Search Documents

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

By S. Gajardo, E. Valdés Guerra

Together with Sociedad Punta del Cobre S.A. (Pucobre) and Orica, we are carrying out a study of alternatives for methodology of excavation in Slot Up Raises from actually built with Blind Hole (BH) to drilling and blasting (DB) methodology. The study is part of the permanent search for innovation, the use of technology and the reduction of mine operation costs. This application aims to optimize the Sub Level Stoping method, which has historically been exploited at Pucobre. Using a new variant of the method “Open Stoping”, through the initial development of ascending blind raises using a pilot drilling of a bore hole, with the objective of eliminating the upper level in order to excavate the free face opening. This industrial test aims to replace the mechanized BH Up Raise of 1.5m (4.9 ft.) in diameter and 30m (98.4 ft.) high, with a Up Slot Raise considering two separate blasting events, using different technological enablers, as detailed below: accuracy drilling with relief holes of 254mm (10 in.) diameter, high viscosity bulk emulsion, wireless initiation system and high-strength injectable bulk resin. Considering the importance of the success of this application, a DB diagram was defined to allow the opening of the up raise in two blasting events, separated by intermediate stemming deck located at the same level at a height of 15m (49.2 ft.) from the collar, using high-strength injectable resin. The first blasting event considers the first section from the collar to the first 15m (49.2 ft.), using wired electronic initiation that is detonated on the first day. A second event blasts the section from 16.5 to 30m (54.1 to 98.4 ft.), using a wireless initiation system, as, it has no physical connection, is blasted on the second day after the extraction of the material resulting from the first event. For greater precision, the design of the explosive charge configuration and initiation sequence is made, adjusted to the measurements of trajectory deviations of the actual ground drilling and is also considered for the control of the explosive charge configuration with high viscosity bulk emulsion. This application improves the profitability of the mining business by generating savings through the change of Blind Hole methodology, estimating a savings of more than 75% per Up Slot Raise

Jan 1, 2024

By A T. Spathis

Corrections are given for “A three parameter rock fragmentation distribution” by A.T. Spathis (Measurement and Analysis of Blast Fragmentation, Workshop hosted by 10th International Symposium on Rock Fragmentation by Blasting, New Delhi, India, November 25-29, 2012 pp. 73-86). Typographical errors in two equations for the uniformity index in the two versions of the original and modified Kuz-Ram model are corrected. It is noted that the modified equation in the original published paper of Cunningham also had the same typographical error. A corrected plot of the dependence of the uniformity index versus the burden to diameter ratio is given. These corrections do not affect the rest of the original published paper.

Jan 1, 2013

By Richard Givens, Thomas Baginski

Technological advancements in warhead designs and implementations have driven the development of arrayed initiation networks of highly accurate, highly reliable, and extremely safe detonators. Recent development efforts have produced advanced Exploding Foil Initiator (EFI) based systems that have been adapted for civilian use in commercial blasting applications.1,2,3,4,5 This novel, high technology system promises multiple improvements and advantages over the manufacturing, transportation, tracking, storage, inventory and field operation of current detonator systems. Ultimately the insertion of this technology would result in fielding a Non-Energetics Based Detonator (NEBD). Insertion of complementary technologies into the detonator’s supporting systems would greatly advance current detonator hardware/software.

Jan 1, 2011

By Catherine Johnson, Barbara Rutter, Phillip Mulligan

Shock tubes, shock tunnels, and blast tubes have been widely used by explosive researchers and shock wave investigators to understand the characteristics of shock waves. Rectangular, cylindrical, and conical are the three simple geometries commonly used in shock tube and shock tunnel testing. These geometries result in shock waves that resemble the Friedlander curve’s simple exponential decay. However, geometries that are more complex have not been studied. This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile. Shock wave profiles were measured inside and outside the LATS to investigate the geometry’s effect. A representative shock wave profile from each geometry and open-air explosive testing were compared visually showing the geometries effect on the shock wave profile. The LATS produced a waveform with four pressure peaks behind the initial shock front, which were found to be associated with the four rectangular sections. The resulting pressure trace was compared to pressure traces from simulated urban bombings. The number of turns in an urban environment equated to a new peak, which is caused by additional expansion sections of the shock tunnel. From this observation, complex geometry shock tunnels can be purpose built to simulate an explosion in an urban setting. The use of shock tunnels with complex geometry in simulating urban bombings can allow for numerous representations and a better understanding of profiles produced during an urban bombing or similar scenario.

By Michael Wieland

Work-principle computations for explosions underwater or in rock reveal the way the thermodynamic characteristics of surrounding material influence the resulting shock and heave. To reach total thermodynamic equilibrium under such transitory dynamic circumstances, reactions must quickly readjust to changing circumstances, which works for molecular (military) explosives where the fuel and oxidizer type atoms are originally in close proximity. For non-molecular mixtures with their dispersed zones of oxidizer or fuel, in particle or droplet form, there are numerous unproductive collisions, increasing the wait time required to reach chemical equilibrium. Underwater test data for molecular explosives compare rather well with the shock and heave resolved from the work-principal model, while the non-molecular explosives normally used in mining tend to yield a noticeable discrepancy. Years ago, it was recognized that the underwater shock was lower than expected and the heave was higher than expected for ammonium nitrate fuel oil (ANFO), though their resultant sum for the total work was roughly what was expected. When the readjustment of thermodynamic equilibrium warrants quicker chemistry than occurs in underwater or rock shooting, the time-retarded chemistry reduces the shock and raises the heave within the surrounding material without reducing the total work, unless the reaction retardation is quite severe. This technical complication in reality is a nonequilibrium issue that is difficult to resolve with just thermodynamics, though a rational set of transformation factors is formulated herein to represent those circumstances.

Jan 1, 2008

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By B Mohanty

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2014

By Aaron Nickoli, Brad Clark, Thomas Horan E. I. T.

The Canal Road Dip Slide is an active landslide located on South Pender Island, British Columbia. The effects of the fall 2021 atmospheric river prompted the British Columbia Ministry of Transportation and Infrastructure to initiate an emergency response project to realign Canal Road out of the active landslide zone for safe traffic passage. The work was tendered in a bidding process and included blasting and rock excavation work at the project site. Tetra Tech Canada Inc. was retained by the contractor to be their Blast and Vibration Specialist. The close proximities of an active landslide, a Canadian National Park, and other segments of construction posed stringent constraints to blasting. The governing constraints to blast design included a Peak Particle Velocity (PPV) limit of 3 mm/s (0.12 in/s) along the adjacent landslide centerline and a slide movement constraint. Sixteen blasts were executed throughout the scope of work to remove 2595 m3 (3394 yd3) of meta-sedimentary rock. Blast designs adhered to the constraints by utilizing up to quadruple decking in 50+ blast holes which lead to complex timing schemes. Several blasts were over 4 seconds in duration, with one at nearly 8 seconds. The landslide area was monitored with Shape Accel Arrays (SAA) throughout the scope of work that tracked geohazard slide movement during construction. The SAA data is presented, and the effect of blasting is discussed. Site specific parameters for PPV estimation were calculated and are presented. Collaboration and communication between the stakeholders allowed the project team to successfully overcome the technical challenges posed by the Canal Road Dip Slide.

Jan 26, 2026

By John Norman

This paper will cover blasting techniques that are applicable to underground and other rescue that involves removing obstacles and breaking rock in close proximity to rescuers and subjects.

Feb 1, 2020

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Alan R. Gadberry

To resolve drilling and blasting problems, rather than treating symptoms and allowing problems to grow, the mine operator needs to change the way he operates. When a mine operator discovers a drilling and blasting result that he doesn't like, it is easy for him to think of that disappointing result as a problem. More often than not, however, that result is only a symptom of a problem, and the real, underlying problem cause can be seen when the operator looks in the mirror. Symptoms and problems relating to drilling and blasting are resolved when the mine operator makes appropriate changes in the way he manages his operations.

Jan 1, 1985

By Wm. Reisz

There is no universal standard for Standard Operating Procedures (SOP’s). Every blasting operation has its own unique circumstances, its own methodologies and its own unique demands. It would be nearly impossible to create a one-size-fits-all document that would be totally appropriate for every blasting scenario. But there are universal objectives that should be adopted in any set of blasting SOP’s.

Jan 1, 2010

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Jim Smith, Jeff Hudreth, John White

Jan 1, 2000

By Amos Bryant, Jesse Davis

This paper compares the predictions of the latest Institute of Makers of Explosives Safety Analysis for Risk (IMESAFR) model versus physical test data recovered from ISO-1 and ISO-2 tests in Woomera, SA. ISO-1 testing included placing 1054 kg (2324 lbs) of ANFO (ammonium nitrate-fuel oil) inside an ISO container on a flat bed truck. ISO-2 testing was identical except the NEW was 4000 kg (8818 lbs). The IMESAFR predictions are based on model runs using the best match available to the actual donor type involved in the test. This type of debris analysis is not the standard output of IMESAFR, as the program is designed to assess the probability of human fatality. However, all of the IMESAFR predictions presented were obtained from the use of the actual model equations and algorithms without adjustment. Test results from ISO-1 and ISO-2 will be presented as well as findings from the comparison between model results and actual explosive results from the ISO testing efforts.

Jan 1, 2010

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By Paul Worsey, Yasutaka Dote

The choreography of large fireworks displays dictates electric initiation for precise timing. It has been common practice to pre-squib products before transportation for reducing set up time. A number of fatal accidents transferring pre-squibbed product during transportation suggests that there is a problem with impact sensitivity. The aim of this paper is to quantify the impact sensitivity of the various configurations of initiating materials used in display fireworks.

Jan 1, 2009

By Tom Watts

This paper will focus on the design, manufacture and use of pump safety systems on MMUs (Mobile Manufacturing Units – Bulk Trucks) with progressive cavity pumps. The practice of pumping bulk blasting agents is highly regulated and the explosives manufactures have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping.

Jan 1, 2009