Search Documents

By Stephen D. Cramer

The objective of the present studies was to develop thick adherent and coherent coatings of platinum and palladium on refractory metals and other substrates of industrial and engineering importance. Existing platinum and palladium electrolytes were modified to make them suitable for the electrodeposition of thick deposits. The optimum operating conditions for these electrolytes were established. Pretreatment procedures for columbium, copper, graphite, molybdenum, nickel, stainless steel, tantalum, titanium, tungsten, vanadium, and zirconium substrates were studied. New pretreatment procedures for columbium, molybdenum, stainless steel, tantalum, tungsten, and nickel were developed. The internal stress and hardness of selected electrodeposits were measured. The effects of heat treatment upon the properties of electrodeposits were studied.

Jan 1, 1967

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By L. Keith Hudson

The purpose of this study is to provide data that demonstrates that the Alcoa flash calciner design can be used for the decomposition of AlCl3?6H2O to A1203. Heat and material valance data for calcination provides data on the partial pressure of HCl in the off-gases. Experimentally determined data for the HCl partial pressure, over solutions expected in producing alumina from clay by the hydrochloric acid process, show that HCl can be absorbed from the off-gases into process solutions to effect crystallization of AlCl3?6H2O.

Jan 1, 1979

By E. G. King

In continuation of the study of thermodynamic properties of the common interoxidic compounds of ferroalloy elements, this report gives the results of low-termperature heat-capacity measurements and entropy evaluations of the monotungstates of sodium, magnesium, and calcium. Previous reports4 5/ of this laboratory dealt with low-temperature heat capacities, entropies, and heats of formation of the sodium vanadates. Heat-capacity measurements of the monotungstates of sodium, magnesium, and calcium (Na2W04, MgW04, and CaW04) were conducted throughout the temperature range 51° to 298° K. The entropies at 298° K. were evaluated and then combined with entropy data for the elements and oxides to obtain entropies of formation. This information is an essential part of the data needed for thermodynamic appraisals of chemical reactions of these substances. No similar data for any tungstate are to be found in the literature.

Jan 1, 1961

By J. S. Browning

The purpose of this Bureau of Mines project was to develop a method for recovering kyanite and sillimanite from the present zircon-mill tailing of the Jacksonville and Starke, Fla., plants of Humphreys Gold Corp. The kyanite and sillimanite in the ore are not being exploited at present, but procedures for recovering the two minerals were worked out by the Bureau in the interest of conserving natural resources. The current zircon-mill tailing of the Starke plant contains up to 20 percent of a mixture of kyanite and sillimanite. A similar product of the Jacksonville plant contains up to 15 percent kyanite and sillimanite. The average annual production of the tailing now being stockpiled contains several thousand tons of the two minerals. Laboratory batch-flotation tests were made on the materials to determine the feasibility of flotation methods for recovering high-grade concentrates. Various reagents were employed under different conditions to determine the optimum conditions for flotation of kyanite and sillimanite and retardation of the gangue materials. The results of the preliminary flotation tests were encouraging enough to warrant more comprehensive testing of a larger sample of the ore in the laboratory pilot plant.

Jan 1, 1956

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of liquid Al-Si alloys with the high-temperature galvanic cell Al(1)//Al+3(AlC13 in NaCl?KCl)//Al-Si alloy(1). Activities of aluminum and silicon (referred to pure liquid metals) show a pronounced negative deviation from Raoult's law in liquid Al-Si alloys containing 0.9 to 35.2 atomic-percent silicon. Activity coefficients and the properties [?Gi, ?GxS ,?H, ?G, ?Gxs , and ?S] have been derived from the experimental data and are summarized in tables and illustrations.

Jan 1, 1974

By N. S. Dalal, X. Shi

"SUMMARYElectron spin resonance (ESR) measurements provide direct evidence for the involvement of the glutathionyl radical, as well as an isolable Cr(V)-glutathione intermediate in the Cr(VI) glutathione redox reactions. These results indicate a new mechanism for the reduction of Cr(VI) by glutathione in relationship to cellular environment and suggest that synergistic reactions of Cr(V) and GS· might be responsible for the (unexpected) increase in the Cr(VI)-induced DNA-strand breaks at high glutathione levels.INTRODUCTIONWhile the reduction of Cr(VI) by glutathione (GSH) is thought to be a critical' step in the pathogenesis of the Cr(VI)-exposure related carcinogenesis1- 4, the exact reduction mechanism is not yet understood. The following reaction steps have been suggested :(A) Initial step:Cr04 2- + GSH - GSCrOa - (1)(B) At high GSH levels:GSCroa- + GSH - Cr( IV) + GSSG (2)(C) At low GSH levels: GSC rO a - - Cr ( V ) + GS ·(3)Thus far, however, in these reactions, the GS· radical has eluded spectroscopic detection, while the evidence for the Cr(V) formation has been reported positives as well as negative2·. Her~ we present spin-trap ESR evidence for the formation of the GS· radical, and a definitive ESR detection of an isolable cr(V)-GSH intermediate in Cr(VI)-GSH reactions.MATERIALS. AND METHODSESR spectra were obtained at X-band (-9.7 GHz) using a Bruker ER200D ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR Gaussmeter (Bruker, Model ER035M) and the microwave frequency was measured with a Hewlett-Packard (Model 5340A) frequency counter. The spin probes, a-(4-pyridyl-1-oxide) -N -tert-butylnitrone (4-POBN) and 5,5-dimethyl~1-pyrroline-1-ox1de (DMPO) were purchased from Aldrich, K2Cr201 from Fisher and used without further purification. All experiments were done at room temperature."

Jan 1, 1989

By Herbert R. Babitzke

As part of a project to develop refractory metal alloys suitable for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation-hardening techniques to columbium and tantalum alloys. Thirty-three alloys were evaluated to determine their formability, strength, and oxidation resistance. Three alloys had tensile strengths near 40,000 psi at 1,200° C: Cb-1N-5W-5V-10Hf (No.4), Cb-15Hf-5W-0.5B (No. 31), and Cb-15Hf-SW-IB (No. 32). Oxidation resistance of the high-strength alloys was good. Alloy4 gained only 34 mg/cm2 at 1,200° C, and 21 mg/cm2 at 1,000° C in 2 hours. Hot forming was done without any protection from oxidation.

Jan 1, 1968

By C. A. Herbert

The mine of the Alpha Portland Cement ..Co., Iroaton, Ohio, ..working in. a. bed of limestone 96 feet thick at a depth of approximately 510 feet below the surface, has established a won¬ derful safety record, having operated 6 years—frcra September 21, 1926,. to September 21, 1932 - without a lost-time accident. This mine, with 61 to 86 employees (average 68) and daily output of 1,000 to 1,200 tons of limestone, operated 1,041 days during the 6-year period, or the equivalent of 578,894 man-hours of exposure. ...... ... . Immediately above the limestone is a 20-foot .bed of hard..sandstone.. At present about 10 feet of limestone is left up as. a roof and.about. 42 feet is being extracted. Of the lower portion of the bed it is believed that about. 25 feet. ..immediately below . the .present workings is suitable for cement and will be extracted later. The mine workings are reached by two rectangular concrete shafts, one a 2-compartment hoisting shaft and the other a 2-compartment air and escape shaft- In the latter shaft one compartment is used as an airway and the other, as a cage compartment fo.r a man and material cage. .. . - . The tipples at both the air shaft: and. hoisting shaft are-of steel. The.ground landings at both shafts are fenced in with hand-operated gates in front of the cage compartments.- The two shafts and the crushing plant, which .is.a part of the hoisting shaft-tipple structure, are adjacent to the mill buildings. The rock is hoisted on self-dumping cages in 4 ton capacity, end-gate, steel cars. An electric hoist with automatic overwind device is used at both the main shaft and air shaft. The controls for the main hoist are in the tipple where the engineman is stationed and from which point he has an unobstructed view of both the ground, landing and the cage coming into the dump.

Jan 1, 1933

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By B. W. Gandrud, G. T. Bator

The recent introduction of small coal jigs in Alabama to meet the needs of truck - mine operators for cheap and economical cleaning equipment marks another step in Alabama's pioneering record in the mechanical cleaning and preparation of coal . During the past 4 or 5 years a number of these small jigs , with capacity of 5 to 10 tons per hour , have been installed at Alabama truck mines and at a few truck mines in Illinois , Tennessee , and Pennsylvania . Most of the installations have been at mines that specialize in the production of domestic , stoker coal . This report describes three models of small jigs and includes performance data obtained recently on one of the models by the Bureau of Mines, United States Department of the Interior , in cooperation with the University of Alabama, Tuscaloosa , Ala . , for the purpose of comparing it with fullsize jigs on a performance basis . With literally hundreds of truck mines now in operation throughout the country , it has been assumed in preparing this report that there is widespread interest in the availability of small - scale inexpensive preparation equipment for use at such mines in the production of steam and domestic coal and in some instances coal for manufacture of coke . Practically none of the coal from Alabama truck mines is scld to coke - oven plants ; but in some sections of the country truck mines supply a considerable amount of coking coal, and the use of small, inexpensive washers at some of them might be very advantageous during the present war emergency from the standpoint of increasing pig - iron production through improvements in coke quality .

Aug 1, 1943

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Eugene Frey

"INTRODUCTION The Good Fortune mine was sampled by an engineer of the Bureau of Mines in June 1944. Project 984 was set up under the strategic minerals program to make old workings accessible for this sampling program. Actual operations commenced June 1, 1944, and were completed June 30, 1944.The deposit was visited and discussed briefly by Sidney H. Ball 3/ of the Federal Geological Survey in the summer of 1906 and by H. M. Chance 4/ several times from 1887 to 1900.LOCATION AND ACCESSIBILITYThe Good Fortune mine is situated in the Hartville mining district in Platte County, Wyo., approximately 9 miles northwest of the town of Guernsey. The property is about 100 miles north of Cheyenne, Wyo. (fig. 1).ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metal¬lurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1947

By A. A. Cochran

The objective of the research was to determine the final distribution of cerium additions to steel, their effect on sulfide inclusions, and the usefulness of radiotracer methods in investigating steel problems. Fifty-gram heats of steel were prepared that contained either cerium 141 and nonradioactive sulfur, or sulfur 35 and nonradioactive cerium. These steels were studied by autoradiography, measurements of their surface radioactivities, optical microscopy, and chemical analysis. Samples of the crucibles were analyzed quantitatively for cerium or sulfur by radioactivity counting methods. The addition of cerium to steel melts reduced the size and number of iron sulfide inclusions in the resulting steel. A significant fraction of the sulfur and most of the cerium penetrated into the MgO crucible during the melting operation, The cerium inclusions in steel were identified as cerium sulfide. Radiotracer methods were found to be versatile and highly sensitive.

Jan 1, 1963

By Howard P. Hamlin, John W. Sweeney

Shales from 14 locations in Indiana were sampled , tested , and evaluated to determine feasibility of producing lightweight aggregates by rotary - kiln and sintering methods . Sampling procedures and the geology of the significant shale units are discussed . Preliminary testing was conducted in a muffle furnace , and continuous tests were made in a 16 - inch by 14 - foot rotary kiln . The aggregate weighed 37.0 to 47.2 pounds per cubic foot . Concrete cubes employing the aggregate were tested to determine the qualities of the concrete . Compressive strength of the concrete using seven bags of cement per cubic yard , after autoclave curing for 6 hours , ranged from 3,600 to 5,850 pounds per square inch . Four samples made suitable lightweight aggregate in the laboratory rotary kiln . Four samples tested by sintering methods made unsatisfactory aggregate .

Jan 1, 1965

By S. P. Holt

The Rush & Brown mine has been one of the most consistent small producers of copper ore in the history of Alaskan mining. Approximately 50,000 tons of ore have been shipped to smelters from the property. Production has been made from two distinct and separate ore bodies of dissimilar types. The Shear Vein deposit has been mined to a depth of 500 feet below the surface without a reduction in the size of the ore shoot or the grade of ore. The Magnetite ore body has been partly mined to a depth of 200 feet below the surface. Because of the favorable production record of the Rush & Brown mine, the present need for copper and the fact that the owners were attempting to place the mine in production, it was deemed advisable to investigate this property under the Strategic Minerals Act of 1939 as a possible source of copper.

Jan 1, 1948