Search Documents

By Deborah A. Kramer

This Bureau of Mines report presents a cost estimate of the Bayer process, which is used for virtually all cell-grade alumina production. The report will serve as a reference point to determine the economic merits of processes that have evolved from Bureau of Mines investigations on technology for producing alumina from domestic nonbauxitic raw materials. The Bayer process involves dissolving the alumina present in bauxite in a caustic solution at high temperature and pressure. After the un- dissolved impurities are removed, the solution is seeded to produce an alumina trihydrate precipitate. This precipitate is filtered, washed, and calcined to produce the cell-grade alumina product. This cost estimate is for a plant producing 1 million tons of alumina per year. The estimated operating cost is approximately $250 per ton of alumina.

Jan 1, 1983

By J. E. Chilton

Interim performance specifications are presented for carbon monoxide, methane, and air velocity transducers used in the Bureau of Mines intrinsically safe mine monitoring system. These specifications give quantitative values or qualitative descriptions of the transducers, including environmental parameters and monitoring system measurement and maintenance requirements as recommended by the Bureau of Mines. Commercially available transducer modules and prototype modules are listed together with selected characteristics.

Jan 1, 1983

By M. L. Skow

Large tonnages of the manganese ores found in Aroostook County, Maine, are refractory to conventional mineral-dressing techniques and to the common chemical- extraction procedures. The Maple Mountain-Hovey Mountain ores are typical of this type. Because the most promising method of recovering the manganese from these ores has been a chloridizing roast in which the ground ore is in contact with gaseous hydrogen chloride, preliminary batch tests were made with a fluidized bed. On the basis of these tests, it was concluded that fluidization, with careful control of operating conditions, could be employed for this cloridization and warrants further study. Selective volatilization of the iron at 600° C. was unsuccessful. An operating temperature of approximately 950° C. was necessary for a practicable rate of volatilization of manganese chloride. Hydrogen chloride contents of 10 to 100 percent of the fluidized gas gave essentially equivalent manganese recoveries with an 80- minute retention time, For shorter periods reaction was more complete with the higher hydrogen chloride concentrations. At the 80-minute retention period the lower hydrogen chloride concentrations volatilized somewhat less iron and also improved the physical operation of the process. Fluidization gave results superior to comparable tests on chloridization in a fixed bed.

Jan 1, 1956

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines report to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios were prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1993

By W. D. Striffler

Land disturbed by surface mining in Colorado and other western states has increased substantially over the past several years and is likely to increase even more in the future. This study was initiated to provide basic information on hydrologic and erosional characteristics of regraded coal spoils in Colorado as an aid for planning future reclamation activities. Eleven of twenty-one surface mines licensed in Colorado were sampled during the summer of 1980 and 1981. Mines not sampled included mines which had not progressed to the point that reclamation had begun, and mines where operators denied permission to sample. All coal regions were sampled with the exception of the San Juan Coal Field. Physical and hydrologic characteristics of regraded coal spoils in Colorado were determined using standard field and laboratory procedures. Field sampling included characterization of sites (slope, vegetation density, proportion of surface rock, bare soil, etc.) and infiltration measurements using a l-meter square drop former raining on a 1/2 square meter rectangular plot frame. Core samples collected in the field were analyzed for saturated hydraulic conductivity, bulk density, organic matter, moisture retention and texture. The erosion potential of each site was determined using the Universal Soil Loss Equation (USLE). Results of the sampling indicate that infiltration rates vary widely both within and between sites. However, definite trends with respect to coal fields are apparent. For example, the Green River (Yampa) coal region had a wide range of sampled infiltration rates (1.2 to 5.1 cm/hr). However, most of the sites clustered towards the low end of the range. The North Park (Marr Strip) also was rated at the low end of the infiltration range (2.0 to 3.0 cm/hr). Average infiltration rates for the Canon City and Uinta Coal Regions were at the high end of the range (4.9 to 5.5 cm/hr). Multiple correlation analysis of infiltration rates vs. site characteristics showed that infiltration rates were most closely correlated with the depth of wetting, the amount of mulch cover, and site slope. The depth of wetting was highly correlated with the depth of the topsoil and the bulk density of the spoil. In general, the topsoil at all sites appeared to be highly permeable to water intake but once saturated, subsequent infiltration depended upon characteristics of the underlying spoil. Vegetation cover affected infiltration on individual mine sites but was not as pronounced as topsoil characteristics or mulch. Erodibility of topsoil and spoils, as determined by Wischmeier's "K" factor, ranged from 1.34 to 0.56 tonnes/ha. (topsoil) and 1.25 to 0.66 tonnes/ha. (spoils). Definite trends in erodibility are evident. The Green River (Yampa) Coal Region displayed consistently higher erodibilities (1.34 to 0.75 tonnes/ha.) than other coal fields (0.72 to 0.56 tonnes/ha). Lowest erodibilities were observed in the Uinta, North Park, and Raton Mesa Coal Regions (0.56 to 0.62 tonnes/ha). Erodibilities of underlying spoils showed similar trends as the topsoils. Erosion potential (the product of soil erodibility and rainfall erosivity) was detennined using calculated ?K? factors and rainfall erosivities (R) taken from Clyde (1976). Results show that the Delagua coal field, Raton Mesa Coal Region had the greatest erosion potential due to the high rainfall energies in the region, while the North Park and Uinta Coal Regions had the lowest potential erosion.

Jan 1, 1981

By E. T. Bowers

Pneumatic conveying of coal underground is not widely used in the United States, although it is becoming increasingly popular in Great Britain, the Federal Republic of Germany, and South Africa. The question of safety has been raised repeatedly: Will the system be prone to dust or gas explosions, and, if so, can it withstand such occurrences safely? The work reported here was done under a Bureau of Mines contract and deals with the safety aspects of pneumatic transport of underground coal, as well as the hazards inherent in more conventional haulage systems. Included are three designs for different applications of pneumatic haulage: off-loading a continuous-mining machine on a room- and-pillar section, vertical hoisting through a 1,200-ft shaft, and off-loading a tunnel-boring machine driving a 2,000-ft tunnel.

Jan 1, 1985

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced with the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production must be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a as supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, sortie fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case. The Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla., has been interested in problems connected with air-repressuring for a number of years. Some time was spent in studying the so-called "bad gas"--return mixture of low fuel value. However, it appeared impossible to attack the problem successfully from this angle, and an approach was made through a laboratory-scale study of direct oxidation of crude oil.

Jan 1, 1934

By Charles Prasky

The Bureau of Mines investigated the conversion of nonmagnetic iron minerals to magnetic form through reduction Toasting operations. The primary objective was to obtain a concentrate that could be used as a direct shipping material for blast furnace consumption. Crude iron materials from the Steep Rock Lakes, Ontario, area were prepared into a blend of 8 parts siliceous ore, 3 parts pyritic ore, and 1 part tailings. Experimental work included laboratory reduction roasting tests, two continuous 10-day campaigns, and one 12-hour test all in a 34-inch by 36¬-foot rotary kiln. The objective of the project was achieved in producing an iron concentrate containing about 66 percent iron with over 90 percent iron recovery. Desirable operating conditions were developed in the kiln but optimum process variables were not completely established.

Jan 1, 1969

By H. D. Hess, C. P. Mabie

This report describes in detail the results of petrographic research conducted on 21 phosphate ores representing important deposits in southwestern Montana , southeastern Idaho , and northeastern Utah . The ores are described and categorized by mineralogical and chemical composition , thermal behavior of organic carbon , and textural constitution . Descriptive and genetic classification schemes applicable to western phosphate ores are discussed ; results from related studies made of the collophane mineralogy are also presented . The latter studies were centered on determining unit - cell dimensions and CO₂ , P2O5 , and fluorine content of collophane concentrates of 11 high - grade phosphate- rock hand specimens selected solely for this purpose . On the basis of this investigation , operational methods have been developed for quantitatively describing textural and compositional features that are likely to be significant in determining the response of phosphate ores to conventional beneficiation treatments ; systems for classifying the ores in relation to these features have been proposed . Studies to date point out distinct textural and compositional variations in the western phosphates and illustrate their importance in determining optimum beneficiation procedure .

Jan 1, 1964

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By A. M. Evans

"INTRODUCTION Exploration of the Iron Mountain and Bader iron-ore deposits in Llano County and the Gamble deposit in Mason County, Texas, was begun by the Bureau of Mines in January and completed in May 1944. The deposits had been examined by A. B. Needham, district engineer of the Bureau, in November 1942. Detailed geophysical studies by the gravity method as well as with a dip needle were made by the Bureau of Economic Geology 3/ of the University of Texas and the Federal Geological Survey. 4/ACKNOWLEDGMENTSIn the program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy., It is the policy of the Bureau to publish the facts developed by each exploration project as soon as practicable after its completion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947

By Michael S. Miller

In 1987, 1988 and 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the Sperry Creek Wilderness Study Area (OR-003-035; 5,600 acres) and the Gold Creek Wilderness Study Area (OR-003-033; 13,600 acres), plus an additional area (OR-003-033; 2,180 acres) adjacent to the Gold Creek Wilderness Study Area. The wilderness study areas and the addition are south of the Malheur River and are about 20 miles east of Juntura, Oregon. The wilderness study areas and the addition are underlain by volcanic rocks, predominantly basalt and rhyolite flows, breccias, and welded ash-flow tuffs. Lacustrine deposits containing diatomites occur mainly at the east side of the Gold Creek Wilderness Study Area and addition. Alluvium lies along the Malheur River, in terraces and fans south of the Malheur River, and along the floors of some creeks. Shear zones and faults have offset the rocks and provided channels for eruption of volcanic rocks and epithermal mineralization by hot springs.

Jan 1, 1989

By C. Thomas Hillman

This Bureau of Mines report describes an investigation of factors influencing economic viability of a proposed system to mine and process manganese nodules. The system consists of hydraulic dredging and ammonia leach processing designed to recover three metals: nickel, copper, and cobalt. A ferromanganese recovery plant is a considered option. Annual capacity is 3 million dry metric tons (t) nodules. Aftertax rates of return (ROR's) of only 7.38 and 6.63 pct are predicted for three-and four-metal base scenarios, respectively. Sensitivity analyses indicate that variations in commodity prices, metal recoveries, and deposit grades produce similar incremental changes in ROR. Estimated cumulative effects of price variations are greatest. While three-metal operations generally yield higher predicted returns, potential increases in manganese price and process recovery could make four-metal operations most profitable. Maximum variations in both capital costs and three-metal operating costs result in ROR changes of about 25 pct. In contrast, four-metal ROR's exhibit variations to 70 pct. Even so only a best case analysis, utilizing favorable variations in all categories tested, generated ROR's approaching a level thought necessary to trigger company interest. Consequently, it is concluded that nodule mining will not take place in the foreseeable future without significant financial incentives.

Jan 1, 1985

By G. E. McElroy

Changes in existing airway and fan-installation conditions offer the most common opportunities for effecting economical operation of mine ventilating systems, but the largest possibilities for securing this result lie in the original design of the main airways for efficient service. Formulas, and. charts for their graphical solution, are presented herewith for the determination of the elements of airways design when the conditions of service are known, or may be roughly approximated. Although the analyses are made with particular reference to metal-mine airways, there is no essential difference between metal and coal mine main airways, and the methods presented are equally applicable to both. Little attention is paid to designing airways for maximum economy in the ventilation of metal mines. Most of the openings used as main airways are originally designed and used for transportation and other operating purposes. Even where openings are made primarily for ventilation, the possibility of their future use for other operating purposes, or even custom alone, usually results in the selection of a size and shape similar to those of existing openings. Natural conditions, such as heavy ground, often seriously limit the size of opening that can be maintained without excessive expense; and various operating factors, such as velocity limitations on traveling roads, often dictate size requirements in excess of those required for economy in ventilation only. In metal mines the main airways are, as a rule, too small rather than too large for economic service, with the general result that the quantities in circulation are often less than the mine's proper requirements over long periods, even though excessive amounts of power are applied in an effort to remedy conditions.

Jan 1, 1932

By R. L. Crosby

The Bureau of Mines investigated alloys of copper with 2, 3, and 4 vol pct alumina and with 2 vol pct yttria. Alloys were prepared by a coprecipitation process and were fabricated by pressing and sintering of powders, extrusion, and swaging. Tensile properties at room and elevated temperatures, stress-rupture strength, electrical conductivity, and density were measured. The superiority in elevated temperature strength of dispersion-strengthened copper to OFHC copper was confirmed. Increasing the oxide content from 2 to 4 vol pct produced only a small improvement in strength properties and decreased the electrical conductivity. The 3 vol pet alumina alloy had the best overall combination of properties.

Jan 1, 1969

By S. P. Kinney

Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. An example of the result of inefficient gas-solid contact in the shaft of a blast furnace is shown by the curves in Figure 1.

Jan 1, 1930

By Bernard J. Steblay

The U.S. Bureau of Mines has attempted to use ultrasonic signal travel-time measurements to measure loaded roof bolt strains. The strain measurements are then related to roof bolt loads through equations or empirical calibrations. Such techniques offer the potential of accurate, rapid bolt load measurement that does not disturb the anchotage. This report presents 6e research findings for a specific type of ultrasonic measurement instrument using a pulsed-phase-Iock-Ioop technique. This technique measures signal travel time indirectly by measuring frequency changes. A complete development of the applicable theory and detailed derivations of key equations is presented along with empirical laboratory and field results. The differences between anticipated and measured behaviors are analyzed and discussed. The report identifies problems encountered in applying pulsed-phase-Iock-Ioop technology to roof bolt load measurement and provides potential solutions to many of them. A key assumption of pulsed-phase-lock-loop theory is that driving and reflected signal frequencies will always be equal. Findings showed that not only were actual frequencies not equal but they were not stable or simply related. Reflection wave shape also was not stable. The ramification of these findings and ways to minimize their adverse effects are presented.

Jan 1, 1990

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By Ben A. Kornhauser

The mineral industry consisted primarily of natural gas production and of urea fertilizer, which was manufactured for domestic agriculture. Copper and iron deposits were being developed. Information regarding the mineral industry of Afghanistan was sparse. The Government continued to emphasize the development of mineral resources that could benefit the economy of the U.S.S.R. and repay Soviet grants. The northern half of the country, north of the Hindu Kush mountain range and adjacent to the U.S.S.R., received considerable Soviet aid to develop mineral resources.

Jan 1, 1986

By W. H. Young

In response to increasing national energy requirements. highlighted by the continuing growth in demand for coal for the generation of electric power the output of bituminous coal and lignite in 1965 passed the 500-million-ton mark for the first time since 1956, thus emphasizing the steady up-ward trend from the recent low of 403 million tons in 1961. There were corresponding upward trends in consumption, exports mechanization, and productivity. Production.-The output of bituminous coal and lignite in the United States in 1965-512 million tons-was 5 percent greater than the 487 million tons produced in 1964. The gain was attributed largely to expanded consumption by the electric utilities, greater use at coke ovens, and an increase in exports.

Jan 1, 1967