Search Documents

By W. E. Wallace, S. -G. Xing, M. J. Keane, J. C. Harrison

"SummaryDiesel-exhaust particles from two sources were dispersed in aqueous mixtures of dipalmitoyl phosphatidyl choline, a major component of pulmonary surfactant, and were tested for genotoxicity. Diesel samples from the same sources were extracted with dichloromethane and transferred into dimethyl sulfoxide and subjected to the same assays. Both types of extractions yielded similar results in both the Salmonella mutagenicity assay and the sister-chromatid exchange assay using V79 cells. After separation of the samples into supernatant and sediment fractions, the activity of both diesel samples was shown to reside exclusively in the supernatant fraction for the solvent-extracted samples, and exclusively in the sedimented fraction for surfactant dispersed samples. These findings indicate that genotoxic activity associated with diesel particles inhaled into the lung may be made bioavailable by virtue of the solubilization / dispersion properties of pulmonary surfactant components.While diesel engine emissions are associated primarily with transportation, they are also very common in the workplace. Estimates for the U.S. are that as many as 1.35 million workers in as many as 80 000 workplaces are exposed to the combustion products of diesel engines (NIOSH, 1988). These occupations include, but are not limited to mining, agriculture, motor vehicle maintenance, fork lift truck driving, truck driving, and tunnel and bridge operation."

Mar 1, 1992

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975

The research described in this report was conducted under a cooperative research agreement between the U.S Bureau of Mines Twin Cities Research Center (TCRC), Cleveland-Cliffs Inc. (CCI), and three operations in Northern Michigan managed by CCI: the Empire and Tilden surface taconite mining operations, and the Central Shops maintenance facility. All of these operations are in or near Ishpeming, MI. The Human Factors Research Group at TCRC is responsible for designing, planning, and conducting the research, and reporting on the findings. This project was carried out in order to investigate the high prevalence of back injuries being experienced by workers employed at the three CCI Northern Michigan sites, In an analysis of Company accident records for workers employed at these sites, it was determined that back injury problems confronting the CCI sites mirror those confronting the entire mining industry.

Jan 1, 1994

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By Ann G. Kim

Studies on the initiation and propagation of mine fires have dealt almost exclusively with coal. It has been assumed that the self-heating potential of carbonaceous shales and coal wastes is relatively low. However, in abandoned coal mines and waste banks, initiation and propagation of fires may be strongly dependent on the self-heating tendency of these materials. The purpose of this study was to compare the self-heating probability of carbonaceous shales and coal wastes to that of coals. This study utilized a modified differential thermal analysis method, in which the combustion furnace temperature was the reference to which the sample temperature was compared. Based on the distribution of the maximum temperature differential and the sample heating rate, a self-heating probability value (SHPV) was calculated that corresponded to observed self-heating behavior. In this study, several of the carbonaceous shales and one coal waste had relatively high SHPV. The SHPV did not correspond directly to heating values or to differences in sulfur concentration.

Jan 1, 2010

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By Madan M. Singh

The use of fluid jets for industrial purposes has received considerable attention in recent years. The convening of The First International Symposium on Jet Cutting Technology1 in April 1972 devoted solely to this subject probably heralds the coming of age of this new science. It is interesting to note the emphasis in the conference towards the cutting of rocks, minerals, and soils, indicating the attention being devoted to excavation and mining. The use of water streams for mining of minerals is not new. It is well over a century since its first application.2 But its use in coal mining has been somewhat restricted over the years. In the past 30 years the U.S.S.R. has successfully used water for coal extraction, and these techniques have been examined in 15 countries in recent years. In the United States research on various aspects of the method has been conducted for over 15 years,3 but success stories from the Soviet Union,4 JapanS and Canada6 in the last 5 years has spurred greater enthusiasm. IIT Research Institute has done pioneering work in the 7-12 13-15 area of water jetting for rock and coal breakage. It has just completed an experimental study involving mining of coal with a 50,000-psi and 100,000-psi jet in a stripping operation14 under the sponsorhip of the U. S. Bureau of Mines (Contract No. HOll1789). As a complementary program the Bureau initiated a project to design a water-jet coal-mining machine (Contract No. H0133119). IITRI was a successful bidder on this competitive procurement.

Jan 1, 1974

By James R. Boyle

The value of mineral production in-creased 13% in 1977. Nearly all commodities registered an increase in production and value, continuing a trend that started in 1976. In addition, practically all commodities registered an increase in unit value. Alabama led the Nation in the production of crushed marble, was second in bauxite and scrap mica third in kaolin and oyster shell, and fourth in bentonite, dimension marble, and fire clay.

Jan 1, 1981

By A. E. Lindquist

This Bureau of Mines publication identifies areas having sufficient coal reserves to support synthetic natural gas (SNG) development and summarizes those areas having the highest potential. Capital requirements, mining and coal cost factors, water availability, and coal-quality data pertinent to SNG production are presented. Evaluation of individual coal reserve blocks was based upon coal and water requirements of the Bureau of Mines Synthane coal gasification process.

Jan 1, 1977

By William L. Crentz

In a Nation-wide appraisal of coking-coal reserves and of the practicability of upgrading marginal deposits to metallurgical standards, this study of the preparation characteristics of the coals in Cambria County, Pa. , was undertaken. Over 90 percent of the coal remaining in Cambria Comity is found in the Upper Freeport, Lower Freeport, Upper Kittanning, and Lower Kittanning beds. The Middle Kittanning bed, although mined on a commercial scale in the past, is not an important bed now, as most of the remaining reserves are too thin to be mined over wide areas. For many years, Cambria County has been an important source of coal for industrial and metallurgical purposes. The) principal production comes from the Lower Kittanning bed, which accounts for almost .60 percent of the Cambria County coal output. Table 1 shows the county's coal production, by beds, during 1948.

Jan 1, 1950

This report describes the results of a program to design, procure, install, and evaluate a multi-channel underground telephone system of modern design in the Sunshine Silver Mine near Wallace, Idaho. Although the evaluation portion of the program was deleted, this report contains a cost benefit analysis for such a system using estimates of operational data for the Sunshine Mine. The results show a centrally switched telephone system of conventional design with ruggedized phone enclosures and special environmentally sealed dial pads to be the most economical.

Jan 1, 1982

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the fourth report of investigations dealing with the cooperative tests between the Bureau of Mines and industry on the use of electrolytic manganese in steelmaking. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steel 3/ the second with its use in acid electric steel practice, 4/ and the third with its use in low-carbon basic open-hearth steelmaking. 2/ A résumé of those investigations E7 appeared in the magazine STEEL. 5/ The present report deals with the use of electrolytic manganese in the manufacture of four types of stainless steel and the new Timken 16-25-6 alloy. The Bureau of Mines supplied The Timken Roller Bearing Co. with 62,000 pounds of electrolytic manganese for use in the tests.The electrolytic manganese was produced at the Bureau of Mines pilot plant, Boulder City, Nev., by the process developed by the Bureau and described in Bulletin 463, Operation of Electrolytic Manganese Pilot Plant, Boulder City, Nev., by J. H. Jacobs. J. W. Hunter, W. H. Yarroll, P. E. Churchward, R. G. Knickerbocker, R. W. Lewis, H.A. Heller, and J. H. Linck. The workcarried out under the direction of R. S. Dean, formerly assistant director, Bureau of Mines, and R. G. Knickerbocker, formerly chief, metallurgical branch, as part of a long-range program involving the development, manufacture, and use of manganese from domestic ores. Preliminary arrangements for the plant tests were made by the late A. A. Dow. 7/"

Jun 1, 1947

By William L. Crentz

Late in the nineteenth century en active coal-mining industry was begun in the Lower Freeport bed near Reynoldsville, Pa., where the bed thickened to more than 10 feet in places . The coal was readily accepted as an excellent steam fuel. Much of the thick coal his been depleted, but there are many areas where the deposit averages about 14 feet in thickness. As the more desirable mining sites were worked out in the Lower Freeport bed, other beds were exposed from which will come the county's major cowl production in future. The Lower Freeport bed is still the most important bed in Jefferson County from a production standpoint. The Lower Kittanning bed is second. Sporadic mining is being done in the Upper Freeport, Upper Kittanning, Middle Kittanning, Clarion, and Brookville beds. Strip mining has permitted recovery of much coal that could not be mined profitably by conventional underground methods.

Jan 1, 1953

By E. J. Kloos

One phase of the work of the Bureau of Mines in health and safety is promoting the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum-performance requirements for the approval of self-contained breathing apparatus (1),4/ gas masks (2), supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks) (3), dispersoid (dust, fume, and mist) respirators (4), and nonemergency gas respirators (chemical-cartridge respirators) (5). Approval tests of self-contained breathing apparatus are conducted by Health and Safety District B; approval tests of other types of respiratory-protective devices are conducted by the Branch of Health Research. Manufacturers of respiratory-protective devices may submit their equipment to the Bureau of Mines for approval under the requirements of these schedules. If the device, when tested by the Bureau, meets the schedule requirements, a certificate of approval will be granted, which not only states that the equipment has passed the schedule requirements but also gives information about the limitations of the device. If it is found at any time that approved devices do not meet the requirements of the pertinent schedule, the Bureau may rescind approval.

Jan 1, 1959

By A. C. Fieldner

The annual reports of the research and technologic investigations conducted by the Bureau of Mines on the occurrence, properties, mining preparation, and uses of coal, of which the present report is the seventh,4/ are intended to be brief summaries of progress. They are guides to the current work and publications of the Bureau but do not replace the more complete reports published by individuals and groups of workers on specific problems. The annual reports present the results of tests, often in advance of publication in other forms, but original contributions in research are reserved for initial publication by their authors. A survey of the accomplishments of the Bureau in research and technologic work on coal during the 5 year period 1935-40 has been made available in the form of a bibliography.5/ This supplements a similar bibliography on this subject that covers the first 25 years of the Bureau, 1910-35.6/

Jan 1, 1943

By Lewis M. McNay

The Bureau of Mines located and examined 292 burning coal refuse banks throughout the Nation's coal-producing regions in 1968. These coal waste fires, extending over 3,200 acres, produce poisonous, acrid gases and particulate matter that pose a threat to health and safety in the surrounding areas, damage vegetation, and cause the deterioration of nearby structures and buildings. Methods of extinguishing coal refuse fires are discussed, and an approach to eliminating future occurrences of these fires is presented.

Jan 1, 1971

By M. M. Fine

A process for simultaneously reducing and indurating iron are pellets was developed by Bureau of Mines laboratory research and confirmed on a continuous pilot plant basis. Moist iron are concentrate was balled, mixed with solid reductant, and heated at about 1,100° to 1,150° C. On a small scale, a variety of concentrates and fuels were utilized successfully. The pilot rotary kiln tests were limited to natural magnetite, synthetic magnetite, lignite, and anthracite. In both cases, partially reduced pellets with excellent physical properties were regularly produced with average analyses of at least 80 percent total iron and 60 percent or more metallic iron. These and other prereduced pellets were smelted in the Bureau's experimental blast furnace facility, Bruceton, Pa. With prereduced spheres comprising 85 percent of the burden, the coke rate was approximately half that with standard oxide pellets and production of hot metal was increased by 75 percent. Economic appraisal of the cost of making hot metal indicates that reduced pellets could be more profitable than any other iron raw material in both investment capital and daily cost of operation.

Jan 1, 1970

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire of the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire f the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940