Search Documents

By T. E. Gray

This report describes the preparation characteristics of the more significant coal beds in Allegheny County, Pa. It is one of a series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. More than 7 million tons of coal was produced in Allegheny County in 1957. Of this, more than 5 million tons was cleaned mechanically in nine cleaning plants. The Bureau of Mines estimated that, as of January 1, 1953, more than 384 million tons of recoverable coal remained in the county in beds 28 inches or thicker.

Jan 1, 1959

By L. W. Brandt

Studies of liquid-vapor equilibria of gas mixtures at the Bureau of Mines Amarillo Helium Plant Laboratory require that the equilibrium cell be maintained uniformly at any desired temperature from approximately room temperature to -320° F. The temperature-control system must also tolerate a substantial heat input, in the form of warm gas flowing into the cell, without loss of control. Temperatures between the sublimation temperature of carbon dioxide (-109° F.) and the boiling point of liquid nitrogen (320° F.) are usually obtained by methods utilizing a hydrocarbon liquid bath cooled by liquid nitrogen.4/5/6/7/ Owing to the fire hazard attending such baths, a safer method of temperature control was desirable.

Jan 1, 1955

By J. M. Oestreich

Supercritical water (sew) Is being tested for commercial use 1n several organic extraction systems but little work has been done on the extraction of metals from minerals. This lack of information prompted Bureau of Hines (BOM) research into the sew treatment of minerals. As a result, this research project is intended to serve mainly as a starting point for further experimentation. A simple flow-through reactor was built out of high pressure tubing and used to treat minerals with SCU at 400? C and 3500 to 7000 psi. The research produced four main conclusions: (1) carbonates of copper, iron, and lead convert to oxides; (2) most iron minerals showed alteration to oxides with some iron dissolution; (3) valuable trace elements including nickel, chromium, and others leached to some extent from sea minerals along with some calcium, iron, silicon, and sulfur; and (4) treatment of sulfides extracted elemental sulfur and resulted in several alteration reactions, though with the exception of cinnabar and the iron bearing minerals, the metals in sulfides were mainly insoluble. Surface alterations on many of the minerals show significant changes have occurred in the minerals even when only minor extractions were detected. These surface effects may be very important when used in conjunction with flotation processes since the sew treatment may selectively enhance or suppress a mineral's floatability.

Jan 1, 1989

By Donald N. H. Chi

The unsteady, one-dimensional, compressible-flow equations have been solved numerically for a deflagration propagating through a gallery of finite length closed at the ignition end and open at the opposite end. These equations were solved for two situations wherein (1) the propagating flame was extinguished after 0.1 sec or before the return of aerodynamic disturbances reflected from the open end, and (2) the flame was allowed to propagate a full 0.8 sec until it was extinguished. It was found that the process of sudden flame extinguishment creates rarefaction waves that, upon entering the burned zone, produce resonance within the burned cavity. For the relatively small value of the product of the expansion ratio (8.5) and the effective burning velocities of 7.4 m sec-1 for the first experiment and 4.9 m sec-1 for the second experiment, it was found that the acoustic approximation provides an adequate estimate of the pressures developed ahead of the flame during the system's early history.

Jan 1, 1974

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By C. E. Schmidt

Condensate waters from the Bureau of Mines Synthane process for coal gasification have been investigated by mass spectrometric methods to determine the organic contaminants. Waters from the gasification of six coals were extracted with methylene chloride, yielding 0.6 to 2.4 weight-percent extractable material. Using high-resolution mass spectrometry (HRMS), combined gas chromatography-mass spectrometry (GC-MS), and low-voltage mass spectrometry, 60 to 80 percent of the extract was found to be phenolic. About 20 organic contaminants have been identified and are present in the condensate waters from each coal gasified. The relative distribution of contaminants in the condensate water was nearly the same for the six coals gasified under various conditions; phenolic compounds were the most abundant in all cases.

Jan 1, 1974

By Franklin D. Cooper

This chapter includes tables for 1979 that were not available in time for publication in the 1978-79 Minerals Yearbook, but it does not include corresponding tables for 1980. The value of raw nonfuel mineral output in 1980 was estimated at $24.8 billion, 8.5% above the 1979 value. Of the 21 metal commodities produced, quantitative output increased for 11 and decreased for 10. The values for 10 metals were up, 10 were down, and 1 was unchanged. Among the 47 non-metallic commodities produced, 14 showed quantitative increases, 32 declined, and 1 was unchanged. In terms of value, 32 nonmetallics increased, and 15 declined.

Jan 1, 1981

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979

By Rudolf Kudlich

"During the coming winter, it is probable that many householders who have habitually been users of anthracite coal will be obliged to turn to some other fuel for heating purposes, because of the limited supply of anthracite. The next best fuel, from a standpoint of cleanliness and ease of operation, is coke, but here again the supply is inadequate and the householder will have to fall back on bituminous coal. Though bituminous coal has the dis¬advantage of being dirty to handle, requiring more care in firing, and of giving off considerable smoke, it will be more generally available, costs less, and in the better grades which will naturally find their way to the domestic market, is higher in heat value, and contains less ash than anthracite.Choice of CoalThere a variety of bituminous coals are available, the householder should choose a low volatile coal, such as New River, Pocahontas, or some other ""smokeless"" coal, or the British coal now being offered in the markets along the Atlantic seaboard. Though not necessary to have the coal sized, as is the case with anthracite, it will be found cleaner to use coal from which the fine dirt has been screened. If it is found that excessive dust is caused when firing the coal, this can be reduced by slightly wetting the coal at the front of the bin, as it is being used.Method of Firingusing bituminous coal instead of anthracite in the domestic furnace, it will be necessary to use an entirely different method of fir Instead of leveling the fuel bed and putting on fresh coal in an even layer over the entire fire box, the coked and partly burned coal remaining from the previous firing should be pushed as much as possible to one side of the box, and the fresh coal thrown into the empty side so as to leave some burning coal exposed. In this way the green coal is heated slowly, the volatile gases are given off gradually, and are ignited by the burninggoing to waste up the chimney unburned."

Oct 1, 1922

By E. Chin

Natural gas was the only economically significant mineral produced. A significant amount of the gas output was consumed in the production of nitrogen fertilizer and electric power. Proved reserves of natural gas were abundant and at least sufficient to supply most of the country's industrial and domestic needs for many decades to come. Other mineral production was of little importance to the Bangladesh economy, although there were prospects for developing some of the nonmetallic minerals. The flat river-delta terrain comprising nearly all of Bangladesh made the potential for discovering major, economically exploitable mineral deposits poor. The deep sediments, however, have good potential for crude oil or additional natural gas discoveries.

Jan 1, 1985

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health conducted a study of the explosibility of various metals and other elemental dusts dispersed in air, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating the explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafhium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties - from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" (very low volatility) elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechc ignitors. The experimental data obtained included the minimum explosible concentrations, maximum explosion pressures, and maximum explosion temperatures. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from -1 550 K for tin and tungsten powders to -2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures. In general, the dusts whose experimental temperatures were closer to the adiabatic values were those with the finer particle sizes, those that were more easily vaporized, and/or those that were intrinsically more reactive.

By T. E. Sterner

A laboratory investigation was conducted to determine the applicability of the thermal oil-recovery method as a means of increasing ultimate oil recovery in the Appalachian region. The primary objective was to establish self-sustained combustion in consolidated and unconsolidated sand test assemblies saturated with various amounts of Pennsylvania Grade crude oil and synthetic brine. Tests using blocks of sandstone were unsuccessful because of sealing problems and fracturing of the rock due to thermal stresses. A combustion wave of about 700° F was propagated through the sand-oil-water packs in the linear tube tests. The high air flux used resulted in high oil consumption and rapid movement of the combustion wave through the tubes. Analytical tests on the sand pack showed that sufficient fuel was deposited during the linear tube experiments for a self-sustained combustion wave.

Jan 1, 1967

By J. S. Browning

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from potash companies operating in the Permian basin near Carlsbad, N. Mex. These ores, containing 14 to 19 percent K20 and 3 to 5 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high clay content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions for clay disaggregation and removal as opposed to strenuous attritioning. Bench-scale beneficiation techniques for recovering potash minerals by flotation from the scrubbed material resulted in acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 59.6 to 60.4 percent K.0 values can be obtained. Continuous pilot plant beneficiation techniques for recovering potash minerals by flotation resulted in concentrates containing 58.8 to 59.8 percent K20 with recoveries of 69.7 to 81.4 percent of the K20.

Jan 1, 1975

The head loss data for coal slurries over a range of concentrations and velocities and the laboratory screen analysis were selected as areas for investigation in the data analysis performed. The analysis resulted in the following: (1) Size distributions for the coal used in the horizontal pipeline tests were fitted to the Rosin - Rammler distribution function. Each of the fits was significant. Corresponding Rosin - Rammler parameters were obtained which were introduced into the regression analysis. (2) A regression equation was obtained which predicts the slurry head loss of 1-inch by 0 coal slurries ranging in volumetric concentration from 20 to 40 percent and line velocities from 1 to 14 feet per second as a function of the square of velocity. The addition of the term for concentration in the regression equation did not contribute significantly c head loss.

Jan 1, 1972

By D. R. Tesarik

An instrumentation and numeric modeling study was conducted by the Bureau of Mines at the Magmont Mine in Bixby, MO. An isolated section of this room-and-pillar mine was monitored with borehole and closure extensometers during a pillar recovery program to determine stress redistribution. In situ stress measurements were taken in the rib before pillar extraction began. Sample cores from the boreholes were taken for analysis of the properties of the host rock in the laboratory. The extensometers recorded no measurable displacements during most of the operation. Two-dimensional, finite-element; three-dimensional, finite-element; and three-dimensional displace-ment discontinuity codes were used to model the area of study. The finite-element models were run with two initial stress conditions, i.e., stress due to gravity only and stress obtained by in situ measurements. Horizontal stresses in the models reduced the calculated factor-of-safety in the mine back by up to a factor of 10, but did not have a significant effect on calculated pillar stability.

Jan 1, 1989

By Árpád B. Palotás, Adel F. Sarofim, John B. Vander Sande, Paolo Ciambelli, Lenore Rainey

"The evolution during oxidation of the internal structure of soot and carbon black particles was studied using high-resolution transmission electron microscopy (HRTEM) and an image analysis system. Increasing ordering to the carbon structure with increasing oxidation is observed. Measures of the increased order are increases in the fractional coverage of a cross section of the particles with a layered structure, a decrease in the mean interlayer spacing, and a decrease in the spread of the interlayer spacing. The changing structure of the carbon black impacts its properties, such as the rate of oxidation.There is considerable interest in the study of the structural changes of carbonaceous materials as a function of oxidation. Davis et al.1 measured the variation of carbon dioxide surface area of various coals as a function of residence time in a flow reactor. HRTEM measurements revealed that crystallite dimensions and interlayer spacings are altered by combustion. Ishiguro et al.2 showed that oxidation alters the structure of diesel soot. The aim of our current research is to develop a better understanding of the microstructural reordering of carbon blacks with implications to their properties. The carbon blacks used in this research have already been studied and their reactivities as a function of oxidation measured.3The methodology used in this work has already been described in detail elsewhere.4 This paper presents an application to quantify the structural changes of carbon black particles as a function of oxidation and graphitization. The technique used is based on the use of HRTEM (high-resolution transmission electron microscopy) and computational image analysis.It is well-known that carbonaceous materials like graphite, soots, coals, chars, etc., possess characteristic structural appearances which can vary from mostly random or amorphous to a perfectly ordered graphitic crystalline structure. The carbon structure has been variously described as turbostratic5 or as crumpled sheets6 to indicate that parallel layering, reminiscent of graphite, is observed over dimensions of nanometers but that these planes or crystallites show disorder over larger scales. The degree of order of such structures is strongly dependent on the thermal treatment of the material as well as the composition of the source of the carbonaceous material. The value of electron micros¬copy in studying the morphology of such materials has been well established,2,7,8 although only a few attempts toward quantification have been made.The sample observed was carbon black CB330 from De¬gussa. One set of carbon black samples were oxidized in a thermo-gravimetric analyzer (TGA) in air at 575 0C, so that the conversion varied from 0 to 96%. Another set of carbon black samples were graphitized (Graphpac-GB by ALLTECH) and then oxidized in the TGA at 680 °C until 92% burnout was reached. The latter samples are called GB 0% and GB 92%, respectively.For the HRTEM observation a small portion of each sample was ultrasonically dispersed in ethanol. The suspension was deposited dropwise on a copper TEM grid coated with a lacey carbon film. The examination of the samples was carried out on areas that extend over the holes in the supporting film in order to avoid interference from the amorphous carbon background film An oriented gold crystal was used as a calibration standard and subjected to the same techniques as the carbon black samples."

Jan 1, 1998

By Edward J. Kansa

In a Bureau of Mines study, unsteady, spherically symmetric, one-dimensional, compressible-flow (finite sound speed) equations were solved numerically for a spherical deflagration propagating concentrically in a spherical vessel with Mach numbers ranging from 0.2 to 0.7; trajectory histories agree with the infinite-sound-speed theory developed by Perlee, Fuller, and Saul (PFS). A preliminary result of this study shows that flames propagating with speeds greater than 20 pct the speed of sound in the unburned gas mixture generate a complex history of aerodynamic waves distributed throughout the spherical vessel. Although the average pressure and flame radius agree with those predicted by the PFS models, the aerodynamic waves have a pronounced effect on the flame velocity, differing appreciably from that predicted by the PFS model.

Jan 1, 1976

By R. O. Kneisley

Rock mechanics measurements indicate that the present two-bed mine design used at the Big Island trona mine, Green River, Wyo., results in stable workings. Vertical pressure changes in the lower panel pillars and horizontal pressure changes in the lower bed roof and floor indicated negligible upper bed mining influence. Pillar stresses stabilized soon after upper bed mining was completed. Strata movements in the pillar ribs, roof, and floor were also negligible and stabilized soon after completion of upper bed mining. Using tributary area theory, the confined core approach, and studies of model trona pillars it is shown that increased extraction ratio is possible. A program of gradually increased extraction ratio accompanied by simple measurements should result in a mine design that includes both higher recovery and long-term stability.

Jan 1, 1981

By John A. Organiscak

The Bureau of Mines has recently completed a program to identify and evaluate various methods that address control of dust generated outby the longwall mining face. Dust generated by the stageloader-crusher, the panel belt, and the intake roadway can be long-term throughout the shift, contributing significantly to the dust exposure of all face workers. Dust control techniques were identified and tested at a number of longwall mining sections located in diverse geological conditions across the United States, Dust controls investigated include (1) methods that eliminate the sources of intake dust contamination--homotropal ventilation; (2) methods to limit the amount of respirable dust released into the intake airstream--improved water application and the use of curtains and enclosures; and (3) methods to clean the contaminated air prior to delivery to the mining face--scrubber systems. Usually they can be implemented at a low cost and can be very effective. This report describes each technique and its application and presents the resulting conclusions.

Jan 1, 1986

By W. N. Marchant

The Bureau of Mines improved removal of selenium from zinc smelter acidic gas scrubber effluent by using zinc dust to precipitate soluble selenium prior to lime neutralization. Lime neutralization alone decreased selenium in the waste water from, typically, 6 parts per million to 2 parts per million, whereas the use of zinc dust precipitant gave an effluent containing less than 0.1 part per million of selenium. The waste treatment operation first was developed on a laboratory scale and later was successfully tested at a smelter site on a 1-gallon-per-minute basis. During the research a simple and rapid means was developed for determining selenium in waste water; the technique enabled visual semiquantitative selenium determinations that later were confirmed quantitatively by X-ray fluorescence.

Jan 1, 1978