Search Documents

By Ronald T. Mayerle

There are no producing or developing mines in the Rattlesnake RARE II area. Specific areas with mineral occurences are prospects for: 1) stratabound copper and silver in Belt sedimentary rocks on the northwest border of the study area; 2) base metal sulfides, in thin veins and shear zones in Belt sedimentary rock, and diabase dikes and adjacent metasedimentary rocks in the southern part of the study area; 3) barite in sedimentary rocks near Rattlesnake Creek and Sheep Mountain; 4) limestone near Rattlesnake Creek and Blue Point; and 5) silica in quartz veins near the headwaters of Rattlesnake Creek and Sanders Lake. Stone, sand and gravel suitable for construction material are in the study area; however, equal or better quality deposits are common throughout the region. The RARE II area has no known oil and gas, coal, or geothermal energy deposits.

Jan 1, 1983

By J. Koster

During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report.6/ The geology of the Marysvale region has been reviewed recently.7/ The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.

Jan 1, 1939

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

By J. A. Taylor, H. F. Yancey

"INTRODUCTION Froth flotation as applied to coal is a process for separating desirable carbonaceous material from undesirable inorganic matter. In general, the feed must be finer than one eighth inch in size. The principal use of the process in the preparation of coal appears to be in the treatment of the fine sizes produced by breakage during mining and preparation.The Bureau of Vines in Information Circular 6714 has published general information on coal flotation, summarized investigative studies of the process, and described operating plants throughout the world with their tonnage, reagent consumption and operating costs.4ACKNOWLEDGMENTSThe present study of means for depressing pyrite and reducing ash ty froth flotation was conducted at the Northwest Experiment Station of the United States Bureau of Wines in cooperation with the College of vines. University of Washington, under the general direction of A. C. Fieldner, chief engineer, Experiment Stations Division, Bureau of Wines. Grateful acknowledgment is made for suggestions and criticisms received from W. H. Coghill, supervising engineer, U.S. Bureau of Mines Mississippi Valley Experiment Station, Rolla, Mo.; J. B. Morrow, and R. E. Zimmerman, of the Pittsburgh Coal Co.; and Dean Milnor Roberts and Prof. Joseph Daniels, of the College of Mines, University of Washington.FLOTATION AND DEPRESSIONA substance will tend to float if its surface attracts a gas film more strongly than it does a liquid film when both air and liquid are competing for this attraction. On the other hand, a substance will not float if its surface attracts a liquid film more strongly than it does a gas film. All theories of depression depend upon this fact. A wetted particle of floatable size most likely will be found in the tailings after the flotation process has been completed.The crux of flotation is the selective wetting of the undesirable material that tends to float. Two general methods 5, 6, 7 of depression are in use: One combines a chemical substance with the surface to form a wettable compound, and the other employs some colloidal or ionic substance which the surface selectively adsorbs, thereby forming a wettable surface."

Jan 1, 1935

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous selective flotation tests of barite-fluorspar ores from two deposits near Marion, Ky., to determine the technical feasibility of recovering commercial grade fluorspar and barite concentrates. The lignin sulfonate-sodium fluoride method of floating the fluorspar successfully produced acid-grade fluorspar concentrates. Flotation of the barite from the fluorspar tailing using petroleum sulfonate collector yielded concentrates suitable for use in compounding oil-well drilling mud. The fluorspar and barite recoveries were about 82 and 85 percent, respectively.

Jan 1, 1963

By D. K. Steele

The domestic primary copper industry generates in excess of 600 million t of mining and mineral-processing waste annually. Most of the waste poses negligible environmental threat, but a small fraction, because of toxic or corrosive characteristics, may be subject to regulation under Subtitle C of the Resource Conservation and Recovery Act (RCRA) or other pertinent regulations. Among the wastes generated by various copper producers are flue dusts, slags, refinery-bleed solutions, and. acid-plant wastes. The U.S. Bureau of Mines (USBM) has researched methods to mitigate the environmental threat posed by copper-processing wastes while recovering valuable metals from these materials. Acid-leach processing of flue dusts has been demonstrated feasible along with sulfide treatment of liquid refinery wastes and acid-plant-bleed and gas-cleaning solutions to precipitate dissolved metals. In, addition, the feasibility of removing copper and molybdenum from slag, as well as stabilization of precipitated sulfide wastes by vitrification, have been investigated.

Jan 1, 2010

By Launa G. Mallett, Charles Vaught, Dana C. Reinke, Lisa J. Steiner, Lynn L. Rethi, Kathleen M. Kowalski-Trakofler, Jr. Brnich, William J. Wiehagen

Safety and health professionals recognize that training is a critical element of any effective safety and health program. An extensive literature survey has led the authors to conclude that we are at the beginning of a revolution in training due to changes in the demographics of the workforce, the rapid growth of technology, and the universal ascendance of the information age. Of present major concern in the mining industry is how to provide appropriate training for an aging workforce and concurrently develop training for the expected influx of new and less experienced miners as older workers retire. This report explores the key issues in the changing safety and health training area as identified by the multidisciplinary team of NIOSH researchers who conducted the literature survey. Issues include generational differences between newer mine workers and the present workforce with respect to their physical, psychological, social, and cultural characteristics; their learning styles and work expectations; and the impact of technology. Some preliminary conclusions are offered for future training needs.

Jul 1, 2004

By W. E. Wallace, P. S. Raghootama, M. S. Seehra, C. A. Hill, M. J. Keane, P. Mike

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte hemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz, kaolin, and alumina dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect cf lecithin adsorption. Dust hemolytic potential versus media pH are presented. Fourier transform infrared spectroscopy and photoacoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis.Introduction Quarts dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and' progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction. In the alveolar spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, sagas other functions, mechanically stabilises the lung from collapse by reducing the surface tension of water in the alveolar sacs.(1) This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11% in dog lavage fluid). and phospholipids (about 88%).(2) Fhosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalaitoyl lecithin (DPL).(2) Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occuring upon deposition of a particle in a pulmonary alveolus.(3)"

Jan 1, 1988

By H. R. Babitzke, H. Kato, M. D. Carver

A number of columbium and tantalum alloys were investigated to determine their suitability for use at elevated temperatures . Columbium-vanadium , tantalum-vanadium , and tantalum-hafnium alloys , and also columbium- 10 wt pct titanium alloys modified with additions of 0.1 to 2 mole pct ZrO2 , TiO2 , ZrB₂ , TiB , ZrC, or TiC were prepared and examined . Workability , tensile properties , and oxidation resistance were tested . Of the columbium alloys studied , the columbium- 12 at . pct vanadium exhibited the best properties ; it compared closely with the columbium- 10 at . pct vanadium alloy studied in a previous investigation.

Jan 1, 1964

By William J. Campbell

This Bureau of Mines report describes a study conducted to determine the relationship of mineral habit to particle size and shape characteristics for prismatic, acicular, fibrous, and asbestiform varieties of tremolite. Particle measurements were made with the petrographic microscope at X 1,250 and the scanning electron microscope at magnifications up to X 10,000. All of the varieties of tremolite, upon Wiley milling, produced a significant percentage of particles that meet the Federal regulatory criteria for counting as asbestos fibers. However, only the asbestiform variety gave milled particles that fell into a size range of >10 µm in length and <0.5 µm in width; some medical scientists consider this range significant for production of adverse health effects.

Jan 1, 1979

By Frank Pilotte

Proper design characteristics for a seismic system to locate miners during a mine disaster are considered in terms of a total system concept. Field hardware, processing equipment, operating personnel, deployment, training, and supportive R and D are necessary elements of the total system. Each of these elements is discussed and an indication given as to the requirements necessitated by each one. Hardware must be portable, rugged, and fieldworthy. Processing equipment must be simple to operate, expandable for future processing improvements, and ruggedized for field use. A small well-trained team must be available for quick response in times of emergency. Alternative deployment procedures are necessary to allow for a variety of situations including both ground and air delivery. Supportive R and D is used to support training and upgrading of the system.

Jan 1, 1974

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

By Carl Rampacek, W. A. McKinney

The feasibility of leaching calcareous and siliceous oxidized copper ores by downward percolation with dilute acid was investigated in the laboratory and in a small continuous plant operated by the Federal Bureau of Mines . The crushed ore was leached in deep columns with solutions containing 1 or 5 percent sulfuric acid to dissolve the oxidized copper . Bench - scale laboratory tests on two calcareous ores from the same deposit indicated that a maximum copper extraction , about 72 percent , could be expected from heap leaching a feed as coarse as 1 inch . Laboratory tests on a siliceous ore showed that almost 70 percent of the copper could be extracted by leaching a 1 / 4 - inch feed . The bench - scale tests were supplemented by larger continuous runs wherein the copper was recovered from the leach liquors by precipitation on detinned scrap iron . Leaching the calcareous ore for approximately 10 days recovered 62 percent of the total copper . The sulfuric acid consumption was 9.6 pounds per pound of copper recovered . Treatment of the siliceous ore recovered 62.5 percent of the total copper in a 2.5 - day leach and the acid consumption was 3.7 pounds per pound of copper recovered . Cement copper products that assayed over 71 percent copper were obtained from the leach solutions by precipitation on scrap iron . The bench - scale and continuous tests demonstrated that downward percolation leaching of the calcareous ores was technically feasible but not economically practicable because of high acid consumption by the gangue . Leaching of the siliceous ore was rapid and the acid and water requirements were nominal . The downward percolation leach procedure is simple and requires a minimum of plant equipment .

Jul 1, 1960

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

This laboratory has developed a sensitive electro-optical method to quantify the initial rate (R) and total amount.(MAX) of superoxide (SO) produced by single pulmonary alveolar macrophages (PAM). The method uses a microscope to visualize PAM in culture, and to video record the images during the time the cells produce SO. MAX and R are calculated from measurement of temporal changes in optical density in the images due to precipitated diformazan formed by the reaction of SO, produced by each PAM, with nitroblue tetrazolium present in the culture medium. To date, values of Rand MAX, measured due to adherence of PAM to the dish, have been compared to values obtained when quartz, coal mine dust (CMD), and kaolin were added to the medium (in vitro). R and MAX have also been calculated for PAM lavaged from animals exposed to quartz and CMD in the WVU Inhalation Facility. Presently, experiments are being done using serum which permits PAM to be restimulated by different dusts to help establish a dose response effect, and a means to study the effects of lung surfactant on modifying the toxicity of inhaled dusts. Long term, this methodology should provide useful insight· into establishing the role SO plays in the phagocytosis of inhaled dusts and bacteria, in PAM dysfunction, and in lung diseases such as pneumoconioses. Supported by the Department of the Interior's Mineral Institute Program administered by the Bureau of Mines through the Generic Mineral Technology Center for Respirable Dust (G1135142).

Jan 1, 1988

By J. P. Bennett

Based on previous Bureau of Mines research indicating that improved high-temperature properties could be achieved for periclase refractories through chemical additions, the Bureau investigated the properties of full-size bricks produced from chemically modified periclase refractory grains and the suitability of making such chemical additions to Mg(OH)2 slurries prior to production of the periclase grains. In full-size brick testing, strength values, both hot and cold, for the optimized bricks were superior to those for a commercial 98-wt-pct-MgO refractory. The best results were obtained for a natural magnesite with an adjusted CaO:Si02 (C:S) ratio of 3.0 and a 1.0-wt-pct addition of Zr02 and for a seawater periclase with an adjusted C:S ratio of 2.5 and a 0.5-wt-pct addition of Mn02. For samples produced from chemically modified Mg(OH)2 slurries, additions of both Mn02 and Zr02 and an increase in C:S ratios produced significant increases in hot flexural strength, similar to those resulting from chemical additions made to periclase grains. The most effective modifications were additions of Mn02 to brine-derived periclases having a C:S ratio adjusted to 3.0. These results on chemically modified magnesia refractories indicate that such material could potentially substitute for magnesiachrome refractories containing imported chromite.

Jan 1, 1984

By Gary M. Larwood

A study was conducted to determine the amount of transportation equipment required to move 1.2 billion tons of coal in 1985. The Federal Bureau of Mines has investigated a majority of the various practices associated with coal transportation and has gathered information on the regional origin-destination patterns, methods of movement, equipment stocks, rate structures, and operational capacities of the most important modes of coal haulage currently in use. Models employing this information were developed to establish the origin-destination pattern for 1985 coal shipments, estimate practical tonnage capacities for selected coal hauling rivers, develop modal shares for both unconstrained (by river capacity) and constrained cases, and present a range of coal transportation equipment requirements for given sets of constraints. Projected transportation shares for rail ranged from 63.7 to 72.3 percent, and for river, from 8.8 to 16.4 percent. Other coal transportation modes (truck, conveyor, Great Lakes, and tidewater) are expected to retain their historic shares of coal traffic. Equipment estimates were made for 1985 rail and water transportation based on 1973 average and best practice. Average practice estimates ranged from 675,000 to 710,000 hopper cars (100-ton) and 3,100 to 5,940 barges (1,400-ton equivalent). Best practice estimates ranged from 126,000 to 142,000 hopper cars and 1,750 to 3,450 barges. Full implementation of 1973 best practice by 1985 is unlikely.

Jan 1, 1976

By Foster Fraas

The objective of this research was separation of one highly conductive mineral from a second conductive mineral , a procedure which is impractical in commercial electrostatic separators using metal rolls . Such separators permit separation of nonconductive from conductive minerals . A new technique involved use of carrier electrode rolls specially prepared by anodizing and / or oxidizing at high temperatures to form suitable oxide surfaces . Specific oxides included aluminum , copper , and nickel . The significant result provided by the new surfaces was the extension of the separation range to higher conductivities , an extension in relative mineral conductivity from 10-14 mhos . The results are in accordance with the blocking- layer theory .

Jan 1, 1964

By Harold E. Marr

Energy dispersion X-ray analysis was evaluated for possible application in the secondary metals industries for the rapid analysis and identification of copper-base alloys. Laboratory investigations of standard brass and bronze samples indicate that X-ray methods are capable of separating standard alloys into 10 general classes with analytical times of less than 3 seconds per sample for clean, flat samples. A radioactive source of americium 241 with a secondary fluorescer was used as an excitation source, and a lithium-drifted silicon semiconductor detector was utilized for energy discrimination of X-rays.

Jan 1, 1974

By Alla D. Mah

The energies of combustion of two carbides of tungsten and two carbides of molybdenum were measured , and the corresponding standard heats of combustion were derived . The results are as follows : WC : AH298.15 ( combustion ) = -285,940 ± 250 cal /mole , W₂ C: AH298.15 (combustion ) = -490,660 ± 400 cal /mole , Mo₂ C : AH298.15 ( combustion) = -439,350 ± 600 cal /mole , MoC : AH298.15 ( combustion ) = -269,800 ± 1,000 cal /mole . The combustion heats were combined with the heats of formation of the corresponding metal trioxides and carbon dioxide to obtain the following heats of formation : WC : AH298.15 ( formation ) = -9.6 ± 0.4 kcal /mole , WC: AH298.15 ( formation ) = -6.3 ± 0.6 kcal /mole , Mo₂ C : AH298.15 (formation) = -11.0 ± 0.7 kcal / mole , MoC : AH298.15 (formation ) = -2.4 ± 1.0 kcal /mole . The heats of combustion and formation of MoC are tentative .

Jan 1, 1963

By David Schlain

The galvanic corrosion properties of titanium in contact with commercially pure aluminum, copper, or type 302 stainless steel in some of the common organic acids were investigated. Acids used in these experiments were 10 percent formic, acetic, lactic, citric; 1 percent oxalic and tartaric; and 9 percent oxalic. Electrode-potential measurements and several types of galvanic couple experiments were carried out. Solutions were aerated by three methods: Flow of air, flow of helium, and natural aeration. Work was done at 35° C. with couples consisting of equal areas of the 2 metals. Titanium was resistant to corrosion in most of the organic acids studied, whether alone or in contact with a dissimilar metal. However, titanium coupled with aluminum did corrode in 1- and 9-percent oxalic acid solutions. Contact with titanium usually caused aluminum to corrode by galvanic action. Copper was subject to galvanic attack in 10-percent acetic acid with a flow of air. Contact with aluminum to some solutions in which titanium is ordinarily inert and noble with respect to aluminum caused titanium to corrode

Jan 1, 1956