid (EDTA) eluant at 85° to 90° C. Hydroxyethylethylenediaminetriacetic acid (REDTA) and diethylenetriamine pentaacetic acid (DTPA) were the most effective amino acids investigated. Elements of atomic numbers 39 and 57 through 68 were effectively retained, whereas elements of atomic numbers 69 through 71 passed through the retaining-agent band. Utilization of REDTA or DTPA retaining agents allows an increase of 75 percent in the EDTA eluant concentration over that possible with hydrogen-or copper-retaining ions without precipitation occurring. Eighty-five percent recovery of the EDTA eluant collected before rare-earth breakthrough and during elution of lutetium, ytterbium, and thulium, and essentially complete recovery of the REDTA or DTPA retaining agents, are possible without extensive processing.

Jan 1, 1968

By John C. Edwards, Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975

By J. A. Eisele

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has studied the removal of iron from simulated aluminum nitrate leach liquors by solvent extraction. Iron must be removed from aluminum nitrate liquor produced by leaching calcined kaolinitic clay with HN03 to reduce the iron level in alumina to less than 0.02 wt-pct Fe203 for use in reduction cells. The parameters reported are for (1) extracting iron from a feed containing 1.5 g/l Fe with di(2-ethylhexyl) phosphoric acid (EHPA), (2) stripping loaded organic phase with 20-pct HCI, and (3) water washing of loaded and stripped organic phase. Recommended operating conditions are two extraction stages using 15 vol-pct EHPA in kerosene and three stripping stages using 20-pct HCI. Results are also given for tests using other extractants and stripping agents.

Jan 1, 1982

By M. Gottlieb, P. Metes, Charles Sabine, Louis J. Denes, B. Kaminsky, Jami M. Girard, Ronald T. Mayerle

A significant risk factor in assessing and modeling potential catastrophic slope movement in open-pit mines is the presence of argillic alteration in host rocks. High-resolution hyperspectral imagery operating in the visible to shortwave infrared can be a useful tool for identifying and mapping potentially dangerous argillic zones. We have conducted preliminary experiments with a new type of hyperspectral imager that employs an acousto-optic tunable filter, a variable retardation plate and a standard digital camera. The instrument we tested operates in the .5-1.0 micrometer range. A shortwave infrared instrument is planned, and mid-infrared instruments have been designed. An AOTF consists of an acoustic transducer that generates an acoustic wave that propagates through an attached crystalline substance. The wave sinusoidally modulates the refractive index of the crystal, selectively diffracting incident light according to its wavelength. The instrument also measures polarization signatures of reflecting surfaces as well as their spectral properties, opening up new areas of possible research. Images can be acquired and processed at 30 frames/second. The AOTF camera system offers numerous advantages to geologists. It can be used as an airborne imager or as a portable field device to image pit walls, outcrops, rock specimens or drill core. It can be adapted to image polished sections under a microscope, and it could be used in underground workings. Algorithms can produce processed images in real time (e.g., ratio images), and, because it is a camera system, aerial images can be orthorectified.

By G. W. Murrie, W. P. Diamond, C. M. McCulloch

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over- burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976