Search Documents

By W. Beckering

IN CHARACTERIZING tars obtained by the low-temperature carbonization or North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite early it became evident in the tar-research program of the Bureau of Mines, U.S. Department of the Interior, that the small number of published spectra available for hydroxy aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was initiated as a continuing part of the tar program. As these spectra should be valuable to other investigators in this and related fields, they are being presented in this report. This group or spectra (figs. 1-98) represent 97 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Samples have been obtained from commercial and private laboratories or synthesized at the Bureau of Mines Lignite Experiment Station, Grand Forks, N. Dak.

Jan 1, 1959

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By W. W. Staley

This paper discusses the design of small head frames that will fill the needs of prospectors and small operators whose operations are conducted through shafts. The head frames considered were designed to handle relatively small tonnages. It was assumed that the shafts in which buckets are used would not exceed 300 feet in depth and that not over 60 tons of rock would be hoisted, in, 14 hours. In the design of the larger head frames, a hoisting capacity of about 250 tons per 6 hours from a depth of 300 to 500 feet was assumed. Under these conditions, hoisting speed, rate of acceleration, and weight of rope have a negligible effect on the head frame design and, therefore, have been ignored in the following, discussion. Because timber is relatively cheap and easily obtained in most mining areas, the discussion has been confined to timber construction.

Jan 1, 1937

By William M. Knuth

This study involved a review of bonding and bond release practices in the states of the Eastern and Midwestern Coal Provinces. Data was collected from regulatory authorities and site visits to document the bonding and release procedures in the states related to achieving successful reclamation. The regulations related to PL95-87 were reviewed. The analysis included suggested modified or new bond release criteria, a review of applicable bond release inspection techniques was prepared, a conceptual graduated bonding system and incentive procedures for reclamation of surface mine sites to alternative or higher land uses. A number of conclusions and recommendations for further research were included. A detailed bibliography and a glossary are included in the report.

Jan 1, 1978

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of a "line brattice air curtain" device under Bureau of Mines Contract H0357097. The purpose of this program was to develop the concept of using an air curtain for coursing ventilating air parallel with the air curtain From the last open crosscut to the face in exhausting ventilation systems to replace the line brattice cloth in room and pillar coal mining operations. The final design of the air curtain device consists of a 10-foot long closed end pipe with c: slot cut along its length. Pressurized air is delivered to the open end with a hydraulically-driven blower. A sheet of air emanates from the slot and is directed toward the mine roof. An invisible sheet of air is thus created between the top of the machine and mine roof and acts a an extension of the existing conventional line brattice.

Jan 1, 1977

By G. M. Kintz

The data in this circular were taken from publications of the United States Bureau of Mines and published annual reports of the Wyoming State Inspector of Coal Mines. The tables included are complete only' with regard to major disasters; the Bureau of Mines considers a major disaster one in which 5 or more men are killed. However, minor disasters and gas ignitions recorded in these publications are included. It is known that a number of gas ignitions have occurred of which no record is available. This is one of a series of papers by the Bureau of Mines giving by States available data regarding coal-mine explosions. This information is published in condensed form in the belief that it may be of vale to mine operators in preventing future coal-mine explosions.

Jan 1, 1934

By James W. Reil

A test series of small, precisely-controlled and thoroughly-monitored production blasts was conducted at two quarries. In each series, all variables except delay were kept constant, as much as practically possible. The first aim of the study was to determine the effect of local geology on ground vibration. The second aim was to test several hypotheses relating the effect of millisecond delay intervals to fragmentation and ground vibration. A resonant frequency of ground vibration was shown to be related to the thickness of the overburden, in accord with a model proposed by Gupta (1961). Since the overburden geology creating this resonant vibration cannot usually be changed, two methods were tested to choose delays such that blast vibrations would destructively interfere. These were shown to be effective in modifying both the peak particle velocity and response spectra of ground vibration. The delay interval chosen also affects fragmentation, primarily in massive rock, with an optimum relief between holes of 2 ms/ft. Strain gage records indicate a possible mechanism consistent with this information.

Jan 1, 1985

By Dana C. Reinke, David K. I Ingram

Researchers at the National Institute for Occupational Safety and Health partnered with the water well industry to develop engi­neering control technologies and training products to address noise exposure at the job site. Noise­induced hearing loss continues to be a problem in the well drilling industry. Research con­ducted by NIOSH found that air rotary drill rigs produce sound levels more than 90 dB(A) over the course of an eight­hour workday. Sounds levels above 90 dB(A), identified during hammer drilling and the hammering of casing, exposes workers to levels that can damage hearing. A typical air rotary drill rig provides no barrier, for noise and dust pro­tection, between the drill’s control panel and the drill stem. The development of a partial cab is the clearest example of NIOSH’s research partnership with the water well industry. NIOSH researchers determined that an engineering noise control to protect the oper­ator at the rig’s control panel would be effective, based on typical work site conditions. Many surface rigs do not have full cabs as a result of the original equipment manufacturer design or the high cost of aftermarket products. Developed as a partial cab, the NIOSH engineer­ing noise control design addressed stakeholders’ needs associated with cost, transport, and worker usage (Figure 1). Field tests found the partial cab effective in reducing sound levels at the rig’s control panel, a typical location for a drill rig operator. Sound levels at the control panel were reduced from 104 to 96 dB(A) (Figure 2). Coupled with continued use of personal protective equipment, such as hear­ing protection devices, the partial cab can help to reduce noise exposure. NIOSH researchers created a CD with informa­tion about noise exposure and the partial cab. Most important to well drilling companies is information on how to construct and attach the partial cab to drill rigs. The CD can be viewed on a standard computer and includes a video of the partial cab in use on a work site. Computer­aided design drawings are included on the CD and provide detail of the cab design as well as information on construction mate­rials and design details. Additionally, the CD provides background infor­mation on noise­induced hearing loss and hearing protection devices to increase knowledge about this occupational health concern. This information can be viewed by all company employees to help promote the partial cab’s importance to workers using the cab. More information on the partial cab noise control technology can be downloaded from www.cdc.gov/ niosh/mining NIOSH researchers also examined the health and safety training needs of workers in the ground water industry. It was quickly realized that most workers learn health and safety on the job and do not attend any sort of formal training. In addition, there is not a lot of time for daily “tailgate talks” or “shop talks” on health and safety issues. As a small business industry, the owner is often operating a drill rig along with his other employees. In general, new employees learn the job in an apprentice style sys­tem. As a result, workers and owners have few opportunities to access uniform health and safety information based upon the job — an outdoor work environment with daily change in work sites. With this information, NIOSH researchers devel­oped two products that deliver health and safety information to fit into the daily work of well drillers. Both are information circulars and are available through download at www.cdc.gov/niosh/mining and the NGWA Web site at www.ngwa.org/publication/ publications.cfm. These circulars are: Water Well Safety Bits. This booklet provides information in a “quick bites” style. It is pre­sented in a magazine format and can be left on

By T. A. Sullivan

Refining in a molten salt electrolyte was investigated as a means of recovering nickel containing less than 1 percent and preferably less than 0.2 percent cobalt from nickel products containing up to 5 percent cobalt. Electrolytic separation of nick and cobalt was accomplished in a molten KCl-LiCl-NiCl2 electrolyte. Nickel containing less than 0.10 percent cobalt was routinely prepared. Factors that influenced the transfer of cobalt to the refined product were the nickel concentration of the electrolyte, the cobalt concentration of the electrolyte, the ratio of nickel to cobalt in the electrolyte, and cathode current densities. A method of recovering the cobalt from the electrolyte was developed. The possibility of preparing high-purity nickel by this process was shown, as well as the preparation of various cobalt-nickel-tungsten alloys.

Jan 1, 1968

By Robert S. Sanford

Intensive investigations of domestic manganese deposits were conducted by the Bureau of Mines and the Geological Survey during the earlier part of the war minerals investigations when there was doubt that the quantity of manganese needed to produce the greatly increased tonnage of steel demanded for war supplies could' to obtained from its customary sources. Domestic deposits of ores that contain sufficient manganese for direct production of ferromanganese essential in steel Manufacture are generally small, and the bulk of the supply is imported. One of the few large deposits of low-grade manganese ore known in the United States is in the Artillery Peale district in southern Mohave County, Ariz. Manganiforous sediments underlie a very large area. Several large groups of claims, covering the most of the manganese-bearing ground, wore assembled in 1929 and 1930. The greater part of this area was leased by the M. A. Hanna Co. in 1937. Investigations by engineers and geologists for this company revealed that the average content of manganese is very low; but that the Maggio Canyon area, about 180 acres, contains higher-grade material. The company put down 28 vertical diamond-drill holds to explore this ground, under the direction of B. N. Wobbor, geologist.

Jan 1, 1948

By L. D. Schmidt, H. G. Graham

Several processes for the production of ultra-clean coal for electrode carbon were developed in Germany prior to and during World War II . These processes have been investigated since the end of the war by the British and U. S. Government missions . As the reports of the investigations are not readily available to the public , it is the purpose of this paper to present the information which has been obtained regarding the methods by which ultraclean coal was produced . Almost all the ultra-clean coal was used in the manufacture of electrodes for the production of aluminum and magnesium . Standard raw materials for making these electrodes are pitch coke and petroleum coke , which are nearly ashless . The inclusion of ash in the electrode carbon results in lowered efficiency and impure metal from the reduction process . Petroleum coke and pitch coke were in very short supply in Germany during the war , so that it was necessary to augment the supply with carbon produced from coal . In the emergency , methods were developed to clean coal which had never before been economically feasible . However , a demand for nearly ash-free coal might develop in the United States if a shortage of petroleum coke were to occur at the same time as a strong demand for light metals . Other uses of ultraclean coal are in direct hydrogenation of coal , in production of activated carbon, and for special fuels . Specifications for electrode carbon are rather severe owing to the necessity for producing pure metal . Maximum amounts of impurities allowable in American practice are as follows : Total ash , 1.0 percent ( in finished coke , 0.7 percent ) Silica , 0.08 percent Ca or Na, or their sum , 0.12 percent Sulfur , 2.0 percent Ba , Ni , Cr , Mn , Co , and V are objectionable in very small amounts . The most important process for ultra cleaning of coal in Germany was froth flotation . Froth flotation had been used widely there to process washery -water sludges and to recover coking coal from high - ash fines . Its use was indicated , therefore , when the demand for ultra low-ash coal arose . In two plants the coal cleaned by froth flotation was treated with acid or caustic to lower further the ash content . Another process used on an industrial scale was that of dissolving the coal substance in the middle oil from direct hydrogenation of coal under controlled pressure and temperature . The resulting paste was heated, filtered , and the oil distilled off . The residue was a low-ash organic material that could be carbonized for electrode carbon or could be hydrogenated directly . Several other processes had been developed to the laboratory or pilot - plant stage but had never been used on a commercial scale . These processes included cleaning by centrifugal action , cleaning by electrostatic action , and cleaning by forming a paste with oil in water . The coal-preparation plants at the Carl Alexander mine , Augusta Viktoria mine , and Kőenigin Elisabeth mine are described in Bureau of Mines Information Circular 7389 : " Coal Preparation Practice in Western Germany" , by Thomas . Fraser and M. G. Driessen . Most of the special equipment used at these plants is described in the above publication .

Oct 1, 1948

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

By R. A. Cattell

The conditions under which the researches of the Bureau of Mines on petroleum and natural gas were conducted in 1952 were little changed from those indicated in the last report,2/ which dealt with activities during 1951, immediately after crossing of the 38th Parallel by the North Korean Army. Although only a small part of the program was classified in the military sense, there was a feeling of the clash of world forces which called for even cheer scrutiny of the research problems so that the emphasis could be placed without delay where the greatest needs for na¬tional defense seemed to be. The reports of the work accomplished were so directed as to have the greatest immediate value to persons charged with supply planning for the military forces and included information on the availability and characteristics of a wide variety of crude oils, fuels, and other petroleum products. Actually, the approach, direction, and conduct of the work do not differ greatly under the two circumstances, as has been pointed out in earlier reports; only the tempo changes.

Jan 1, 1953

Reduce the cost of modifying uranium well casings so that leaching solutions can pass through, but sand grains are blocked. Approach The well casing and surrounding cement are perforated at the mineralized zone by impinging them with high pressure water jets. How It Works A nozzle assembly is attached to a high pressure (15,000 psi) pipe and lowered into the well casing which typically is schedule 40 PVC (poly-vinyl chloride). The high pressure pipe line is extended down Into the casing until it reaches the mineralized zone. The upper end of the pipeline is then connected by a high pressure hose to the outlet of a 10,000 psi pump. Turning the pump on for 5 seconds causes a high velocity water jet to cut through the well casing and the surrounding cement. Figure 1 shows a high pressure pipe being installed in a well casing. Cutting small diameter holes in the casing allows the leachant to enter the casing and be pumped to the surface. However, the holes are small enough to prevent most sand grains from entering. Numerous holes are usually cut through the casing. The 3-nozzle assembly shown in Figure 2 cuts three holes, one above another.

Jan 1, 1978

By Terry P. Medhurst, Stuart A. MacGregor, Peter J. Hatherly

In addition to fractures and joints, compositional factors and bedding influence the strength of clastic sedimentary rocks. Rock mass rating schemes must therefore consider all of these factors. In this paper, a rating scheme for clastic sediments based on geophysical measurements is described. Geo-physical logging allows an approximation of rock com-position to be obtained and an assessment of bedding frequency and laminations. Velocity measurements incorporate the effects of fracturing. The rating requires scores for the intact rock, bedding/cohesion, and defects. These are combined to yield a Geophysical Strata Rating (GSR). Determination of the GSR is objective and repeatable. GSR values are typically between 20 and 80 and can be related to the Coal Mine Roof Rating.

Jan 5, 2007

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsator-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig.5/ Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this type of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

Objective To develop safety training tools for mine health and safety trainers that fill gaps in currently available materials and help capture the wisdom and knowledge of “expert miners.” Background NIOSH began a series of stakeholder meetings in 1998 to determine what research was needed to improve miner health and safety. One of the more common concerns among stakeholders was a critical lack of appropriate training materials applicable to metal/nonmetal mining. Participants provided many insights into what effective training materials should include and how materials could best reach both new and experienced miners. The most important factors were that any materials be realistic and interesting and that some way must be found to capture the wisdom of expert miners before they retired. Approach NIOSH researchers chose videos as the best means of achieving these training goals. Over the past 3 years, NIOSH has produced three training videos that present information on safe work practices in underground mines: handling explosives, recognizing roof hazards and using proper scaling techniques, and installing ground supports. The last two videos, “Rock Falls—Preventing Rock Fall Injuries in Underground Mines” and “Miner Mike Saves the Day—or—Ground Support…It’s Important,” have won Alice Hamilton awards, NIOSH’s highest recognition of Excellence in Occupational Safety and Health, in the Educational Materials category. Two new videos are now being released. Both of these videos were shot completely in operating underground hard-rock mines and used expert miners to tell the story. Hazards In Motion The first, “Hazards in Motion,” deals with the dangers of working around mobile equipment in an underground mine. Ben, a new trainee, refuses to pay attention in his 40-hour New Miner Training class, and when the class takes its first trip underground, he wanders off and finds himself in many dangerous situations. He encounters many experienced miners who both chew him out for his unsafe attitude and give him advice and information on how to survive around mobile equipment. Many common pieces of equipment are shown, including haulage trucks, LHD=s, tracks and trains, slushers, skips and hoists, and air doors. The dangers of ignoring signals and of horseplay are also included. After nearly losing his life numerous times, Ben learns his lesson with the help of the Safety Angel, an experienced miner who looks suspiciously like his safety trainer. Ben’s Safety Angel saves his life repeatedly, teaches him how to work safely around these common conveyances, and introduces him to experts who have specific safety tips. Ben learns the error of his ways and vows to be the safest miner in the mine. “Hazards in Motion” is approximately 30 minutes long. Hidden Scars The second video is the first in the NIOSH “Expert Miner” series. “Hidden Scars” is a narrative interview with Don Capparelli, a miner and supervisor at the Sunshine Mine in north Idaho. This video captures the story of a fatal rock burst in May 1994, when Don was seriously injured and his long-time partner, Jimmy Findley, was killed. “Hidden Scars” is a very powerful story. Don Capparelli shares the physical and emotional pain he lives with daily as he relates the events leading up to the rock burst that took the life of his best friend and partner. This video is an excellent reminder of the human cost of uncontrolled accidents and the hidden scars that survivors must deal with for the rest of their lives. It runs approximately 25 minutes.

Jun 1, 2001

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

By E. L. Singleton

This Bureau of Mines investigation was initiated to study and establish some of the chemical and physical characteristics of the condensed Mno-Si02 system. To prevent oxidation of the manganous ion, I atmosphere of purified helium was used in the furnaces. Solidus-liquidus curves and invariant points were established from melting-point determinations and were supplemented from data obtained by the static-quenching method. Experimental findings and data are for the intermediate compounds of tephroite and rhodonite with their respective eutectics represented at 25.5 and 37.2 weight-percent silica. Tephroite melts congruently at 1,347° C., and rhodonite melts incongruently at 1,286° 8.. A metastable transformation was determined to exist at the 1,347° C. isotherm, the congruent melting point of tephroite. A composite X-ray-diffraction pattern was formulated for synthetic rhodonite. This investigation contributes fundamental data leading toward a better understanding of the more complex slag systems.

Jan 1, 1962