Search Documents

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By S D. Cummings

"CRACKS CONCERN CORPORATION" Was the headline on the front page of the Terre Haute Tribune Star, March 1994. Having spent several years following up on blast-induced damage allegations made this article especially interesting. Knowing that there were no operating mines within 30 miles of this newly built, yet to be occupied building, also made the reading more enjoyable. The article went on to read, "Vigo County school officials have asked architects to find out whether some cracks in walls at the new school are due to NORMAL settling or if they indicate serious structural problems." It is obvious that if there were a mine within "Feeling" distance, blasting and the operator would have immediately become suspect as at least one of the potential causes. More alarming is that the investigation may have stopped there.

Jan 1, 1995

By Robert B. Hopler

The Hercudet ? Nonelectric Delay Blasting Cap System has undergone significant changes since the last paper on the subject was presented at the 1978 S.E.E. Conference. The changes have been made to improve reliability of the blasting machine at low temperatures, and to improve efficiency and economy in usage in surface mining. The paper includes examples of the blast design process, details of use of the new in-hole connected cap, and delay patterns which have found use in quarrying and coal stripping.

Jan 1, 1980

By Jim Peterson, Ricardo Freire, Mason Biernat

Variable nature of rock and face conditions, varying execution and changing nature of blasting are making ongoing optimization challenging. Intelligent planning and on-going analytics are required to mitigate variability and convert blasting into a predictable outcome by use of technology. Blasting operations generate a huge amount of data which can be used intelligently for optimization. In this paper, details are provided of a system which is used for blasting data collection in the field – Key details around blast parameters, explosives, initiating system details, video, photographs, vibration and fragmentation are collected in a cloud-based platform. Data can also be collected through a mobility device in the field (even without internet connectivity) and synchronized with cloud-based system. Also, data from various sources can be imported in excel formats in the software including from upstream and downstream processes from blasting. App also gives indication about exceeding of vibration, air blast overpressure, fragment size etc. Thus, making it possible to perform QA-QC before charging and deciding initiation timing and sequence at the blasting site. The data can be processed and analyzed to spot trends, help predict events, and formulate strategies at the design and execution stage. Data gathering of blast parameters, explosive used processing and analysis can be used to optimize operational efficiency, improve safety and environmental controls.

Jan 1, 2019

Investigating blast vibrations typically utilises scaling and attenuation models for prediction of vibration amplitude over a range of charge weights and distances. A number of generalised relationships have been established from many years of far-field data analysis, where small changes in charge weight and ray-path distance are less critical. Under far-field conditions, small variations in local geology or geometry do not significantly affect the vibration scaling behaviour over an expected range of data. In the near to intermediate-field (less than 5 times the explosive charge length), small variations in wavepath and rock mass conditions between a blast and a monitoring point can greatly affect the outcome of vibration modelling. This case is especially true for underground blasting in sublevel open stoping, where the paths of blast-induced vibrations regularly encounter voids and preconditioned ground.

Jan 1, 2010

By Kamal Wadhwa

Liquid oxygen explosives have been used in India for well over 5 decades now. These are being extensively used both for shallow and deep hole blasting in the various opencast mines and quarries for mining of coal, limestone, ironore, bauxite, magnesite etc. IOL Ltd., are the pioneers in the introduction of these explosives in India and are marketing these under the brand name 'LOXITE'.

Jan 1, 1991

By S. Behera, K. Dey

This paper presents a methodology for finite element (FE) modelling to analyse the total deformation of rockmass under blast-load, with a focus on predicting backbreak that may occur during surface blasting operations. Backbreak can result from improper use of explosive energy, leading to damage beyond the excavation zone and jeopardizing operational safety and productivity. The paper highlights the impacts of backbreak on bench stability, excavator operation, drilling operation, flyrock generation, and improper fragmentation and boulder formation in surface blasting. However, prior estimation of extent of rock breakage zone can provide an idea to formulate the blast design to control the backbreak. While vibration-based prediction models are commonly used to estimate backbreak, they require physical blasting experimentation. To overcome this limitation, the paper describes the development of a FE model using ANSYS Explicit dynamics, which simulates rock blasting and calculates the total deformation of the rockmass. The rockmass deformation is modelled using Drucker-Prager (D-P) strength model with the Jones-Wilkins-Lee (JWL) equation of state for the explosives. The accuracy of the FE model is evaluated through physical experiments, and the results are compared with the vibration models. The FE model demonstrates close proximity to physical observations as well as vibration model result in predicting backbreak, thereby offering a promising alternative to vibration-based prediction models. The primary objective of the study is to predict the response of the insitu rockmass to explosive blast loading and determine the effective rock breakage zone.

Jan 1, 2024

By B Mohanty

Several parameters such as, Energy, Strength, Brisance, Impulse, and Bubble Energy, are in common use in the explosives industry today to rate commercial explosives in terms of blasting performance. However, this multiplicity of terms, their frequent interchange and their purported one-to-one correlation with expected performance have given rise to a considerable amount of confusion, and have often resulted in unrealistic rating of explosives. In this paper, various theoretical and experimental methods of estimating energy and performance of explosives are discussed and their relative merits examined. These methods include, Computer Code Calculations, Cylinder Test, Trauzl Test, Ballistic Mortar Test, Underwater Test and Model-scale blasting. It is shown, in the light of actual blasting process, that such measures cannot be considered accurate indicators of expected blasting performance as the properties of rock to be blasted are either totally ignored or only partially accounted for in these methods. It is also shown that no single technique alone among those currently employed by the explosives industry can lead to realistic rating of explosives in terms of expected blast results. The need for the adoption of a two-tier rating system, one based on chemical potential "energy", and the other based on blasting "performance" is proposed, and specific approaches to achieve this objective are outlined.

Jan 1, 1981

By Jason Wilkinson

Drilling operations are a vital component of surface mining, directly influencing productivity, safety, and cost efficiency. This paper explores a multi-faceted approach to drill optimization, focusing on minimizing delays, and enhancing operational effectiveness. Key areas of inefficiency such as shift changes, fuel and water delays, and time lost between drilling holes are analyzed to identify actionable improvements. Equipment related factors, including the frequency of drill bit and drill steel changes, as well as the condition of deck bushings, are evaluated for their impact on downtime and performance consistency. Additionally, the integration of smooth drives and shock subs is examined for their role in reducing vibration related wear and improving drilling precision. Optimization of pattern approach strategies is highlighted as a means to reduce non-productive movement and align drilling with blast design more effectively. To support continuous improvement and accountability, the implementation of a driller scorecard is proposed. This tool enables the measurement of individual performance based on key operational metrics, fostering a culture of data driven management. Through a combination of field data analysis and best practice recommendations, this study provides a comprehensive framework for enhancing drilling productivity in mining operations. The findings aim to support mine operators in achieving higher efficiency, reducing operational costs, and extending equipment life through targeted optimization strategies.

Jan 26, 2026

By William. J. Birch, Catherine. E. Johnson, Robert Farnfield

Rocks and other materials can be characterized by their elastic properties. However, seismic velocities represent a more practical set of physical properties for seismic methods. Seismic velocities define the speed at which various elastic deformations propagate through different rock types. Seismic velocities for a given material can be expressed explicitly in terms of their elastic properties. It is widely accepted that the peak particle velocity and associated frequency of ground motion are important parameters for determining a safety criterion to minimise the potential for both damage to structures as well as nuisance to people. Whilst the key considerations are the blast design parameters, the seismic velocity is important as particle velocity is dependent in part on the powder factor [blasting ratio] which in turn is found to be dependent on the seismic velocity.

Feb 6, 2023

By Rajesh Sonkar, Sanjeev Kumar

The deployment of Dragline machines in opencast coal projects involves huge capital expenditure as well as operating costs. The mine operators always endeavor to ensure smooth excavation of material by the Dragline machines while meeting the major objectives of safety, minimal disturbance to environment and optimal operating costs. Optimization of fragmentation through well designed blasts is fundamental in meeting part of the objectives is good fragmentation of rock or mineral proposed to be lifted by the Dragline machine. If the overburden lying over mineral is not properly fragmented, it may result in formation of ‘Toe’ the removal of which is the most arduous task in opencast coal mines. The mine operators always endeavor to achieve best possible results in blasting to ensure smooth operation of the high cost Dragline Machine. However, despite continuous efforts by the blasting engineers involved in bench blasting for the machine, the formation of ‘Toe’ is an ever nagging problem faced in large opencast coal projects eventually reducing the overall operational efficiency of mining.

Jan 1, 2011

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By Christopher Laughton

A new underground laboratory is under construction at the recently closed Homestake Gold Mine, Lead South Dakota, United States of America. The Deep Underground Science and Engineering Laboratory is designed to meet the needs of an international group of scientists and engineers interested in conducting fundamental and applied research at depth in the Earth’s crust.

Jan 1, 2011

By Randall M. Wheeler

Pre-blast surveys are used to document the condition of a structure prior to the commencement of blasting activities. They provide the best means of determining the pre-existence of visible cracking and deterioration in a structure before blasting is initiated. A small investment in a good pre-blast survey, coupled with good public relations, could mean a large cost savings for a company in the future.

Jan 1, 1992

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By Craig Adams, William Poe

Introduction The United States Department of the Interior, Minerals Management Service (MMS) is mandated under the Outer Continental Shelf Lands Act (OCSL A) and the Energy Policy Act of 2005 to oversee leasing, exploration, development, and production of mineral and renewable energy resources on the Outer Continental Shelf (OCS). Under these authorities, MMS is responsible for permitting and overseeing an array of offshore operations; some of which involve the underwater detonation of explosive charges. Explosives are most critical for their use in the severance of bottom-founded piles and well components during the decommissioning of OCS platforms and well abandonment work.

Jan 1, 2011

By Hideaki Kitajima, Daisuke Fukuda, Kazuma Moriya, Katsuya Sasaki, Katsuhiko Kaneko

The purpose of this research is to analyze the fracture process and achieve design optimization of a splitting method for concrete and rocks termed the electric discharge impulse crushing method (EDICM). The EDICM utilizes the cartridges being set in boreholes in the splitting target. The cartridge has a thin metal wire and is filled with nitromethane. By applying the electric discharge to the wire in the cartridge, plasma is caused leading to the vaporization of the wire. Then the deflagration of the nitromethane commences, which generates borehole pressure for splitting the target. Although the required splitting time is roughly several hundred micro-seconds and much slower than ordinary blasting, the fracturing still completes in quite short time and understanding the fracture process of opaque and brittle materials such as rock and concrete in this time scale is of academic importance.

Jan 1, 2011

By V Krishna Mohan, J Edmund Hay

This paper discusses the results of the gap sensitivity measurements made on water-gel explosives, sensitized by monomethylamine nitrate (MMAN) and flake aluminium, and one emulsion explosive. This study specifically deals with the effect of the mode of initiation, end or center, on the measured L50 values with air gap and coal dust gap for the above explosives. Similar measurements have also been carried out on a nitroglycerine (NG) - based explosive. The results show that the mode of initiation plays an important role in determining the air-gap sensitivity of these explosives. However, in tests carried out with the coal dust gap, the L50 ( grams of coal dust ) values for these explosives are close in both the types of initiation. The results indicate that the sensitivities of these explosives may be ordered in the following manner: NG-explosive>> Aluminized explosive ~ MMAN-explosive > Emulsion explosive

Jan 1, 1982

By Rob Farnfield, Mark Pegden

Old Cliffe Hill quarry produces between 4 and 5 million tonnes of crushed granite per year and is located in the county of Leicestershire in the East Midlands region of England. Blasting is carried out with bulk emulsion explosives in combination with either shock-tube or electronic detonators.

Jan 1, 2010

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991