Search Documents

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International, Inc. (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period from 6 September to 9 September 1983. The testing covered herein is for coarse 2-in by 0 (minus 50 mm) Pittsburgh Seam run-of-mine (ROM) coal in a 12-in (300 mm) pipeline, at velocities ranging from 8 to 16 ft/s (2.4 to 4.9 m/s) and at concentrations ranging from 15 to 50 pct.

Jan 1, 1985

By George T. Motock

In Germany the extraction of lithium and its salts has been handled mainly by units of the two major concerns - Metallgesellschaft A, G. and Deutsche Gold und Silber Scheide Anstalt, both with headquarters in Frankfurt. Zinnwaldite, which belongs to the mica group, is the major source of the lithium-containing raw material in Germany. Lepidolite and amblygonite also are used when available, but they are imported, as there are no major deposits of these two minerals in Germany.

Jan 1, 1946

By Paul Zinner

An exhaustive program of geologic studies and mapping has been conducted by the Geological Survey in the Iron River district of Michigan since May 1943. Means of contributing to the success of these studies were sought by the Bureau of Mines, and eventually a program involving geophysical studies and core-drilling was undertaken in the area. All of the work was done either to develop data that would contribute directly to geologic studies or to investigate geophysical methods that might be used as a primary means for the discovery of minable iron ore.

Jan 1, 1949

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to estimate what effects the underground mining of thick coal seams in the western United Slates would have on the surrounding water resources. Potential coal fields in the western United States where this type of mining might occur were identified. The foreign literature was searched for studies of effects on hydrology from thick seam underground coal mining. Based on the limited information obtained from the foreign literature, estimates of the effects of this type of mining on the ground and surface water in the western states were made.

Jan 1, 1980

By G. R. Hopkins

The average gravity of the total crude petroleum produced in the United States during; the year 1927 was 32.2° A. P. I., or 0.864 in terms of specific gravity. A similar study, made by the U. S. Geological Survey in 1921, gave the average gravity at that time as 32.0.° To one who is accustomed to thinking of crude petroleum in terms of Oklahoma-Kansas and North Texas trades it may be surprising that the average gravity for the entire country is no higher than 32.20. The chief reason for this apparent discrepancy lies mainly in California production, which in 1927 amounted to over 25 per cent of the total, but which had an average gravity of only 24.10. A factor of less importance was Arkansas, which, though on the decline as a producing State, exerted a material effect by reason of its average gravity of 21.6°, the lowest for any State. In view of the heavy production of light crude in the Seminole area of Oklahoma during 1927, it would appear that the average gravity should have shown more than a 0.2 per cent gain over 1921. That this did not occur was due to the fact that in the interim between 1921 and 1927 important heavy oil discoveries were redo, notably the Smackover field of Arkansas.

Jan 1, 1929

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

By H. H. Schrenk

[There is a need for method of determining: benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the modification of the Elliott and Dalton6/ procedure. This depends on the nitration of the benzene to reduction to phenylenediamine with all excesses of standard titanous chloride; solution, and titration with e standard ferric ammonium sulphite solution. This method has the disadvantages of being what time consulting: and cumbersome it requires considerable apparatus, and a special modification is necessary in the presence of toluene.]

Jan 1, 1935

By H. H. Schrenk

There is a need for a method of determining benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the Smyth modification of the Elliott and Dalton procedure. This depends on the nitration of the benzene to m-dinitrobenzene, reduction to phenylenediamine with an excess of standard titanous chloride solution, and back titration with a standard ferric ammonium sulphate solution. This method has the disadvantages of being somewhat time-consuming and cumbersome; it requires considerable apparatus, and a special modification is necessary in the presence of toluene. Recently Cook and Ficklen have published a method based on the oxidation of benzene with hydrogen peroxide in the presence of iron salts. This method requires the use of solid carbon dioxide to freeze out the benzene. The reaction Which produces the color is complex; and only approximate quantitative estimations can be made, except in a very narrow range.

Jan 1, 1935

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Arkansas has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251 of which this is the tenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of which deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated. and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By W. M. Merritts

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining, This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes, In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased.

Jan 1, 1962

By Amitava Ghosh

A new analytical formula for predicting ground vibrations induced by blasting is proposed. One factor accounts for geometrical spreading. One factor corresponds to inelastic attenuation. The geometrical spreading function is based on likely source geometries, idealized as either square-root, cube-root or site-specific scaling, and on the propagation characteristics of predominant wave types. The inelastic attenuation is approximated by an exponential function. The empirical constants in these functions are backcalculated from field measurements. Regression analysis has been performed on twenty-three sets of measured data in order to determine the validity and the effectiveness of the proposed method. In many cases, the proposed method gives better correlation than the conventional method. In most of the remaining cases, there was no difference between the two methods. Best-fit lines given by the proposed method fit the data trend very well, especially at large scaled distances. At large distances the proposed method gives a prediction much closer to the actual values than the conventional methods. The statistical analysis shows not much difference between square-root, cube-root or site-specific scalings.

Jan 1, 1983

By M. H. Chetrick

An important factor in the design and operation of a lignite-gasification plant is knowledge of the thermal requirements. These not only vary with different-size plants but also with the operating conditions for a plant of given capacity. Thermal data have been collected since 1945 from a commercial-scale lignite-gasification pilot plant operated by the Bureau of Mines at Grand Forks, N. Dak. The description and operation of this plant and a study of the gas-composition data have already been described in previous reports (1, 2, 3, 4, 5).2) / This investigation was made to review the thermal data taken in tests and to correlate them in terms of the fraction of undecomposed steam and the H2:CO ratio.

Jan 1, 1953

By O. C. Blade

This report on the properties of burner-fuel oils produced during 1956 was issued under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, at the request of the Oil-Heat Institute of America and the petroleum industry. This survey is the second for this type of fuel, the first being made in 1955. 2/ The surveys are conducted to provide information on the characteristics of burner-fuel oils now manufactured for sale. They are similar in pattern to the diesel-fuel surveys, conducted since 1950, 3/ and are not intended to conflict with but rather to supplement them. The importance of fuel oil has resulted in the need for more information by the petroleum industry, manufacturers of heating appliances, and consumers regarding the types and qualities of the fuels currently being marketed. Samples of burner-fuel oil typical of their manufacture during the early part of 1956 were analyzed by the refiners in accordance with instructions from the subcommittee on fuel surveys of the Automotive Research Committee of the American Petroleum Institute, Results of the analyses were transmitted to the Bureau of Mines where the data were studied and compiled as shown in the tables of this report.

Jan 1, 1956

By A. W. Fahrenwald

"The rate of progress in the last three years in the development of differential flotation has been rapid beyond the realization of most people. Differential flotation is no longer a ""delicate"" and unreliable process, but is now in wide use. Its ""safety"" is due to the wide use of chemicals which either depress or enhance floatability by definite modification of surfaces.The extent of the development and reliability of differential flotation methods any be emphasized by pointing out that there are now several customall-flotation"" plants in this country treating complex lead-zinc-iron ores from widely separated mines. While these ores differ in chemical composition and apparently in physical nature, the various ores treated in such a plant are passed through the same crushing and grinding equipment and through the same flotation machines and flow sheet with only slight changes, if any, in quantity and kind of chemicals and oils added.Some of the development in differential flotation is due to intelligent research on the part of well-trained chemists and metallurgists; much of It must be attributed to empirical testing.Much of the success in differential flotation is due to more care being given to constant conditions with regard to such factors as (1) fineness of grinding, (2) density of pulp entering flotation machines, (3) quantity and constancy of oils and chemicals added to the pulp, and (4) place of addition of reagents, and time of ""conditioning"" treatment of pulp with reagents."

Aug 1, 1925

By O. C. Blade

The oil fields of Arkansas, all situated in the southern part of the State, have played an important part in the development of petroleum production in the northern coastal plain region of the Mid-Continent area. From the first discovery of oil in southwest Ouachita County in 1920 to December 31, 1930, a total of 480,167,5604/ barrels of crude petroleum has been produced from' this region. Development of the Arkansas fields proceeded rapidly after 1920. The El Dorado field was discovered in Union County in 1921. Drilling in Ouachita County resulted in the discovery of the Smackover field in 1922 and subsequently in the development of the whole southern area. To November 31, 1939,459 / producing wells had been drilled in 25 fields, aggregating 53,7356 acres of proved territory in 6 counties. Peak annual production for the State was reached in 1925, when 80,823,7007/ barrels was produced, resulting largely from flush production from the Smakover field, which rose td an average of 444,9507 barrel daily during that year. During 1924, 1925, and 1926 Arkansas ranked fourth among the oil-producing

Jan 1, 1940

By Robert E. Wallhagen

This report describes the results of a four year investigation into improved face ventilation systems for underground coal mines. The objective was to experimentally determine configurations for a diffuser fan system and a water spray (spray fan) system which will provide a maximum reduction in face methane concentrations without causing an increase in methane concentrations at the operator's position. The experimental evaluation was performed in full scale mock-up mine entries, simulating continuous mining operations in both a six foot and four foot coal seam complete with normal ventilation, water sprays, and methane emission. A limited study was also performed to assess the effect of scrubber discharge location on methane concentrations in the face area. The results indicated that diffuser fan and spray fan systems that were designed to augment the natural airflow pattern in the entry could provide a factor of 3 to 5 reduction in average methane concentration at the face, compared to a mining machine with just conventional water sprays. The properly designed diffuser and spray fan systems also significantly reduced the total methane present in the entry. A properly designed dust scrubber discharge can reduce face methane levels by a factor of two.

Jan 1, 1977

By Grant R. Brown

This report presents the results of a study examining the relationship between supervisor characteristics and performance in underground coal mines, The specific objectives of the research include; document tasks performed by first-line supervisors during a normal shift; explain why supervisors carry out their duties as they do: identify salient characteristics of effective first-line supervisors; and formulate criteria for selecting and developing candidate supervisors. To accomplish the study objectives, on-site observation and data collection was carried out at 13 underground mines in Illinois, Ohio, and Pennsylvania. One hundred thirty-eight first-line supervisors were observed during a full work-shift and discussions with the supervisors and the mine superintendent were held during the course of the visit. The observational data from the study provide a detailed description of what supervisors to during their shift. The report begins with an introduction discussing the problem being studied and objectives of the research. The literature related to supervisor selection is then reviewed. The following section describes the research design including data collection procedures and statistical methodology used in the study. The next sections present the analysis of mine, section, crew, and supervisor characteristics. The report concludes with a discussion of the results of the study and recommendations concerning supervisor selection and development.

Jan 1, 1987

By G. L. Oldright

By means of a technique developed in cooperation with the Eagle-Picher Mining & Smelting Co. and outlined in the first report of this series (R. I. 4333 ), it was possible to take many thermocouple readings with base-metal couples at temperatures over 2300° F with unsupported protection tubes for over half the lengths of the Henryetta retorts. -This technique made it possible to avoid the use of the usual optical pyrometer, which gives temperatures dependent upon the luminosity of the flames, and which is not conveniently usable to read temperatures for the lengths of the retorts from the front of the furnace. The temperatures of the retorts themselves were necessary in order to set upper limits for safe operation; the lower limits of operating temperatures are set by the zinc content of the retort residues. The zinc content left in the retort residues for various sections of length also varies with retort temperatures rather than with flame temperatures. The variations in temperature along the retort can then be used as guides to distill more zinc from the residues, to avoid fluctuations in the rates ,of flow of zinc vapor into the condenser and to employ lower temperatures if such rates become high enough to cause losses of uncondensed zinc.

Jan 1, 1948

By M. J. Ferrante

Relative enthalpies of CuBr from 298.15 to 1,301 K were measured at the Bureau of Mines to provide thermodynamic data needed for the advancement of mineral technology. The temperatures of transition were measured by differential scanning calorimetry (DSC) and the standard enthalpies of transition[ (IlH~r) by drop calorimetry. The combined results gave reversible transitions at 657 K with llH~r= 1.10 kcal/mol, at 741 K with lm~r == 0.51 kcal/mol, and at 759 K with an enthalpy of fusion (AH~) of 1.22 kcal/moL ] An anomalous increase in heat capacity preceded the first crystal transition at 657 K. Tabulated values are listed for the standard relative enthalpy, heat capacity, entropy, and Gibbs energy function from 298.15 to 1,500 K. Standard relative enthalpies are also given in equation form and combined with thermodynamic data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1984