Search Documents

By Friedel. Michael J.

The U.S. Bureau of Mines investigated acoustic emission (AE) and the Kaiser effect in six types of rock: St. Cloud gray granodiorite, Barre granite, Dresser basalt, Salem limestone, Berea sandstone, and a volcanic tuff. AE signatures were used for interpreting the rock deformation stage and for indicating mechanisms of failure in uniaxial compression. The research demonstrated the advantages of using the volumetric stress-strain curve, as opposed to the more conventional uniaxial curve, for correlating AE response signatures with deformation stages and fracture processes in the rock. Standardized experimental procedures were used for the AE monitoring. The Kaiser effect was shown to be capable of determining prestress levels to within a few percentage points in uniaxial compression tests. Also, prestress memory was shown to be retained in the rock for periods of up to at least. 5 months, the maximum period of testing. The Kaiser effect AE technology holds promise for providing a comparatively inexpensive and less complex method for examihing stress history in rock. However, since the conftning stress has a pronounced influence on the Kaiser effect, it must be considered in developing technology for determining peak fteld stresses based on the Kaiser effect.

Jan 1, 1990

By F. R. Cattoir

The Federal Bureau of Mines refined chromium from an aqueous electrolytic process in molten sodium chloride-chromium chloride electrolytes. Oxygen and nitrogen contents were reduced by a factor of 10 to 40, but most other impurities were little changed. The product usually contained a little more iron than the feed. Since iron was entering the bath from the iron pot and the graphite liner at a nearly constant rate, contamination of the chromium deposits by it was more serious at low currents and deposition rates. A few runs in an iron cell with a nickel liner yielded chromium containing one half as much iron as the feed, but up to 1.5 pct. nickel. In all cases the anode feed lay in the bottom of the container, which itself was used as the anode connection. With a 12-in. cell, variations in applied voltage from 0.05 to 1.5, in current from less than 10 to over 100 a., and in initial cathode current densities from less than 100 to over 2,000 a./sq.ft. had little or no effect upon the analysis of the metal produced) except for iron content. Changes in bath analysis from 3 to 11 pct. chromium were also without effect. These changes did bring about large differences in the physical forms of the crystals obtained. The thick heavy crystals produced at low voltage and current contained voids which made them difficult to leach free of chlorides. Easiest to leach were the thin leaf-like crystals obtained at around 1 v.

Jan 1, 1960

By John Gross

Studies in grinding efficiencies carried out at the Midvale plant of the U. S. Smelting, Refining & Mining Co. and at the Tooele plant of the International Smelting Co. Were made possible by the cooperation of these two companies with the U. S. Bureau of Mines. Mr. Alan Probert of the U. S. Smelting, Refining & Mining Co. and Mr. E. C. Peterson of the International Smelting Co., devoted their entire time to the work during the respective tests, and their services are hereby gratefully acknowledged. It is a pleasure to acknowledge also the assistance and kindness of the staffs of both companies in making it possible, at considerable trouble and expense, to sample the entire mill circuits and in furnishing the necessary supplies and special apparatus required in the work.

Jan 1, 1929

By J. H. Soulé

"The Copper King copper-gold-silver deposit was discovered about 1880. Various individuals and companies have been interested in the deposit and considerable work has been done, although production, if any, has been small. The deposit is located in the western part of Laramie County Wyo., and is favorably nituated with respect to rail and truck transportation and high-tension power facilities.Mild summers and cold winters characterize the climate. Precipitation averages between 16 and 17 inches annually, with considerable snowfall in the winter. Permanent streams are small and most available water in being stored for use by Cheyenne, Wyo. Range grasses comprise the bulk of the vegetation, with small treed and shrubs common in the most rugged areas.The deposits lie upon land owned by Wyoming, now leased by a group of Wyoming and Colorado businessman constituting the Copper King Mining Co.Primary copper-gold mineralization seems largely confined to an equigranular, relatively fine grained gneiss that is part of a pre-Cambrian complex of metamorphic rocks ranging from schists to pegmatites. The copper minerals are oxidized to a depth of from 100 to 150 feet, with the occasional occurrence of secondary minerals at greater depths. The copper minerals chalcopyrite, malachite, chalcocite, bornite, cuprite(?), and some native copper were observed in Le deposit.In addition to the 4,030 feet of diamond-core drilling in 11 holes done on the deposit by private companies, the Bureau of Mines drilled 3 holes for a total of 2,630 feet. The sample results of this drilling plus available data from previous drilling and sampling are appended to this report."

Jun 1, 1955

By G. A. Smyres

A GaC12--B2 l-eachtng procedure and meEal-recovery method for treating an arsenical Cu-Co sulfide concentrate was developed by the Bureau of Mines as an alternative to smelting, which is no longer considered an environmentally acceptable method for treating arsenic-containing ores. The procedure involved leaching in a CaC12 solution with CaC03 for 96 h at 26 pct solids (concentrate and CaC03), 1150 C, and a pressure of 50 psig (345 kPa) with oxygen. More than 98 pct of the cobalt and 97 pct of the copper were extracted, and 99.98 pct of the arsenic and 99.9 pct of the iron remained in the leached residue. A filtration rate of 2.9 gal/(ft2.h) [118 L/(m2.h)] and a cake formation rate of 36 Ib/(ft2.h) [172 kg/(m2.h)] were obtained by filtering reacted pulp at 1000 C. More than 99 pct of the copper in the pregnant solution was extracted as CuCl2 by golvent extraction with a new copper extractant. Copper was stripped from the loaded organic with a sulfate-chloride solution, which was used as the anolyte for electrowinning of copper in a membrane cell. Copper plate produced was more than 99.99 pct pure and requi.red 0.81 (kW'h)/lb Cu [1.78 (kW·h)/kg Cu]. Cobalt sulfide was precipitated at pH 3 with Ca(HS)2.

Jan 1, 1986

By C. W. Huggins

The primary objective of this Bureau of Mines research was to measure the size distribution of respirable quartz collected at metal mines, nonmetal mines, and processing plants to select the best reference standard for use in quantifying quartz in mine and plant dust samples. The secondary objective was to size all the nonquartz particles collected at the same sites. Particle size measurements were made on 29 samples using a scanning electron microscope in the backscatter mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration, Denver, CO, provided the 29 samples, which were collected at mines and processing plants in 19 states. The accumulated particle size measurements indicate that NBS 1878, minus 5-f.lm Hin-U-Sil, and minus 5-f.lm Supersil would be preferred over Silver Bond B as reference standards for most quantitative determinations by X-ray diffraction and infrared spectrometry. The respirable dust samples collected at sand plants, however, would be better served by a new reference standard having a quartz particle size distribution of approximately 2.2 um, as none of the four existing reference standards matched closely with them. Commercially available NBS 1878 and minus 5-um Hin-U-Sil CQuid be used as reference standards for 28 of the 29 samples studied in this investigation.

Jan 1, 1986

By J. B. Zadra

During the investigations of the occurrence of manganese in the western United States, the Bureau of Mines received a 100-pound sample of manganese ore from the Doyle-Smith property, Yuma County, Ariz. Laboratory tests were made to determine the amenability of this ore to standard ore-dressing methods of concentration to produce a marketable-grade product. The Doyle-Smith claims are in northern Yuma County, within 15 miles of the Artillery Peak deposit. The lot of ore used in the test work was taken from the outcrop of a large, massive, irregular bed of oxide manganese ore found on the claims.

Jan 1, 1952

By Hillary W. St. Clair

The reduction zone of the iron blast furnace is represented by a mathematical model of the chemical reactions and heat transfer that occurs between gas and solids during the deoxidation of iron oxide. The model consists of a set of equations and an algorithm whereby the equations may be solved to give the temperature and composition of gas and solids at any position in the reaction zone and at any time after a specified initial state. The model is applied to the special case in which ferric oxide is reduced by graphitic carbon and carbon monoxide produced by burning carbon in dry air. The rate of reduction, carbon consumption and maximum temperature are shown as functions of the temperature and rate of flow of the incoming reducing gas and external heat loss. The model of the reduction zone is the essential part of a general mathematical model for simulation of the iron blast furnace. The simulation model will serve as a research tool to be used in conjunction with an experimental or operating furnace. After the simulation model has been correlated with the real furnace, it is proposed that further experimentation be done mostly with the model. The real furnace will then be operated primarily to test and confirm the model.

Jan 1, 1967

By Walter Kawa

In connection with its research in producing synthetic liquid fuels from coal, the Federal Bureau of Mines studied reactions of iron and iron compounds with hydrogen and hydrogen sulfide in batch autoclaves. The Bureau hoped to gain indirect evidence regarding the chemical changes that iron catalysts undergo when they are used in the hydrogenation of coal. The information obtained may be helpful in identifying the active form or forms of iron catalysts. At 450° C., with hydrogen at hundreds of atmospheres and hydrogen sulfide at 1 or 2 atmospheres, the thermodynamically stable form of iron is ferrous sulfide in the case of the metal, magnetite, ferric oxide, ferrous sulfate, ferrous oxalate, or the chlorides of iron. However, complete conversion to ferrous sulfide was not achieved at temperatures of 400° to 500° C. for kinetic reasons. Extensive sulfiding of iron, magnetite, ferric oxide, and ferrous oxalate occurred below 400° C., and some conversion of ferrous sulfate to ferrous sulfide occurred at 400° C. In the hydrogenation of coal, ferrous sulfide is the form of iron likely to be available for heterogeneous catalysis when starting with the metal, oxide, sulfate, or oxalate.

Jan 1, 1960

By Laurel A. Powers

The Bureau of Mines process for recovering Ni and Co from low-grade domestic laterites uses a reduction roast followed by an ammonia, ammo-nium sulfate leach. This investigation examined the waste streams of the process for their potential environmental impact and focused on the laterite residue produced. The U.S. Environmental Protection Agency's extraction procedure (EP) toxicity tests and column leaching showed that leachable metal concentrations would be low enough so that the residue would not be considered a hazardous waste under present definitions. Under nonacid leaching conditions, about the same amount of metal was extracted from laterites as from their residues, and the leachates were similar to water samples from an undisturbed laterite deposit. Washing tests on the laterite residue showed that ammonia and ammonium sulfate concentrations were reduced according to equilibrium stage calculations, resulting in residues that would be acceptable for revegetation. With water washing only, the residue would not be considered a hazardous waste even though significant amounts of Ni and Co were absorbed from entrained leach solution onto the residue. Washing first with fresh leach solution and then with water prevented this absorption and thus improved the overall metal recovery.

Jan 1, 1983

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By G. R. Hopkins, E. W. COCHRANE

The number of completed petroleum refineries in the United States continued to decline in 1937 , but the total capacity to process crude oil continued to increase . These facts were ascertained in the Bureau's annual canvass of refinery capacity as of January 1 , 1938 . Several important changes were made in the census questionnaire for January 1 , 1938 . First , the basis of reckoning cracking capacity was changed from cracking stock charged to cracked gasoline produced . Although this is a definite improvement , in that it is no longer necessary to consider the yield , it is unfortunate that the data for January 1 , 1938 cannot be compared with cracking - capacity statistics since 1925. Other changes or additions included separating capacity at operating plants into that actually operating and that closed down ; collecting data on capacity added or retired during the previous year ; breaking down idle capacity according to physical status ; and separating new capacity into that built for replacement and that built to augment existing capacity . Prior to January 1 , 1938 , the total capacity of an operating plant was listed as " operating " even though some stills might have been closed down ; furthermore , the only capacity reported as being under construction was that of new plants that were being built on January 1. To make the statistics clear , the totals for the United States as of January 1 , 1938 , are given on both the old and the new bases . On January 1 , 1938 , there were 551 completed plants compared with 572 the previous year . Ten new plants were under construction on that date compared with 11 the year before . The greatest number of completed plants recorded was 632 on January 1 , 1936 ; since then , competitive conditions , particularly in the East Texas field , have been instrumental in reducing the number of small independent plants . The total crude- oil capacity of the completed refineries on January 1 , 1938 , was 4,351,151 barrels , of which 3,970 , 196 barrels ( 91 percent ) represented the capacity in actual operation and 380,955 barrels ( 9 percent ) was shut down . The " shut -down " capacity ( 199,875 barrels on the old basis ) was the lowest since pre- depression days , chiefly because numerous idle East Texas plants were removed from the list . The new method of compiling the statistics sheds considerable light on excess crudeoil capacity , which has been the subject of considerable speculation in recent years . The highest daily average crude runs to stills reached in this country was about 3,460,000 barrels in September 1937. At that time , the total crude - oil capacity was about 3,925,000 barrels . This indicates that at peak operation the excess capacity was somewhat less than

Aug 1, 1938

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the hydrogen cyanide (HCN) concentrations and smoke particle characteristics during the combustion of flexible polyurethane foams and other nitrogen-containing materials, for the development of a test parameter. The experiments were conducted in an approximately 2O-L furnace at set furnace temperatures of 250° and 1,000° C for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied as a function of time were the gaseous and aerosol HCN concentrations, the smoke particles average diameter (dg) and particle concentration (no), and the product of the smoke particle diameter and concentration (dgno). Carbon monoxide, carbon dioxide, and oxygen concentrations, sample mass weight loss, and furnace temperatures were also studied; analyses of nitrogen and cyanate content of the material were carried out. Results show that dgno correlates directly with the HCN concentrations, which depend on the nitrogen and cyanate contents of the material.

Jan 1, 2010

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

By W. W. Adams, T. D. Lawrence

The National Safety Competition , a safety contest conducted annually by the Bureau of Mines , United States Department of the Interior , to promote safety at mines and quarries , has just resulted in the award of safety trophies , known as the " Sentinels of Safety" , for 1939. Awards were made to a bituminous- coal mine in Wyoming , an anthracite mine in Pennsylvania , a metal mine in Michigan , and a nonmetallic -mineral mine in Alabama ( all being underground mines ) and to anopen-cut mine in Minnesota and a stone quarry in Michigan. The awards signify that the recipients won first place in their respective groups in an accident-prevention contest by operating during 1939 with the smallest loss of time in proportion to the total number of man-hours worked at the mine or quarry . Each of the trophy-winning companies for 1939 operated his property without a disabling injury to an employee , except at the anthracite mine , whose record , while not free of accidents , was better than that of any other mine in the anthracite group . The " Sentinels of Safety" trophy is a bronze statue of a mother and infant welcoming the father safely home after his day's work in the mine . Six trophies were provided by THE EXPLOSIVES ENGINEER magazine to be awarded annually by the Bureau of Mines . These trophies remain in the custody of the mining companies for 1 year , after which the trophies are transferred to the winners of the succeeding year's contest . A replica of the trophy is provided for permanent retention by the company surrendering the bronze trophy . In addition to the award of the safety trophies for 1939 , each man employed at a winning mine or quarry receives from the Bureau of Mines a certificate of honor in recognition of his part in helping his company to win the trophy . Companies ranking second , third , fourth , or fifth in their respective groups , and all mines and quarries whose records were free of disabling ( losttime) injuries and showed at least 30,000 man-hours worked during the contest year were awarded certificates of honorable mention . Mines and quarries that won the " Sentinels of Safety" trophies for 1939 and those that were awarded certificates of honorable mention are indicated in the following paragraphs .

Jun 1, 1940

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By D. A. Larson

This is the second in a series of Bureau of Mines reports which de-scribe experiments designed to devise an efficient, economic mechanical fragmentation technique for hard rock. The previous study described the development of the ripper cutting technique to successfully cut hard rock with 3-to 6-in-wide drag cutters. This study was conducted to test the ripper cutting technique at full scale using 9-in-wide drag cutters. The experiments were conducted with a special test device that cut shallow, 6-by 6-ft openings in 9,200-lbf/in2 compressive-strength concrete blocks. The tests showed that ripper cutting can excavate large-scale openings of the type required by the mining industry at a production rate that outperforms the conventional drill-blast technique. Moreover, the system can produce openings of various sizes and shapes, is simple to oper-ate and maintain, and produces very little dust or noise during operation. The system appears to meet all of the criteria for a successful hard-rock mining machine.

Jan 1, 1987

By J. P. Powell

The application of secondary producing methods for recovering additional oil from known fields has been recognized for many years as important to the economy of the nation. One of the most successful secondary methods is waterflooding, which conserves our natural resources by preventing premature abandoment of stripper leases and revitalizing previously abandoned areas. Waterflooding as a secondary-recovery method was introduced into the Midcontinent region in 1931, and its use as such has become widespread. As with most new methods, the most favorable fields and leases received primary attention, whereas those with viscous oil or less favorable sand characteristics were bypassed. Numerous reports3 4 5 6/ have been published giving the results of individual waterflooding projects, In this report, attention is directed to the effect of a single factor, the viscosity of the oil produced,

Jan 1, 1959

By Michael R. Yenchek

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were undertaken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 2010