Search Documents

By R. L. Levens

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface area exposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 2010

By W. A. Cole

This report covers the preliminary phase of an investigation of some clays and shales and other materials in North and South Dakota to determine the feasibility of lightweight -aggregate manufacture in the two States. The background of the light - weight -aggregate industry, on a national basis, and results of preliminary laboratory testing of samples of North and South Dakota clays and shales from various localities are presented herein. The countrywide search for lightweight aggregates was necessitated toward the end of the 19th century by the change in building design from thick, heavy, load- bearing walls to a framework of structural steel .beams and columns with thin walls, followed shortly by the use of reinforced concrete and structural concrete as materials for the load-supporting frame. Ordinary concrete, with sand and gravel aggregate, weighs about 150 pounds to the cubic foot. A lighter concrete was needed to relieve the dead load and make it possible to construct higher buildings or add stories to existing buildings.

Jan 1, 1954

By Edward E. Johnson

The Bureau of Mines publishes in its ?Minerals Yearbook? a series of indexes on the domestic minerals industry. Among these are the index of physical volume of mineral production, indexes of stocks, and indexes of average unit mine value and implicit unit value, This report describes the material coverage of these indexes and the methods used in their construction. Detailed descriptions are given for several other mineral-oriented indexes regularly published by other government agencies. These descriptions give the index user a better understanding of what each index purports to measure and aids him in selecting the most appropriate index for his purpose.

Jan 1, 1965

By Edward E. Johnson

The Bureau of 'Mines publishes in its ?Minerals Yearbook? a series of indexes on the domestic minerals industry. Among these are the index of physical volume of mineral production, indexes of stocks, and indexes of average unit mine value and implicit unit value, This report describes the material coverage of these indexes and the methods used in their construction. Detailed descriptions are given for several other mineral-oriented indexes regularly published by other government agencies. These descriptions give the index user a better understanding of what each index purports to measure and aids him in selecting the most appropriate index for his purpose.

Jan 1, 1965

By Griffith. F. E., Glei

"INTRODUCTION For many years protective grounding of electrical equipment has been advocated as a means of safeguarding equipment against damage and of minimizing shock hazards to persons. Several codes are in effect covering in considerable detail the items to be observed in obtaining effective grounding in and about industrial plants. Although the coal-mining industry does not have a comprehensive code of its own covering the grounding of electrical installations, a number of States and individual coal-mining companies have issued codes, standards, or rules that include certain requirements with reference to grounding. As early as 1916, 4/ and again more recently, 5/ the Bureau of Mines recommended grounding, particularly as a means of preventing shock to men working on or around electrical equipment.It is common knowledge among electrical engineers of public utility and mining companies that connecting a wire from the frame of a machine to a rod or pipe driven into the earth does not necessarily assure desired protection of surface equipment. In fact, it has often been found necessary to use several interconnected rods and to treat the surrounding earth with salt or other chemicals before the connection to earth would have sufficiently low resistance to give satisfactory results. Even these expedients have not produced the desired results in some localities. It has also been found that ground connections initially having a low resistance may attain high resistance during some seasons of the year. In spite of such difficulties with surface equipment, it has sometimes been assumed that a mining machine resting on the floor in a coal mine is grounded by virtue of its contact with that floor. It has also been assumed by persons endeavoring to comply with grounding requirements that a peg or rod driven into the mine floor would provide a sufficiently low-resistance contact with the earth to be satisfactory as an electrode for connecting the grounding wire from frames of equipment. That both assumptions may be wholly untrustworthy has been proved by the authors in actual tests with underground machinery."

Dec 1, 1943

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By BUREAU OF MINES

This report is submitted in accordance with the provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1953 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5043, Part I - 011 From Coal. R. I. 5044, Part II 011 From 011 Shale. - Identical in each report, the introduction summarizes research progress made in 1953 under the entire Synthetic Liquid Fuels program. A free copy of each of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Apr 1, 1954

By Frank G. Schwartz

VARIABLES OF composition and environment affecting storage stability of gasoline-type fuels were studied, utilizing radioactive tracers and other analytical techniques. Changes in gasoline composition brought about by aging were determined and correlated with gum formation. The amounts of reaction of selected gasoline components, measured by radioactive tracers, were determined in a gasoline-type blend and in a mixture of 17 selected pure gasoline components. The data show that sulfur compounds, nitrogen compounds, polycyclics, and olefins enter into gum-forming reactions. Certain sulfur and nitrogen compounds were found to be most reactive in the gum-forming process. Results of this study indicate that the aromatic constituents of gasolines may contribute substantially and directly to gum formation. A mixture of tetralin and indan-type compounds is reactive, and this mixture appears to be the main aromatic portion entering into gum formation. A secondary but significant amount of naphthalenes also appears to have reacted in the gum-forming process. Analyses of the sulfm compounds in a fresh and an aged fuel indicated that elemental sulfur, hydrogen sulfide, thiols, sulfides, and disulfides were depleted during aging, but thiophenes and residual sulfur compounds were not depleted by fuel deterioration.

Jan 1, 1964

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and Other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investi-gation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from some oil fields of Louisiana are given in Bulletin 291. Analyses Of 26 representative crude oils from various producing formations of southern Louisiana are given in this report. These samples are from 14 fields in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area."

Jan 1, 1934

By G. W. Birge

This report describes the carbonizing properties of the principal coal beds of McDowell County, W. Va. Coals from 14 coal beds were selected for study: Upper Cedar Grove, Middle Cedar Grove, Lower Cedar Grove, Eagle, Douglas, Iaeger, Sewell, Welch, Beckley, Fire Creek and Pocahontas Nos. 3, 4, 5, and 9. Selection was based upon estimated minable reserves. McDowell County coals rank either as high-volatile A, medium-volatile, or low-volatile bituminous coal, and this variation in rank is reflected in the wide diversity of the carbonization properties of the coals. All coals tested were either satisfactory as mined or could be upgraded to meet present chemical standards for metallurgical coke; the coals produced strong coke, as determined by ASTM shatter and tumbler tests.

Jan 1, 1958

By R. A. Friedel

THE UTILIZATION by the Bureau of Mines of infrared and ultraviolet-visible spectrometry in connection with coal research has led to some basic improvements in methods, including a calibration method, a quantitative assessment of infrared spectral energy sources, and the development and perfection of infrared filters and cells. The adoption of a micropipet method to flush organic samples into absorption cells permits the investigation of vapors from organic liquids and the identification of volatile organic compounds. The spectral method has been used to investigate the infrared spectra of metal chelates, the charge-transfer complexing properties of aniline and nitrobenzene, an infrared method for determining the presence of methane in coal-mine air that has been adopted for use in enforcing the regulations of the National Coal Mine Safety Act, and atmospheric pollution including smog and odor-causing oxidation and decomposition of organic materials. Correlation of spectra and structure of organic compounds, particularly aromatics, was studied.

Jan 1, 1966

By P. A. Hendricks

This U.S. Bureau of Mines (USBM) report identifies and evaluates factors responsible for metal/nonmetal (M/NM) underground mining accidents involving mobile equipment. Information regarding the occurrence and severity of the accidents, the type of equipment involved, the primary and contributing causes, and preventive measures is included. The goal of this report is to provide information that will aid mine operators and safety managers in the recognition of hazards associated with operating mobile mining equipment in an underground mining environment.

Jan 1, 1994

By John C. Machisak

THE INJURY data and experience at quarries and related plants of the United States are presented in this publication under the following general sections : (A) General injury experience: Tables 1 through 3: Contain current data on the number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 4 and 5: Contain current data on number of injuries, injury- frequency rates, location, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 6 through 19: Contain current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data.

Jan 1, 1959

By A. T. Coumbe

The first national survey covering sales of fuel oil by States and principal uses was made in 1926 by E. B. Swanson of the Bureau of Mines (then under the U. S. Department of Commerce) under a cooperative agreement with the American Petroleum Institute. This annual study, covering the market for fuel oil, was made through 1930 with the financial help of the institute bat has since been continued by the Bureau up to the present time. The scope and coverage of the survey have gradually changed over the years as new uses for fuel oil have been found and new products have come into importance resulting in market expansion. Range oil (No. 1 fuel oil or kerosine) came into use for cooking and space-heating daring the depression era in New England, and it was first reported as a total in the 1931 survey. In 1934 the sales were compiled on a State basis. State totals for distillate fuel oil, Diesel fuel, and residual fuel-oil sales were first shown for 1934 and by principal uses and States in 1937. Kerosine deliveries by States and main uses were also released for the first time in 1937.

Jan 1, 1952

By William T. Boyd

Foreign mining publications describing successful hydraulic mining installations, and successful domestic hydraulic mining in a gilsonite bed, have prompted the Federal Bureau of Mines to conduct a literature survey of foreign publications to determine if the hydraulic mining method can be applied to domestic coal mining. Most foreign publications do not give detailed data about the water pressures, water capacities, and production and manpower requirements for successful hydraulic mining, However, they do provide enough general data on mining conditions, manpower, and equipment used to show that conditions in many bituminous coal deposits in the United States may be favorable for economical coal extraction, using high-pressure water jets. Therefore, the Bureau proposes to conduct a field investigation to determine the most appropriate natural conditions, water pressures, and equipment for successful hydraulic mining of coal beds in the United States with variable dip, thickness, and hardness. In the past, technical personnel reviewing foreign mining reports assumed that a steeply pitching coal bed was necessary for successful hydraulic mining. Although the structure of the coal bed may be a factor in gaining assistance from overburden pressures or help in an integrated hydraulic mining and transportation system, the coal is broken mainly by the action of high-pressure, water-penetrating cracks, fissures, or cleats; therefore, the slope of the coal bed is not necessarily a determining factor in hydraulic mining.

Jan 1, 1959

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples tom some oil fields of Louisiana are given in Bulletin 291.4/ Analyses of 26 representative crude oils from various producing formations of southern Louisiana are given in is report. These.samples are from 14 field's in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area." ACKNOWLEDGMENTS Thanks are due the representatives of the various companies from whom samples were obtained for their cooperation and assistance in helping to secure representative samples. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1934

The Mateen deposit comprises two large spodumene-bearing pegmatite dikes that outcrop along the, side and crest of a hill overlooking 'Rill City in the southern Black Hills of South Dakota. The Bureau of Mines investigated the Mateen deposit as part of a comprehensive study of the lithium mineral-production possibilities in the Black Hills area. The work was undertaken during the second World War, when the demand for certain lithium salts and compounds exceeded the small productive capacity of the industry. During the course of the investigation, the Bureau of Mines took 61 large channel samples from surface trenches, 4 channel samples from a shaft, and 3 from the face of an open cut. In addition, 8 diamond core-drill holes were completed to investigate the attitude of one of the dikes at depth. Metallurgical tests were conducted by the Bureau of Mines to determine the feasibility of beneficiating spodumene-bearing ores from the Mateen dikes.

Jan 1, 1948

By Robert L. Lagace, Michael A. Grossman, Alfred G. Emslie

This supplement to the final report is a collection of interim and monthly reports and working memoranda prepared during the course of this program to document the progress, methods and results of the work. The supplement is divided into the self-contained sections briefly described below. I. SELECTED MONTHLY TECHNICAL LETTER REPORTS - This section is a collection of selected monthly technical letter reports that briefly summarizes the chronological development of the analyses and results, including the different concepts, theoretical approaches, and methods of data reduction and analysis explored, and the discoveries, insights and findings made along the way. More detailed treatments of the key developments and results are presented in the interim reports and working memoranda reproduced in subsequent sections of this supplementary report, and in the separately published final report. II. BACKGROUND THEORY FOR MEASUREMENT PROGRAM ON MEDIUM AND HIGH FREQUENCY RADIO TRANSMISSION IN COAL SEAMS - Working Memorandum - This working memorandum gives the initial background theory needed to guide the planned measurements and data analyses of this program to describe the propagation of radio waves-in coal seams for the frequency range of 50 to 5000 kHz. III. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION - Interim Report - This interim report presents detailed treatments of the data analysis and modelling techniques used, and the associated results obtained from conductor-free area propagation data measured by T. Cory in the first set of six coal mines. The mines were located in three highcoal seams; the Pittsburgh seam in northern West Virginia, the Pocahontas No. 3 seam in Virginia, and the Herrin No. 6 seam in Illinois. IV. ANALYSIS OF MF PROPAGATION DATA FROM MARGARET NO. 11, NANTY GLO, EHRENFELD, AND ADRIAN COAL MINES - Interim Report - This interim report presents detailed treatments of several improved data analysis and Modelling methods applied to, and results obtained from, conductor-free area propagation data measured by T. Cory in the second set of four coal mines. These mines were located in three low-coal seams; the Upper Freeport seam in Pennsylvania and West Virginia and the Lower Freeport and Lower Kittaning seams in Pennsylvania. In addition, this report contains a reprint of two papers presented at a Bureau of Mines sponsored EM Guided Waves in Mine Environments Workshop held in Boulder Colorado. One paper describes the three-layer theoretical model and its application to the conductor-free data from the first six mines, while the second paper describes the theory developed for the coupling of loop antennas to a cable in a mine tunnel in a coal seam, and the model's application to data in the vicinity of cables taken at the Margaret No. 11 mine. V. A METHOD FOR NONINTRUSIVE, IN-SITU MEASUREMENT OF COAL AND ROCK CONDUCTIVITIES IN A COAL MINE TUNNEL - Working Memorandum - This working memorandum briefly describes a possible direct method, and its potential advantages and shortcomings, for performing in-situ measurements of coal and rock conductivities. VI. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION FROM 50 to 5000 kHz - Interim Report - This interim report presents a summary comparison of theoretical and experimental results for conductor- free areas in eleven coal mines located in seven coal seams. It also summarizes the findings and their implications for intrinsically-safe, portable radio communications between roving miners.

Jan 2, 1980

By Joseph J. Wallace

1. The investigation shows that nine coal beds have been mined in Harlan County, of which the Harlan and Upper Elkhorn No, 3 are the most important from the standpoint of present production. Of less importance are the Hindman, Flag, Haddix, Wax, Fire Clay, Armburgy, and Upper Elkhorn No. 2. The Harlan, Upper Elkhorn No. 3, and Upper Elkhorn No. 2 beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 2,138 million short tons as of January I, 1932. Of this total, 1,956 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study, Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954