Search Documents

By Charles Will Wright

This paper will be of interest to those who are actually developing a mineral prospect or planning to do so, as well as to investors who are considering the problem of financing the development of the prospect, so that they may know what the risks are and what capital expenditures are necessary before a prospect may become a mine. The term "prospect" used broadly, as it is in this paper, is defined as any property that has a mineral showing of sufficient interest to warrant development, irrespective of prior work, Such previous exploration, however, may be extensive and consist of several tunnels or adits connected by raises, or of shafts with several levels. There may also be a small mining and milling plant on the prospect which, because of the lack of capital for development or the lack of markets for the products, is now idle. Such prospects may warrant further capital investment for development work or for a mine plant to raise to the stage of profitable production.

Jan 1, 1935

By C. H. Johnson

This paper on the out-and-fill method of mining is one of a series on mining methods published by the United States Bureau of Mines. It has been compiled chiefly from recent publications of the bureau describing in detail mining methods and costs at various mines. Other sources of information were the technical press, the Transactions of the American Institute of Mining and Metallurgical Engineers, the Mines Haudbook, and company reports. References other than those mentioned in Table 1, which lists the mines entering into this discussion and gives general data regarding them, are given in the body of the paper. The authors wish to acknowledge the kind assistance of many operating officials, either through correspondence or in the course of numerous visits to their mines. DEFINITION OF CUT-AND-FILL STOPING The out-and-fill method of stoping is that method in which relatively small sections or slices are taken successively from the lower surface of a block of ground by open-stoping methods, the broken ore being removed and each section filled with waste material before the next is mined. This definition excludes shrinkage stoping, even with subsequent filling; it excludes square-set and fill methods; it excludes the Mitchell slice method, which may be classed as underhand square-setting; it excludes the systematic use of stull sets and filling, which is a variation of square-setting; it excludes any method involving the caving of the ore, walls, or overburden during the process of extraction, although caving may be allowed to take place when the waste fill is withdrawn for use in other stopes; and it excludes any open-stope method without filling. Through variations, which will be discussed later, the cut-and-fill method merges into shrinkage stoping, open stoping, or square-setting. The use of casual timber support, such as props, stulls, or timber cribs for holding up weak portions of the back does not constitute a change from cut-and-fill to square-set mining.

Jan 1, 1933

By E. D. Gardner

This paper on the square-set system of mining embodies the results of a special study of the subject made as a part of the Bureau of Mines general investigation of mining methods and costs. Data for the paper were gathered by the authors during visits to mines using square-set mining, from Information Circulars prepared by consulting engineers to the Bureau on mining methods at individual mines, and from articles in the technical press and the Transactions of the American Institute of Mining and Metallurgical Engineers. The square-set system of mining is very widely applied and is one of the oldest methods in use in the United States. It is mainly employed for extracting relatively high-grade ore in heavy ground. It is also useful in taking out pillars left in mining by other methods. It is used to some extent as an auxiliary method with many underground systems and as an alternate with cut-and-fill, shrinkage, and open-stope methods when heavy ground is encountered. In some cases as much as 50 per cent of the ore may be extracted by square-setting at mines listed as using some other method of mining. A large tonnage is mined yearly by square-setting, principally in the Western States.

Jan 1, 1933

By Manuel Gomez

This report presents prediction equations for 12 variables that are indicative of metallurgical coal quality. The variables include six for coke strength and six for carbonization product yields. All variables were predicted for coking coals having volatile matter contents from 16.3 to 42.1 percent, dry basis. The prediction equations, developed by mathematical-statistical techniques, were based on information from the proximate and ultimate analyses, the size consist, and the petrographic composition of bituminous coals carbonized in BM-AGA retorts at 800°, 900°, and 1,000° C. The equations were evaluated for validity with independent data derived from the 900° C carbonization of 33 binary blends of various coals and 22 binary blends of Pocahontas No. 3 low-volatile bituminous coal with 11 high-volatile bituminous coals. Results show that metallurgical coal quality can be predicted ahead of mining because data used to derive the prediction equations can be obtained at the time of exploration. Capability to forecast coal quality is useful in mine planning and should provide basic information for optimization of blending and crushing techniques and thus lead to the production of uniform coke.

Jan 1, 1970

By E. R. Palowitch

Two samples of the Lower Hartshorne (Spadra) bed were collected: A sample of the raw coal with the machine cuttings excluded, and a sample of the machine cuttings exclusively. Analysis of the 5-inch by 200-mesh size fraction of the raw coal, excluding machine cuttings, showed that a product meeting minimum quality specifications could be produced by washing at 1.60 specific gravity, yielding a theoretical 93.7 percent of clean coal. A negligible amount of near-gravity material at the separation gravity indicated an easy washing problem. The sample of machine cuttings had a maximum size of 2 inches and contained about 50 percent ash. Washability tests of the 2-inch by 200-mesh size fraction indicated that a theoretical yield of 30.0 percent of specification-grade coal could be achieved by washing at 1.49 specific gravity. As the machine cuttings represent an estimated 10 percent of the total coal mined, their inclusion in the mine output would increase the theoretical net yield of salable coal by only 3.7 percent. Because the machine cuttings contained a high percentage of sink 1.80 specific-gravity material, they had neither an effect on the separating gravity required to clean the raw coal nor on the difficulty of separation. Gabbing underground versus transporting the cut-tings to the surface for disposal or washing either separately or combined with the raw coal involves a number of practical, economic; and intangible factors; hence, no specific recommendations could be made. A discussion of some of the factors involved in dealing with a similar problem is given by Gandrud and Riley.4

Jan 1, 1962

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and, the results are described in this report.

Jan 1, 1983

By H. C. Fuller

This paper discusses 105 production runs at Boulder City, Nev., in which titanium metal was made in 200-pound batches. It describes the equipment and techniques used in preparing raw material, the reduction process, and the removal of the reaction mass from the reaction vessel. Also, some data on man-hour requirements are presented. The main emphasis was on producing ductile-grade titanium and developing a standard procedure for obtaining a consistently pure product. Some departures from techniques used before were found to be desirable. The most important of these was the use of a sealed room with a controlled dry atmosphere in which the reaction vessel was opened and the reaction mass removed. This minimized the moisture taken up by the magnesium chloride in the reaction mass, and it could be purified successfully by vacuum distillation. Using the dry room also made it possible to leave al-inch shell of the reaction material on the walls of the vessel, which lowered the iron contamination and eliminated the labor and time-consuming job of cleaning the vessel after each reduction. Another change was lowering of the temperature during reduction to 750° C. instead of 850° C. This was found to give good results more consistently. The first poke to break the crust during reduction was eliminated, as it was found to be unnecessary and only added more work and was another possible way of introducing air. A rotating feed arm was installed in the reaction vessel to distribute the titanium tetrachloride over a larger area and, thus, prevent local overheating. The process, conducted in a batchwise manner as described and followed by good purification and fusion, produces a metal adequate in quality for nearly all purposes.

Jan 1, 1952

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978

Improve the Bureau-developed system for locating and communicating with miners trapped underground following a mine disaster. Approach Include in the wireless system a portable second-generation transceiver that is more reliable, compact, easier to deploy and operate, and ruggedized to withstand a mine environment. How It Works In an emergency, the new transceiver is snapped onto a caplamp battery for power. (Normally the 1 1/2-pound transceiver is either carried by the miner or is strategically located in the mine.) Its antenna wire, coiled inside the transceiver container, is removed and deployed in a roughly square configuration around a coal pillar or on the mine floor. The antenna consists of 300 feet of lightweight wire, which provides a large magnetic moment while remaining intrinsically safe, The photograph shows the

Jan 1, 1981

By L. Nahai

THE OUTPUT ff the mineral industry in 1964 in both non-Communist and Communist Europe showed an upward trend for most countries in keeping with the higher index of overall industrial production. Comparable indexes of mineral industry production for non-Communist and Communist Europe (including the U.S.S.R. in Asia) are not available, primarily because the U.S.S.R. does not report details of its industrial production by industrial sectors. However, available data both in the form of index numbers on production published by the United Nations and based on data as reported to the United Nations by the various countries, and actual production data for selected major commodities published by the various European countries reflect generally expanded output by both the extractive sector and the processing sector of the mineral industry in most of the 26 nations of Europe.

Jan 1, 1966

By K. B. Nowels

"INTRODUCTION For the last several years the oil industry has been turning more and more toward conservation arid the study of related production problems. It is generally conceded that ultimate recovery is increased by holding the natural gas in thy sand which is net needed in lifting the oil. The retained gas lowers the viscosity and surface tension of the oil and helps flow the oil from the sand. Lewis states that ""while the operator can not control the original conditions of energy and resistance in the sand, he can partly control the efficiency of expulsion. As it is the energy contained in the compressed and absorbed gas rather than the oil that is exhausted, it is but logical to judge the efficiency of a producing method largely by the relative quantities of gas produced with each barrel of oil. If by a change in method the producer lessons the proportion of gas with each barrel of oil, he should increase the total recovery- of oil correspondingly, even if the rate of production is temporarily reduced somewhat.""The effect of ""pinching in"" or controlling the flow of oil wells in an effort to lessen the proportion of has never been definitely known. The general belief has been that ""pinching"" a flowing well causes the oil and gas volumes to be reduced proportionately, maintaining the same gas-oil ratio as before the reduction in flow was made. Studies of gas-oil ratios in many fields have shown that much gas has been wasted, insofar as its effectiveness in oil production is concerned. Swigart and Bopp carried."

Oct 1, 1927

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By Frank G. Miller

Controlling natural-water drives to effect efficient and economic production of petroleum, through wells, from reservoir sands and rocks is a problem of major importance in the oil-producing industry. Water-drive fields are characterized by large quantities of mobile water under high pressure immediately below the oil in the flanks or extraneous parts of reservoir formations, Hence, the water, which is in fluid connection with the oil and a source of a large proportion of the energy available for moving it, advances up-structure to replace it. This phenomenon of water moving crestward into the oil-bearing parts of the reservoir and replacing oil is termed edgewater encroachment. The mechanism by which oil is flushed out and continually replaced by water as the hydocarbon content of the field is depleted must be understood if natural-water drives arc to be used successfully to, induce efficient recovery of oil from its reservoir rocks. Until recently, the function of water in the production of oil has been somewhat obscure and was not given the consideration it deserved in early petroleum production-research programs because of the greater importance associated with and the effort devoted to investigations concerning the relations of natural gas to production of oil. Thus, with virtually no fundamental information at hand, it is not surprising that at first edgewater was considered a necessary evil, and the manner in which it was dealt with depended largely on the experience of the operators. During the intervening years, however, practical information on encroachment of edgewater in oil sands has been widely disseminated as a result of studies of oil-field depletion, and many theories pertaining to petroleum-reservoir energy and performance have been advanced; these theories necessarily included consideration of edgewater as an integral -art of the reservoir fluids and a source of energy for propelling hydrocarbon fluids through the reservoir and to the surface of the ground.

Jan 1, 1941

By Frank G. Miller

Controlling natural-water drives to effect efficient and economic production of petroleum, through wells, from reservoir sands and rocks is a problem of major importance in the oil-producing industry. Water-drive fields are characterized by large quantities of mobile water under high pressure immediately below the oil in the flanks or extraneous parts of reservoir formations. Hence, the water, which is in fluid connection with the oil and a source of a large proportion of the energy available for moving it, advances up-structure to replace it. This phenomenon of water moving crestward into the oil-bearing parts of the reservoir and replacing oil is termed edgewater encroachment. The mechanism by which oil is flushed out and continually replaced by water as the hydrocarbon content of the field is depleted must be understood if natural-water drives arc to be used successfully to, induce efficient recovery of oil from its reservoir rocks. Until recently, the function of water in the production of oil has been somewhat obscure and was not given the consideration it deserved in early petroleum production-research programs because of the greater importance associated with and the effort devoted to investigations concerning the relations of natural gas to production of oil. Thus, with virtually no fundamental information at hand, it is not surprising that at first edgewater was considered a necessary evil, and the manner in which it was dealt with depended largely on the experience of the operators. During the intervening years, however, .practical information on encroachment of edgewater in oil sands has been widely disseminated as a result of studies of oil-field depletion, and many theories pertaining to petroleum-reservoir energy and performance have been advanced; these theories necessarily included consideration of edgewater as an integral part of the reservoir fluids and a source of energy for propelling hydrocarbon fluids through the reservoir and to the surface of the ground.

Jan 1, 1941

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By Sidney Katell

This report, covering the period January 1966 through December 1966, is a continuation of a series that began with the publication of Information Circular 7516 in October 1944. It is the eighth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering.

Jan 1, 1967

By Maria I. De Rosa, Charles D. Litton

The National Institute for Occupational Safety and Health (NIOSH/PRL) conducted a series of large-scale experiments to evaluate the effectiveness of optical flame detectors, photoelectric smoke detectors, and combined ionization and photo­electric smoke detectors for rapidly detecting mining equipment cab fires. The detec­tor alarm times were then used to trigger the discharge of a fire inerting system inside the cab to suppress cab material fires. This paper discusses the types of fire detectors tested, the experiments that Were conducted, and the results that were obtained. Con-" elusions are that rapid detection of equipment cab fires can be achieved to trigger the discharge of a fire inerting system inside the cab to protect the operator in the cab.

By D. L. Pitt

This paper, describing the milling methods at the concentrator of the Premier Gold Mining Co., Ltd., Premier, B. C., Canada, is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States and Canada. ACKNOWLEDGMENTS The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by the engineering staff and accounting department of the Premier Gold Mining Co., Ltd., all of whom have assisted materially in gathering the data used.

Jan 1, 1933

By W. Hodge Caraway

This report presents the results of an evaluation of several indirect methods of measuring the water content of oil-reservoir rocks. The water content of oil-base cores is considered to be most nearly representative of the water content of the undisturbed petroleum reservoir and therefore, the direct method of measuring the volumes of water in cores cut in oil-base drilling fluid was adopted as a standard for comparison. The indirect methods evaluated included (1) displacement through a semipermeable membrane by air, (2) centrifuge, (3) evaporation, (4) mercury injection, (5) chloride dilution and (6) electric logs. Approximately 270 samples of cores from petroleum-reservoir rocks were used in the study. The cores, most of which were cut with oil-base mud in the hole, were taken from oilfields in California, Texas Gulf coast, Colorado, Oklahoma, and Alaska.

Jan 1, 1959