Search Documents

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By J. H. Welsh

This Bureau of Mines report presents guidelines to be considered in the design, installation, and operation of environmental mine monitoring systems in underground coal mines so as to enhance safety in the U.S. mining industry. A review of the current status of mine monitoring in the United States is also provided.

Jan 1, 1987

The strike of the Canadian asbestos miners entered its seventh month with increasing signs of early termination. Both unions are in the midst of heavy negotiations with management, and an optimistic industry source predicted that work would resume by October 1. Recession recovery in some segments of the asbestos manufacturing industry is being impeded by lack of fibers, CADMIUM - On September 9, St. Joe Minerals Corp. reduced the price of cadmium metal to $2.75 per pound. The producer price bad been uniformly quoted at $3.00 per pound since June 26, 1975. Subsequently, Amax, Inc. and National Zinc Co. reduced their prices to $2.50 per pound. By mid-September all five U.S. cadmium producers were marketing the metal at $2.50 per pound.

Jan 1, 1975

To reduce the respirable dust generated by auger-type continuous coal mining machines. The Approach: Use water sprays close to the cutting bits on the auger so that coal fragments are thoroughly wetted as they are formed to prevent dust dispersal into the ventilating air. How It Works: The "wet auger" system of dust control uses water sprays distributed on both shafts of auger type continuous miners. This approach has been tested underground by personnel of the Bureau's Twin Cities (Minn.) Mining Research Center on a Wilcox Mark 20 continuous miner, in a cost sharing contract with Buchanan & Sons Coal Company, Inc. Personnel of the Interior Department's Mining Enforcement and Safety Administration collected dust samples and analyzed the data. A test machine was fitted with six sprays on each auger (see Fig. 1). Water flow rates from 8 to 12 gpm at pressures from 90 to 120 psi, or about 8 gallons per ton of coal mined, were required. At these rates of water usage, mining personnel experienced no problems with work-

Jan 1, 1974

By W. M. Merritts

The control of coal dust created and released during the operation of continuous mining machines in bituminous-coal mines of the United States is a problem. The interest manifested in this problem indicates the seriousness of the hazards involved, particularly when the dust has not been abated at its source and has become air-borne. Officials of the Sunnyside No. 1 mine, Kaiser Steel Corp., were confronted with the problem of abating the coal dust created by operation of a recently installed continuous-mining machine, and they requested the aid of representatives of the Coal-Mine Inspection Branch, Bureau of Mines, United States Department of the Interior, in developing an effective method of allaying the coal dust at its source.

Jan 1, 1951

By Avery H. Reed

RECORD production of marble, kaolin, scrap mica, and talc high-lighted the mineral industry of Alabama in 1962. Among the States, Alabama ranked second in scrap mica, third in the production of bauxite and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing of coal and iron ore, and the manufacture of cement, which together comprised 73 percent of the total value of production, compared with 72 percent in 1961. Other important industries were the production of crude petroleum, and stone quarrying. Leading companies were Tennessee Coal & Iron, Southern Cement Co., Southeastern Electric Generating Co., Alabama By-Products Corp., and U.S. Pipe & Foundry Co.

Jan 1, 1963

By J. P. Powell

The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Mid continent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also. The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County, Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that could not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 1.36 million barrels of water had been injected.

Jan 1, 1953

By Donald P. Tuchman, Robert P. Vinson, Jon C. Volkwein

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized ?lter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM®). Standard ?berglass TEOM ?lters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel ?lter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon ?ber candidate ?lters left minimal residual ash and produced no signi?cant spectral interference. Avoiding titanium dioxide in all ?lter materials proved to be a key requirement. Fine quartz particulates were collected on prototype ?lters in a Marple chamber, either open-faced or through PDMs during test runs. The ?lters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to ?lter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in ?lter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM ?lters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7–10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM ?lters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

By Steven J. Page, John A. Organiscak

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grind ability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated with ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss(ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-m coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.

Jan 10, 1998

By Sean Gallagher, William S. Marras, Alan S. Litsky, Velimir Matkovic, Deborah Burr, John Landoll

Study Design. Survival analysis techniques were used to compare the fatigue failure responses of elderly motion segments to a middle-aged sample. Objectives. To compare fatigue life of a middle-aged sample of lumbosacral motion segments to a previously tested elderly cohort. An additional objective was to evaluate the influence of bone mineral content on cycles to failure. Summary of Background Data. A previous investiga¬tion evaluated fatigue failure responses of 36 elderly lumbosacral motion segments (average age, 81 ± 8 years) subjected to spinal loads estimated when lifting a 9-kg load in 3 torso flexion angles (0°, 22.5°, and 45°). Results demonstrated rapid fatigue failure with increased torso flexion; however, a key limitation of this study was the old age of the specimens. Methods. Each lumbosacral spine was dissected into 3 motion segments (L1-L2, L3-L4, and L5-S1). Motion segments within each spine were randomly assigned to a spinal loading condition corresponding to lifting 9 kg in 3 torso flexion angles (0°, 22.5°, or 45°). Motion segments were statically loaded and allowed to creep for 15 minutes, then cyclically loaded at 0.33 Hz. Fatigue life was taken as the number of cycles to failure (10 mm displacement after creep loading). Results. Compared with the older sample of spines, the middle-aged sample exhibited increased fatigue life (cycles to failure) in all the torso flexion conditions. Increased fatigue life of the middle-aged specimens was associated with the increased bone mineral content (BMC) in younger motion segments (mean ± SD, 30.7 11.1 g per motion segment vs. 27.8 ± 9.4 g). Increasing bone mineral content had a protective influence with each additional gram increasing survival times by approximately 12%. Conclusion. Younger motion segments survive considerably longer when exposed to similar spine loading conditions that simulate repetitive lifting in neutral and flexed torso postures, primarily associated with the increased bone mineral content possessed by younger motion segments. Cycles to failure of young specimens at 22.5° flexion were similar to that of older specimens at 0° flexion, and survivorship of young specimens at 45° flexion was similar to the older cohort at 22.5°. Key words: biomechanics, low back disorders, fatigue failure, age, motion segments, vertebral endplate fractures, torso flexion, lifting, bone mass. Low back disorders (LBDs) are a major cause of both short- and long-term occupational disability in the United States, and it is clear that workers in certain occupations are more susceptible to LBD.2-5 Specifically, epidemiologic studies have shown that jobs involving heavy physical demands such as construction,2,3 mining,2,4 and farming,5 engender increased risk of back pain. These occupations are thought to experience high LBD rates as a result of their extreme postural and manual lifting demands. Studies have shown that jobs involving significant lifting 6-9 and jobs that involve frequent bending10-12 are associated with increased LBD risk. Workers in the mining industry, in particular, often have to lift heavy materials in restricted workspaces that compel torso flexion. An understanding of the impact of repeated loading of the spine in flexion on fatigue failure of spinal tissues is thus a critical issue for our research agency, which is concerned with reducing the pain and disability associated with LBD in the mining industry. It is well accepted that loads experienced by the spine during manual lifting tasks are sufficient to cause fractures in the endplates of lumbar vertebrae, particularly on repeated loading. 13-15 Endplate fractures may not be painful in and of themselves 16; however, evidence suggests that the process of internal disc disruption and disc degeneration may be initiated via endplate fractures. 16,17 It has been shown that endplate damage will alter the distribution of stress in the disc, resulting in buckling of the lamellas of the internal anulus.17 Once this process has been initiated, repeated spine loading will cause additional disruption of the anular fibers, resulting in formation of significant fissures or tears. 11-21 If these tears occur near or extend close to the outer portions of the anulus, a wound healing process is initiated, which involves infiltration of mast cells, macrophages, and re¬lease of cytokines and growth factors. 21 The presence of these infiltrates has been strongly linked to discogenic low back pain. 21,22 Indeed, for patients experiencing chronic low back pain, the prevalence of internal disc disruption is at least 39%,19 which represents the most

By John R. Bartels

Remote operation of continuous mining machines has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory studied the workplace relationships between continuous miner operators and various tramming tasks of the equipment using motion capture data, operator response times, and field of view data to evaluate the factors influencing operator-machine struck-by events (contact with a solid object) in a virtual mine environment. It is not feasible (nor ethical) to use human subjects to directly evaluate factors that precipitate such injuries. However, use of motion analysis data and digital human models can facilitate analysis of struck-by accident risk by allowing investigators to manipulate factors that influence injury. Factors included in this study included machine speed, direction of escape, the direction the operator was facing relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck.

Jan 1, 2008

By Winton Gale, David Oyler, Jinsheng Chen, Christopher Mark

The National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tailgate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

By Neil J. Mansfield, Setsuo Maeda

The purpose of using experimental subjective and/or perception methods is: (a) to understand human subjective impressions of the physical characteristics of vibration; (b) to determine the relationship between the subjective perception of some aspect of the vibration and an evaluation index of the physical vibration characteristics; and (c) the establishment of target values for design of vibration environments in terms of human sensation of vibration characteristics. In order to understand the relationship between a physical measure of the mechanical vibration and the subjectively perceived aspect of the vibration environment, experimental methods shown in Table 1 have been used1. [ ] The constant measurement methods of Table 1 are mainly used for measurement of the threshold of human sense. The subjective scaling methods are mainly used for obtaining subjective (or proportional) scaling between the perceived quantity and physical quantity. In this review, the fundamental approach of experimental methods for obtaining the target values used in the design of vibration environments, and the different findings between the subjectively perceived methods for evaluating human response to vibration characteristics and the physical quantity of the vibration environment are summarized. Fundamentals of Subjective Scaling The relationship between the experimental psychological methods for providing target values in the design of the vibration environments and the physical quantities is illustrated in Fig. 1. Vehicle mechanical vibration can be characterized using many metrics, and these can be considered the ‘input’ to the human. In order to predict subjective responses to the vibration, it is necessary to link the characteristics of the source of vibration and human reactions, the ‘output’.

Jan 6, 2006

By D. A. Reynolds, J. D. Davis

"INTRODUDTION Investigations by the Bureau of Mines have shown that the carbonizing properties of splint and bright coals may differ greatly. In a study of 55 coal columns selected from representative coals of the Appalachian region, Sprunk and coworkers 10/ compared various chemical and physical properties of splint and associated bright coals. Carbonization tests in the Fischer retort at 932°F. (500°C.) showed that, except for bright coals of high oxygen content, the coke residue from bright coal was much more swollen and cellular than that from splint. ·with one exception, agglutinating values determined by the Bureau of Mines test, were lower for splint than for associated bright coal.Because sorting of coal in quantity is tedious and time-consuming, separate types have not been carbonized by the Bureau of Mines-American Gas Association (BM-AGA) test, which requires 85- to 200 pound charges. However, this method has been used to determine the carbonizing properties of samples 0f bed layers that are composed largely of either splint or bright coal.4/ In these earlier tests, which were made at high temperatures on layer samples from the Elkhorn bed, Letcher County, Ky., the splint coal yielded more coke than the bright coal, and this coke was slightly stronger than that from the bright coal. The cokes from samples with large proportions of bright coal were more cellular or porous, as were the low-temperature cokes obtained from carbonization of separated samples of bright coal in the Fischer retort."

Apr 1, 1944

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Arthur E. Wells

"The present and possible future commercial production of potash from various sources in the United Status is discussed below under the following heads:1. Potash from the saline lakes.(a) Nebraska lakes.(b) California lakes.(c) Other lakes.2. Potash as by-product from the cement kilns.3. Potash as by-product from the iron blast furnace.4. Potash from silicate rocks.(a) Feldspathic material.(b) Leucite rocks of Wyoming..(c) Sericite slates of Georgia.(d) Glauconite (greensand) of New Jersey.5. Potash from Alunite.6. Potash from organic sources other than kelp.7. Potash from kelp.In this discussion very little more than passing reference, if any, will be given to those projects which up to date have been developed only slightly, if at all, beyond the small scale laboratory stage, or for the development of which there appears to be very little financial and technical backing at the present time. Nether or not many of these proposed projects have merit can be determined only by an actual operating demonstration.Generally speaking, the potash industry of the United States has been hardly more than marking time since the armistice. This is, largely due to the fact that the consumers of potash have been expecting that heavy shipments of foreign potash to the United States would be resumed soon at somewhere near the pre-war prices, and they have not seen owing domestic potash at present prices for many months. The result has been that domestic producers have been unable to sell their product at even cost and many producers of potash have been obliged to close down. Thu Nebraska lake plants were closed down in February. The California saline plants were operating at below capacity, and the only large alunite plant is closed down. Even the cement plants have little or no inducements to recover the potash being lost in their waste gases and the production is very small at present.This condition will doubtless continue until a definite policy is decided upon as to the future importation of potash salts from Germany and. France. If unrestricted importation is allowed at prices even 50% greater than in 1913, only a very few, if any, of the domestic projects will be in position to compete with the foreign potash immediately, and the present industry will probably greatly decline with little or no prospect for a future resumption of the industry."

Aug 1, 1919

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930