Search Documents

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the eleventh. The-data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each halt township is followed by a description of each deposit developed in that halt township. The 14 halt-township maps and 77 detail maps of the bauxite deposits in this series at reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained tram the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion of that area.

Jan 1, 1948

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By T. L. Joseph

The size and accessibility of the Minnesota manganiferous iron ore deposits make them attractive as a potential source of erromanganese, which is essential in the production of steel. For several years the Bureau of Mines has been conducting experiments to determine the feasibility of producing ferromanganese from these ores by a three-step process which involves (1) the smelting of the ores in the blast furnaoe to produce a high-phosphorus spiegel; (2) the treatment of the spiegel produced from step 1 in an electric or open-hearth furnace to separate the manganese from the phosphorus and the iron; and 3) the smelting of the high-manganese slag from step 2 to produce forromanganese. The details of the first two steps of the process and the results of tests with the experimental furnaces Lave been given in previous reports.5 The m$ or part of the experimental work on the second step has been conducted in a half-ton open-hearth furnace. Some preliminary tests showed, however, that the electric furnace has some distinct advantages over the open hearth for producing, from high-phosphorus spiegel, a slag containing from 45 to 55 per cent manganese and phosphorus and iron in amounts required for ferro-grade ore. The electric furnace tests described in this paper were made to get more information as to the possibilities of the electric furnace in connection with this problem and to study the fluxing effect of alumina on high-manganese slags. Herty, Conley, and Royer have reported' results of laboratory tests which showed that slags containing from 60 to 75 per cent MnO, from 8 to 10 per cent S102, and small amounts of CaO MgO, and FeO, were sufficiently fluid at 1,450° to 1,550° C. to pour readily if 12 to 14 per cent alumina was present. With a normal A1203 content resulting from the A1203 in the

Jan 1, 1931

By G. L. Gates

The Bureau of Mines studied the scales formed in producing wells in the Wilmington field, California. The scales were primarily barium sulfate and resulted from the mixing of injected sea water and formation waters; there was excess sulfate in the injection water and the formation waters contained appreciable barium. After breakthrough, the produced brines were supersaturated with barium sulfate. Laboratory tests indicated that barium sulfate precipitated quickly When the supersaturated brines were agitated with crystals of barium sulfate and fairly rapidly when more sulfate solution was added. Precipitation occurred slowly on standing or under nonturbulent conditions. Both the apparent and equilibrium solubilities of barium sulfate in these brines were determined and compared with equilibrium solubilities in distilled water and sodium chloride solutions.

Jan 1, 1965

By John P. Powell

A comprehensive study of the effects of hydraulically fracturing water-flood wells in Oklahoma has been made by the Federal Bureau of Mines. This report presents results of that study and an analysis of some of the factors governing the results of fracture treatment on waterflood properties. Originally, hydraulic fracturing was used to stimulate oil production from old wells producing by primary methods, and its application to water-flooding was regarded with skepticism by most producers. However, since 1953 the number of fracture treatments of both oil and input wells in waterfloods has increased steadily. Hydraulic-fracture treatments in waterfloods have generally been successful in stimulating production from oil wells and increasing the rate of injection into input wells. Hydraulic fracturing has enabled several producers to turn probable failures into economically successful projects.

Jan 1, 1961

By O. H. Metzger

This is one of a series of papers being published by the Bureau of Mines on mining areas and districts in the Western states. It describes mining and milling practices in the vicinity of Wickenburg in Maricopa and Yavapai Counties, Ariz. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of the operators of the mines visited. Reports of geologists and engineers who previously visited the area were drawn upon freely. Individual acknowledgments are made in the text.

Jan 1, 1938

By C. B. Daellenbach

A prototype particulate size analyzer system was developed that would rapidly determine size distributions of homogeneous and two-mineral materials in the 74-micrometer (200-mesh) to 7-micrometer size range. The system sizes particles in a series of hydrocyclone elutriation steps and senses the weight of the five sized fractions by nuclear attenuation techniques. Size distribution of materials was determined from experimentally developed mathematical relationships that existed between particulate weight and the measured transmittance of gamma rays from an Americium-241 source. In the developmental phases, size distributions of three minerals (quartz, magnetite, and hematite) and a laboratory prepared two-mineral mixture of quartz and magnetite were accurately determined by the prototype system. In later stages of the investigation, semiconcentrates, an intermediate magnetic product from a taconite plant, were evaluated. Using 25-gram feed samples of this industrial material, the analyzer system was found to predict weight percentages for individual size fractions with an accuracy of ±0.85 percent or better at a 95-percent confidence level.

Jan 1, 1974

By T. L. Joseph

The size and accessibility of the Minnesota manganiferous iron ore deposits make them attractive as a potential source of ferromanganese, which is essential in the production of steel. For several years the Bureau of Mines has been conducting experiments to determine the feasibility of producing ferromanganese from these ores by a three-step process which involves (1) the smelting of the ores in the blast furnace to produce a high-phosphorus spiegel; (2) the treatment of the spiegel produced from step 1 in an electric or open-hearth furnace to separate the manganese from the phosphorus and the iron; and 3) the smelting of the high-manganese slag from step 2 to produce ferromanganese. The details of the first two steps of the process and the results of tests with the experimental furnaces have been given in previous reports.

Jan 1, 1931

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By Robert H. Ridgway

This circular outlines salient facts regarding the manganese-ore industry in the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and public by giving further information in response to individual inquiries. The Bureau will welcome comments, criticisms, and contributions of data that may assist in making later additions of this circular more accurate, or in developing more fully its mineral files pertaining to manganese. In reporting the production of manganese-bearing ores in the United States the following classification has been adopted by the Bureau of Mines: (1) Metallurgical-grade ores, under which have been classified manganese ores containing 35 percent or more of manganese used in the manufacture of iron and steel, ferruginous manganese ore containing 10 to 35 percent of manganese, manganiferous iron ore containing 5 to 10 percent of manganese, and manganiferous zinc residuum; (2) battery ore; (3) fluxing ores, under which are classified ores that may contain a few ounces of silver and are rich enough in manganese to make them valuable chiefly for fluxing purposes in nonferrous smelters; and (4) miscellaneous ores, under which are classified the ores shipped to brick manufacturers, glass makers, and manufacturers of manganese chemicals.

Jan 1, 1933

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"Stoppings in coal mines serve, important and. vital functions, such as coursing the ventilating current, sealing off abandoned or dangerous workings, sealing fire areas, and separating mines at boundaries. Stoppings may hold back water, but normally that is not their function; their design is, or should be very different from that of a hydraulic dap which is designed to a definite load, often a very heavy one, from one direction over an indefinitely long period. Hence, a dam usually requires an arched structure to resist hydraulic pressure, and it must be massive to meet vertical stresses due to heavy ground pressure.Stoppings are designed primarily to resist a pressure applied laterally through air or gases. Their strength cannot be stated without specifying the direction of applied load. A stopping may be placed in stress by proof pressure subsequent to erection, through extraction of pillars in the vicinity which may act direct, or by squeezing the ribs or heaving the floor. These forces act more or less parallel to the faces of the stopping and may be very great but measures must be taken suitable to each case, and it is impossible to allow for these in general specifications other than to call for normally good construction. A stopping is principally designed to resist the action of forces at right angles to its face, such as the shocks of blasting, the pressure of gas from instantaneous violent out bursts such as have occurred in certain British Columbia coal mines, sudden compression of the air by great falls of roof in closed spaces, and at time pressures that accompany an explosion of either fire damp or coal dust or both. This paper deals with the tests of pressures of explosions only."

Sep 1, 1930

By M. F. Dunn

A handbook to provide a quick reference guide for selecting and using jet fans in a variety of conditions was prepared. The document is intended for use by front-line supervision, ventilation engineers, and mine planners. Included are discussions of jet fan characteristics, selection and use critieria, and do's and don't's for easier operation, safety, and performance. The handbook is based on research at three underground metal/nonmetal mines having cross-sectional areas of 900 to 2,000 ft2.

Jan 1, 1983

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

By Glenn C. Reed

"Preliminary examination of the Glass Buttes mercury deposits, Lake County, Oregon, was made in August 1945 at the request of W. S. Lazier, present lessee of the deposit.Most of the prospect openings in the area were inspected. The more significant workings were sampled and napped in detail. This report presents the data obtained from the investigation to date.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. noon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. P. S. Dean, assistant director.Special acknowledgment is due to S. H. Lorain, chief, Albany Division, Mining Branch and to S. R. Zimmerley, chief, Salt Lake City, Utah, Metallurgical Division, for analyses of the ores.The presence of quicksilver in the Glass Buttes district has been known since about 1930. The area immediately north of Middle Butte has been superficially prospected by numerous test pits, trenches, shafts, and short adits, which revealed a number of opalized zones. Many of these opalized zones contain weak to strong concentrations of cinnabar. The area has not boon explored thoroughly; no mercury has been produced from any of its deposits.A block of 48 full-size claims has been located to cover a large part of the area in sections 34 and 3, Tps. 23 and 24 S.,R. 23 E.,W.M. These claims, held by, location are owned by H. S. Miller, lumberman of Bend, Ore. W. S. Lazier, 10N. W. 20th Avenue, Portland, Ore., currently controls the property under,a nominal leasing agreement. J. W. McDaniel, 44 Lake Place, Bend, Ore., has done much of the underground and surface exploration on the property.The Glass Buttes district is an area of low relief in the Deschutes River drainage system near the northeast corner of Lake County, Ore. (See fig. 1.) The arid climate is marked by extremes of winter and summer temperature. Water for cane use is not available in the immediate area. Well water, however, can be obtained in limited supply on ranch property 5 miles to the south."

Aug 1, 1946

By J. P. Bennett

The Bureau of Mines investigated the dimensional changes of ceramic materials exposed to acid environments to evaluate construction materials for emerging technology in chemical and metallurgical processes. Six commercial ceramic materials (two red shale, two fireclay, one silica, and one silicon carbide (SiC» were exposed to H20, 20 and 30 wt pct HCl, 40 and 60 wt pct HN03, and 10 and 50 wt pct H2S04 at temperatures from 50° to 90° C for 300 days. Linear expansions ranged from a low of -0.02 pct for the silica to a high of 0.45 pct for the red shale. A general ranking of the volume expansion of the materials tested, (from high to low), is as follows: high-porosity red shale A and fireclay B » low-porosity red shale B and fireclay A > silicon carbide and silica. A general ranking (largest to smallest) of the effect of exposure environments is HCl > H2S04, HN03 > H20. An autoclave test method was evaluated. Data obtained from 8-to 24-h exposures were compared with data obtained from the 300-day exposures. The relative expansion trends were similar, indicating that this method could be used as an accelerated test.

Jan 1, 1988

By A. B. Needham

Graphite is a raw .material of considerable importance in both waxy and peace. Two types of graphite, classified according to particle size as flake and fines, are used, but the former is in much greater demand. The principal wartime use of graphite is in the manufacture of crucibles for melting brass and special alloys of copper and steel. Other uses in both peace and war are as lubricants, for foundry facings, and in paints, electrodes, batteries, motor and generator brushes, and a variety of other commodities. . This paper describes the operations of the Southwestern Graphite Co. of Los Angeles, Calif., which produces both flake and fine graphite from a property in Burnet County, Tex.

Jan 1, 1946

By R. V. Higgins, H. C. Miller

"INTRODUCTION The development of methods for determining the total quantity of crude oil that a given pool could be expected to produce in the future and the well-spacing and drilling programs most likely to result in the recovery of the maximum quantity of oil at the minimum cost became problems of acute concern to American oil producers and petroleum engineers during the second decade of the twentieth century, The United States faced what seemed at that time to be a serious shortage of petroleum, and it appeared that the constantly increasing demand for petroleum and its products could not be adequately supplied. Undrilled prospective acreage, which until then had been plentiful, seemed to be getting scarcer, competition was increasing, the margin of profit to the producer was shrinking, and the need for developing constructive policies of conservation appeared paramount. As a result of physical and economic changes then taking place within the petroleum industry prompted by the seemingly uncertain future, accurate knowledge pertaining to the probable future production of oil wells and of oil lands especially was needed and greatly desired. Furthermore, the need for obtaining the maximum quantity of oil from known fields caused technical information - which up to that time had not been deemed essential to the successful and profitable operation of oil lands - to be sought eagerly. The need for technical information, such as methods for determining future reserves of oil and the rate at which the oil could be obtained under a specific program of drilling, was emphasized further with the passage of the Revenue Act of 1918, and oil producers with enough income to place them in the taxable class were compelled, for the first time, to report their taxable income 4/ to the Treasury Department."

Nov 1, 1939

By F. V. Meriwether

The Bureau of Mines, in cooperation with the Federal, State, and local health services, and the mining companies, and miners? organizations, has for several years been carrying on sanitary surveys of mining districts in various states, with the purpose of collecting information on good and poor practices in mine sanitation, construction of approved wash-houses and change houses, the measures being taken to combat preventable diseases, the essential features of good houses for mining towns, and other conditions affecting the health and efficiency of miners and their families. The knowledge thus gained is disseminated for the common benefit of the mining industry. The sanitary conditions in the coal-mining districts of Alabama, as found by a recent survey made by the writer, are presented in this report. In addition to the towns on which this report is chiefly based, at least twice as many were visited where no details :were taken, but their general conditions are taken into consideration in summing conditions in the coal districts.

Jan 1, 1926

By E. J. Schneider

In view of the current interest in the constituents of low-temperature tar, the Synthesis of three known xylenols and their hydroxyacetic acid derivatives has been undertaken by the U. S. Bureau of Mines. One of these xylenols, the 1,3,2 derivative first reported by Steinkopf and Höpner,4 has been described by Brown and Branting.5 The other two derivatives, the 1,3,5 first reported by Schütz6 and the 1,2,3 reported by Steinkopf and Höpner, have now been studied in greater detail. In the present work the synthesis of 1,2,3-xylenol and 1,3,5-xylenol was repeated, with some improvements in the former. The hydroxyacetic acid derivatives were also prepared, and it was found that while the melting point of the 1,2,3 derivative agreed with that of Steinkopf and Höpner. that of the 1,3,5 derivative was found to be 111° instead of 85 to 86° as reported by Schütz, by Steinkopf, and later by Bruckner. The discrepancy between the melting-point figures is doubtless due to differences in the purity of the xylenols used in the synthesis of the acids. Schütz obtained his 1,3,5 acid by recrystallizing an impure sample obtained from a mixture of xylenols. The difficulty of obtaining a pure acid by starting with a mixture is demonstrated by Bruckner, who despite painstaking efforts was unable to obtain the pure 162.5° melting 1,2,4 isomer from a mixture that persistently melted at 138° C. Steinkopf did not repeat Schütz's work but merely used the latter's figures in compiling a table. Bruckner, on the other hand. apparently also made the acid (by an improved method), and it is difficult to explain his checking Schütz's figure, unless it is that he, too used a symmetrical xylenol obtained from a tar and not prepared synthetically, as was the one reported in this paper.

Jan 1, 1929