Search Documents

By Wesley Holmes

Concentrating, nodulizing, and smelting studies were conducted at the Albany Metallurgy Research Center of the Bureau of Mines to determine whether (1) western iron ores of the type found in the Carter Greek deposit near Dillon, Mont., could be utilized; (2) concentrates of acceptable grade with good iron recovery could be attained by wet-magnetic beneficiation; (3) nodulized concentrates could be smelted with reductants readily available in Montana; (4) iron concentrates could be smelted without prior agglomeration; and (5) high-purity iron could be produced directly from high-grade concentrates, Three small samples and two tonnage samples from the Carter Creek deposit were uniform in chemical composition, and their iron content averaged about 31 percent. They were found to be banded gneisses, and magnetite was the principal iron-bearing mineral.

Jan 1, 1962

By Fred N. Kissell

This U.S. Bureau of Mines report is a guide for the control of air contaminants during tunnel construction. Topics discussed are calculating air quantity requirements, types of ventilation systems, planning ventilation systems, control of methane gas, control of dust, control of diesel emission, ventilation to remove blasting fumes, measuring airflow, and measuring gases. This report does not provide detailed design information, but seeks to answer practical questions on air contamination issues.

Jan 1, 1995

By Robert E. Barieau

This report gives the principles of the method used by the Helium Research Center of the Bureau of Mines when solving nonlinear-regression problems and contains the mathematical equations necessary to accomplish the following objectives: the evaluation of the parameters in such a way that the sum of the weighted squares of the residuals of an experimental observable is a true minimum, regardless of the functional relationship between the variables and these parameters; and the evaluation of all variances and covariances of the parameters by means of the usual approximation of the law for the propagation of errors.

Jan 1, 1967

By William H. Pomroy

Spontaneous combustion fires involving high-sulfide-content ores are a relatively infrequent yet serious safety hazard in mining. They are also the cause of lengthy mine shutdowns because they typically occur in areas of a mine where abundant fuel material is present but which are inaccessible for fire fighting. This Bureau of Mines report describes research to design, fabricate, and test in the laboratory and field a system that warns of spontaneous combustion fires in metal mines. Overall performance of the detection system was found to be satisfactory, in that the system was capable of reliably detecting low levels of combustion products believed to indicate the preflaming stage of spontaneous combustion in metal mines. Installation of similar systems in mines with a high risk of spontaneous combustion is recommended. Principal operating problems and recommended corrective actions are also discussed.

Jan 1, 1987

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the mining laws of French Indo - China is a translation of an article published by the Department of Mines of Indo - China ; 4 and it is released subject to correction and amplification by the proper American foreign- service officers .

Mar 1, 1933

By James A. Browning

Following an unsuccessful attempt earlier in the program to develop and market a drill channelling machine, we have designed and tested a new continuous channelling method which reduces operating sound levels to below 100 db. This new method relies on a small diameter oxygen-enriched burner to produce narrow channels. Sound intensities are reduced substantially compared to conventional channel widths. They are further reduced by a water spray directed immediately above the flame. Baffles placed along the top of the channel will reduce sound levels to below 90 db. Cutting rates are greater than those of existing channelling burners with costs per unit of channel area substantially reduced for those cases where oxygen costs are reasonable.

Jan 1, 1981

By H. William Zeller

The Bureau of Mines performed laboratory research into the effects of a barium-based fuel additive (the "postflame" type) on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of types certifiable for use in underground mines. Test parameters consisted of additive concentration and engine loads, speed, and air intake restriction. DPM emissions, including condensed volatiles, were measured gravimetrically. Also measured were gaseous emissions including carbon monoxide, nitrogen oxides, and hydrocarbons. The fuel additive was effective, reducing DPM up to 75 pct, when used at a concentration of 0.09 wt pct (one-fourth of the concentration recommended by the manufacturer). The additive was most effective at the highest fuel-air ratios, reducing DPM from 400 mg/m3 for untreated fuel to 120 mg/m3. At light loads, 25 pct of full rated, no DPM reductions were measured. Based on these results, the additive is recommended for use in diesel fuel, at a concentration of 0.09 wt pct, to power underground mining equipment as long as certain conditions are met: that a beneficial DPM reduction is verified, that the minimum required quantity of additive is used, and that potential adverse effects such as increased nitrogen oxides are checked.

Jan 1, 1990

By A. W. Khair, M. Ahmad

"Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion. oxidation, or diffusion. depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been carried out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation. INTRODUCTIONContinuous miners were introduced in the 1950’s and became the major equipment in underground coal production. Now the larger production in the coal industry has increased the demand for continuous miners and their use. It is well known that serious dust problem is also introduced with the use of continuous miners, especially with recent increase in productivity. On the other hand, legal restrictions are made ·more strict by the Mine Health & Safety Administration for the respirable dust generated by the continuous miners to prevent coal workers from incidence of pneumoconiosis. The incidence of pneumoconiosis depends on dust concentration, exposure time, and physical properties of dust. Of them, dust concentration is the best parameter for the assessment of the risk of pneumoconiosis. Although a lot of research work has been done to reduce dust concentration substantially, some areas are still required further investigation to meet the strict regulations. One of the areas is about bit wear and dust generation. In this area, the principles of bit wear and effect of bit wear on dust generation are major concerns."

Mar 1, 1992

By W. I. Nelson

This paper which describes the milling practice of the Engels Copper Mining Co., is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is made of the assistance rendered by J. Casagrande, mill foreman of the Engels concentrator, in collecting much of the data presented in this paper.

Jan 1, 1932

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By Alan R. Buehler

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 256,430-acre Alvord Desert and part of the 22,240-acre East Alvord Wilderness Study Area (OR-002-074 and OR-002-073A, respectively), in order to evaluate their identified mineral resources. The study areas are located in Harney and Malheur Counties, OR, about 25 mi northeast of the small village of Fields. There are no mines, prospects, or identified mineral resources inside the study areas. Basalt flows within the study areas contain chalcedony-lined vugs and banded agate which may be of interest to rock hounds. An ignimbrite flow contains perlitic material, but crystalline contaminants make it unsuitable for commercial uses. Lacustrine (lake) sediments contain diatomite and clays, and evaporite crusts contain boron too low grade to profitably mine. Small quantities of common opal and petrified wood occur which might be of possible interest to rock hounds. Some of the petrified wood is black, free of fractures, and polishes well; it may be suitable as backing material for soft, thin, and brittle gemstones, such as precious opal. The lacustrine sediments also contain black, fetid layers which have above background, but economically insignificant concentrations of zinc, cobalt, nickel, barium, iron, manganese, aluminum, and potassium. Large quantities of fine-grained dune sands within the study areas are too far from markets for economic consideration. Ephemeral streams in the study areas contain small amounts of placer gold of no economic interest. The western portions of both study areas are reported to have moderate favorability for occurrences of natural gas, and both study areas are reported to have high favorability for the occurrence of geothermal resources. As of December 1986, oil and gas leases covered 3,100 acres in the study areas.

Jan 1, 1987

By D. Bienstock

A high-B.t.u, gas can be synthesized by the catalytic methanation of a mixture of 2.5 to 3 parts of hydrogen to 1 part of carbon monoxide, obtained in the gasification of coal, using a steel catalyst followed by Raney nickel in a hot-gas-recycle system. Conversion of 99 percent of the H2+CO yields a fuel gas with a heating value of 983 to 1130 B.t.u. per cubic foot containing 78 to 96 percent methane, no carbon monoxide, and very small amounts of unsaturated hydrocarbons. With the steel catalyst alone, conversions were 85 to 90 percent, giving a fuel gas of 810 to 868 B.t.u, per cubic foot, or 847 to 975 B.t.u. on a C02-free basis. INTRODUCTION In 1948 the U.S, marketed production of natural gas was 5.15 trillion cubic feet; by 1958 it had reached 11.0 trillion cubic feet, a rate of growth of 8 percent annually. 4 5 Although demand is expected to increase less rapidly, by 1966 it may reach 16 trillion cubic feet, based on an estimated 4.7 percent annual increase.6

Jan 1, 1961

By Wilbur I. Duvall, Thomas C. Atchison, Joseph M. Pugliese

Short cylindrical charges were detonated in drill holes in rock to determine the effect that decoupling ( defined as the ratio of the radius of the hole to the radius of the charge ) has on the strain - generating abilities of explosions in rock . The amplitude and period of the strain pulses produced in the rock were studied as a function of distance , size of charge , and decoupling . The main results of these studies were that , for a given distance and size of charge , the amplitude of the strain pulse decreases as decoupling increases and the period of the strain pulse decreases at first and then increases as decoupling increases . A simplified theory of decoupling is presented that satisfactorily explains the experimental results . The information presented makes it possible to predict the effect of decoupling on explosiongenerated strain pulses in rock and thus helps the explosives user evaluate the effect of decoupling on his blasting .

Jan 1, 1964

By Donald P. Blasko

The first well that produced commercial quantities of oil in the Cook Inlet Basin of Alaska was completed in 1957. Since that time oil production in the basin has increased rapidly and by the end of 1969 had reached an annual rate of 74 million barrels. Five major oilfields had been developed, and two additional discoveries awaited development. Estimated amounts of recoverable oil by primary and secondary recovery methods total 2.7 billion barrels, or 36 percent of the estimated oil originally in place. Repressurization by injecting gas or water in formations containing undersaturated oil has significantly increased the volume of recoverable oil. All production has been from formations of the Tertiary age; that much of it is from depths of 10,000 feet or more is unusual for Tertiary formations. The oils are low in sulfur and contain low to moderate amounts of asphalt.

Jan 1, 1972

By R. K. Koch

The Bureau of Mines produced several series of titanium castings in order to investigate the feasibility of producing commercial-grade titanium castings in bentonite-bonded olivine or zircon sand molds. The use of these molds for titanium casting was investigated as a possible alternative to the industrially used rammed graphite process. Parameters investigated were mold mixtures, mulling, gating, venting, drying, and mold washing. The investigators found that castings with superior ductility and fatigue life, compared with rammed graphite castings, could be made by fume-free pro-cesses in molds bonded by western bentonite, using either olivine or zircon sand. Zircon molds were satisfactory for both light-and heavy-sectioned castings. However, olivine molds were suitable only for light-sectioned castings because the mold-metal reaction became excessive during the pouring of heavy-sectioned castings.

Jan 1, 1981

By Ernesto Villaescusa, Andres Brzovic

Rock masses of the primary copper ore at the El Teniente Mine are very competent and massive. The rock mass contains almost no open discontinuities. Nevertheless, there is a high frequency network of small discontinuities coupled with widely spaced faults. A data collection campaign designed to characterize the rock structure was recently implemented. The results show that conventional analysis in terms of discontinuity frequency does not predict differences between two studied sectors. However, when an empirical definition of a weak discontinuity is applied, appreciable differences between the two sectors appear in terms of discontinuity frequency and predicted in situ block size distributions. These differences are in accordance with actual observations at the mine site. Due to the geological features of the primary copper ore, rock mass classification schemes cannot be readily applied to characterize these rock masses.

Jan 5, 2007

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974

By Edward L. McHugh

Mineral resources in the Silver Creek study area of the Nez Perce National Forest. Idaho, were investigated during the summer Of 1989. The study area includes the 36,100-acre Silver Creek-Pilot Knob RARE II area (No. 1-849) on the north side of the South Fork Clearwater River, about 11 miles west of Elk City, 10. Mines in and near the study area in the Tenmile and Newsome mining districts produced about 100.000 02 of gold, mostly from placers. Gold production had an historic value estimated at 52 million, equivalent to nearly $40 million at today's prices. Lode mines produced about 19,000 oz of gold, along with smaller amounts of silver, copper, lead, and zinc. Of 34 mines and prospects examined, ten lode properties are considered to be significant by virtue of their past development or production and the presence of possibly ore-grade mineralization. There are no identified mineral resources in the study area; however, samples that contained gold and anomalous arsenic delineate a three-mile-long area from the Sentinel mine, north to the Blue Quartz prospect where exploration might disclose resources. One mining company is conducting geophysical studies and drilling within the delineated area. In addition, six placer sites may contain enough gold to be of possible interest for future exploration and development.

Jan 1, 1991

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982