Search Documents

By Ali Kahriman, D. Adiguzel, R. Ulger, U. Akkaya

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. This paper presents the results of ground vibration analysis induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel. Different rock formations in this tunnel route which is 21.6 km in length were encountered during the excavation process by blasting. As a first stage, Hoek’s Geological Strength Index (GSI) values of rock units were determined by using inverse distance weighting method. The GSI values which were obtained from boring data were used when evaluate the data. GSI values were estimated by inverse distance method (figure 3) along with the tunnel route. Afterwards, ground vibration parameters induced by 21 shots which were made in different locations was monitored and passing routes of vibration waves determined. Weighted averages of GSI values were calculated according to distance of the regions where vibration waves passed. Multi regression analyze were made with using frequency, charge per delay, GSI and the distance between the shot point and monitor station. The main goal of this study is to investigate the relationship between ground vibration frequency induced by blasting and GSI.

Jan 1, 2011

By Guillermo Silva

A novel, ultra-low density explosive composition, particularly suited for wall control and other applications requiring customising of the explosive’s energy output, has been developed. Being reactive in nature, the low density explosive enables the controlled dilution of dry blasting agents from their nominal densities down to values slightly less than 0.10 g/cm3. The product has been detonated at densities of 0.07 g/cm3 in diameters as small as 50mm under confined conditions, using a 227 g (l/2 lb.) primer. Recorded velocities of detonation ranged between 1200 m/set and 2200 m/set for densities between 0.07 and 0.2 g/cm3. Theoretical velocities ranged from 1700 m/s to 2500 m/s for the same density range. The low density explosive was insensitive to initiation by a blasting cap which is a desirable feature for transportation purposes. Mixing of the product with ANFO has been accomplished with minimum segregation making it suitable for applications where reduction of pressures are necessary.

Jan 1, 2000

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By Ricardo González Dumuihual, Carlos Scherpenisse

A monitoring campaign to record dynamic pressures generated by detonation of a single blasthole was implemented at Barrick Gold´s Pueblo Viejo Open Pit mine (PVDC), located in the Dominican Republic . Pressure amplitudes beyond the dynamic compressive strength of the electronic detonator´s capsules have the potential to damage these electronic devices, generating misfires along with all the associated risks and entailed safety implications. In most instances, misfires generated from high dynamic pressures are a direct consequence of drilling deviations resulting in blasthole distances smaller than originally designed.

Feb 1, 2020

By Agus Setiabudi

East Pit Wira II Project in South Kalimantan, Indonesia with a radius of <500 meters (1,640 ft) from residential has about 454,168 tonnes of coal reserves, with a total remaining reserves of 3,369,383 tonnes (topography per end of June 2011). Thus, reserves may be lost as much as 13.48%. Therefore, it is needed to determine safe blasting technique which meets the Indonesian National Standards (SNI) No. 7571:2012 of vibration threshold, the maximum vibration of 3 mm/s (0.118 in/s) and air blast of 120 dB.

Jan 1, 2014

By Jorge Cárdenas, Piero Mejía, Diego Gamarra

The present case study details the solution to a complex situation in a mining operation, involving the challenge of expanding the tailings storage facility in high-criticality areas adjacent to electrical rooms that provide continuous power to the entire mining process, including water pumping and drainage systems. For this purpose, blasting is required to prepare the construction areas for the new expansion facilities. Upon deciding to proceed with blasting, a comprehensive engineering assessment was conducted to ensure operational continuity without impacting the process, while generating sufficient fracturing in the rock mass to allow extraction with auxiliary equipment. Support from specialists through the Technical Assistance area was requested, and a detailed evaluation was carried out through advanced studies. Field vibration studies were conducted to define attenuation models and characterize the rock mass in the sector. With this information, simulations were carried out using predictive and probabilistic models with Monte Carlo methods to select delay charges and optimal timing for reducing vibration levels and increasing frequency levels. With these measures, the three blasts conducted near the Gas Insulated Substation room, which had distances ranging from 30 to 100 meters, produced the following results: • Vibrations; The three blasts conducted at distances of 100, 30, and 50 meters recorded vibration values of 5.3, 40.2, and 9.5 mm/s, all of which were below the maximum vibration level of 50 mm/s set by the projects area. According to the USBM RI8507-OSMRE standard, all values for Peak Particle Velocity (PPV) and frequency were below the permissible limits. • Flyrock; Through filming and post-blast inspection, it was confirmed that the ejections were within the safety zone. • Fragmentation; The results obtained showed a maximum overbreak size of 1.5 meters, allowing the broken material to be moved effectively.

Jan 21, 2025

By Wilfrid Comeau

Vibrograms, which last significantly longer than the actual blast (say 10 to 15 cycles or more), may be signalling an elastic response, which is not uniquely blast related. For example, geophones mounted on a part of a structure, which can elastically resonate at a frequency included in the seismogram, may not show the structure’s real reaction to the blast. This resonance usually amplifies the ground vibration. This contribution examines one particular case where blasting excited and amplified a resonant ground response, and the method used to significantly reduce or eliminate this undesirable condition.

Jan 1, 2007

By Paul McAnuff, Alastair Grogan

In Canada, the only vibration regulations which apply across the entire country are intended to protect fish spawning areas. The Provinces and Territories regulate mines and quarries, and are responsible for setting vibration and airblast regulations. Some Provinces have set specific regulations, while others leave these restrictions to the mines inspectors who can set limits on a case by case basis. For the most part, it is left to individual municipalities to regulate blast vibrations and airblast from other blasting activities, which differ from jurisdiction to jurisdiction, and in some cases are not enforced. Blasters working in different jurisdictions have to be aware of the applicable regulations for the area they are working.

Jan 1, 2005

By Lindsay Wade, Peter Dare-Bryan

Benches in surface mines often contain known areas of ore and known areas of waste, which must be mined selectively. When rock is blasted it not only fragments but is also physically, and non-uniformly, moved. Risks therefore exist of ore being lost if treated as waste and of mill feed being diluted by waste. Both possibilities carry serious fmancial implications.

Jan 1, 2001

By Kirk Yeager

During the last several years the FBI has been involved with a detailed study of explosives designed to replicate formulations utilized world-wide by terrorists. In addition, numerous formulations , based on literature and internet sources were examined. During the early stages of this work, a good many of the energetic mixtures studied were based on simple ammonium nitrate fertilizer. While the use of ammonium nitrate in commercial explosives is well studied and documented, the characteristics of the mixtures produced by criminals and terrorists have been less well researched. To aid law-enforcement in understanding the properties of these poorly understood formulations, a “cradle to grave” examination of their characteristics was conducted.

Jan 1, 2001

By Stephen Chung, John Carpenter, Scott Gosch, James Breedlove

While controlling fly rock and ground vibration in quarrying in the neighborhood of a residential area, producing good fragmentation and keeping different grades of material separated in a muckpile are important in maintaining the productivity of quality aggregates. This paper describes a single row production blast for the study of fragmentation and displacement in the grade control carried out at a quarry of Barrett Paving Materials Inc. in Sylvania, Ohio. Digital video imaging was used to monitor the blast-induced motion of the bench face as input to the DMC_Blast (Distinct Motion Code), for the analysis of the formation of the muckpile. The actual digitized blast video and the DMC_Blast simulation are compared. The displacement and mixing of all the inter-bedded limestone layers are made visible in the simulated cross-section of the muckpile. The apparent fragmentation analysed with PowerSieve is also discussed.

Jan 1, 2001

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Ronald Joseph

Windows-based automated blast loading systems have long being conceptualised and never really taken off in the surface mining sector. However, with the introduction a windows-based automated blast loading and reporting system onto the Mobile Manufacturing Units (MMU’s) at Debswana Diamond Company operations in Botswana in August 2004, a project to automate blast loading (charging) and reporting ensued. This work was pioneered over three phases at Debswana’s Jwaneng Diamond Mine by African Explosives (Botswana) (Pty) Limited as part of the African Explosives Limited’s (AEL) integrated-mining (i-mining) concept. The first phase of the project involved the blast reporting system, at which time an average amount of explosives were loaded into all blastholes and all blast loading information was saved to a Microsoft Access 2000 database on the MMU computer. The second phase of the project, which ran until the end of the second quarter of 2008, involved manual blast plan loading and reporting system using flash disks, and the third phase which was installed and commissioned in the third quarter of 2008 and is currently operational at Debswana’s Jwaneng Mine, involves the automated blast loading and reporting system via Wireless Local Area Network (WLAN). This system is now routinely used to achieve operational and mining efficiency goals at the mine with respect to blasthole charging and blasting, and this paper briefly summarizes the status of this project at Jwaneng Diamond Mine where this technology is currently being monitored and also illustrates the positive mining impact that this innovation brings to the mining operation, both from an economic and efficiency perspective.

Jan 1, 2009

By Harry Verakis, Thomas Lobb

This paper summarizes the course of mine blasting safety, particularly in underground coal mining, in the USA for over a century of mining operations. During the late 1800's and especially in the first decade of the 1900's, a large number of mine explosions occurred in which blasting played a significant role. A contributor to the large number of mine explosions during this time period was the use of black blasting powder to extract coal and other minerals. A review is made of some of the more significant underground coal mine explosions that resulted from blasting operations during this time period up to the present day. The safety measures that were adopted and required by a series of laws as a result of mine explosion disasters in which blasting was one of the factors are examined. The time line of historical improvements in blasting safety and the tremendous reduction in fatalities and injuries over a century is illustrated and discussed. The improvements, which included the elimination of black powder and dynamite and the introduction of safer explosives termed "permissibles" occurred slowly over time and culminated from the occurrence of many coal mine explosion disasters. The blasting accident history over the past decade is discussed to show the great gains made when compared to the first decade of the 1900's. The most recent blasting accident fatality that occurred in October 2006 at a U.S. underground coal mine is also discussed. Although the blasting accident record is significantly improved from over a century ago, continual improvement is needed to reach the goal of zero fatalities.

Jan 1, 2009

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By Raden Haris Handayana, Jerri Mapanta, Eri Barlian, Milia Putri, Nasfryzal Carlo, Jihan Lubis

Waste oil is a growing problem throughout industries where environmentally responsible disposal ways are usually costly. There are many industries have developed process to reuse of waste oil as a source of energy on their own premises. Hanwha Mining Services Indonesia is one of blasting service that manufacturing explosive using waste oil. The usage of 60 % waste oil content in fuel solution already developed applied since 2020 at Petrosea-Kideco Site and will be increase until 100 % in 2022. The purpose of this research is to analyze the increasing of waste oil usage from 60 % to 100 % content at Petrosea Pit without reducing the emulsion quality and performance, and surely eliminate the fuel cost and reducing waste oil processing cost. Some trial conducted to determine the effect and quality of using 100 % waste oil content on emulsion at production blast. The method use to know the quality of 100% waste oil of emulsion is by direct application on bench blast. Using Microtrap VoD recorder, explosive energy will be recorded into m/s dimension, microtrap recorder the speed of explosive detonation in line with the speed of burning wire in the blast holes. The summarized of this research present that the using of 100 % waste oil content on emulsion can be applied on bench operation with the result of Velocity of Detonation (VoD) data is 4,559 mm/s, the mean of fragmentation size is in range 65.31 to 225.62 mm, the average of digging time on 1st layer is in range 10.2 to 11.6 s and on 2nd layer is in range 8.9 to 9.5 s, and the productivity still achieve on target. The result of all parameter quality still in the standard range of Hanwha and Petrosea.

Feb 6, 2023

By Catherine T. Aimone-Martin, Elena Oana Jacobs, Brent Meins

Accurate pressure measurements during underwater detonations are critical for the protection of structures and mitigating impacts to fish and marine mammals. Current guidelines that limit underwater pressures are based on past studies, many of which used sample rates of 48 and 65 kS/s (48,000 and 65,000 samples per second). These sample rates may be insufficient to accurately record high frequency, sharp rise time blast pressures. As such, pressure thresholds associated with fish and marine mammal injury or mortality may be underestimated, calling into question the pressure and sound pressure level guidelines that govern underwater blasting today.

Jan 1, 2019

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024