Search Documents

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

By R. L. F. Kay, T. A. Fletcher, A. J. Boyce, C. M. Rice

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The synorogenic, mafic Ordovician intrusion comprises orthopyroxene-rich xenoliths and mafic-ultramafic cumulates with low-grade pyrrhotite, chalcopyrite and pentlandite mineralisation. Despite abundant textural, mineralogical and O isotope evidence for significant assimilation of country rocks, S isotopes indicate only a modest uptake and suggest that mineralisation is dominated by magmatic sulphur. The preferred explanantion is that the magma was close to S saturation on emplacement. Uptake of elements such as Si and O led to early crystallisation of orthopyroxene, resorption of olivine and early segregation of a sulphide liquid. Post-magmatic interaction with a high-temperature, surface-derived fluid, whose movement may have been controlled by regional shear zones, reset biotite and whole-rock O isotope values but not those of orthopyroxene. This model identifies the presence of olivine-rich rocks and evidence of extensive assimilation as guides to prospectivity

Jun 19, 1905

By S. P. Mishra, G. R. Chaudhury

The adsorption of Cu2+ ions by Penicillium sp. displayed a dual rate, with an initial faster phase followed by a slower one. The adsorption rate increased with increasing pH due to chemical and biochemical reactions. The Cu-loading capacity of the biomass increased at higher initial Cu2+ concentrations. Above 40 degrees C the adsorption rate decreased which may be due to partial hydrolysis of biopolymers which are essential constituents of the cell wall. Adsorption kinetics followed the Freundlich isotherm and the equilibrium concentration that was calculated on the basis of the isotherm matched the observed value well. A series of theoretical adsorption curves were produced using mathematical correlations between the mass transfer coefficient, the Cu2+ ion concentration at equilibrium and at time t. The correlation between the theoretical and observed adsorption rates for different experimental conditions was good. It was concluded that the results from the study were best explained using a mass-transfer adsorption model

Aug 1, 1995

By A. D. Fowler, M. T. Anderson

A phenomenological model is presented that relates Pb-Zn mineralisation to proximal geopressure zones. Typically, geopressure zones (GPZ) consist of masses of undercompacted sediment encapsulated within impermeable shales and are characterised by high formation fluid pressures. Heat flow is perturbed in some GPZ on account of their insulating properties. Geothermal gradients as high as 150 degrees C/km have been observed over short distances in the sediments of the US coast of the Gulf of Mexico. Some modern geopressure zones are known to reach temperatures of 120-150 degrees C at depths of 2.5-3.5 km. It is demonstrated that the zones may act as proximal sources of hydrothermal fluids, thus explaining the high temperatures of mineralisation observed in the deposits, which are hosted in basins characterised by thick, rapidly deposited, shale-rich clastic sequences

Jan 1, 1991

By S. L. R. Lenharo, H. Kahn, H. Born

Different ore types result from the irregular spatial distribution of the associated alkaline/carbonatite rocks and the zoned alteration profile within which apatite may have undergone reprecipitation. Different flotation responses are caused by their mineralogy, iron oxide impregnation and grain-size characteristics. Samples from seven deposits were crushed, screened and separated before being studied by chemical analysis, optical microscopy, X-ray diffraction, FTIR spectroscopy, cathodoluminescence and scanning electron microscopy. Two main apatite varieties with peculiar crystal morphology were identified: hydroxy-fluorapatite as the primary phase and carbonate-fluorapatite as the reprecipitated phase. The former occurs as prismatic or ovoid grains and the latter as polycrystalline aggregates or crusts on the primary grains; both are associated with iron oxide coatings (primary) or intergrowths (secondary). Microflotation tests showed variations in flotability for particular apatite associations as well as intensity of iron oxide coatings. The differences in flotation behaviour can be related to morphological properties and chemical substitution in the apatite structure

Aug 1, 1996

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

By J. M. Jimenez, G. D. Schena, A. J. Cazorla

A full-scale Deister column was operated in parallel with the conventional cleaning bank of cells and a pilot Jameson cell in parallel with the conventional rougher cells. Flotation column performance was appreciably enhanced by use of an improved washing system and an internal launder. The performance of the rougher bank of cells, Jameson cells, cleaner cell bank and column were described by simple linear functions. These allowed calculation of overall circuit recoveries and evaluation of alternative circuits. An evaluation procedure based on a financial criterion is demonstrated with a simplified example, illustrating how revenues and operating margins are often of more concern than concentrate grade and recovery

Jun 18, 1905

By S. Kelebek

DETA exhibits a highly selective depressant action on pyrrhotite without adversely affecting the collectorless flotability of pentlandite and chalcopyrite in nickel-copper ores of the Sudbury region. A simplified Eh-pH diagram has been constructed to illustrate the extended stability of elemental sulphur and to explain the collectorless flotation of pentlandite and chalcopyrite. Cu and Ni ions, which are known to exist on the surface of pyrrhotite, promote the flotation of this mineral whether a collector is present or not. Thermodynamic calculations indicate that the action of DETA involves the sequestration of Cu and Ni ions from surfaces under a wide range of redox conditions; analysis of flotation test filtrate indicates as much as a 20-fold increase in the concentration of Ni and Cu ions. It appears that DETA may enhance the self-hydrophobicity of chalcopyrite and pentlandite by exposing more of the sulphur-rich surface sites for bubble contact in flotation. There are various possible explanations for its depression of pyrrhotite

Jun 18, 1905

By P. H. Carr, G. G. Marino, K. A. Patel

Extensions to a correctional institution at Wabash Valley, Indiana, required development over abandoned coal-mine workings, at 90 m depth, where subsidence was possible at surface. Backfilling of the flooded mine in critical areas was determined to be the most cost-effective method of limiting the risk of damage to the buildings. Containment grout was first placed in selected entries and cross-cuts of each mine area; the remaining volume was then filled with a readily flowing infill grout. Where a high proportion of an area was taken up by rubble, calcium lignosulphonate was used as a retarder and plasticiser to increase penetration. Grout movement was monitored from adjacent boreholes with an electrical resistivity probe during grouting, while after the work was finished core samples were obtained from verification holes drilled in the backfilled areas

Jun 19, 1905

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By G. M. Steed, A. O. Oyinloye

The deposit lies in amphibolite-facies biotite granite-gneisses of Proterozoic age, 4 km east of a major crustal break known as the Ifewara-Zungeru fault. Gold mineralisation is contained in a zone of quartz-carbonate (mainly calcite) veins and hydrothermally altered gneisses with associated small-scale intrusions along a steeply dipping second-order fault zone that roughly parallels the main fault. Gold is present mainly at grain boundaries between quartz and carbonate as discrete particles up to 100 micrometres in size, in general association with sparse, scattered pyrite, pyrrhotite and some base metal sulphides. Adjacent to the gold-bearing zone the granite-gneisses have been hydrothermally altered with minor volume increase, most notable enrichment being in K2O, S, Pb and Cu (and Au). High concentrations of Th, Y, Ce and Zr in the granite-gneisses imply derivation from S-type granites. It is likely that their high heat production capacity maintained the high temperatures needed to transport gold in the hydrothermal systems. It is most probable that the mineralisation dates from the Pan-African orogeny (650-450 Ma)

Apr 1, 1996

By L. J. Cabri, J. M. D. Wilson, R Lastra

An image analysis program can search for gold minerals in polished sections by scanning about 100 x 100 back-scattered electron images at a magnification of x400, allowing gold grains as small as 1 micrometre in diameter to be detected. Typically, a c.15 h overnight search of a product smaller than 45 micrometres will scan c.1 500 000 particles, providing data that are not easily obtained through manual operation of an optical microscope. The program locates grains of the correct brightness, acquires gold X-rays from them by wavelength-dispersive spectrometry, filters the data to remove artefacts and record the images and stage locations for subsequent retrieval. At the end of the run, the program allows the operator to verify and identify the grains found. Industrial studies at Canmet have included determining the nature of gold in cyanidation tailings, checking the mineralogy and size of gold grains in samples from an Indonesian Cu-Au concentrator and locating and measuring gold liberation and grain sizes in an ore

Jun 21, 1905

By F. T. Da Silva

Concentrates of titaniferous minerals containing around 30 wt% Ta2O5 are processed hydrometallurgically by hydrofluoric acid leaching and solvent extraction, followed by the precipitation of hydrated potassium heptafluorotantalate. A fundamental study of the thermodynamics of this precipitation and recrystallisation was undertaken to increase understanding of the conditions most conducive to the production of pure, well-crystallised K2TaF7. Activity-pH diagrams for the Ta-K-F-H2O system explained the dissolution of Ta2O5 in fluoride solutions quite well and also the precipitation-recrystallisation of K2TaF7.H2O. X-ray diffraction and scanning electron microscopy confirmed the thermodynamic observations. It was concluded that the best precipitating agent for K2TaF7 from fluoride solutions is KF but a recrystallisation step in a HF environment produces purer, well-crystallised K2TaF7.H2O, eliminating oxy-salts and other impurities

Jun 21, 1905

By J. E. Misiewicz, A Rozendaal

Paper presented at Geofluids '93, held in Torquay, UK, 4-7 May 1993. The tin field consists of a fragment of Lower Proterozoic volcanosedimentary rocks surrounded by granitoids. Almost all the significant deposits are hosted by arkoses and are classified as replacement and space-filling types, with particular styles of mineralisation dominating at different mines. Petrological and geochemical investigation of borehole cores from four centres indicated the presence of a stratified zone 500-600 m thick and continuous over at least 20 km along strike, consisting of pervasively altered clastic arenitic sediments. The alteration is zoned into a grey-green sodic albitised footwall, an 80 m thick sericitised-tourmalinised sulphidic tin zone and a red haematitic potassic hanging-wall. The zoning and the localisation of three cassiterite phases are consistent with the tectonic history and with multiple pulses of stanniferous hydrothermal fluids derived from late differentiates of the granites over a prolonged period. Areas of high fracture density acted as conduits for the fluids, whose initially rapid ascent was retarded by decreasing pressure contrast, limited development of fracturing and/or impermeable shaly arkose to cause lateral spreading and pervasive alteration over a broad, stratified front. Lateral overlapping of local fronts at the various centres suggests a continuous zone, while the many petrological and geochemical similarities point to a shared fluid composition

Aug 1, 1995

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905

By A. K. Tripathy, P. K. Pattnayak, H. S. Ray

The effects of water addition on the solid-state reaction between Cr2O3 and Na2CO3 at low temperatures (up to 873 K) were investigated to determine its possible influence on the reaction rate and the degree of conversion to soluble chromate. Experiments at high temperatures were conducted for comparison. It was found that adding water to the mixture before roasting enhanced both reaction rate and yield significantly. The reactions followed the Lesokhin-Tempelman equation at low temperature and the Ginstling-Brounshtein equation at above 973 K; the respective activation energies were 95 and 22 kJ/mol

Jun 19, 1905

By H. Y. Sohn, Hang Goo Kim

Computer simulations were carried out using calcium ferrite slags containing 25 wt% CaO, and the results compared with those obtained using fayalite slags. There was little difference in overall elimination of Pb and Bi, but elimination of Sb and As was much lower with calcium ferrite slag. When calcium ferrite slag is used only in the converting stage and fayalite slag in the smelting stage, as in the Mitsubishi process, the contents of Sb and As in the blister copper can be kept to reasonable levels. This allows advantage to be taken of the considerably higher iron oxide-holding capacity of calcium ferrite slag than of fayalite slag at the high oxygen potential under converting conditions, thus preventing precipitation of magnetite. Satisfactory agreement was obtained between predicted values and observed data from a Mitsubishi converter

Jun 18, 1905