Search Documents

By Gene Asai

The Bureau of Mines investigated the caustic extraction of alumina and soda from retorted dawsonite-bearing oil shale, as part of a program to devise technology for treating alternative domestic sources of alumina for the production of aluminum metal. Colorado oil shale yielding 13 pct oil (35 gal/ton) and containing 12 wt-pct dawsonite (representing about 4 pct extractable alumina) was retorted to obtain oil-free (spent) shale Spent shale was leached with dilute NaOH to determine the effect of particle size, retorting temperature, leaching variables, and storage conditions on extraction of alumina and soda and dissolution of impurities. Maximum alumina and soda extractions were obtained by promptly leaching minus 28-mesh spent shale, obtained by retorting raw shale at about 5000 C, with 0.5N NaOH. Under these conditions, dissolution of impurities such as Ca, Fe, Ti, and P was low. Leaching tests were made on spent shale stored for periods of up to 30 days at 0° to 42° C and at 0 to 100 pct relative humidity (RH). These tests indicated that significant reductions in alumina extraction would occur if spent shale were stored in ambient Colorado air under naturally fluctuating temperature and humidity.

Jan 1, 1983

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,421 samples, representing the products of 131 companies. The samples were collected during June, July, and August, 1953. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1954

By R. V. Higgins

The Bureau of Mines investigated the use of electronic computers for obtaining more information about relative permeabilities of reservoir rock to oil and water. It was found that there are many possible combinations of relative permeability curves that will result in virtually the same recovery versus injection) but they require different times and rates to recover the oil even with different mobility ratios. Permeability curves obtained by the use of non-viscous oil and employed for calculating the waterfloods of viscous oils can lead to serious inaccuracies. For viscous oils) the wettability characteristics in the middle portion of the permeability curve affect recovery nearly as much as other portions of the curve; this) however) is not true for non-viscous oils in water-wet reservoir rock.

Jan 1, 1967

By B. E. Blair

"This report presents the physical properties and related geological and petrographic data of some 84 rock types from operating mines, quarries, or blasting research test sites. These fundamental rock data were collected as a quantitative approach to underground mining problems, blasting research, or other related studies; however, the data are equally applicable to any problem wherein rock characteristics are important factors. Stress-strain curves are given where available, and the standardized procedure for determining elastic constants from static tension tests is described. Computed (laboratory) and measured (field) free-medium velocities are compared in those instances where such data are available. A chart is given showing both the optimum and minimum number of test specimens for the various core sizes employed in the Bureau of Mines standardized physical-property tests. Rock-type, geographical, and geological indexes are included to aid the reader in locating physical-property data in this and previously published Bureau of Mines physical-property reports.INTROD'OCTI ONThis report presents the physical properties of 84 rock types tested from 16 different projects (sections 37-52). Two previous physical-property reports 2-3 / (hereinafter referred to as parts I and II) presented data on 160 rock types from 36 different projects (part I, sections 1-25 and part II, sections 26-36).The physical-property data were originally obtained to supplement structural mining problems, seismic studies, or related investigations; however, they should be equally applicable in all fields of studies where the strength, hardness, or other properties of rock are important factors. The properties, determined from laboratory tests performed on diamond-drill core, include the following:"

Jun 1, 1955

By J. Bruce Clemmer

[Gypsum is one of the mo .. t iJf.l)ortant nonmp.tal1.ic T!1inerals, as is indicat-? ed by the fact that tlle Uni ted states cO!1sUl:Ied p, roximn..tely 3,500,000 tons of natura.l and calcinecl e::,j;-psum in 1937. The b\.'.ilr:.in.; traces \"fe.ro the largest users and required 2,520,000 tons of calcine for the r-roductiop. of plaster,]

Jan 1, 1941

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

By R. F. Tenney

This report has been prepared because little detailed information has been published on the production and use of anthracite producer gas for industrial-process and brick-kiln heating. To obtain this information, an investigation was conducted by the Federal Bureau of Mines in cooperation with a building-brick manufacturer (firing both periodic and tunnel kilns with anthracite producer gas) and with a manufacturer of anthracite-gas producers. In addition to a study of available plant records, 2 weeks was spent in systematic observation and measurement during regular operation of the Hazleton Brick Co. plant, Hazleton, Pa., in July 1953. This report presents the results of this investigation and a description of producer and periodic-kiln equipment, operating procedures, and labor requirements. A summary of the conditions of producer and kiln operation is given for the 2-week observation and for the 11 preceding months. The two 10-foot standard anthracite-gas producers consumed 301 tons of Rice and Buckwheat No. 1 anthracite, as delivered, averaging over 13,000 B.t.u. per dry pound during the 2-week period, with a producer hot-gas efficiency of 95 percent, at an average gas offtake temperature of 5400 F. The yield of gas5/ of 153 gross B.t.u. per cubic foot amounted to 140,000 cubic feet per ton of fuel as fired, or 73,500 cubic feet per kiln heating hour, which was sufficient for kiln requirements.

Jan 1, 1960

By Brian T. Brady

The year 1991 recorded unprecedented change throughout the world; war in the Middle East, economic recession in key industrial nations, upheaval in Eastern Europe, and the disintegration of the former U.S.S.R. These issues and growing environmental concerns will affect the entire world mining industry. Environmental issues continue to have an ever greater effect on industrial minerals. In the United States, major issues involving the Clean Air Act, Clean Water Act, and the recent Stormwater Rule by the U.S. Environmental Protection Agency (EPA) affect many types of mineral operations. Significant developments include an important decision in 1991 by a Federal Appellate Court to overturn EPA's asbestos ban on certain products, partly on environmental grounds, and proposed legislation that would overhaul or abandon the 1872 Mining Act. On a global scale, prominent issues include environmental concerns over mining in the Antarctic and Arctic regions and a cutback in plans to clean up the Kola Peninsula in the Commonwealth of Independent States (C.I.S.).

Jan 1, 1993

By W. H. Coghill, F. D. DeVaney

"Introduction Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with no many ""inflection points"" and ""counterflexures"" that they obscure the issue.Some of the investigators have neglected the very essence of the problem, namely, the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration.Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.Grindability Characteristics When the ores are being studied the information sought is grindability characteristics (grain-size distribution) and the grindability (work required to produce new surface) of a group of ores.When the study is of the machines, several machines are used for a given ore or given types of ores, and the grinding performances of the machines are compared by a grain-size study.Table 1 gives the grindability characteristics and grindability of six substances, one of which is coal. The substances are arranged from left to right in progressing order of tons per horsepower-hour. Curves and graphs are not needed for elucidation. The secret of the ease of interpretation is the order mentioned and the similarity of the sizing analyses. Power records must be complete in grinding studies.The grinding device was a ball, plunger, and mortar called the drop weight.' It may be used to advantage when the amount of material to be tested is too small for the orthodox machines.The upper part of table 1 shows the grindability characteristics by the cumulative-sizing analyses. Note how closely the percentage weights agree for a given sieve size. The lower part shows the grindability in terms defined elsewhere. The present paper should be read in conjunction with that paper."

Jun 1, 1934

By C. E. Wyndham

The occurrences of manganese In Alabama were reported to be widely scattered over the northeastern section of the State, and these were examined before a development project was started.2/ The most promising and available showings were chosen for further investigation, which include 1 deposit in Goshen Valley, 6 in the Rock Run area, and 2 in the northern section of Calhoun County. The work was performed by the Bureau of Mines from July 29, 1949, to February 17, 1950. The work consisted of power auger drilling 69 holes 3-1/2 inches in diameter and totaling 2,548.4 linear feet. The accuracy of samples from auger drill holes in this type of deposit was determined by sinking two shafts a total depth of 68.17 feet, from which channel samples were cut. Sixteen rotary core holes totaling 1,048.7 linear feet were drilled with a 3-inch, double-tube core barrel. Twenty-two diamond core holes were drilled with a 2-1/8-inch, double-tube core barrel and NX diamond bit. In addition to the above drilling 220.8 cubic yards of soil and rock was excavated by hand from 403.9 linear feet of trenches and 69.7 feet of test pita. A total of 206 samples were taken and analyzed for manganese, iron, cobalt, nickel, and insoluble.

Jan 1, 1953

By Ray J. Holmquist

"INTRODUCTION The Elk Mountain mica deposit was examined in June 1943 by the Bureau of Mines. An exploratory project and an access road for the property were recommended, provided the zinc was put in operation under competent management. K. Garard obtained a lease on the properly and started operations in June 1944; this was followed immediately by the Bureau's exploratory work. Road construction was begun by the Forest Service in July the same year.The lessee mined mica from the richest exposure with a crew of three men for 2-1/2 months. His operation terminated late in September, but the Bureau of Mines project and the Forest Service road construction continued until snow forced suspension of activity during the first week of November.The Bureau of Mines work consisted of trenching with a bulldozer, hand excavating on undeveloped outcrops, extending an existing adit, and starting a new adit below the older workings."

Jul 1, 1946

By R. V. Higgins

In a recent report3/ the authors presented a rapid method of calculating, by means of a desk calculator, the future performance of oil reservoirs in which the motivating agent was gas. The accuracy of the method was tested by data obtained from an electronic computer. Because of the accuracy obtained for the limited number of calculations performed, considerable interest has been expressed in the electronic computer program used to obtain the comparative data by an analytical solution. Accordingly, the computer procedures for the analytical solution are presented in this report. In an earlier report, 4/ a reservoir appraisal procedure was published in which an iterative method was used. Many requests were received for the computer program used to obtain the values given in that paper. That program, with some modifications, also is presented in this report. The modifications are given because of the progress that his been made in computers, and because much of the program for the analytical solution is usable for the iterative procedure.

Jan 1, 1960

By Arden D. Fugate

The Federal Bureau of Mines conducted extensive studies on solid-state defluorination (laboratory scale) and tests on molten defluorination (intermediate scale) of siliceous fluorspars. The studies were made to develop a pyrohydrolytic process for liberating fluorine from offgrade fluorspars. Test results showed that more than 90 percent of the fluorine can be evolved by solid-state defluorination at 1,300° C., and more than 97 percent can be liberated by molten-state defluorination at 1,420° C. Solid-state defluorination conditions were established by conducting tests on mixtures of ceramic-grade fluorspars and high-purity silica flour. Pelletized mixtures were defluorinated under varying conditions of time, temperature, and relative concentrations of silica, calcium fluoride, and water. The effects of adding various amounts and combinations of aluminum oxide and iron oxide on defluorination were also studied. Investigations of solid-state defluorination indicates that the following two reactions are involved: 2CaF2 + 3SiO2 = 2CaSiO3 + SiF4, and CaF2 + Sio2 + H20 = CaSiO3 + 2HF, The second reaction is dominant, although significant defluorination can be achieved by the first reaction.

Jan 1, 1961

By Oliver Bowles

The Bureau of Mines issued three Information Circulars on marble many years ago (5), (6), (7).2/ They have long been out of print; furthermore, conditions have changed considerably in the industry in succeeding years. A presentation of current data is therefore desirable. This report furnishes general information on marble, including its properties, distribution of domestic and foreign deposits, methods and equipment used in quarrying and milling, economic and marketing problems, and recent advances in marble technology. INTRODUCTION Most marbles are crystallized limestone. The term "marble" is derived from a Greek word meaning to sparkle or flash, because the calcite crystals in marble sparkle as they reflect light. The word "marble" is employed frequently to mean a small ball used in the game of marbles with which nearly every child is familiar. Although the little spheres were originally of marble, few of those made in recent years contain that material; nevertheless, the expression "playing marbles" has persisted.

Jan 1, 1958

By Robert T. Davis

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to the coal-mining industry's underground and open-pit mines that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1964

By Daniel S. Witkowsky

The Pollution Prevention Act of 1990 provides few specifics to assist the non-fuel mining and mineral processing industries of the United States in achieving pollution prevention (P2) compliance. The U.S. Bureau of Mines (USBM) recognizes the absence of specific information to reduce pollution impacts from mining and mineral processing of hardrock and industrial minerals. Therefore, the USBM has prepared this publication to help reduce or eliminate environmental pollution and to assure the viability of these segments of the domestic mining industry. This report includes worksheets designed to help operators of mining and milling facilities to establish a P2 program. The report can also be used by citizen and environmental groups, State and local governments, and academia to gain an understanding of P2 as it relates to mining and mineral processing.

Jan 1, 1995

By Seth C. Schaefer

The Bureau of Mines investigated the standard Gibbs energies of forma-tion AGfo, for NiCr204 (nickel chromite) and CoCr204 (cobalt chromite). High temperature galvanic cells employing stabilized ZrOz (zirconia) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1986

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor's response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor's head prevented catalyst poisoning efficiently.

Jan 1, 1981

By R. P. Walters, M. J. Lynch, D. R. Flinn

The Bureau of Mines evaluated tthhee feasibility of substituting platinum- coated metals for bulk platinum shapes as a means for conserving platinum . Platinum coatings were prepared using four different methods of electrodeposition , then tested and evaluated . In order for platinum coatings to be useful in process environments , they must be thick , adherent , stress - free , and pore - free . The Bureau evaluated direct - current , current reversal , cathode shielding , and pulsed- current plating techniques for producing a pore-free platinum electrodeposit from a molten cyanide bath . Aqueous corrosion tests of Fe - 10Cr substrates coated with approximately 25 μm of platinum showed that pulse plating yielded the most corrosion- resistant and , hence , the most pore -free coatings . The morphology of coating cross sections was in all cases columnar . The average grain size of pulse -plated deposits was independent of thickness , while all other plating techniques produced grains that increased in size as the coatings became thicker . It is believed that the constant grain size in the pulse - plated deposits resulted from better mass transport during the electrodeposition .

Jan 1, 1965

By F. A. Rutledge

The W. E. Dunkle mine, sometimes called the Costello Creek coal mine, is 8 miles N. 20° W. of Colorado Station on the Alaska Railroad. The presence of coal in this area has been known since the district was extensively prospected for gold between 1911 and 1915. At that time, coal from this deposit was used by miners for blacksmithing. The increased demand for coal resulting from government defense projects in Alaska led to exploitation of this deposit in 1941. The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska was responsible for establishment by the Army of the Coal Procurement Section of its Alaska Department. It proposed to investigate the deposits and to expedite production from the Alaskan coal fields. The Bureau of Mines closely cooperated in this program. The quality of the Dunkle coal and the favorable location of the deposit caused it to be one of the properties chosen for investigation under a joint Army-Bureau of Mines-Geological Survey program.

Jan 1, 1948