Search Documents

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Weiying Zeng, Shouwei Wang, Jinbei Zhong, Xiangdong Meng, Lingtian Meng

"Due to a drainage problem, the Lanzhou to Chongqing high-speed rail line had been out of service during the 2015 wet season, so a drainage tunnel is to be constructed for the line and required to be accomplished before the 2016 wet season. This drainage tunnel is only 5 meters below the line which is in service, therefore blasting vibration needs to be strictly controlled. This paper introduces all theapplied blasting methods, parameters and detonation throughout the entire project, finally bringing in the electronic detonator stagger phase technique and corresponding time difference for detonation."

Jan 1, 2017

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By Lon Santis

This paper analyzes 110 serious accidents that occurred during the use of commercial explosives in mining, construction, and other industries since 1992. Data from the Mine Safety and Health Administration (MSHA), the Institute of Makers of Explosives (IME) members’ reports, and media reports were used. Only accidents that resulted in a fatality, significant lost work time, or injury to the public were considered in this analysis. The accident data were analyzed for trends in frequency, type of industry, cause, type of individual harmed, and geographical region. Although the data showed that explosives accidents are decreasing in frequency, still, 29 people were killed and 134 injured. Eightyfive of the accidents occurred in mining, 17 occurred in construction, and 8 occurred in other industries including oil recovery, seismic exploration, agriculture, logging, boiler cleaning, and avalanche blasting. As other studies have shown, flyrock and failure of blast area security caused over half of the accidents. Mishandling, misfires, or fumes caused just over one-third of the accidents. Lightning and drilling into explosives were responsible for the remainder of accidents.

Jan 1, 2003

By D E. Shaw, J B. Case, J Gusek

Explosive casting of overburden is defined as the use of explosives in blasting to move overburden to a spoil pile without rehandling. Studies of the economic feasibility of the method, and the formulation of a design hypothesis involving rock properties, and blasthole geometry are presented. These studies indicate that if technical feasibility can be demonstrated to increase surface coal production, considerable economic advantage would accrue to coal mine operators.

Jan 1, 1980

By Alastair Torrance, Gary Cavanough

Approximately 1.5 million tonnes of ammonium nitrate are transported annually across Queensland, Australia—equivalent to nearly 100 truckloads per day. This is in the form of both AN prill and ammonium nitrate based emulsions (ANE). In a recent incident, a collision involving an ANE tanker resulted in a detonation that caused extensive blast-related damage and led to the closure of a major highway. Had this event occurred within a populated area, the consequences would have been catastrophic. For over a century, investigations into the causes of such spontaneous detonations have been inconclusive. A recently completed industry supported research project has made a pivotal discovery: a surface reaction mechanism leading to hydrogen generation has been identified as a precursor to detonation. If sufficient hydrogen accumulates and subsequently ignites, it can release enough energy to initiate the detonation of bulk ammonium nitrate and ANE. Controlled experiments conducted during the project successfully demonstrated hydrogen-driven detonation events. Previous work by Proulx and Scovira, presented at the 2000 ISEE Conference, described spontaneous detonations in hot, reactive ground and the mitigating effects of buffered emulsions and ANFO. Building upon their observations, this study reproduces similar incidents under laboratory conditions, confirming that hydrogen generation also results from reactive ground interactions. Importantly, the findings challenge traditional assumptions, demonstrating that ammonium nitrate and ANE detonation in reactive environments does not require an ignition temperature threshold, confinement, or a classical chemical decomposition pathway.

Jan 26, 2026

By John L. Didlinger

We all hate the paper work in keeping accurate blasting records. Nevertheless, have you ever thought what those records could show you? Think about it. Those records could show you vibrations, noise, and safety problems. They could show you the ratio of powder used and tons produced, the cost per foot, even help negotiations for pricing.

Jan 1, 1997

By Joe Atalla, Jesse Desrochers, Rodrigo Hayashida, Joseph Mukendi Kabuya

The Mont-Wright mine stands as a prominent open-pit operation in Canada, renowned for its vast iron-ore reserves. However, the efficacy of its blasting operations, crucial for efficient production, has encountered challenges due to the diverse lithological compositions across multiple pits. This study presents a comprehensive approach to optimize blasting practices at Mont-Wright mine, tailored to the specific lithological characteristics of each rock domain. Through systematic analysis and experimentation, blasting guidelines were meticulously developed, aiming to enhance grindability and equipment productivity. The implementation of these guidelines promises significant improvements in operational efficiency and resource utilization, positioning Mont-Wright mine at the forefront of sustainable iron-ore extraction.

Jan 21, 2025

By David Scutt, David Noon

Blast crews are exposed to a number of major hazards including explosives and chemicals, ground conditions, machinery, unique work environments and specific blasting hazards such as fly rock and misfires. Unfortunately, injuries caused by sudden and/or unexpected movement of ground are continuing to occur. Blast crews are not equipped with the knowledge or tools to understand whether a high wall that they are planning to work under is safe.

Jan 1, 2011

By Ye Yuan, Jaak Daemen, Shaguo Yuan

ABSTRACT: A 400m2 (480 yd2) heavily reinforced high-strength concrete slab 800mm (31 inch) thick had to be demolished. Underneath it was a 300mm (12 inch) thick underlying structure consisting of three layers: a cushion coat, a water barrier and a concrete layer that protected the water barrier. It was strongly desired by the owner that the underlying structure, especially the water barrier, remain undamaged during the blasting demolition of the reinforced concrete slab above it. This paper discusses the design of the demolition blast, problems encountered, and practical solutions to these problems. First, the impact caused by the charge explosion on the remaining structure was studied. In order to limit crack propagation in the concrete to the bottom of the concrete layer, the concrete isolation layer underneath the bottom of the slab to be demolished was left in place, to protect the water barrier and its protection layer. The effects of blasting vibrations on adjacent concrete were analyzed and precautions were proposed in the design. A safe blast design meeting the requirements to protect the water barrier below the slab was detailed. Rainwater collected and stored above the remaining underlying structure remained in place for two weeks, confirming that the design and blasting were successful.

Jan 1, 2010

By Adrian J. Moore, Alan B. Richards

Responsible blasting requires that rock throw be controlled to ensure that no danger will result to people and property. This paper describes the development and testing of empirical field calibrated formulae that can be used to evaluate rock throw, provide an early warning of when reduced burden will endanger people and property, and prevent flyrock incidents. Inputs to the formulae are charge mass, burden or stemming height, and a site constant that lies within a general range that can be tightened by site calibration. The output is the distance that rock will be thrown, and this ‘design your own flyrock’ quantification can be used to establish both safe clearance distances, and the critical range of burdens and stemming heights where the situation changes rapidly from safe to hazardous. Examples are given of the use of the model to control flyrock in open-pit mining and quarry operations, in situations which are controlled by both burden and stemming height.

Jan 1, 2004

By Enver Alan

In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. S

Feb 1, 2020

By Paul Worsey, Terry Nixon

The development and testing of a simple mechanical stemming aid (Patents pending) resulting from a Joint venture by Incubator Technologies Inc. and the University of Missouri-Rolla and funded by the U.S. Department of Energy is described. The aid comprises a solid unit placed in the stemming above the explosive column and is designed to improve blasting efficiency and reduce drilling and blasting costs. It works with back filled drill cuttings or any other suitable stemming material.

Jan 1, 1988

By James Rowland, Richard Mainiero

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true.

Jan 1, 2008

By Jon Andrews

Purpose: To show how in managing risk in avalanche control blasting has changed throughout the years, and try to define the term “Acceptable Risk”. History: The history and the way we manage risk in avalanche control blasting to the avalanche control crews and public has change over the years dramatically. From the mid 1800s to about 1920 was the Risk vs. Rewards era, the Industrial Revolution. Now it is a Risk vs. Liability, the age of Liability.

Jan 1, 2009

By C A. "Hawk" Hanger

"The paper that will be presented is an in-depth study of sequential blasting using standardnon-electric shock tube down hole timing along with surface M.S. connector timing.Included also will be a discussion on the advantages in fragmentation, digability, oredilution' and ground vibration versus the common practice of row by row blasting. Alongwith the written presentation, several visual illustrations will be included. The visuals willrefine the actual direction and predicted movement of the shot involved."

Jan 1, 1993

By Josh Calnan, Paul M. Holmgren, Abigail N. Styer

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed.

Feb 1, 2020

By Ann Barron

Even though you think your company’s safety program is the best it can be, equipment, processes, supplies, surroundings and people do not always behave or react as expected. Consequently, needless accidents occur each year at quarries, construction sites, surface mines, and other locations where explosives are used. While blasting accidents account for only a small portion of the total accidents reported, the severity rate for blasting accidents is higher than for any other accident category.

Jan 1, 2007

By Bjorn Engsbraten

Explosive charges have been fired under defined conditions in a closed tunnel. The explosives have either been detonated in a steel tube or a single borehole. In the latter case dimensions, -loading density and confinement have been chosen to correspond to common practice.

Jan 1, 1980

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025