Search Documents

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

By Irving Hartmann

Following the severe starch-dust explosion in the casting department of a large candy factory nearly 2 years ago, great interest has been shown in the explosive properties and the safe manufacture and handling of powdered starches. Under the auspices of the National Fire Protection Association, a committee has been formed to prepare a code aimed at preventing dust explosions in the confectionery industry. One objective of this code will be to reduce the explosion hazards of starches that are widely used for molding, dusting, and other candy-manufacturing processes. The explosibilities of starches and starch mixtures have been studied in the laboratories of the Bureau of Mines and elsewhere. The results of the initial experiments made by the Bureau on 10 samples of cornstarch and mixtures of cornstarch with other materials have been published. In response to numerous requests for additional information, further laboratory studies have been conducted. Data have been obtained on the effects of dust concentration, particle size, moisture content, admixture of .calcium carbonate, and on the effect of oil treatment on the explosibility of cornstarch. The results of this investigation are summarized in this report.

Jan 1, 1950

By Oliver Bowles

Since 1922 when the Bureau of Mines issued a report2 covering the slate industry in detail, changes in technology have taken place which have an important bearing on the industry. The present paper comprises a record of these changes. Though the value of slate, for roofing, structural, blackboard, sanitary, and electrical uses is generally recognized, it has many competitors. To meet this constantly increasing competition producers are promoting economies in manufacture, and improving processes, thereby lessening costs of production, and are placing on the market products of the highest possible quality, thus creating satisfaction and confidence on the part of the user. This endeavor to place the industry on a better basis, both as regards processes and products, is shown in the recent developments in technology which are presented herein. Valuable assistance in obtaining data for this paper was given by W. S. Hays, secretary of the National Slate Association, N. M. Male, president of the National Slate Association, and Robert Notvest, consulting engineer, Cleveland, O.

Jan 1, 1926

By R. V. Ramani

This volume is the third of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume II: Dragline Model, and Volume IV: User's Manual for OPMHS/2. The Mine Coordinate Generator System serves as an interface between the Geology and Reserves System (Volume I, final report) and OPMHS/2 (Volume IV, final report) to provide local mine grid information which is used as input to the decision making process and dynamic simulation routines of OPMHS/2. After the Geology and Reserves System has been successfully run for a property, a data base containing values for each grid cell covering the property is created at the end of execution, if chosen as an option by the user. The Mine Coordinate Generator reads this information and creates a special direct access data set from the sequential data input. When information defining the mine grid is read, the values present in the property grid are for the interpolation of values for each mine block.

Jan 1, 1985

By Edward M. Kawenski

Tests were made in the Bureau of Mines Experimental Coal Mine on stop-pings similar to those used in operating coal mines to obtain information on air leakage through the face and the rupture strength of a stopping subjected to a pressure differential. Block stoppings were made from cinder, slag, and gravel aggregates with and without mortared joints and coatings. Sheet stop-pings were uncoated brattice cloth and nylon or brattice cloth and expanded metal-lath coated with asphalt, latex, mortar, or rigid urethane foam. Limited data were obtained on air through stoppings subjected to simulated roof convergence and to shock forces created by the firing of an adjacent charge of explosive. The pressure differential required to rupture stoppings was determined. shows that coating the face of a stopping effectively reduces ail: leakage. Block stoppings, particularly those with mortared joints, are most resistant to pressure and shock forces than are sheet stop-pings. Where ground movement is a factor, sheet stoppings leak less air than block stoppings.

Jan 1, 1965

By N. S. Dalal, A. H. Hoffman, X. Shi, D. E. Banks, J. K. H. Ma, Y. Rojanasakul

Excessive production of reactive oxygen radicals by alveolar macrophages is proposed to play an important role in oxidative lung injury. A major product of oxygen radical formation is the highly reactive hydroxyl radical (•OH) generated via a biologic Fenton reaction. In addition to its known ability to induce lipid peroxidation, recent studies have suggested that the •OH may exert its cytotoxic effect through the alteration of [Ca2+], homeostasis. To test this potential mechanism as well as to investigate the relationship between •OH and Ca" overloading in cytotoxic injury, isolated rat alveolar macrophages were exposed to externally generated radical system, H2O2 (0.01 to 1 mM) and Fe (1 mM) and their [Ca2+] levels and cell injury were monitored using quantitative fluorescence microscopy with the aid of the specific Ca" indicator, Fura-2, and membrane integrity indicator, propidium iodide. Electron spin resonance measurements using the spin trap 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) confirmed the production of the .OH radical by this system. Upon the addition of the radicals, the macrophages displayed a rapid initial rise in [Ca2+] which was followed by a slower but more pronounced [Ca2+], elevation that reached a level 3 to 5 times higher than the basal level. This process preceded cell death as evident by nuclear propidium iodide fluorescence. Depletion of extracellular Ca" inhibited both the [Ca2+], response and cell injury. Preincubation of the cells with the Ca" channel blocker verapamil or .0H radical scavenger mannitol similarly inhibited the [Ca2+], rise and loss of viability. Firefly luciferase assay of cellular ATP content demonstrated that the alterations in [Ca2+], following .0H treatment preceded the depletion of ATP. Changes in membrane potential caused by Na* substitution with K* had no significant effect on either the unstimulated or stimulated [Ca"], levels. Taken together, these measurements indicate that .OH-induced injury in alveolar macrophages is associated with the alteration in [Ca2+], homeostasis. The mechanism of •OH-induced [Ca2+] loading is not due to nonspecific membrane damage or energy depletion, but mainly due to an increase in Ca2+ influx through Ca2+ selective channels. This Ca2+ over-load state as well as energy depletion caused by the oxidant may activate certain cellular degradative processes leading to cell injury and death.

Nov 1, 1995

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety, is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus,3/ gas masks, supplied-air respirators (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks),2 dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch, approval tests of other types of respira- tory protective equipment are conducted by the Health Branch, These branches are in the Health and Safety Division.

Mar 1, 1948

By R. F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Bureau of Mines has developed a general method for preparing solutions from a wide range of metal and mineral samples for chemical analysis. The development of the method from current knowledge of vessel material, pressure dissolution techniques, and the fluoride-boric acid reaction is given. The method uses 7 ml of a mixture of HC1-HNO3-HF acids in a ratio of 3.5:2:1.5 sealed in plastic bottles that act as pressure vessels when heated in a boiling water bath. A final volume of 100 ml is obtained by the addition of 93 ml of a 1. 5-pct H3BO3 solution to the bottles, which are reheated; precipitated fluorides as well as sample residue are dissolved by the fluoride-boric acid reaction. A copper slag and a steelmaking slag treated using this method were analyzed by atomic absorption spectroscopy yielding values for Si, Mg, Ca, AI, Fe, Mn, Na, As, Pb, Sb, and Zn very close to certified values with an average relative standard deviation of 2.13 pct. The low cost, reduction in preparation time, ease and safety of sample handling, conservation of reagents, and ability to dissolve volatile materials without loss make this method superior to traditional wet digestion techniques for many materials, and ideal for use with atomic absorption, and optical emission or X-ray emission spectroscopy.

Jan 1, 1980

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines (USBM) and the US. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSRYs were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 1994

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

Lower the respirable dust expo-sure of longwall mine workers by reducing the amount of air-borne respirable dust generated during coal extraction. Approach Increase the moisture content of the coal seam through water infusion before the coal is mined. How Water Infusion Works Increasing the moisture content in coal tends to prevent respirable dust from becoming air-borne during mining and transport. The moisture content of the coal seam can be increased by infusing water into the seam. Water under pressure is forced into the cracks (cleats) of the coal seam through sealed bore-holes. The effectiveness of water infusion is a function of the amount of water the coal seam accepts (its infusibility), which depends on the cleat density (cleat spacing) and cleat size (crack diameter). Thus the effect of water infusion on dust control depends mainly on coal seam characteristics. Water infusion techniques are generally used to restrict the flow of methane gas to the working face; however, the technique provides an alternative dust control method in mines with severe dust problems which limit production.

Jan 1, 1987

By F. J. Palumbo

Effective recycling or disposal of flue dusts is a continuing problem for copper, brass, and bronze smelters. Over 300,000 short tons (st) of dust is generated annually by U.S. secondary copper, brass, and bronze smelters. The Bureau of Mines has developed an alkaline leach method for recovering metal values from copper converter flue dust containing zinc, tin, lead, and copper. The dust was leached with a hot solution of ammonium chloride and ammonium hydroxide to solubilize ZnO. All of the tin (as Sn02) and the metallic copper, lead, and zinc, as well as possible insoluble compounds of each, report to the residue. Dissolved copper and lead salts are removed from the leachate by cementation with granular zinc. Zinc oxide is precipitated by diluting the leachate with water. The tin-rich (9.8 pct) residue has a ready market. The cement product is recyclable to the smelting operation. The ZnO is at least 97 pct pure and has potential marketability.

Jan 1, 1985

The U.S. Bureau of Mines evaluated water-jet-assisted longwall shearers in full-scale laboratory tests and underground. Both test programs showed that use of high-pressure water did little to reduce the shearer motor energy required to maintain a given cutting rate. However, three other major benefits were achieved with the use of water-jet-assisted cutting. At a pressure of 1,800 psi, respirable dust levels were reduced about 80 pct compared with the dust levels of the conventional water spray system operating at 340 psi. Operating at higher pressures required for water-jet assist also resulted in an increase in the average size of coal cut, which translates into a decrease in product fines. Finally, although no controlled measurements of bit wear as a function of water pressure were made, mine personnel reported that the shearer bits lasted longer when water-jet-assisted cutting was used.

Jan 1, 1989

By R. V. Higgins

The, large volumes of low A. P. I. gravity oil that will remain in many shallow fields of California when such oils no longer can be recovered profitably by pumping are important potential sources of oil when ways and means are found to remove them from the reservoir sands. Estimated ultimate oil recoveries in many of the "low-gravity fields" of the San Joaquin Valley in California indicate that less than 25 percent (on the average) of the original oil will be recovered. These oils have viscosities of 1,000 or more centipoises at reservoir temperatures and, because of their high viscosity and low intensity of the reservoir pressure, the quantities that will be retained in the sands ultimately are so large and their recovery is such a challenge to petroleum engineers that the Bureau of Mines has made the study of their possible recovery one of its major projects. The fact that a slight increase of temperature materially reduces the viscosity of low A. P. I. gravity oils has 'prompted the use of various means for increasing the temperature of the oil in the reservoir sands and hence the rate of flow and Completeness of recovery of the oil. Hot oil, hot water, heated air, and natural gas, steam, super-heated steam, and the products of combustion have been circulated in wells to raise the temperature of the oil it the sands; electric heaters have been installed in wells, and butane and air have been intermittently exploded and the flames propagated through the tubing to the "pay" zones. None of the methods, however, have been entirely satisfactory for the recovery of large quantities of oil.

Jan 1, 1949

By Robert Hall

The Lynch Creek beryllium-tungsten prospect was investigated as part of the domestic beryllium resource studies by the Bureau of Mines. This prospect is in the Birch Creek mining district, Lander County, Nev., 9 airline miles south of Austin. A tungsten mine was operated intermittently from 1952 to 1957. Beryl was identified in the pegmatite dikes in 1960, and the lode claims were relocated. No beryl has been produced. Rocks in the area are Paleozoic sediments2 cut by pegmatite and aplite dikes and quartz stringers. Beryl occurs in random pockets, as disseminations throughout the dikes, and in occasional pockets in the quartz stringers.

Jan 1, 1962

By Fei Chen, Lesley J. Gaydos, Laurence M. Demers, Douglas C. Kuhn

The fibrogenic effects of silica in experimental animals and humans has been extensively studied (I 7, 20). However, the pathogenesis and molecular mechanisms underlying lung injury and fibrosis resulting from silica exposure remain to be elucidated. It is well-documented that silica can stimulate monocyte-macrophage lineage cells to produce cytokines and growth factors, including interleukin-I (IL- I) (20), tumor necrosis factor-ex (TNF-cx) (I 7), insulin-like growth factor-I (IGF-1) (4), and transforming growth factor-P (TGF-P) (24). Consequently, it has been suggested that the fibrogenic effect of silica may be mediated by cytokines in the fater stages of silicosis. During the early phase of interaction between silica and the pulmonary alveolar macrophage, several direct and indirect lines of evidence suggest that reactive oxygen intermediates (ROI) may play a pivotal role in silica- induced tissue damage (2I, 22). One of the most important components of and contributors to ROI is nitric oxide (NO) produced from L-arginine and molecular oxygen under the catalytic influence of NO synthase (NOS) (I 9). At present, at least three NOS genes have been cloned: a constitutive neuron NOS, a constitutive endothelial cell NOS and an inducible NOS (iNOS) (16). A number of factors have been shown to differentially induce iNOS gene expression in different cell lines including bacterial cell products and foreign antigens. During inflammation, NO is a double-edged sword in terms of the host immune defense mechanisms and the physiologic response to an inflammatory insult. The macrophage is one of the major cellular sources of NO. During the early phase of acute inflammation, NO produced from the macrophage appears to facilitate the clearance of pathogens and promotes a local relaxation effect on the microcirculation of vascular smooth muscle. When the production of NO is left unattenuated, especially under oxidative stress, direct cytotoxic effects of NO can emerge through the formation of peroxynitrite as a result of a reaction between NO and superoxide (2).

Jan 1, 1998

By N. S. Dalal, X. Shi

While it is known that vanadate and related compounds of pentavalent vanadium ( V (V)) exert potent toxic effects on a wide variety of biological systems, the underlying biochemical mechanism is still not fully understood ( 1- 3). One of the pathways is thought to involve the oxidation of NAD ( P) H. Thus, considerable effort has been devoted to finding the mechanism of NAD ( P) H oxidation by Vcvi (1-15). Erdmann et al. (5) first noted that vanadate stimulated the oxidation of NADH by plasma membranes and attributed this effect to a membrane containing NAD(P)H-dependent V(V) reductase. Later studies by Liochev and Fridovich indicated that endogenous superoxide ( 02 ) plays a central role in this reaction ( 4, 12, 13) . They proposed that NAD ( P) H dehydrogenases or oxidases produce 02, which causes VCV ) to stimulate NAD ( P) H oxidation via the following free radical chain mechanism ( 4, 12, 13) :

Mar 1, 1992