Search Documents

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau&apos;s Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By G. L. Oldright, Virgil Miller, F. K. Shelton, Keck. W. E., Horst Sieg

Potash is one of the principal foods and is necessary for the growth of most vegetables, grains, and fruits. For many years, this country depended entirely upon foreign sources for its supply of potassium compounds. However, during the last 15 years the domestic production of potash has gradually increased, as shown in table 1. 7/ Imports now supply only half of the American market. In 1936, the equivalent of 207,000 tons of K20 was imported, and 210,000 tons was produced domestically. In 1935, domestic consumption was approximately 420,000 tons of potash, a 57 percent increase over that for 1934 and surpassing previous peaks of 1928 and 1930.

Jun 1, 1937

By Fred Leonard

This report is principally concerned with the engineering and economic feasibility of area surface coal mining systems other than draglines. This analysis evaluates shovel/ trucks, shovel/crusher/conveyors, and shovel/rail excavation and haulage systems for an assortment of geologic environments and production rates in the Powder River Basin (PRB). Shovel/trucks, front-end loaders trucks, and shovel/crusher/conveyors were studied in a multi-seam, dipping geologic area of the Four Corners Region. The Texas lignite engineering and economic research involved bucket-wheel excavators (BWE), BWE/backhoes, and scraper/backhoe combinations for overburden and coal excavation. The PRB truck/shovel study utilized the most recent computer simulation available in both the design and cost analyses. Detailed engineering analysis, followed by in-depth operating costs (operating and depreciation), result in a complete evaluation of each mining system. Cost comparisons of the different mining systems under similar geologic and production constraints are presented in the report to illustrate the estimated capital investment and production costs per ton of coal and bank cubic yard of overburden.

Jan 1, 1980

By Andrew M. Leszcykowski

This report represents the first comprehensive accounting of lode mining sites in the Sheep Mountain mining district, Custer County, Idaho. Twenty-one mine and prospect locations have been added to the Bureau&apos;s Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were checked and the updated information added to the data base. The district&apos;s deposits are mainly confined to metasedimentary xenoliths in granodiorite and quartz monzonite. Those deposits in the north and west parts of the district are lead-silver-zinc replacement veins in dominantly calcareous facies; those in the southern part of the district are polymetallic fissure-veins containing pyrite, chalcopyrite, arsenopyrite, galena, and sphalerite hosted by micaceous schist and phyllite. The dominant structural trend in the southern part of the district is northwesterly and on strike with major deposits in the adjacent Seafoam mining district.

Jan 1, 1983

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner&apos;s susceptibility to to highwall hazards. First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change In coal seam inclination. Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in. diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, production to 500,000 ton/yr can be achieved. Volume II contains technical discussion of subsystems and machine drawings.

Jan 1, 1977

By F. S. Kendorski

This report presents the results of a program to improve, using existing and proven technology, unstable highwall conditions through better blasting practices in Appalachian strip coal mines. Better borehole blasting agent distribution and optimization of burden, spacing, and delay periods allowing satisfactory breakage with minimal backbreak were the objectives. At a selected field site, geologic conditions were closely examined with regard to joint orientation and spacing, and resulting slope stability considerations. A test series of eight blasts was completed and the resultant highwall monitored by repetitive photography. The study of drilling and blasting economics along with equipment performance led to an economic model of blast parameters and the identification of blast design cost benefits. The work demonstrated that small strip mining companies&apos; are able to achieve a more stable highwall excavation utilizing presently available technology, equipment, and explosive products at improved operational cost and safety.

Jan 1, 1981

By David D. Rabb

A report on location, sampling, assays, mineral examination, amenability leach tests, and evaluation of certain mine dumps in Mohave County, Arizona. Extractions of greater than 30 percent of the gold and silver were achieved during simulated heap leaching of selected mine dump material. Consumption of reagents was relatively low and results suggest leaching of prepared heaps is technically viable and could be economically attractive.

Jan 1, 1980

By Mark Sanders

This report compares a proposed 10/60 "piggyback" 02 generating self-rescue unit to the standard CO self-rescue unit with respect to work task interference. A simulated low seam coal mine was constructed and subjects performed locomotion, shoveling, cart pushing, and timbering tasks with the 10/60 or self-rescuer attached to their belts. Task completion time was longer on all tasks when wearing the 10/60 unit, although only locomotion was statistically significant. The 10/60 unit was bumped over 100% more often than the standard self-rescuer. Implications for design of the proposed 10/60 container are: 1) unit?s container must be extra durable to withstand the added abuse it is likely to receive by low coal miners; and 2) extra consideration must be given to preventing the device from slipping on the belt while working, especially in low coal.

Jan 1, 1980

By Tuncel M. Yegulalp

The objective of this study was to categorize mining operations in the stone, and sand and gravel industries into areas of similar ground control functions and define initial factors affecting operational safety in each area, by means of utilizing publicly available data, telephone interviews and on site observations. The findings and recommendations presented in this report are based on the information collected during the two phases of the project. They also contain, in part, the collective qualitative opinion of the operators with respect to government rules and regulations on ground control safety and the implementation of these rules and regulations by government inspectors.

Jan 1, 1981

By Anthony E. Szczuka

The purpose of this design note is to document the data that has been received from manufacturers, coal companies, training centers, government agencies, etc., that pertains to the completion of the Concept Feasibility Study For Training Equipment Designed to Improve Coal Productivity. Revision A documents additional data that has been received. ACKNOWLEDGEMENTS We wish to express our appreciation to the companies, mines, government agencies, unions, and contractor agencies listed herein that furnished the documented data. In most cases, it was furnished willingly and free of charge. In the few cases where the data was purchased, MDEC IRAD funds were used.

Jan 1, 1976

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By R. L. Mazza

This final report on methods of reducing and controlling methane in coal mine gob areas indicates that vertical degas holes are beneficial to the mines of northern West Virginia working the Pittsburgh Coal. The USBM funded project involved the drilling and testing of eight vertical holes (four over longwall panels and four over room and pillar panels) based on a review of 13 previously in existence. Areas of observation included gas production history, flow entry profile, underground methane reductions, strata separations, and casing loads (accompanying subsidence). Observations led to the drilling of successful holes drilled short of the mine. Eleven gas production response to applied vacuum tests were conducted at nine degas holes under the contract. Significant production responses were recorded over longwall gobs.

Jan 1, 1977

By M. O. Serbousek

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed an eight-piece precast reinforced concrete drift set for a small opening. Twenty-two sets of three different member sizes were tested to destruction under two loading conditions. A discussion of the test results and typical failure patterns is presented.

Jan 1, 1969

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young&apos;s, shear, and bulk moduli and Poisson&apos;s ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By M. M. Ayoub

This volume is the second of three volumes comprising the final report of the research project "Biomechanics of Low Coal." It covers only the anthropometric study of low coal miners. Volume I summarizes the overall biomechanical, anthropometry, and work physiology study conducted. Development of work clothes modified to meet the needs of low coal miners is described in Volume III. The male and female anthropometry, with the exception of weight and circumferential dimensions, was quite similar to the comparison populations. The miners tended to be heavier and have greater circumferences. The measurements made in this study were used to develop 5th, 50th and 95th percentile, quarter and half scale, male and female mannequins. These twelve mannequins can be used in work place and equipment design and redesign.

Jan 1, 1982

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

By J. H. Jacobs

This report records a chapter in the history of the development of an electrolytic manganese industry in the United States. Nearly all the manganese requirements of the United States have been imported. Although there are large quantities of manganese ore in the United States, most of it is low-grade and cannot be used for the production of ferromanganese. Since the electrolytic production of manganese carried out by a process developed in the laboratories of the Bureau of Mines offers a method whereby the extensive low-grade deposits may be utilized and since commercial development had proceeded slowly, the Bureau constructed a new and larger pilot plant at Boulder City, Nev., where abundant electric power was available. An authorization in November 1940 covered a plant of only several hundred pounds daily capacity. Additions to some sections author¬ized by subsequent appropriations have enabled the plant to produce over 2,000 pounds a day for extended periods.

Jan 1, 1946