Search Documents

By John J. Sammarco, Janet S. Flynt

This report (Independent Functional Safety Assessment Guidance 7.0) is the last in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and after-market suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By I. AITKENS

The opal , long in disfavor because it was considered " unlucky, " has become much more popular in recent years . For variety and beauty of color the precious opal is without a peer . These colors do not come from any chemical constituent but are produced by structural peculiarities , which in varying degrees deflect the light rays entering the stone and give a prismatic play of hues .

Sep 1, 1931

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

By H. B. Humphrey, F. E. Cash

From 1900 to 1929 , 1,005 or approximately 30 per cent of all fatalities in the coal mines of Alabama were caused by fires or explosions of gas and dust . In the 3 -year period from 1927 to 1929 only 15 men were killed by these causes , a reduction from 30 to 9 per cent of the total . Notwithstanding this marked improvement , which is due largely to the efforts made by the State inspection department , the operators , and the Bureau of Mines to stamp out this type of disaster , Alabama still has more than its share of such fatalities which can and should be prevented. A list of explosions from 1894 to 1929 compiled from information obtained through the records of the State Inspector's office , the reports of Engineers of the Bureau of Mines , and the operators , is given in Table

Oct 1, 1930

By Launa Mallett, Charles Vaught, Michael Brnich, ROBERT PETERS

Interviews of 48 miners who escaped underground coal mine fires revealed that none of them had ever, before that incident, worn their self-contained self-rescuer (SCSR) either in training or in a real emergency. Consequently, they were ill-prepared to use this emergency breathing apparatus. One persistent problem stemmed from the fact that miners had no notion of breathing resistance, nor of the fact that it would get more difficult to breathe the longer they wore their device. As a result, many of those who were interviewed had simply removed their mouthpieces and breathed ambient air. This is obviously behavior that should be trained out of the workforce. Unfortunately, because of high costs and difficult logistics, miner training is unlikely to ever include donning and wearing an apparatus on a regular basis. In order to give workers a better idea of what to expect from their devices, therefore, the National Institute for Occupational Safety and Health researchers developed a tabletop (paper and pencil) simulation based upon actual predicaments evacuees had reported encountering. The simulation is designed to emphasize important points related to donning and wearing a self-contained self-rescuer in a mine fire escape, and, by doing so, to bring miners&apos; expectations more in line with what their actual experiences would be. The simulation was field tested in six training classes at three different mining operations. In all, 99 individuals were involved in completing the exercise and rating its properties. In their ratings 88% of the respondents indicated they thought the scenario could definitely happen in real life, and over 80% agreed they had learned something new. From the field test data it was concluded that the simulation had authenticity and potential value as a teaching tool. The simulation was therefore used in a pre-test/post-test control group experiment to determine whether it led to improvements in miners&apos; scores on a true-false test of their SCSR&apos;s functional capabilities and proper usage. Eighty-three miners were included in this part of the study. As expected, miners who had participated in the training exercise scored significantly higher on their post-test than miners who had not.

By Harry E. Tuff

"This paper is based data obtained by the Bureau of Mines from some of the principal mine operators in Pennsylvania, in the course of a study conducted in cooperation with the U. S. Forest Service, with regard to economies that might be effected in the selection storage, and preparations of timber particularly treatment with preservative to prolong its life.The Pennsylvania anthracite region, considered as a single mining district is by far the largest user of mine timber of any mining district, either coal or metal, in the United States, and the bituminous districts of Pennsylvania rank second. The present annual consumption of mine timber by the coal-mining industry of Pennsylvania probably exceeds 100,000,000 cubic feet annually.In 1919, Pennsylvania produced, in round figures, 145,300,000 tons of bituminous coal, 86,200,000 tons of anthracite, and 5,400,000 tons of iron ores. If it be assumed that the bituminous coal mines required 0.33 cubic feet, anthracite mines 0.7, and iron mines 0.9 cubic feet per ton mined the timber requirements were bituminous. 47,950,000; anthracite, 60,340,000; iron mines, 4,860,000 or a total of over 113,000,000 cubic feet.The average cost of round mine timber in the anthracite region in 1905, was, according to the U. S. Forest Service, 6.6 cents per cubic foot, and $15.00 per 1000 board feet for sawed timber. The present cost Las advanced to 27.5 cents per cubic foot for round timber, delivered to the mine, of which cost 57.4, represents freight charges."

Nov 1, 1923

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

Control the release of ground-water into active underground coal workings by short-term pumping from dewatering wells sited on fractures. Approach The sudden release of fracture-stored groundwater into underground coal workings often occurs when mine workings are developed beneath fracture valleys, Pumping from fracture trace-sited dewatering wells, prior to development of the underlying workings, can be an efficient means of intercepting fracture-stored groundwater before it is released into the mine. Dewatering operations are discontinued once the underlying mine workings have been fully developed, and the maximum possible reduction in fracture storage has been achieved through pumping. How It Works An aerial photographic technique known as fracture trace analysis is used to site dewatering wells on rock fractures in a valley bottom. Downhole caliper and temperature logs are used to assess the fracture flow potential of each dewatering well drilled.

Jan 1, 1987

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University&apos;s San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

By John Nagy, Henry G. Dorsett, Murray Jacobson

Laboratory studies show that ignition of a dispersed combustible dust in an open vessel may be prevented by adequate inerting . Factors affecting the inerting requirements are -- dust concentration , spark energy , ignition temperature , composition of the substances used for inerting , fineness of dust and type of combustible . The oxygen concentration of the atmosphere and in some instances the proportion of admixed inert powder and moisture required to prevent ignition are given for 367 dust samples . Variations in inerting requirements with strength of igniting source are discussed .

Jan 1, 1964

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are established it can be ascertained with a,of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town, whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well under drained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive."

Jun 1, 1921

By John Gross

The Alaska Station of the Bureau of Mines has recently conducted tests on two tailings from black sand which had been treated previously at the Station. The results of this previous treatment have be on given in a paper entitled "Recovery of Gold from Black Sand by Classifier Concentration." The gold in these tailings was intimately united with quartz, and was so finely divided that it could not be detected with the naked eye, nor even by P&nn ing unless the material was ground. Its fineness is further shown by the assºy result, which reported only lz per cent of the gold content as "metallics", Wºorea's the assay of the original sand reported 36 per cent of the gold as "metallics." The fact that the gold was in such fine particles, closely united with quartz, precluded further recovery by amalgamation without grinding. On the other hand, the small content present, as well as the lack of grinding appliances at the placer mines of Alasia, made it necessary that the material be cheaply handled if at all. With these facts in mind the experiments described below were undertake.n.

Oct 1, 1920

By R. B. Moore

The story of helium is one of the romances of science . Probably nothing , except perhaps radium , compares with it in human interest . Helium is one of the best examples of a discovery in pure science that has wide commercial application . In 1868 , an eclipse of the sun was visible in India , several scientific men who were in India making observations of the eclipse turned a spectroscope for the first time on the solar chromosphere - that part of the atmosphere of the sun , about 10,000 miles deep , which merges into the corona . A bright yellow line was observed and was thought at first to be due to sodium . Janssen showed , however , that this line was not just the same as either the D or D₂ line of sodium, although it was extremely close to these lines , hence he suggested that the new line have the designation D₂ . Frankland and Lockyer decided that Dz was due to an element in the sun not previously discovered on the earth , and suggested for it the name "Helium" from the Greek work " Helios " the sun . For several years nothing more was done in connection with this element . In 1894 , Sir William Ransay , in conjunction with Lord Rayleigh , made his memorable discovery of argon in the atmosphere , which was announced at the British Association meeting in the same year . After this discovery , Ramsay looked for other sources of the element . Through Sir Henry Miers , he learned that Dr. W. F. Hillebrand , of the United States Geological Survey , had obtained an inert gas from certain uranium minerals , which gas he had decided was nitrogen . Ramsay believed that part of it might be argon ; he obtained from Hillebrand for experimentation , a sample of the mineral , cleveite , one of the uranium minerals , and after extracting gas from the mineral and purifying it , he ran it into a spectrum tube . The lines obtained ' were , however , different from those of argon; among them was the bright yellow line noted by Janssen . Thus was terrestrial heliun discovered .

Jun 1, 1922

By Eric E. Cather

A mineral investigation by the U.S. Bureau of Mines revealed no mines or prospects and no past or present mining claims in the Agua Tibia Wilderness Study Area (WSA). The area is underlain mainly by weakly foliated gabbro similar to rock that has hosted gem- and lithium-bearing pegmatites in the Pala district about 6 mi to the south. However, no gem- or lithium-bearing pegmatites have been discovered in the WSA. Nearby quarries in the gabbro have yielded rock for facing and dimension stone. No sand, gravel, or energy (oil, gas, coal, or geothermal) resources were identified.

Jan 1, 1984

By B. D. Hanson

The U.S. Bureau of Mines has developed an interactive computer program which enables the user to identify the effect of cutting system changes on relative dust generation and forces for continuous miner drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. One or more of these parameters may be changed to determine their individual or collective effect on relative dust generation and cutting forces. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs.

Jan 1, 1989

By Clark R. Neuharth

To assess the supply status of ultra-high-purity silicon for national defense needs, the U.S. Bureau of Mines conducted a general study of the availability of materials and processing technology for silicon used in the manufacture of infrared (IR) detectors from raw materials to the highly advanced device state. The United States possesses all of the raw materials and processing technology for IR detector-grade silicon production, but does not produce at all of the processing stages on a regular basis. Consequently, the United States continues to rely on foreign sources for some of these critical materials.

Jan 1, 1989

By Daniel Edelstein

In 1985, ASARCO Incorporated terminated copper smelting operations and associated byproduct arsenic trioxide recovery at Tacoma, WA, although shipments of arsenic trioxide from stocks and limited production from cleanup operations continued. Imports of arsenic trioxide increased markedly as a result of increased demand for arsenical wood preservatives and the decline in domestic shipments of trioxide. Expanded world capacity more than met the increased demand for arsenic and its compounds, and prices remained unchanged throughout the year. Domestic Data Coverage.-Arsenic trioxide was produced by one U.S. company, which voluntarily reported its production to the Bureau of Mines.

Jan 1, 1987

A significant amount of information regarding the crushed stone and sand and gravel industries in each State is available from State agencies and State trade associations. These organizations continuously monitor the State mineral industries and are therefore an important source of detailed information at the local level. This third edition of the directory was prepared to provide a listing of government agencies and trade associations that can assist the users interested in obtaining detailed listings of crushed stone and sand and gravel producers, in addition to the information published by the U.S. Bureau of Mines.

Jan 1, 1994

By Russell J. Foster

This Bureau of Mines review focuses on the extent to which technologically and economically feasible programs in substitution, improved processing practices, including recycling, and design can achieve conservation of cobalt, chromium, manganese, and platinum-group metals, and thus reduce U.S. vulnerability to interruptions of supply. In addition, supply-side options--domestic and foreign resources, ocean minerals, and stockpiles--are identified. The report consolidates four major studies on these strategic and critical minerals sponsored entirely or partially by the Bureau in the last few years. These studies have been updated with further information from the recent literature.

Jan 1, 1985

By Eric Cather

A mineral investigation of prospects in the Sawtooth Mountains B Wilderness Study Area (WSA) by the U. S. Bureau of Mines in 1983 revealed none had mineral production, resources, or development potential. The area is underlain by tonalite and smaller amounts of schist, One developed prospect and one prospect pit are in the WSA. They are in schist similar to host rock which has yielded gold in nearby mining districts, Sand and gravel deposits in the WSA are large but too far from markets to be considered resources. No energy (oil, gas, coal, or geothemal) resources were identified in the USA.

Jan 1, 1984