Search Documents

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

By ALBERT LONG, Wing G. Agnew, FELIX CHAYES, Alton Gabriel, Leonard Obert

Although the technique of diamond drilling was developed nearly 80 years ago, the use of this process as an aid to mining and other fields of engineering has increased greatly during the last decade , primarily as a result of the development of the cast -set bit , which now largely replaces the hand - set types , and of the use of bort instead of carbons . Since this transition to cast - set bits and bort diamond , many papers ( 1-14 ) have been written on the application of diamond drilling to various engineering problems . These papers contain , besides specification of the problems , some information on the labor and bit costs and a few data on drilling technique . These data , however , are subject to restricted interpretation owing to the large number of variables , which are not controlled in field drilling . Only one paper has come to the attention of the authors , namely , that by Sundberg and Lindqvist ( 16) , which reported a study of diamond drilling under controlled conditions . This paper was written early in the transition period, and the data and conclusions presented therein have had , without a doubt, considerable influence on the development of presentday diamond bits and In view of the fact that during the last 10 years thrilling procedure . have been new developments in diamond bits. and new applications of diamond drilling , a general program of research has been inaugurated to study the problems resulting from these changes .

Mar 1, 1947

By John W. Walkiewicz

The U.S. Bureau of Mines has conducted studies to utilize rapid microwave heating to stress fracture ore samples. Iron ores containing hematite, magnetite, and goethite were subjected to microwave energy in batch operations at 3 kW and heated to average maximum temperatures between 840 and 940 °C. Standard Bond grindability tests showed that microwave heating reduced the work index of iron ores by 10 to 24 pct. In a microwave chamber designed to simulate a continuous throughput operation at 3 kW, the grindability of a taconite ore was improved by 13 pct at a bulk temperature of 197 °C. Because stress cracking occurred at a lower temperature, less energy was consumed. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous, belt-fed applicator. A significant improvement of grindability was obtained with a larger rod mill feed size in comparison to a minus 6-mesh Bond feed.

Jan 1, 2010

By Roy Bartholomae

Noise generated by continuous mining machines in underground coal production is an important health hazard. Bureau of Mines Contract J0387229 covers investigation of this noise through laboratory tests of simulated cutting operations and through in-mine noise measurements. The results of these investigations indicate that coal cutting noise and conveyor noise are dominant sources of mining machine operational noise. Typical noise levels for both cutting and conveying operations are approximately 97 dBA (decibels A-weighted). For full operation of all machine systems, the overall sound pressure level is approximately 101 dBA. In-mine and laboratory test results show excellent agreement in both A-weighted overall levels as well as in A-weighted one-third-octave band spectra.

Jan 1, 1983

By C. B. Manula, R. L. Sanford, R. A. Rivell

This report was prepared by The Pennsylvania State University under USBM Contract No. 60111808. The contract was initiated under the coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with M. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines.

Jan 1, 1974

By D. R. Mathews

The solubility of carbon in electrorefined vanadium was determined to be approximately 0.27 wt pct at the eutectic temperature 1,650° C and 0.03 wt pct at 700° C. The tensile strength and hardness of vanadium increased with car-bon content to the solubility limit, but this effect was small, probably because of the narrow solubility range. Between the solubility limit and 0.3 weight-percent carbon, the second phase had essentially no strengthening effect in vanadium. The second phase, observed metallographically at the grain boundaries and within the grains, was shown by autoradiography to contain high-carbon concentrations. This second phase was identified as VgC by X-ray analysis. The VgC in the grain boundaries contributed largely to the poor cold-and-hot workability of vanadium-carbon alloys. Increased concentrations of V2C occurred at the grain boundaries of the high-carbon alloy ingots as a result of homogenization at 1,600° C for 1 hour. Alloy ingots containing more than 0.36 wt pet carbon (a calculated 2.9 wt pct VaC) following homogenization, cracked severely and failed by intergranular fracture upon swaging at 900° C.

Jan 1, 1965

By G. R. Hopkins

Although many small refineries were dismantled in 1934 the total number of plants, including a few under construction, increased from 604 at the beginning of the year to a new high of 638 on January 1, 1935. The capacity also reached a new record, the total of 4,072,400 barrels of crude oil daily being about 45,000 barrels higher than the previous high of January 1, 1932. The number of refineries increased materially in 1933, following construction in east Texas and the building of many small plants in the Rocky Mountain district and elsewhere. Most of the new plants of 1933 were built to provide an outlet for crude or because the ratio between crude oil and gasoline prices appeared conducive to profits However, low gasoline prices and increased costs in 1934 dispelled the hopes for profits; many plants were shut down, and some were dismantled. The number of operating plants declined from 454 on January 1, 1934, to 435 on January 1, 1935, but the number of inactive plants increased from 137 to a new high of 196 during the same period. As indicated above, new construction was at a minimum in 1934, and on January 1, 1935, only 7 plants were being built.

Jan 1, 1935

By George T. Faust

The petrographic microscope plays an important role in the mineral dressing of nonmetallic materials. Petrographers and mineral technologists have evinced an interest in the technique developed, specifically, for mineral-dressing problems. The following dissertation makes the informa¬tion more generally available. ACKNOWLEDGMENTS The authors are indebted to O. C. Ralston, chief engineer, Nonmetals Division, and to Will H. Coghill, supervising engineer of the Southern Experiment Station for a critical reading of the manuscript. They are also indebted to their colleagues for technical information obtained in the course of cooperative work, in particular to J. B. Clemmer for the use of the data on fluorite.

Jan 1, 1940

By James W. Ballard

The facts are generally accepted that an atmosphere containing large quantities of any dust is objectionable to breathe and that some dusts are more dangerous than others. Therefore, knowledge of the com-position of dusts is important in evaluating the hazard entailed on exposure. At present, free silica, of which quartz is the most abundant form, is considered one of the most significant dusts, from the standpoint of pneumoconiosis, and one State5/ has established permissible limits of air dustiness on the basis of the free-silica content of rock. The amount 06 free silica in materials used for rock dusting also has been limited.6/ Determination of free silica or quartz, therefore, is important.

Jan 1, 1940

By L. D. Wyant

That natural gas-gasoline can be used to advantage as a refrigerant is suggested by the fact that the "make" tanks and other parts of the equipment of gasoline plants frequently become coated with frost. The experiments reported in this paper confirm this assumption and indicate that volatile gasoline can be use used to advantage in many refrigerating plants. The Bureau of Mines is making a study of wax distillates in order to find out why satisfactory lubricating oils and waxes can be made easily from certain crude oils and only with difficulty from others. In the commercial distillation of crude petroleum it is customary to separate the distillates into the following groups: (A) Gasolines and naphthas, (B) Kerosenes, (C) Gas oil, and (D) Wax distillate (consisting mostly of light lubricating oil together with small amounts of paraffin Wax).

Jan 1, 1923

By William O. Vanderburg

Tis paper describing the mining practices at the Cold Springs mine of the Wolf Tongue Lining Co. at Nederland, Colo., is one of a series of similar papers prepared by the Fureau of kines on mining practices, methods, and costs at various mines in the United States. The writer acknowledges the assistance of William Leach and William T. Todd, manager and mine superintendent of the Wolf Tongue Mining Co., respectively, in the preparation of this paper.

Dec 1, 1932

By D. Harrington

Approximately 2,000 persons are killed annually in the coal mines of the United States. There is no question that this number is at least double and probably treble what it should be and by all means the least excusable of the fatalities are those caused by explosions and fires. Fatalities from explo- sions and fires in coal mines are almost invariably caused by carelessness or negligence. Table 1 indicates that the fiscal year ending June 30, 1931, ras by no means a satisfactory one as regaris either the number of explosions or the number of persons killed by them. This tabulation lists all ignitions to which the attention of the personnel of the safety division was called and in- cludes not only major disasters, but also explosions in which fewer than five were killed, as well as several explosions from which no fatalities resulted. It will be noticed that last year there were 26 explosions in mines in 10 States of the United States, resulting in 217 deaths. In the previous year there were 34 explosions with a death list of 199, and in the year before there were 38 explosions with a death list of 139. Hence, the past fiscal year had distinctly a poorer record of fatalities from mine explosions than either of the two previous years. Of the 26 explosions in the past fiscal year, Pennsylvania had 7, West Virginic 4, New Mexico and Ohio 3 each, Alabama, Oklahoma and Washington 2 each, and California, Illinois and Indiana 1 each; the one in California was in a tunnel being driven for water purposes but giving off explosive gas (methane). In fatalities Ohio had the worst record with 38, Oklahoma came next with 45, then Indiane with 38, and Pennsylvania with 23; although Alabama had 2 ignitions and Washington 1, they caused no fatalities. Utch, Colorado, and Kentucky had no explosions reported by the safety division of the Bureau of Mines during the past fiscal year, but were on the list for the previous year, though in the case of Colorado there were no fatalities. On the other hand, Indiana and New Mexico, neither of rhich was charged with an explosion in the two previous years, were on the list for the past fiscal year; New Mexico had the bad record of three explosions, though fortunately with but a total of eight fatalities. Ohio reported 3 explosions to the safety division of the Bureau of Mines in the past fiscal year, 2 in the pre- vious year, and 3 in the year before that, or 8 in the past three fiscal years with 92 fatalities; all of these eight explosions were in open-light mines.

Dec 1, 1931

By Larman J. Heath

Liquid incendiaries were burned within the interstices of several different types of sandstone cores to determine the technical feasibility of increasing sandstone permeability by this method. Fuel-oxidant mixtures were tested in 186 cores; six cores exploded when ignited. In virtually all instances, the explosion completely pulverized the sandstone cores. In addition n those cores damaged by explosions, 24 cores were fractured so severely that permeability tests were impossible. Although combustion gener¬ally increased the permeability, specific mixtures at given pressures were inconsistent in their ignition and burning behavior. Tests indicated that the heat of burning incendiaries significantly increased sandstone permeability. The improved permeability ratios were usually less than 2, but one was 10.3. Permeability alteration by other in situ methods was not as effective as that by flame propagation.

Jan 1, 1971

By J. W. Town

As part of the Federal Bureau of Mines titanium resources examination program, samples from seven deposits in the Pacific Northwest were tested for amenability to various beneficiation techniques. The samples obtained by the Bureau's Office of Mineral Resources at Spokane, Washington represent a large potential source of titanium. This report summarizes the results of tests at the Bureau's Metallurgy Research Center, Albany, Oregon. Recoveries from tabling placer samples were about 50 percent at grades of 30 percent titanium dioxide. Flotation was the most effective method for concentrating the fine ilmenite in clay samples; recoveries of approximately 50 30 percent titanium dioxide. Flotation was the most effective method for concentrating the fine ilmenite in clay samples; recoveries of approximately 50

Jan 1, 1961

By Oliver Bowles

Limestone, including dolomite, is the most widely used of all rocks - nearly 300 million tons annually in the United States alone. It occurs in some form in every State and is produced in thousands of localities. Because of its attractiveness, substantiality, and durability it is employed extensively as a building stone. In crushed and broken form it is used for concrete aggregate and railroad ballast and in highway construction, metallurgy, agriculture, and a host of chemical and industrial processes. This paper proposes to furnish general information on the origin and occurrence of limestone and dolomite, chief production centers, major uses, and methods of quarrying and preparing stone for market. Footnote references will guide the reader to sources of more complete information.

Jan 1, 1956

By D. H. Carlson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory-grade instruments. Concentrations of CO and CO2 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for CO2. EMA¬ measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO2 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 2010

By M. P. Youker

USE OF LOW-PRESSURE GAS BURNERS IN OIL- FIELD BOILERS

Feb 1, 1922

By Lung Cheng

Based on earlier tests that showed steel to be much more likely to cause frictional ignition than tungsten carbide, the Bureau of Mines redesigned coal-cutting bits to reduce the hazard of face ignitions. Two bit designs--a mushroom-shaped bit with a conical shank and a dove-tail bit with a rectangular shank--are described, as well as bit wear tests conducted in the laboratory and in an operating coal mine. In laboratory tests, for 1/8-, 1/4-, and 1/2-in-deep cuts and cutting speeds of 280, 500, and 660 ft/min, the mushroom bit had significantly longer tip wear life than the conventional bit; the dovetail bit was also superior to the conventional bit. Results of in-mine tests on the mushroom bit agree well with laboratory results. In-mine tests of the dovetail bit are underway.

Jan 1, 1983

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007