Search Documents

By S. Lim, G. Walsh, V. Romero

The cable television show, Mythbusters, contacted the New Mexico Institute of Mining and Technology requesting a pressure gauge to be used in underwater testing. The requirements for the gauge were: it must be passive (i.e. require no power to function), it must indicate when a certain, pre-determined pressure was reached, and that indication was to be visual. A pressure gauge was developed, using standard, commercially available rupture discs, set to burst at 500 psi. Underwater testing was conducted using a 400 lb Pentolite charge. Test devices were set out at ranges from 50 to 200 feet from the seat of the blast. The rupture discs showed a lethal range up to 100 feet, but not at 150 feet. This result matched well with the behavior predicted through modeling and simple shock physics calculations. Additionally, the geometry between the incoming shock and the pressure gauge did not seem to have a strong effect on gauge performance.

Jan 1, 2009

By Jason Baird, Philip Mulligan, Caleb Baumgart

This report details the pressure variances, measured at four pressure sensors placed equidistant from the center of an airburst explosion, as the blast pressure from a single charge expands radially. Many of the empirically derived equations used for predicting the blast pressures of an explosion, assume a point source detonation and that the radial pressure expansion is equal. The authors understand that the equations used to approximate the blast pressure may not have 100 percent agreement with the observed pressure. However, during previous research at Missouri University of Science and Technology (Missouri S&T) the pressure variances had a range of 1,200 psi, between the four pressure sensors placed two feet from the center of a 1/2-pound (226.8 gram) of hand packed C4. The variances indicated that at the close distance from a suspended explosive charge the pressure does not behave as that observed from a point source.

Jan 1, 2014

By Alastair Torrance, Italo Onederra, Do Sun Kim, Kush Patel, Gary Cavanough

Reactivity of ammonium nitrate-based explosives is associated with the presence of sulphide in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. This paper explains the mechanism of these reactions, the potential cause of spontaneous detonation and how inhibited explosives prevent the reaction

Jan 1, 2019

By Chick Kerkering, Stephen Iverson

Perimeter control blasting is common in civil construction projects but not as common in mining. A poorly designed and executed underground mine development blast design can result in unwanted wall rock damage. This damage increases the risk of rock falls and injury. With the availability of good drilling equipment, it is a simple matter to add the few extra holes needed to change conventional drifting into drifting with perimeter control.

Jan 1, 2008

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By Catherine T. Aimone-Martin, Kristen Kolden

In August of 2013 the USDA Forest Service (USFS) blasted bedrock at the base of a waterfall in Kanalku Creek within the Kootznoowoo Wilderness Area on Admiralty Island in the Tongass National Forest located in Southeast Alaska. The purpose of the blasting was to widen and deepen a plunge pool at the base of a waterfall complex considered to be a partial barrier to migrating sockeye salmon. Drilling and blasting to remove 12 to 15 cubic yards of rock occurred over a two day period.

Jan 1, 2015

By Per-Anders Persson

TIGERWIN, now on CD, is a user-friendly personal computer code (running under Windows) which determines the detonation and expansion state of an explosive from its known chemical composition. TIGERWIN is intended for users in the mining and commercial explosives industry who do not routinely program or run Fortran codes. The code allows the user to open a window on the computer screen and enter the initial density and the weight percentage composition of an explosive, ingredient by ingredient. Alternatively, the code can balance the composition with one or more ingredient percentages fixed, while proportionally adjusting the others automatically to give a total of 100%. The equation of state and its parameters can be user-selected from several proven and tested versions of the BKW, the JCZ, and the ideal gas equations of state. TIGERWIN allows the user to select several options for different additional calculations, such as determining the constant volume explosion, the Chapman-Jouguet (C-J) point, the detonation Hugoniot, the expansion isentrope from the C-J point, and point calculations with selectable specific volume and temperature. Additional options include calculations of detonation data with one or more ingredients partially reacted, assuming either temperature equilibrium between reaction products and unreacted material, or keeping the unreacted material “cold” at the initial temperature. Thus the code can run both ideal and non-ideal detonation calculations. The code automatically saves the input and output files in a separate directory for future reference. The output from several calculations can be displayed and printed in the form of a comparison table. In it, the key results of up to five calculations with different explosive compositions can be compared. The results from an individual calculation can be displayed graphically and printed with expansion work, pressure, or temperature as functions of specific volume. A complete listing of the details of the calculation results, similar to those from the original Fortran Tiger calculations, can also be displayed and printed. No computer experience is required to run the code and workshop participants are encouraged to bring in their own formulations to try out on TIGERWIN

Jan 1, 2000

By Marco Larghi, Jurg Knobel, Braden Schmidt

Remote Avalanche Control Systems (RACS) which uses solid explosives has been used in Europe since 1996 and North America since 1999. With large destructive avalanches in transportation corridors, various States and Provinces have started implementing RACS into their summer construction projects to minimize traffic shutdowns. Since 2014 in North America, many of the projects are requiring the RACS deployment boxes to be removable by light duty helicopter for loading and summer storage. This is to further remove workers from the mountain tops, where inclement weather and Occupational Health and Safety concerns are widespread. We did not believe the method of flying primed charges under a helicopter was safe, so we developed a new charge container to deal with the issue. In spring of 2016, the Inauen Schatti company of Switzerland started the development of a flyable RACS deployment box to complement their 2 stand alone tower systems. To go along with the new flyable deployment box, a new S-Load charge carrier was developed. The newly developed and patented S-Load explosive charge for the LM32 RACS system features a mechanism which combines the explosive and priming material just before the blast. These are stored separately during transport and storage in the LM32 RACS deployment box. The S-load is divided into two parts. The upper part contains the plastic bobbin and ignition sequence (impact pull wire igniter, safety fuse and #8 blasting cap), whereby the explosive material and detonating cord are positioned in the lower part of the explosive container. The explosive material and ignition sequence are separated by a certified housing during transport and storage. The key idea of the S-Load system was to achieve a maximum level of safety by keeping the priming components separate from the explosive material until just before detonation. Because of this the S-Load and the LM32 tower remains safe during transport by helicopter or when being stored in the deployment box on the mountain side in the avalanche start zone.

By P D. Katsabanis, K Steeves, D Dombrowski

Accurate electronic detonators with firing time accuracy within 100 microseconds of the nominal have been used to control blast results in terms of fragmentation, vibrations and wall control. Axisymmetric experiments and experiments utilizing small benches have been conducted in order to calibrate a numerical model under development and examine the influence of delay interval on wall control, fragmentation and vibrations. The results obtained so far indicate definite advantages of precise timing in reducing back break and wall damage. Fragmentation is affected by the delay interval and high speed film observations and measurements indicate that the delay interval should allow the damage zone from each blasthole to be fully established prior to the detonation of the next borehole. Studies on vibration control demonstrated that vibration synthesis work using signature shots can only be of use if accurate delays are employed.

Jan 1, 1995

By Robert Jacob Cefalo, Rio Tinto Kennecott

At the end of 2016, the Mine started a new ore phase in the section of the pit located on the East Wall. The East Wall geological structures required controlled blasting for peak particle velocity (PPV) frequency vibrations to protect the wall. Frequency controlled blasting using linear seed wave superposition modeling was required and implemented to reduce the far-field affects to the wall. This paper covers the work done by the drill and blast engineering group, controls used to protect the mine infrastructure, and the continuation of work-to-date of frequency controlled blasting for wall stability. The narrow width of the layback required the combination of hole sizes to blast large diameter production patterns with smaller diameter trim patterns in the same blast. A single blast had to use different burden & spacing and hole diameters and required the use of different timings throughout the pattern. Electronic detonators were required to limit blast vibrations and accommodate the specific timings needed to reduce low frequencies. The geotechnical group with the help of geotechnical radars worked with the drill and blast group on creating a tracking and reporting of blast performance. The radar readings informed the drill and blast engineers of the performance of the blast as it related to the long term performance of the highwall

Jan 1, 2019

By Marco Larghi, Jurg Knobel, Braden Schmidt

Remote Avalanche Control Systems (RACS) which uses solid explosives has been used in Europe since 1996 and North America since 1999. With large destructive avalanches in transportation corridors, various States and Provinces have started implementing RACS into their summer construction projects to minimize traffic shutdowns. Since 2014 in North America, many of the projects are requiring the RACS deployment boxes to be removable by light duty helicopter for loading and summer storage. This is to further remove workers from the mountain tops, where inclement weather and Occupational Health and Safety concerns are widespread. We did not believe the method of flying primed charges under a helicopter was safe, so we developed a new charge container to deal with the issue.

Feb 1, 2020

By Braden Lusk

This paper includes results from analysis of recorded Acoustic Responses of Structures to Blasting. The analysis was performed to determine specific characteristics of sounds experienced inside homes during blast events. Data was collected in a typical house within the Boone North No.2 Coal Surface Mine in Ashford, WV which was instrumented for several blast vibration and acoustic responses. The instrumentation consists of four acoustic microphones distributed throughout the internal areas of the house and three geophones buried near the house. Two additional channels collect the trigger signal and Air Blast information. For each blast event recorded by the system, the mine blast reports were used to obtain major blast characteristics such as distance from the blast to the instrumented house, weight of explosive used, number of boreholes, delays, and other important parameters. This information allowed study the relationship between the acoustic response and the blast design. From a database of 43 records, five records were chosen for complete analysis. These records were chosen based on distance from the blast to the house, and specific blast parameters. This paper presents the result of the relationship between the frequencies and amplitudes for the entire trace of acoustic records, the response due to ground vibration (GV), and the response due to air-blast (AB). Frequency content was obtained through Fast Fourier Transforms (FFT), using D-Plot software. The records have a typical shape that permits cutting and analyzing each part of the signal with respect to GV and AB separately. Some conclusions are reported concerning the relationship between blast parameters and acoustic response of structures.

Jan 1, 2009

By R Heater, G Glynn

Various small diameter commercial grades of slurry and emulsion explosives were tested and compared. Velocity diameter curves for confined and unconfined charges were established and the effects of temperature and hydrostatic pressure on critical diameters and minimum primer weights were determined.

Jan 1, 1984

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By Anne Caroline Costacurta Polli, Jose Rojas Cáceres, Roberto Mahler de Morais, Thais Costa Silva

The technology and the knowledge about the behavior of explosives and detonation accessories allowed to create new products for different situations by the restrictions imposed by the market. In a Brazilian underground copper mine the restriction occurred in the use of high grammage Det Cord in the development heading blasts perimeter holes. Enaex Brazil has developed Densiex UG™ (Low-Density Bulk Emulsion), a water-resistant bulk gassing emulsion with a density ranging from 0.60 to 0.90 g/cm³ to replace the high grammage Det Cord in blasts. That product is pumped in the same Mobile Manufacturing Unit (MMU) as Enaex Brazil's standard underground (UG) bulk emulsion. This product has a Lower Velocity of Detonation (VOD), vibration, and detonation pressure, which contributes to a better finishing of the drift, lower impact in the support structures, and lower generation on unstable rocks in the perimeter of the drift. This case aims to summarize the results of the work on the application of the Low-Density Bulk Emulsion in perimeter holes in an underground development gallery at an underground copper mine in Brazil. During this work, 10 horizontal drift blasts were performed using the Low-Density Bulk Emulsion, which presented an average density of 0.64 g/cm³, increasing safety, a 25% reduction in overbreak, a 23% reduction in scaling time, elimination of rework, and a saving of $135,000 per year for this business partner that immediately implemented this new product in all blasts at this mine.

Jan 21, 2025

By Per-Anders Persson

This chapter deals with the concepts of shock wave8 and detonation wavea together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of thii chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1998

By Thomas Rupp, Michael Siegwart

The paper presents the vibration and sound emission measurement campaigns carried out in 2007 in preparation for the Ceneri-Basistunnel construction. We also present the vibration measurement campaign conducted during the construction of the Zimmerberg-Basistunnel. Both tunnels form an integral part of the Swiss Federal Railway Company Neue Eisenbahn Alpentransversale project (NEAT). This strategic project comprised the construction of several new tunnels. Its aim is the improvement of the existing infrastructure. The improved infrastructure will be able to accommodate a larger volume of railway traffic that is also crossing the Alps at higher speeds. The construction of the Ceneri-Basistunnel commenced in 2006. Both the Zimmerberg-Basistunnel and the Ceneri- Basistunnel are located underneath densely populated areas. Therefore, noise and vibration emissions have to be kept to a minimum and must not exceed applicable codes of practice. In order to identify the most appropriate blasting strategy for the yet to be constructed Ceneri-Basistunnel, blasting trials were conducted. The paper presents the findings of these trials and identifies ways to reduce both noise and vibration emissions from blasting. The construction of the first phase of the Zimmerberg-Basistunnel took place between 1999 and 2003. While the first phase is already in operation, the construction of the second phase has been postponed (commencement originally due in 2007). The Zimmerberg-Basistunnel connects the outskirts of Zürich with the city centre. As the tunnel site was not located close to the surface near populated grounds, no special measures were needed to reduce the noise emissions from blasting. However during the construction of the tunnel, the vibration emissions from blasting were monitored on more than 50 locations on the surface. The paper presents the analysis of some of the data. An emphasis is placed on the appropriate synopsis and presentation of data for documentation purposes.

Jan 1, 2009

By J. Rafael Otaíza, Francisco Mardones

This work has addressed the problem of creating a predictive model of the maximum particle velocities in the rock mass (PPV). The model designed specifically can model the subsequent vibrations of blasting based on geometric parameters, explosive loading, and the blasting process itself. Models based on artificial intelligence (AI) algorithms can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. These models have been successfully used in similar contexts (Prashanth, (2018)) and have achieved state-of-the-art results in the field (Lawal, (2021)). The main challenge is to adapt them to the context of Chilean mines, in addition to including the geometric information of the blasting and the heuristic to obtain the set of optimal parameters, it is proposed to follow the work of (Simonyan, (2013)) and obtain "saliency maps" adapting it to tabular variables. We implemented an Artificial Neural Network (ANN) with a large number of neurons in the hidden layers. Models based on neural networks can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. The literature shows that, for the problem of rock type identification, basic neural networks perform well (Simonyan, (2013)), but lack uncertainty estimates. This is a data-driven model, and in this sense, the model training was carried out using data from multiple operations in the large copper mining industry in Chile. In these databases, data consistency and the balance of the various independent variables that have the greatest impact on the model were ensured. With the above, the optimal hyperparameters of the model were determined, obtaining a predictive R-squared of 0.94.

Jan 21, 2025

By Romel Villanueva, Juan Vasquez

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process. For gassed explosives the density varies gradually according to the depth in the hole, due to the pressure on the bubbles by its own weight. The density at the bottom of the hole can reach critical values, which directly affects the start of the detonation in the booster zone with a high probability of nitrous fumes formation. On the other hand, density translates into the amount of explosive and energy available. Therefore, for the optimum performance of the explosive, the minimum and maximum values of the in-hole density must be determined. For the cases studied, the maximum in-hole density and the maximum charge length have been determined. When the charge length is greater than 7.0 m [ 23 ft.] special care must be taken with the cup density, which as a general rule should not exceed the value of 1.15 g/cm3 [71.8 lb/ft3] at the risk of losing the sensitivity at the bottom, also increasing the probability of nitrous fumes, bad fragmentation and finding intact explosive after blasting. In the large holes in Toquepala and Antamina mines, where the charge length can be greater than 9.0 m [29.53 ft]. If the cup density is greater than 1.15 g/cm3 [71.8 lb/ft3] the in-hole density can easily reach a high value of 1.30 g/cm3 [81.16 lb/ft3].