Search Documents

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

By Gene R. Reid

The contract objective is the development of an Automatic Fire Control System for Mobile Underground Metal Mining Equipment. The Phase I Report, which described the projected data handling plan, was published on July 24, 1975. The Phase II effort covered the period from July 24 through December 2 and accomplished the following objectives: ? Acquisition of data in accordance with the project data handling plan. Data were acquired through visits to twenty mine sites in ten states and Canada; visits to Bureau of Mines and MESA facilities; visits to mobile equipment manufacturers; and an extensive literature search. ? Analysis of accumulated data which provided the following specific types of design inputs: selection of the type of mobile underground equipment found to represent the greatest overall fire hazard; typical operating conditions for the vehicle; characteristics of the reported fire experiences; and performance, cost and maintenance factors affecting potential purchases of automatic fire control systems for underground mining equipment. ? Development of the AFCS design concept. Utilizing the data analysis results and considering the state-of-the-art of fire control system components, a recommended design concept was developed with particular emphasis placed on the need for a low cost and reliable system. Design trade-off studies are provided for the recommended system and for four alternate system concepts.

Jan 1, 1975

By Richard L. Fowler

Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the beam coverage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve a completely self-contained shuttle car system which responds to the existing mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to evaluate various guidance techniques during the feasibility study. Subsequent simulation runs were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing was performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated the predicted performance capability during underground face haulage tests. Dust did not impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance. Closed loop steering control with manual override is recommended for the lateral guidance system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.

Jan 1, 1973

By Gary J. Cwick

Mineral resources of the Rice Valley Wilderness Study Area (WSA), in the Mojave Desert of southeastern California, were investigated by the U.S. Bureau of Mines and U.S. Geological Survey during 1980. The study consisted of an examination of mines, prospects, and mineralized areas by the Bureau: of Mines and geological, geochemical, and geophysical investigations by the Geological Survey. Little indicated potential for the presence of mineral resources exists in the valley floor segment of the study area. The Big Maria Mountains section of the study area has some potential for mineral resource development. Decorative building stone from both bedded quartzite deposits and weathered limestone surface rubble (driftwood stone) has been produced from the Big Maria Mountains segment of the study area. Total production is unrecorded but probably small. A 700,000 ton (640,000 t) quartzite resource was inferred and 4,500 tons (4,100 t) of driftwood stone within the study area was estimated. A relatively pure limestone deposit inside the study area contains an inferred resource of 14 million tons (13 million t). One prospect suggests a potential for the presence of manganese resources although none were estimated. The likelihood of discovering oil, gas, coal, uranium or geothermal energy is low; potential sources are not known to exist.

Jan 1, 1982

By Donald O. Capstick

[ ]

Jan 1, 1983

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area or the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using ?big hole? drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in detail.

Jan 1, 1978

The XVIth International Conference on Coal Mine Safety Research was divided into eight half-day technical sessions. In accord with the established practice of these conferences, at each session, presentation of the papers was followed by a discussion period. Questions and comments submitted in writing to the session chairman were answered or discussed by the authors of the relevant papers or by their representatives. These discussions were tape-recorded in the original language of the speaker and subsequently translated into English when necessary. Questions to which no answer was available at the time and a few comments that exceeded the scope of the session have been omitted.

Jan 1, 1975

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

By Thomas A. Milne

As part of the broad program to improve the safety of underground coal mines, the Pittsburgh Mining and Safety Research Center sponsored several detailed studies on the inhibition of coal dust-air explosions. The present study was one of these. The goal of the research was to advance the development of improved coal-dust explosion inhibiting agents by determining, on a laboratory scale, the basic chemical processes involved in the inhibition of coal-dust flames by dry-powder agents. B. Our Approach Neither the basic molecular processes involved in coal combustion, nor the molecular mode of action of dry-powder agents, are known with certainty. Our approach, therefore, involved the direct determination, by sampling techniques, of species behavior in small, aerodynamically simple flames. To further aid in separating behavior of coal and dry-powder inhibitors, the latter were studied in CH4-air flames.

Jan 1, 1976

By K. L. Cashdollar, C. K. Man, J. R. Gibbins

Oxyfuel combustion is currently one of the principal technological options being considered for capturing carbon dioxide from pulverised coal power plants. In oxyfuel combustion, coal is burnt in a mixture of recycled flue gases and added oxygen instead of in air. In principle this yields a flue gas containing only carbon dioxide, water vapour and small amounts other impurities. Oxyfuel combustion is superficially similar to combustion in air, but there are inevitable differences. This paper describes ignition tests on pulverised coal suspensions using a suite of coals of different rank and from different countries of origin and over a range of oxygen and coal concentrations of interest for oxyfuel combustion. The ignition tests were carried out using the National Institute for Occupational Safety and Health (NIOSH) 20-litre explosion chamber. The purpose was to determine how easily the various coals ignite and burn in mixtures of O2 and CO2 compared to their combustion in air. The residual char volatile and ash contents for the ignition residues were measured using a thermogravimetric analyser (TGA), allowing Q factors (i.e., enhancement in apparent volatile yield due to higher heating rates and/or heterogeneous reactions) to be determined and compared. An ignition index has been derived from the explosion and char data. This index has been used to rank low volatile coals for ignition propensity in air. The results show that to obtain ignition and combustion comparable to that in air, the oxyfuel O2-CO2 gas mixture must contain over 30% O2. Keywords: CO2 capture, combustion, pyrolysis, oxyfuel.

By E. P. Carman

This: report gives data on the installation and operation of a packaged-unit heat-pump installation in a residence in McLean, Va., a suburb of Washington, D. C. The original equipment, installed in January 1947, was one of the first of 50 experimental Marvair units manufactured by the Muncie Gear Works, Inc., Muncie, Ind. The compressor unit of this installation was replaced by the company in September 1947, with a modified commercial model. The commercial unit and the original pump and fan accessories have been used as the sole means of heating (and cooling in summer! the. residence for the subsequent five winters and summers. The conclusions and data given herein, therefore, cover 6 winters sad 6 summers of heat pump operation, including 1 winter when temperatures averaged below normal for 2 months and the following summer when temperatures were above normal.

Jan 1, 1953

By D. A. Stanley

The Bureau of Mines conducted laboratory-scale experiments to determine whether or not surface waters with a high organic content could be purified sufficiently to be used to replace the natural high-quality deep well water currently being used in the silica flotation step of phosphate rock beneficiation. Waters abundant in organic matter were collected from two central Florida streams, flocculated with a cationic polyethylenimine polymer, and processed in a sand filter. This treatment removed most of the organic materials from the water. Untreated surface water, treated surface water, and distilled water were used to compare the flotation response of the acid insolubles in an amine flotation circuit. Surface water treated with PEI-1000 was shown to be as effective as distilled water for the acid-insoluble-flotation step. Flocculation and filtration can therefore produce water suitable for amine flotation of quartz, which would permit substitution of surface water for deep well water.

Jan 1, 1981

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist and in locating them quickly, with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of those jurisdictions or to contrast the varying provisions of many States upon a single subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although

Jan 1, 1943

By Joseph Blake Smith

Coal resource data from published sources and company files were used by the Bureau of Mines to determine the location and extent of strippable coal reserves in Wyoming. Total strippable reserves of 23 billion tons were estimated in seven major coal areas. Seven large strip mining operations were active in 1969, and their production totaled 45 million tons of coal. Cutoffs used to define strippable reserves were (1) minimum coalbed thicknesses of 5 feet; (2) overburden-to-coal ratios of less than 10 cubic yards of over- burden per ton of coal; and (3) total overburden thicknesses of less than 120 feet, except where reserves occur in multiple beds or a single thick bed. Tertiary rocks along margins of the Powder River basin contain most of the strippable coal reserves in Wyoming. The Wyodak beds, ranging in combined thickness from 30 to 1.30 feet, crop out on the east flank of the basin and contain an estimated 19 billion tons of strippable subbituminous C-rank coals under less than 200 feet of overburden. Partings between these beds total less than 60 feet. The 100- to 200-foot-thick. Healy bed on the western flank of the basin and the 35-foot-thick School and 20-foot-thick Badger beds on the south also contain large strippable reserves. Elsewhere in Wyoming, strippable reserves. Elsewhere in Wyoming, strippable deposits are subbituminous coal of Late Cretaceous and Tertiary ages, mostly in the Hanna and Great Divide basins in the south-central portion of the State and in the Kemmerer-Hamms Fork region in the southwestern corner.

Jan 1, 1972

By E. D. Eastman

The basic character of the free energy r data relating to water and the oxides of carbon makes it desirable that the most representative values that can be obtained should be constantly available. The calculations of Lewis and Randall3 retain much of their of original value, but appear to require some modification in the light of more recent work. This paper has been written to incorporate the newer information and to present some estimate of the reliability of the resulting figures. The data upon which the calculations are mainly based are, for these substances, the equilibrium constants of the various reactions involved. The original work relating to these equilibria has, been reviewed and, where possible, weighted to correspond with its probable reliability. The differences in the results of the present from the earlier calculations are partly the consequence of this appraisal and partly of the inclusion of more extensive data, as will be indicated in detail in the succeeding sections.

Jan 1, 1929

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By A. A. Cochran

The purpose of this Bureau of Mines research was to investigate the theoretical and practical aspects of using ionizing radiation to promote chemical reactions that are of interest to metallurgists, and to carry out a radiation study of a suitable reaction. The effect of 44,000 roentgens per hour of 120,000-volt X-rays on the chlorination of highly pure mixtures of rutile, carbon, and various catalysts at temperatures up to 540° C. is described. At these low temperatures, recoveries were very low; however, in the eight different systems studied, an increase in yield due to X-rays was statistically significant in two instances and was of borderline significance in a third instance. In the other five systems, the differences in yield were not significant. Impurities and added catalysts caused relatively large variations in the yield of TiC14 from the reaction. Although the catalysts employed were reported in the literature as positive catalysts for the reaction, most of them were negative catalysts for the highly pure system studied. With only one exception, each increase in the purity of the charge resulted in a decreased yield of TiCl4. The experimental results indicate that many substances catalyze the reaction studied and suggest that the differences in reactivity of the charge stocks may be due to their various contents of positive and negative catalysts.

Jan 1, 1962

By S. J. Gasior

A method for destroying the caking properties of bituminous coal was developed by the Bureau of Mines. Coal is treated in a fixed bed by heating through its plastic range under controlled temperatures in mildly oxidative atmospheres composed of inert gas and/or steam containing about 1 volume-percent oxygen. High-volatile A (hvab) and high-volatile B (hvbb) and low-volatile bituminous (lvb) coals in the size range 1/8 to 1-1/2 inches were successfully treated at 0 (atmospheric pressure) to 300 psig in static beds 6 to 18 inches deep. Conditions of treatment depended on the coal and ranged from 80 to 200 minutes at 350° to 510° C. Char produced in this manner from hvab coal was gasified with steam at 800° C and 100 psig in a fixed bed in one series of tests and in other tests was exposed to hydrogen in a dilute co current free-falling-bed system at 750° C and 3,000 psig without agglomerating.

Jan 1, 1965

By Oliver Bowles

ASBESTOS is a name applied to a group of naturally fibrous minerals. As indicated in a later section devoted to a detailed discussion of the early history of asbestos, the tern may be defined as a. fibrous form of serpentine or amphibole. It does not include fibrous forms of other minerals, such as wollastonite, nemalite (fibrous brucite), or the fibrous forms of calcite or gypsum. A material that has the characteristics of silk or cotton and at the same time will not burn is unique. Because it combines these qualities with other advantageous properties, asbestos has specialized uses for which no substitutes are yet available. Asbestos furnishes a major raw material for a great variety of essential products and their manufacture constitutes a vast industry. The United States leads all countries in the manufacture of asbestos products. The value of such commodities manufactured in 1952 exceeded $332 million. They are not only of vast importance to budding construction and industry but axe absolutely, essential to certain important fields of use, for example, steam packings and friction materials, such as brake-band linings on automobiles.

Jan 1, 1955

By Shouchen Dun, Zong-Ming Li

Manipulation of hand-held objects in 3D space is a complex task. Understanding how individual digits interact with a hand-held object provides helpful information for hand tool designers, researchers, clinicians, and occupational therapists. At the object-digit interface, the contact mechanics can be represented by three force and three torque components. Six-component force/torque transducers can register all the three forces and three torques at the digit-object interface, and therefore are advantageous in the study of manipulation mechanics. The large number of force and torque signals from multiple force/torque transducers are difficult to interpret and therefore making experimental research of manipulation a challenging task. The purpose of this study was to develop a 3D visualization tool for the investigation of the contact mechanics at the object-digit interfaces during manipulation tasks. Methods A 3D stick-figure hand model was created based on digitized 23 anatomical landmarks of the hand. Five miniature 6-component force/torque transducers (4 × Nano17 for the fingers, 1 × Mini40 for the thumb, ATI Industrial Automation, NC) were used to record force and torque data at the tips of individual digits. Thirty channels of force/torque signals from the transducers were collected by a 16-bit analogue-digital converter (PCI-6031, National Instrument, Austin, TX) installed in a computer. The transducers were mounted on a custom-made rectangular aluminum handle for object manipulation. Coordinate frames were established at each transducer, on the handle, and at the base of the MicroScribe digitizer. To visualize the force vectors at the digit-tips, the coordinates of the hand landmarks in the MicroScribe coordinate frame and the force vectors in local transducer coordinate frames were transformed to a common coordinate frame defined on the handle. One healthy right-handed, male subject participated in the experimental study. During the tests, the participant sat in a chair by a testing table. The forearm was strapped to an arm holder in neutral rotation position. The instrumented handle was fixed on the testing table by a C-clamp through an adapting plate. With the hand of the subject gripped on the instrumental handle, the landmarks of the instrumented handle and the transducers, as well as the anatomical landmarks of the hand were digitized using the MicroScribe digitizer for the purpose of coordinate frame establishment and transformation as described above. The subject performed three different maximum isometric voluntary contraction tasks: (1) grasping, (2) rotating in pronation, and (3) lifting. Results The 3D hand model and representative force vector clusters in a single trial of grasping, rotating, and lifting tasks are shown in Figure 1. Each cluster was formed by displaying all the 3D force vectors during the period of “stabilized” maximum effort in a trial. The magnitude and

Jan 6, 2006