Search Documents

By Harry H. Ku

In December 1975, a report entitled "An Evaluation of the Accuracy of the Coal Mine Dust Sampling Program Administered by the Department of Interior" [1] was prepared by the Analytical Chemistry Division of the National Bureau of Standards (NBS), in response to a request by Senator Harrison A. Williams. Chairman, Committee on Labor and Public Welfare. The report attempted to evaluate the adequacy of (1) the personal sampler unit used to measure the coal dust concentration in the mines, (2) the procedures used by the Department of Interior (DOI) to analyze the dust samples obtained from mine operators, and (3) any recent studies made by the Department or private industry concerning the coal dust sampling equipment. Recommendations in the report of NBS included continued research efforts by the appropriate organization to correct the personal sampler deficiencies and to consider the use of area or stationary samplers as a supplement to the personal samplers. Concurrent with the NBS report cited above, the General Accounting Office (GAO) also issued a report in December, 1975 [2], suggesting that improvements are still needed in coal mine dust sampling programs and procedures relating to penalty assessments and collections. Among recommendations made by GAO, the following paragraph specifically called for actions by the agencies involved:

Jan 1, 1979

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By Ross. C. Barkley

A computer program has been written to simulate ground vibrations induced by multiple-hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosives charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g. velocity, attenuation, pulse), or by backcalculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties are backcalculating individual pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shown to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included and additional verifications with field results are required.

Jan 1, 1983

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

By H. B. Hill

The Lake Creek gas-condensate field, Montgomery County, Tex., Was discovered early in 1941 by the Superior Oil Co. The field, shown in figure 1, is approximately 37 miles northwest of Houston, Tex., about 11 miles north of the Tomball, and 10 miles west of the Conroe oil fields. The field is on the downthrown side of a pronounced fault zone, and the general structure is anticlinal, with the long axis trending northeast and southwest. Production is obtained from multiple sandstone reservoirs in the Wilcox group of Eocene age between the approximate depths of 8,820 and 11,840 feet below the surface of the ground.

Jan 1, 1948

By G. F. Friel, J. C. Edwards

A series of seven underground-coal-mine fire experiments was conducted in the Safety Re-search Coal Mine at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. Coal and styrene-butadiene-rubber conveyor belting were burned upwind of two sensor stations, 18 m and 148 m from the fire source. Exhaust from a diesel locomotive flowed over the fire sources in six of the tests. Metal-oxide-semiconductor (MOS), CO, and optical-path-smoke sensors were positioned at both stations and found to be an optimum set of sensors for the fire discriminations. A representative set of 7,679 samples of CO data and data from the smoke and diesel-exhaust MOS sensors were used as inputs to train a neural network (NN). By testing 42,538 data samples from the seven experiments, all fires were detected by the NN within 9.67 min from the onset of significant changes in the MOS voltages without any false alarms.

By H. John Head, Fred N. Kissell

In This Chapter [Gas reports from around the world Regulations for gassy mines in the United States Differences between metal/nonmetal mines and coal mines Monitoring for methane and taking action Diluting methane with additional ventilation Eliminating ignition sources What experienced mine operators say about methane control and Looking for methane when starting a new mine or expanding an existing mine] This chapter gives guidelines for preventing methane gas explosions during metal and nonmetal mine development and subsequent production operations.3 Emphasis is placed on recognizing the differences between coal mines, where the potential for methane hazards is relatively well understood, and metal/nonmetal mines, where methane may accumulate unexpectedly. Also, interviews with experienced mine operators add much to a complete understanding of what must be done to address methane problems in metal/nonmetal mines. METHANE GAS IN METAL/NONMETAL MINES Gas reports from around the world. The presence of methane gas in metal/nonmetal mines around the world is more common than one might imagine [Edwards and Durucan 1991]. For example: • The former Soviet republics have occurrences of methane and hydrogen in apatite, gold, and diamond ores, where solid or liquid bitumen occurs in the rock. • Scandinavian iron ore deposits include methane and other hydrocarbons in boreholes that intersect pitch and asphalt within the deposits, and methane and nitrogen in boreholes and fissures in arsenic and sulfide ores.

Jan 6, 2006

By J. D. Davis

On May 15, 1936, Congress authorized the Bureau of Mines to conduct certain studies, experiments, and investigations of subbituminous coal and lignite .4/ Appropriations were made in July 1937, and since that date an active investigation has been underway to complete the provisions of the act. Part of the investigation has included a comprehensive survey of the known properties of the lower-rank non-coking coals, and provisions were made to obtain more data on certain varieties. In line with this plan, a typically subbituminous coal was selected for an extended series o tests in the standard Bureau of Mines-American Gas Association unit,5/ at the Central Experiment Station. This particular noncaking coal was the first one of its rank that ha& been tested in the apparatus; for this reason the results are of particular interest because the testing apparatus was originally designed for use in studying the coke- and gas-making properties of coking coals. The test as described below has been developed by the Bureau of Mines since 1927 through a cooperative agreement with the American Gas Association.6/ Ninety to 180 pounds of coal is heated in a circular retort, 13 to 18 inches in diameter, at wall. temperatures ranging from 540°C. to 1,110°C. in 100°C. steps. All products axe collected and measured; their physical and chemical properties axe then carefully determined to ascertain the gas- and coke-making properties of the coal.

Jan 1, 1939

By R. A. Cattell

Every finding of the year's work, obtained under stress to meet present objectives, contributed to postwar needs, because the very nature and constitution of petroleum and natural gas require that research be conducted along the same general lines whether the results are applied in peace or war. More than 40 reports were submitted to the Petroleum Administration for War and others concerned with (1) evaluation of crude oils to determine their content of aviation-gasoline base stock, (2) evaluation of base stocks for blending with high-octane, synthetically manufactured components, (3) analyses of naphthas to determine their content of various types of hydro-carbons, such as benzene and toluene, and (4) the improvement of quality of marginal base stocks to meet future requirements of aviation gasoline. This upgrading of marginal stocks is being attained by selective distillation and chemical and catalytic removal of sulfur compounds. Asphalts were studied with respect to the characteristics of their various constituents in order to compound them, in the same way that aviation fuels now are being "built" to meet exacting requirements. The work previously initiated to give the industry fundamental data on thermodynamics of hydrocarbons progressed satisfactorily, and the heats of combustion of 10 hydrocarbons in the lubricating oil -range of petroleum were determined. Thermodynamic data requiring highly specialized techniques are so broad in application that their commercial usefulness is not yet fully appreciated.

Jan 1, 1946

By E. P. Youngman

The Siamese mining lew, which is cited as "The Sian Mining Act, 2461 (1919)," was enacted February 14, B. E. 2461 (A. D. 1919), corresponding to the ninth year of His Majesty's reign. This act replaces the Sian Mining Act of 1901 and repeals all edicts, decrees, laws, rules, and local customs relating to mining the terms of which are inconsistent with the new law. It shall in- clude all subsequent alterations or additions, as well as all rules issued by the Minister (of Land and Agriculture) already in force or to be brought into force publication in the Government Gazette to be deemed sufficient notice of any modifications or alterations. (Art. 1, 2, 5, 83, and 85.) Legislation passed recently amending certain provisions of the mining law for the purpose of controlling the sale of minerals is the mining amendment act, B. E. 2474, given August 21, 1931 (7th year of the present reign), which repeals provisions of the mining act, B. 3. 2461, and also all rules and regula- tions relating to mining that are inconsistent with the amending ect. Under article 25 of the mining amendment act, B. E. 2474, ministeriel regulations (of the Minister of Agriculture) were issued August 21, 1931. Further recent legislation, brought about by the agreement of the Siamese Government to become a party to the international tin restriction scheme (inter- national tin pool), is the tin and tin ore restriction act (Siam), B. E. 2474, which came into force on September 1, 1921, its purpose being to suspend the

Mar 1, 1933

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1981 (October 1, 1980 - September 30, 1981) under its Minerals Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

By Oliver Bowles

Lime is of tremendous importance to modern industries. In agriculture it is regarded as essential to the continued fertility of many important regions; in building it is indispensable, and in the many ramifications of the chemical industries it is so necessary and so widely employed that it has been designated "the king of all the bases." Figure 1 shows a general view of a modern lime plant producing more than 500 tons of lime daily. In 1924 the production of lime was reported from nearly every State in the Union and amounted to more than 4,000,000 tons, valued at, nearly $40,000,000. For a production of that magnitude between 8,000,000 and 9,000,000 tons of limestone are required. The many problems involved in winning this great quantity of raw material from the natural rock and preparing it for the kilns have in the past received little attention from any governmental agency. Therefore, in compliance with a request from representatives of the National Lime Association in 1922, the Bureau of Mines began a study of problems in limestone quarrying in an effort to advance more economical methods of operation and the utilization of waste material. Field studies were made at many quarries, and the information thus compiled, besides data already at hand from work in other branches of the stone industries, were disseminated to operators in the form of mimeographed Reports of Investigations, eight of which were issued at intervals during 1922, 1923, and 1924. A questionnaire was appended to each report, and quarry operators were invited to contribute additional information obtained as a result of their actual experience and observation. Operators of lime plants have been cordial in their responses and have supplied the bureau with much valuable information. From the data thus obtained, supplemented by later field studies, the revised reports have been combined to form the major part of this bulletin, which is believed fairly to represent present knowledge on the subject of quarrying limestone for lime manufacture.

Jan 1, 1927

By Thomas Varley

[For a year or more, statements have appeared in the technical press, and Especially in various trade journals, indicating that valuable metals such as gold, silver, platinum, and other rare metals, have been found and also have been successfully extracted from oil shales. These reports stated tat decarbonization and special methods of chlorination treatment, leaching and subsequent Precipitation, also cyanidation followed by table concentration of the residues after cyanidation, all indicated that told ad silver and other metals could be, and were, successfully recovered. Such articles have caused much misunderstanding, and as the correctness of some re of the statements made in them were questioned by some of the technical journals and by various chemists and metallurgists, an investigation of the subject. was begun by the metallurgical division of the Bureau of Mines, in order, if possible, to determine to what extent, if any, metals of value do occur in oil shales, and if so, the feasibility of attempting their recovery by tie processes said to have been used for teat Purpose. Inasmuch as the Bureau's station at Salt Lake City is investigating the recovery of oil from oil shales, the investigation of too recovery of metals from oil shales was assigned to my direction as superintendent 'of that station. An agreement had been entered into with the owner of m extensive oil shale deposit in Wyoming whereby I would personally collect the samples' of shales for use in the investigation.]

Jan 1, 1922

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

In 2006, a total of 280 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 46.8% (n=131) of all metal mining operations. Other common types of metal mines were copper ore (n=34; 12.1%), and iron ore (n=33; 11.8%). ? Nevada had the largest number of metal mines (n=53; 18.9%), followed by Alaska (n=31; 11.1%).

Jan 1, 2008

By Richard Stayner

Suspended seats perform two functions: Reduce effect of occasional large bumps; Reduce more continuous vibration at a lower level. The former needs high damping. The latter needs low damping. For most mobile work machines the inevitable compromise is generally better than a simple cushion seat, because that amplifies vibration at around 4 Hz which is a sensitive frequency for human vertical WBV. Why have standard tests for seat suspensions? • Seat suspensions are non-linear so any measure of performance depends on operating conditions. For comparison these need to be defined. • Seat manufacturers need benchmarks for product development; • Machine makers choose dynamic characteristics appropriate to their products; • Occupational health specialists wish to control operator exposure to Standard tests should be representative, repeatable and reproducible. These requirements are reviewed in relation to the history of seat test standards and the current position. Current position and history The current position is that we have standard tests for seats for agricultural tractors, earthmoving machinery, industrial (fork-lift) trucks. These tests comprise measurement of vibration transmission and of the rate of damping. Current standards developed as the technology developed, starting around 1960: 1. Test on machine driven over standard surface1. 2. Test on shaker reproducing standard surface. 3. Shaker input replaced by representative spectrum2. 4. Human subject replaced by dynamic dummy. (Not yet settled). Are standard tests representative? The development process has gradually moved seat tests further from reality. 4 hr samples of work exposure suggest that seats do not on average provide large reductions of vertical WBV3. For specific magnitudes of vibration they can work well. For low vibration, performance is reduced by friction and for severe vibration by length of travel. Recent work has led to a new test to quantify how a suspension controls over-travel 9.

Jan 6, 2006

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By L. C. IlsLey

"The use of trailing cables on cutting machines, loading machines, and similar electrically operated apparatus is recognized as a necessary adjunct to the economical operation of such units. On the other hand, such cables because of their liability to failure from being run over by cars, locomotives, and other track-operated equipment offer one of the greatest hazards - indeed, probably the worst hazard - met with in the operation and maintenance of permissible equipment. Therefore, the Bureau of Mines is seeking ways of making the use of trailing cables less hazardous.Recently the bureau conducted an extensive investigation of both concentric and duplex rubber-sheathed trailing cables at the Pittsburgh Experiment Station. The results of this investigation were published in two reports.3 4In a larger part of portable motor operations in mines a double-conductor cable can be used. The investigation already mentioned indicated that it is feasible to construct a 2-conductor cable that will stand considerable abuse, such as being run over by loaded cars or light-weight locomotives without producing dangerous arcing in the cable either from grounds or short circuits. There are conditions where more than two conductors are necessary, and in such instances it will probably be necessary to use a cable less resistant to this kind of abuse.Schedule 2C, covering the tests of electric motored equipment, was approved February, 1930. This schedule provides for performance tests on trailing cables as follows;Trailing Cable Performance: The following performance test, optional with the manufacturer, is established for determining the suitability of trailing cables for use on permissible equipment. Trailing cables that pass this test will be especially recommended for this service.The cable will be placed across the two rails of a track and a 4-wheeled 7-ton car will be run over it 50 times. The speed of the car shall be approximately 3-1/2 miles per hour and potential shall be applied to the cable during tests. The cable will be shifted in position after each passage of the car thus giving 100 places over which two wheels have passed. To warrant special recommendation of the Bureau, a cable must neither become short-circuited nor grounded either to the rails or wheels in more than 10 per cent of the 100 places.The Bureau of Mines is prepared to conduct tests as outlined in the foregoing paragraphs to determine the suitability of trailing cables for use on permissible equipment. Application for such tests should be made to the Director, Bureau of Mines, Washington, D. C. Each application should be accompanied by a check for $25.00, made payable to the Treasurer of the United States, to cover the expense of conducting the test on a given size and make of cable."

Apr 1, 1930

By R. J. Hundhausen

The Shamrock copper-nickel mine in Jackson County, Oreg., was formerly a part of the Chisholm mercury property. In 1948 new owners advanced the old workings 40 feet to reveal encouraging widths of copper-nickel sulfide, ore on the Shamrock claim. When the owner's funds became exhausted, the Bureau of Mines carried on the development in 1949-50, completing 1,650 feet of bulldozing trenching, 396 feet of drifting, and 3,419 feet of diamond drilling. The Bureau's trenching disclosed a separate surface deposit 600 feet south of the mine deposit. This and the previously known deposit subsequently were diamond-drilled. The underground deposit has a known length of 100 feet, a dip length of. 100 feet and a width varying from 1 to 25 feet. The surface deposit is 200 feet long, 200 feet deep, and 5 to 38 feet wide. Neither deposit has been entirely delimited by development to date.

Jan 1, 1952