Search Documents

By Virgil J. Stachura

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine that resulted in smoother highwalls. The 17; were smoother due to reduced overbreak and inherently safer A, to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delays, which changed the effective delay pattern geometry and the direction of burden movement. The blast delays in the highwall holes were 50 to 100 ms longer than the mine's nominal design pattern (flat V, 17- by 42-ms surface delays, 200-ms in-the-hole delay). The burden movement was effectively changed from a 45* angle to 90* with respect to the highwall. The results of the blast delay changes were evaluated using terrestrial photogrammetry to generate vertical profiles at regular intervals. This evaluation showed that delay changes produced generally smoother vertical profiles.

Jan 1, 1984

By Farrel W. Lytle

An X-ray emission spectrographic method of analysis is presented for determining rare-earth elements in fractions obtained from bastnaesite ore. The method includes determination of yttrium, thorium, lanthanum, and the rare-earth elements in various complex mixtures. The analysis technique is based upon comparing the samples with synthetic standards approximating the composition of the samples. Working curves are plotted on an absolute-intensity basis, with no correction for back-ground. Examples of working curves and the analyses of typical rare-earth concentrates are included. The selection of spectral lines for the various sample matrices is discussed. A special technique is used for samples in which rapid hydration and carbonation occurred. By analyzing synthetic samples of known composition, the accuracy of the method was determined. The average error of analysis was about 3 percent of the amount present in the range from 5 to 100 percent and about 7 percent in the 0.2-to 5-percent range. A maximum of about 40 samples per day may be analyzed for 7 elements each.

Jan 1, 1957

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Clay, Gilmer, and Lewis Counties, W. Va. In 1966, almost 1.3 million tons of coal was mined in these counties, of which more than one-half was from the Pittsburgh coalbed. Washability analyses were made of 16 coalbed samples. Of these, only 11 samples could be upgraded to metallurgical quality. For steam or power generation five of the coals were of low sulfur content as received. The remaining samples were generally of medium sulfur content even after upgrading.

Jan 1, 1969

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill and blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By Gene Asai

Properties obtained for columbium carbide-carbon castings ranging in car-bon content from 12 to 17 weight-percent were compared with those of hot-pressed composites of similar composition. The properties were oxidation resistance in static air between 500° and 700° C, linear thermal expansion between 20° and 2,400° C, electrical resistivity between 20° and 1,500° C; microhardness between 20° and 1,500° C, and modulus of rupture between 1,300° and 1,800° C. CbC-C castings differed markedly from hot-pressed material with respect to microstructure, electrical resistivity, and modulus of rupture, but behaved quite similarly with respect to oxidation resistance, thermal expansion, and hot hardness. In oxidation resistance, thermal expansion, and hot hardness both materials were independent of carbon content. Both castings and hot-pressed composites oxidize rapidly in air above 600° C, have thermal expansion coefficients very similar to columbium metal, and the logarithm of the hardness decreases linearly with increasing temperature. The microstructures of hot-pressed composites contained varying amounts of graphite in a CbC matrix but did not contain significant amounts of a eutectic structure present in all castings, nor did they contain graphite needles which were present in the hypereutectic castings. The higher electrical resistivity of hypereutectic castings over hypereutectic hot pressings was attributed to the presence of highly oriented graphite needles in the castings. The modulus of rupture of castings was 1-1/2 to 2 times that of hot-pressed composites. Both materials displayed bend ductility above 1,800° C.

Jan 1, 1971

By Irving Hartmann, F. P. Christofel, John Nagy, E. B. McGibbeny

"INTRODUCTION When permissible explosives are used in c procedure recommended by the Bureau of Mines 5/ they are relatively safe, and, no mine explosions are known to have resulted from this type of blasting. However, unsafe blasting practices - the use of nonpermissible explosives or the improper use of permissible explosives - have caused many serious disasters. In fact, such unsafe practices constitute the third most important cause (exceeded only by electricity and the use of open lights and smoking) of coal-mine explosions in the United States. During 1929-1947, inclusive, 81 explosions, resulting in 475 fatalities, were ascribed to unsafe blasting. 6/The hazards of black powder, dynamite, and other nonpermissible explosives in coal mines have been recognized for many years, and attention has been called to this in numerous Bureau of Mines publications. Not only can these explosives ignite flammable gas-air mixtures readily, but they can also ignite coal dust, as has been illustrated repeatedly in tests and at educational public demonstrations at Bruceton and elsewhere. 7/Research in the Experimental coal mine 8/ of the Bureau of Mines at Bruceton, Pa., and unfortunate experience in commercial mines have proved beyond doubt that improper use of explosives that have passed the official permissibility tests can cause as explosions. In limited tests with a fey American permissibles at Bruceton, and in more, extensive tests with permitted explosives at the Polish experiment station, 9/ explosive charges were fired from steel cannon and freely suspended in coal-dust clouds. In these experiments coal dust was ignited under some conditions. However, it has never been definitely established whether permissible explosives can initiate coal-dust explosions when fired in a coal seam. It is true that a few mine explosions were strongly suspected to have resulted from ignition of coal dust by misuse of permissibles, but in each case other complicating factors introduced some doubt in the minds of the investigators. Full knowledge of the problem is important, because coal dust is present in most blasting operations in coal."

Apr 1, 1952

By Wilbur I. Duvall

Twelve millisecond delayed blasts in four limestone quarries in Iowa were instrumented with arrays of vertical velocity gages to determine if the direction of propagation through the rock or the method of initiation of the blast had any effect upon the level of vibration. Two gage arrays approximately 90° apart were used to test the effect of direction of propagation. The vibrations from blasts initiated by three methods were recorded. Vibration records from these tests were analyzed for peak particle velocity as a function of distance from the blast. The data are shown to fit a power Law equation. Direction of propagation is shown to affect the value of the exponent n. The effect of charge size per delay interval on the level of vibration is removed from the data by scaling the travel distance by the square root of the charge weight per delay period. The method of initiating the blasts is shown to have a strong effect upon the level of vibration and the spread in the data from one shot to another.

Jan 1, 1963

By L. A. Haas

The feasibility of removing sulfur dioxide by carbon monoxide reduction in a fixed-bed catalytic reactor was investigated by the Bureau of Mines. The reduction rate of sulfur dioxide with carbon monoxide was significantly dependent upon the iron and alumina content of the mixed catalyst. Maximum catalytic activity was obtained with about 40 percent iron-alumina mixture with a nominal gas mixture of 10 percent carbon monoxide, 5 percent sulfur dioxide, and the balance nitrogen. The synergistic effect of this catalyst mixture was explained by a dual reaction site mechanism, with both iron and alumina augmenting their specific sites at their interparticle contacts. The catalytic activity also increased with decreasing catalyst pellet size. With O.7-mm pellets, the entire pellet appeared to be catalytically active in a 2-gram catalyst bed. The apparent activation energy of the reaction was 18.3 kcal per mole in the temperature range of 350° to 600° C. Carbonyl sulfide (COS) was produced by the interaction of carbon monoxide and sulfur. The amount decreased with decreasing CO concentration. The ratio of COS formed per SO2 removed reached a maximum at about 400° C. The reaction rate appeared to be independent of S02 concentration in the range of 0.2 to 16 percent. The rate, however, increased directly with the CO concentration in the range of 5 to 20 percent. The presence of CO2 (<15 percent) had no appreciable effect on the rate. However, not over 0.5 percent oxygen could be tolerated. This method appears feasible for removing S02 from waste gas if the oxygen is removed prior to the catalytic S02 reduction process.

Jan 1, 1971

By Maria I. De Rosa

Combustible materials, when burned, produce toxic gases and smoke, which may vary dramatically from one material to another, with resultant different total toxicity and smoke obscuration levels. This U.S. Bureau of Mines report presents smoke property data acquired for a variety of mine combustibles and shows that there exists a correlation between the smoke properties, the relative toxicity, and the smoke obscuration levels of those combustibles tested. These correlations can be used to devise simple, standard tests for determining the toxic and smoke obscuration hazards of mine materials during fire.

Jan 1, 1989

By E. L. Litchfield

Spark ignition of combustible-gas mixtures is a relatively old subject of investigation and has been treated both experimentally and analytically by many people. Elements of static and current electricity are almost always present in mining and industrial operations, and the spark can be an extremely efficient source of ignition. Thus the practical interest of such problems as the "intrinsic safety" of electrical apparatus is obvious. Ignition and quenching phenomena are the primary laboratory representatives of combustion phenomena that are dynamically nonsteady, and such nonsteady phenomena playa considerable part both in industrial processes and in safety matters, although they are of less immediate practical interest. Considerable effort has been expended by the Federal Bureau of Mines in investigations of spark ignition.5 6 7 8/ Primarily, this work has established the significance of several of the parameters involved. Although the

Jan 1, 1959

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By C. H. Elder

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau&apos;s long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand-stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By A. D. Hahn

This report describes and gives the results of an examination by the Federal Bureau of Mines of ilmenite-bearing placer sand deposits in the 24-mile long valley of Otter Creek, Kiowa and Tillman Counties, Okla. Drilling and sampling was completed in three periods between October 1956 and September 1957. Mineralogic studies and mineral-dressing tests on recovery of ilmenite and other heavy minerals from composited samples of the sands were made in Bureau of Mines laboratories at Rolla, Mo., in 1957 and early 1958. Otter Creek rises in and drains the southwestern extremity of the Wichita Mountains, which are represented locally by knolls and ridges of gabbro and granite surrounded by plains floored with flat-lying Permian red beds. The valley fill consists of a basal sand-clay component, derived from weathering of the igneous rocks, and an overlying silt-clay alluvium. Ilmenite is present in significant quantity and recoverable grain size only in the basal sand-clay.

Jan 1, 1960

By W. E. Dennis

"INTRODUCTION The strategic importance of zinc warranted investigation of the Silver Eagle zinc prospect, which was first examined by an engineer 3/ of the Bureau of Mines in January 1943.From October 12, 1943, to March 16, 1944, the Bureau explored the deposit by trenching, core drilling, and sampling to establish the amount and grade of ore and to test for the presence of sulfide-ore minerals at depth.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946

By Dennis A. Hansen

As part of a U.S. Bureau of Mines program to develop a more continuous titanium metal extraction process that uses domestic resources, a study was made to determine the extraction of titanium (Ti) and iron (Fe) from New York rock ilmenite using fluosilicic acid (H2SiF6). The effects of leach temperature, acid concentration, and particle size were investigated for the rate at which Ti and Fe are extracted from the ilmenite. Within the leach time studied, the extraction data fit a shrinking-core model; the rate-controlling step was diffusion of H2SiF6 through an ash layer resulting from a heterogeneous leaching reaction. The rate is linearly dependent on the H2SiF6 concentration and is inversely proportional to the square of the particle diameter. Using 2.6M H2SiF6 at 85°C, 49% of the Ti and 53% of the Fe in 44-to 74-µm New York rock ilmenite were extracted in 3 h.

Jan 1, 2010

By E. C. Perkins

Preliminary experiments are reported utilizing bacteria to leach manganese from a variety of domestic low grade manganiferous materials. In two large leaches manganese extraction ranged from 71.7 to 92.5 percent, and the products analyzed over 48 percent manganese. Nutrient requirements and leaching time experiments were made. The mechanism of leaching is not understood, but is different than the mechanism encountered in the microorganism accelerated leaching of copper in the presence of sulfide minerals.

Jan 1, 1962

By Alla D. Mah

No experimental heat-of-formation value has been reported in the literature for cerium sesquioxide. The heat of formation of bismuth sesquioxide has not been determined in recent years, and the older value was subject to large uncertainty. Accordingly, the heats of combustion of cerium sesquioxide and bismuth metal were measured by the Federal Bureau of Mines. The heats of formation were: ?H°298.15 = -427.01 ± 0.70 kcal. /mole for cerium sesquioxide and ?H°298.15 = -137.16 ± 0.30 kcal./mole for bismuth sesquioxide. The free energy of formation was estimated for cerium sesquioxide and accurately calculated for bismuth sesquioxide. The data were compared with values in the literature.

Jan 1, 1961