Search Documents

By J. C. Cawley, G. T. Homce, M. R. Yenchek, H. K. Sacks

As in many other industries, such as construction and agriculture, overhead electric power lines are a serious hazard at mining and mining-related operations. Even when excluding injuries that occur during electrical maintenance work, over one fourth of electrical fatalities in the mining industry are due to accidental overhead line contacts, and for each fatality nearly two serious non-fatal injuries occur due to such contacts. In incidents involving high-reaching mobile equipment, many of the victims touched the equipment after the fact, unaware that the machine frame had become energized by the line contact. MSHA data for accidents involving overhead power line contacts in the mining industry between 1980 and 1997 reveal that in 57% of the cases personnel were unaware of the accidental line contact until after one or more workers touched the equipment or a hoisted load and were injured. The situation is similar in the construction industry, where according to the National Institute for Occupational Safety and Health (NIOSH) data at least 20% of such victims are unaware of the line contact. This suggests that a device that alerts workers when a power line has been contacted could help prevent many of these injuries. Such a device would not prevent power line contacts, yet if widely employed could yield a significant reduction in the number of resulting injuries. Researchers at the NIOSH Pittsburgh Research Laboratory are attempting to develop such a device. The approach being investigated is based on measuring electric current flow to ground through a machine during a line contact. The specific technique being tested involves the diversion of some part of this current through a shunt cable mounted on board the machine, to provide a point at which to install a current sensor. Experiments thus far indicate that this approach is feasible. Ongoing research is better defining electric current flow through mobile equipment, refining techniques for measuring this current, and identifying factors that could limit the effectiveness of the proposed alarm.

By W. W. Adams, T. D. Lawrence

"The National Safety Competition conducted by the Bureau of Mines, United States Department of the Interior for the promotion of safety in mines and quarries, has just been closed for seventeenth consecutive year. Enrollment covered more plants than in any previous contest. Moreover, a larger volume of employment was represented than in the contests of previous years, and several new plants were enrolled for the first time. Six safety trophies are awarded annually in these competitions one to the leading plant in each of six groups. An anthracite, mine in Pennsylvania, a bituminous-coal mine in West Virginia, a metal mine in Tennessee, a nonmetal mine in Virginia an open-cut mine in Minnesota, and a quarry in Alabama won the 1941 trophies.To be eligible to win a trophy, a mine or quarry must have had at least least 25 men working under ground or in the pit for not loss than 100 days. The number of man-hours worked must total 30,000 or more. Mines or quarries having no accidents during the year are rated according to the number of man-hours worked. If there are no plants with accident-free records, the mines and quarries in each of the six groups are rated according to their accident-severity rates; the plant having, the lowest rate is declared the winner.The Sentinls of safety trophies presented to the winning mines and quarries in the six groups were donated by the Explosives Engineer magazine to promote safety in the mineral industry. They are held by the winning companies for 1 year or until won by other mines and quarries."

Jul 1, 1942

By Douglas F. Scott

Zinc, silver, copper, and tungsten are the principal minerals in Dardanelles RARE II area (No. 4982). Zinc with associated silver and copper occurs in a persistent shear zone in metasedimentary rocks and in a massive sulfide vein; tungsten occurs as disseminated scheelite in a tactite zone along a metasedimentary-intrusive rock contact. Since 1883, approximately 100 lode mining claims have been recorded, mainly it the eastern portion of area No. 4982 (fig. 1). Extensive workings on the Alhambra Prospect indicate past production; however, no records were found for the prospect. At the Alpine Mine, 500 tons of tungsten ore had been mined before 1943 (Hopson, 1943, p. 1) and possibly 1,000 tons of tungsten ore mined by 1947 (Benson, 194/, pp. 2).

Jan 1, 1982

By Chas. F. Jackson

This circular is an abstract of a manuscript-completed in August 1932, which cannot be published in its entirety due to lack of printing funds. It was originally planned to publish the manuscript as one of a series of bulletins dealing with the mining and milling of ores of the principal metals. Because of the common association of lead and zinc minerals in many ore deposits, and because a considerable proportion of the zinc produced in this country is obtained as a by-product of lead mining or vice versa, it seemed necessary to treat the mining and milling of lead and zinc ores in the same volume.

Jan 1, 1934

In 2005, a total of 263 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining commodity sector, comprising 1.8% of all mining operations. ? Gold mines comprised 46.0% (n=121) of all metal mining operations. Other common types of metal mines were iron ore (n=32; 12.2%), copper ore (n=31; 11.8%), and lead and/or zinc ore (n=16; 6.1%). ? Nevada had the largest number of metal mines (n=52; 19.8%), followed by Alaska (n=27; 10.3%).

Sep 1, 2008

By Steven W. Schmauch

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines Studied 25,340 acres of the 28,960-acre Twelve Mile Creek Wilderness Study Area (OR-003-162) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 30 miles northwest of McDermitt, NV. The area is underlain by thick sequences of rhyolite to with lesser amounts of andesite and basalt flows. Bureau of Mines personnel reviewed pertinent literature, mining records, and examined the study area for possible mineral resources in geologically favorable sites. There are no organized mining districts and no record of past or current mining activity. Based on sample results, published literature and field observations, there are no identified mineral resources.

Jan 1, 1987

By Forrest T. Moyer

All general measures of the safety record of the coal mining industry worsened appreciably in 1970. Injury experience for the year was 260 fatal and 11,552 nonfatal injuries at respective frequency rates of 1.00 and 44.40 per million man-hours of worktime. The fatality total was 57 higher and the rate of occurrence was 18 percent higher than the corresponding figures of 203 fatal injuries with a frequency rate of 0.85 in 1969. The worsened fatality record in 1970 resulted primarily from a major disaster (a single accident which results in the death of five men or more) on December 30, 1970, that killed 38 men. There were no major disasters in 1969. The total of 11,552 nonfatal injuries in 1970 was the highest annual total since 1960. It was 1,635 higher and the frequency rate was 6 percent higher than the corresponding totals for 1969 of 9,917 nonfatal injuries occurring at a rate of 41.76. The injury severity rate of 8,308 days lost or charged per million man-hours was 13 percent worse than that of 7,359 in 1969. Similarly, the average severity of 183 days lost or charged per injury in 1970 was 10 days or 6 percent higher than in 1969. Aggregate worktime of 260.2 million man-hours and production of 609.8 million tons in 1970 were, respectively, 10 and 7 percent higher than in 1969. An average of 144,480 men were at work on an average of 227 active days in 6,316 mines and 544 mechanical cleaning plants during 1970.

Jan 1, 1973

By Russell R. McLellan

Under the Heavy Metals Program, investigations were conducted at the old Badger dill placer mini in Nevada County California to collect data and information regarding drilling and sampling methods and deposit characteristics. The studies contributed to a team effort by five Bureau of Mines research groups to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California. This report describes the techniques used and the results obtained in the sampling and drilling stage of deposit delineation studies that were conducted by the Denver Mine Systems Engineering Group. Sampling included the collection and processing of 400 tons of largo and small volume samples from drill holes, underground workings, surface pits, and blast hole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicate that the bulk of the gold is within 40 foot of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of three types of truck-mounted drills including rotary, bucket and vibratory, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel.

Jan 1, 2012

By E. C. Lane

[This Is the ninth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the interior. The first report gave data on motor gasoline sold during the winter of 1935-36.3/ The Present report presents analytical data for 2,033 samples, representing the products of approximately 80 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data that were average by the Pacific Coast Technical Group before 'being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. The cumber of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, arc as follows: Regular price, 1,066 samples, 208 items, and 49 brands; premium price, 575 tamales, 154 items, and 38 brands; third-grade gasoline, 7;4 samples, 150 items, and 53 brands. The meanings of these terms as used in the surveys tar as follows: Sample: The individual supply of gasoline obtained at the filling station and analysed in the laboratory.]

Jan 1, 1940

By William G. Hedling

The operation of electric face equipment in underground coal mines has proven to be extremely hazardous to mining personnel, including equipment operators and others working in the vicinity of active equipment. Recent industrial engineering studies* of accidents and fatalities indicate that a major contributor to this hazardous situation is noncompliance with modern principles of human engineering, particularly lack of standardization of control configurations. Control configurations differ not only among different machine types, but also among the same machine types produced by different manufacturers. This lack of standardization can produce a high incidence of error in the operation of electric face equipment, thus creating a potential source of accidents. Other examples of non-compliance with human engineering principles are the widespread use of identical black, round control knobs (regardless of the function being performed), and the inappropriate location, spacing, and labeling of controls. Any or all of these factors may place the operator in a "negative transfer" situation, which means that control manipulations appropriate for one type of machine are different from (or even the reverse of) the control movements required to produce the same effect on other machine types. This situation increases the accident potential to the operator, as well as to others in the vicinity. Accident potential is further increased by circumstances which do not allow for large error tolerance-specifically, emergency procedures. Reports of accident statistics cite operator inexperience as a primary cause of most accidents involving underground electric face equipment. Several factors contribute to operator inexperience, including: 1. High personnel turnover 2. Employee absenteeism 3. Current union practice of bidding for jobs.

Jan 1, 1974

By D. V. Keller

Black lung disease, or paeumocomosis, is a serious health hazard for workers working in a coal mine. Though the exact cause of black lung disease is not known, it is certain that prolonged inhalation of fine coal particles, ever present in the mines, does give rise to black lung disease. For a long time, it also has been known that limestone applied to coal dust mine surfaces tends to hold down coal dust thus preventing it from refloating in the air of the coal mines. Since the humidity in the mines may be generally high, this also might be an important factor in the particular substrate system behavior. Fine solid particles stick to other particles and surfaces very indiscriminately. The term adhesion is used for the phenomenon of attachment of particles to surfaces whereas cohesion is used for the phenomenon of attachment of particles to each other. The measurement of the force of adhesion of coal particles to coal substrates presents a great problem, especially in the case of particles in the size range of a few microns. These micron sized particles are at the limit of the resolution of the optical microscope and therefore an electron microscope has to be used for this purpose. The forces of adhesion between these particles and substrate may be very strong and can exceed the weight of the particle by four to five orders of magnitude.

Jan 1, 1973

By G. W. Jones, R. E. Kennedy

"INTRODUCTION In the manufacture, storage, transportation, and use of combustible gases and vapors, explosion hazards, which at times may be present when air becomes mixed with the gases and vapors, become of primary importance. Such conditions are especially dangerous where large volumes of gaseous atmosphere are involved, because an explosion under such circumstances is capable of doing tremendous damage to both property and personnel.Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated, and published results dealing with, the explosibility of various types of combutible atmospheres. The explosion hazards of natural gases have received attention, and results giving the limits of inflammability and ignition temperatures in air have been determined and published. 4/ Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide. 5/Because of the increased demand for crude oil for war purposes, the application of secondary-recovery methods of stimulating oil production have received considerable attention during the last few years. The process consists in the injection of natural gas into partly depleted oil wells to cause the oil in the sands to flow into producing wells and so increase the amount of recoverable oil. 6/"

Feb 1, 1945

By McHenry Mosier

This paper describing mining practice at Morenci, Ariz., is one of a series of articles on mining method, and practice in the various mining districts in the United States. At present (1929) practically all the mineral production in the Morenci district is from the Humboldt mine of the Morenci Branch, Phelps Dodge Corporation. The mining method used is adapted to the type of ore body being exploited; it has been developed by adopting methods used elsewhere and making necessary changes to fit local conditions. Improvements in current practices are still being made.

Jan 1, 1929

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By Michael Mancuso

This report summarizes the problems of topsail handling as related to present requirements of law and current equipment availability. The most prevalent topsoiling systems are reviewed along with a listing of advantages/disadvantages and best features of each system. Seven mining regions are included, along with an analysis of prevailing land use, types of soils and attendant physical, chemical am biological characteristics. There are several probable areas of future research "lined which can benefit mining, minimize the social impact of mined lands and speed the return of mined lands to more productive long-term use.

Jan 1, 1981

By Alla D. Mah

THERMODYNAMIC data for manganese and its inorganic compounds have not been critically surveyed since the work of Maier (31) 3 in 1934. At that time data were lacking or inadequate for many of the important metallurgical compounds. Experimental work, conducted during the intervening years, has supplied so many new thermodynamic values that it is again desirable to examine the available data and compile them into a single publication for handy reference. This paper consists of three main sections. The first summarizes the basic metallurgical thermodynamic data for manganese and its compounds, including heat capacities, entropies, heat contents, temperatures and heats of phase changes, vapor pressures, and heats and free energies of formation. All data available to May 1959 have been considered. The second section contains heats, free energies, equilibrium pressures, and equilibrium constants of reactions of manganese compounds, with special emphasis on metallurgical reactions. The third section supplies basic thermodynamic data for other elements and compounds encountered in metallurgical reactions of manganese, thus making it possible for the reader to conduct thermodynamic calculations without recourse to other literature.

Jan 1, 1960