Search Documents

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By G. W. Grove, E. E. Quenon

"INTRODUCTION During September, October, and November 1946 the Safety Division of the Bureau of Mines, off' the United States Department of the Interior, Pittsburgh, Pa., tested four new types of self-contained breathing apparatus and approved them in accordance with Schedule 13C. Approval was granted with the proviso that certain specifications outlined on the approval plate be made fully effective, and with the understanding that established safe practices in training in the care and use of self-contained breathing apparatus are of major importance.The excellent records made during the past 30 years in the safe use of self-contained breathing apparatus, some of which required the almost continuous wearing of apparatus during several hours daily for days, weeks, or months, may be attributed largely to the Bureau's system of rescue organizations, selection of physically fit rescue workers, effective training, and educational work done in rescue and recovery operations during fires or following disasters and in the care and use of self-contained breathing apparatus. Loss of life during wearing of breathing apparatus was due almost invariably to poorly assembled or otherwise defective apparatus, poor physical condition of the wearer, or insufficient training or some incorrect procedure.The newly developed breathing apparatus are of much simpler design than the conventional type used for the past several years; however, it is just as important to select rescue crews carefully and to train them properly in the care, use, and limitations of the new types of apparatus as for the older long-established types, if anything like safety is to be achieved in using them. The Bureau of Mines considers that 1/2-hour and 3/4-hour self-contained breathing apparatus should be used only as auxiliary equipment in mine rescue and recovery work, and their capabilities and limitations should be well understood by those who wear them."

Jul 1, 1947

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By G. F. Kuncir

The analysis summarized herein evaluates the Bureau of Mines Program for Advancing Mining Technology Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings, environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By F. S. Karn

Conditions necessary to obtain optimum yield of useful products when coal is rapidly heated to extreme temperatures by laser irradiation were determined by the Bureau of Mines. Product distribution and yield were investigated as functions of several variables. Low-rank coals with high-volatile matter gave highest total gas yields. Medium-rank coals gave the highest yields of H2 and CA and low-rank coals gave highest yields of CO and C02. Macerals gave gases of approximately the same composition, but the total gas yield increased in the order fusinite, micrinite, vitrinite, and exinite. Total gas and C2H2 yields varied inversely with particle size. The addition of nominally inert gases such as Ar, He, N2 increased yields of H2, C2H2, and total gas. Metals such as nickel and platinum had little influence on the rate of coal decomposition. Total gas yield increased with total energy of irradiation, and the ratio of C2H2-CH4 increased with concentration of energy. A study was also made of the irradiation temperature, and a material balance was calculated.

Jan 1, 1970

By A. F. Colombo

Bench-scale research was undertaken to determine if adding ammonia to cyanide leaching solutions would enhance the extraction of copper from an argillaceous Michigan copper ore. Two leaching techniques, (1) rolling using a tumbling bottle and (2) aerating using a modified Buchner funnel, and variations in pulp temperature; were employed in evaluating the effect of ammonia concentration on copper extraction. Under these experimental conditions, the extraction of copper was shown to be independent of ammonia concentration and entirely dependent on cyanide concentration.

Jan 1, 1968

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By William C. Cooley

This study Identifies and evaluates deposits of noncoal minerals in the U.S. which are most amenable to be mined underground hydraulically and transported hydraulically. A method was developed to screen and compare mineral deposits including economic comparisons. The most applicable minerals for hydraulic mining by borehole monitor jets from underground entries are soft uranium sandstones In Wyoming in locations where water is available. This method with hydrotransport could improve the safety, health and economy of underground uranium mining. Soft oil-bearing sandstones in California and Texas could be mined and transported by this method more safely than by other underground mining methods. Other weak sandstones may be hydraulically mined economically. Man, minerals are too hard to be mined by monitor jet but are amenable to hydraulic transport and hoisting. Uranium sandstone in New Mexico is of interest because of potentially improved health and safety in transport and lower transport cost, Increases in mine output for potash, in New Mexico and trona in Wyoming can be achieved most economically by adding hydraulic hoisting when existing skip capacity is at its limit. Research is recommended to obtain site-specific data on the feasibility of mining uranium ores by monitor jets.

Jan 1, 1981

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

By Kevin M. Connor, O&apos

This report documents-the process of literature review, site selection, instrument installation, data acquisition, and preliminary data reduction performed to evaluate the influence of rock mass discontinuities on coal mine subsidence. A system of surface, subsurface and mine level instrumentation was installed at the Armco No. 7 Mine in Montcoal, West Virginia where the overburden varied in thickness from 630 to 1040 feet. Survey monuments, borehole pressure cells, full profile borehole inclinometer-extensometers, mine level extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. Final design of the instrumentation system was based on: a) review of available information, b) field mapping and analysis of areal photography, c) drilling, and d) borehole geophysics. The report contains the complete graphed data of stress and displacements accompanying the longwall mining of a 4800 ft long by 480 ft wide coal panel.

Jan 1, 1983

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

Alumina can be recovered from clay , using 30 percent nitric acid for digestion . Calcined clay is crushed and then digested at 325 ° F and 85 psig pressure with less than stoichiometric nitric acid required to form normal aluminum nitrate . In this way , a solution containing both normal aluminum nitrate , Al ( NO3 ) 3 , and basic aluminum nitrate , assumed to be Al ( OH ) ( NO3 ) 2 , is formed , and in which iron is virtually insoluble . The solution is filtered and then concentrated in vacuum evaporators to crystallize normal aluminum nonahydrate . The crystals are washed with 50 percent nitric acid and then decomposed to alumina and nitrogen oxides . The design that has been developed for this process is based on published work . For a plant producing 1,000 tons of alumina a day , the estimated operating cost is $60.69 per ton of alumina , and the estimated fixed capital cost is $ 76 million using a Marshall and Stevens chemical equipment index basis of 240.0 . This process is not competitive under current economic conditions with the production of alumina from bauxite via the Bayer process . For lowering costs , future research should include study of leaching at lower temperatures under atmospheric pressure and alternate aluminum nitrate decomposition methods .

Jan 1, 1964

By Gordon R. Sima

This contract is concerned with the construction of a Time Resolved Audio Dosimeter System consisting of one readout unit and several dosimeter units. The Time Resolved Audio Dosimeter System was designed and developed by the Bureau of Mines with the purpose of this contract aimed at obtaining additional units for further field testing and evaluation. All construction was in accordance with the Bureau of Mines design and/or Bureau approved drawings produced during the course of this contract. This report contains a summary of the construction efforts, problems encountered, recommendations and all drawings produced under this contract.

Jan 1, 1977

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

By D. Harrington

Ventilation of underground workings consists of establishment of such control of air currents that the underground workers may work in safety, with maximum comfort and efficiency, mad without impairment of health; and that the mine openings may be made subject to such control of air flow as to remove from the workings at ordinary times harmful gases and dusts, and at time of emergency, such as fire or explosion, there may be maintained as much or as little air flow as may be desired covering portions of the mine or the mine in its entirety. Control of air flow is the keystone of any ventilating structure, and this very essential feature is obtainable only by the installation of mechanically operated fans, to ether with other ventilating devices such as doors, overcasts, regulators, etc. Every mine, large or shall, coal or metal, should from the outset be equipped with a fan. While much has been written about natural ventilation and many claims have been made that in specific mines there is sufficient natural al" flow, there are few if any mines, coal or metal, where natural ventilation supplies anything like adequately safe or healthful conditions for underground workers even at ordinary times; and at a time of mine fire or explosion the mines depending upon natural ventilation are practically helpless, and certainly are decidedly dangerous to those unfortunates forced to be in them.

Jan 1, 1933

By Terry R. Neumann

The Olallie RARE II study area has volcanic cinder deposits with a sow potential for development. No mining claims or prospects are known within the study area, and except for common construction materials such as volcanic cinders and stone, no mineral deposits were identified. An evaluation of the geology indicates that metallic mineral deposits are unlikely to exist. No significant metallic concentrations were reported in samples from the area. The only resources in the study area are about 30 million cu yds (23 million cu m) of cinders in three cones. The cinder deposits in the study area cannot compete economically with enormous deposits of similar material in more accesible areas closer to markets. At the present rate of consumption, resources outside the area are adequate far into the future. The geothermal potential of the study area is being evaluated by the U.S. Geological Survey.

Jan 1, 1983

By John M. Gomes

The preparation of tungsten carbide by molten-salt electrolysis was investigated. Sodium tungstate in the electrolyte and carbon from the graphite anode were the source materials, Optimum results were obtained with an electrolyte consisting of 83 mole-percent sodium chloride and 5.7 mole-percent each of sodium tungstate, sodium metaborate, and sodium hydroxide; a temperature of 1,000° to 1,025° C; an anode current density of 37 amp/dm2 or less; and an initial cathode current density of 150 amp/dm2. The yield was approximately 0.45 g/amp hr. The electrolytic tungsten carbide product contained approximately 5.4 weight-percent combined carbon as compared to 6.1 weight-percent for pure tungsten carbide. Microhardness of the electrolytic tungsten carbide, determined with a 50-gram load, varied from 3,480 to 3,970 dph. The material was friable and could be ground in a laboratory ball mill to less than 400-mesh particle size.

Jan 1, 1969

By F. D. Sutterfield

This study was conducted to provide experimental evidence on the effect of modifications of gasoline front-end composition on the photochemical specific reactivities of automotive emissions. Evaporative and evaporative-plus-exhaust emissions from an automobile operated with four fuels of different volatility and varying levels of C.-C5 olefins were irradiated in a 10040 environmental chamber at three sets of initial hydrocarbon-nitrogen oxides concentrations. Reactivity was measured and expressed in terms of rate-of-NO2 formation and dosages of oxidant, peroxyacetyl nitrate, and formaldehyde. The compositional changes that were necessary in reducing fuel volatility were found to have no significant effect on the reactivity of the emissions. However, replacing C4-C5 olefins with saturated components resulted in sharp decreases in all reactivity manifestations observed for the evaporative emission samples. A lesser influence (of C4-C5 olefin replacement) was found with the composite exhaust-plus-evaporative samples; the effect that was observed could be attributed to the evaporative emission portion of the sample. The data therefore suggest that saturation of front-end fuel olefins had no large effect on exhaust emission reactivity.

Jan 1, 1971

This study of underground mine water inflow was initiated by the U. S. Bureau of Mines in March 1980. The objective of this study is to evaluate the hydrologic variables associated with surface water and ground water systems that affect the inflow of ground water into an underground mine. Data collection techniques are reviewed for their applicability for quantifying these hydrologic variables. Innovative techniques are also investigated. Existing analytical and numerical procedures for predicting underground mine water inflow are reviewed and evaluated. Over 300 computer models were reviewed for their applicability to modeling underground mine water inflow. The model UNSAT2 is utilized for modeling inflow to a shaft and tunnel or drift. This model and the techniques developed in this study are applied to two existing mines.

Jan 1, 1982

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at 'any of several stages of extraction and processing, the stage of measurement used In this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the product of auxiliary processing at or near the mines.

Jan 1, 1977