Search Documents

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By I. Yu. Melekestseva

The Semenov hydrothermal sulfide cluster (13º31´N), consisted of five fields (Semenov-1, -2, -3, -4, and -5), was discovered in 2007 in the 30th cruise of R/V Professor Logatchev [Beltenev et al., 2007; 2009]. The hydrothermal fields are located on a seamount composed of ultramafic and mafic rocks, gabbro, plagiogranite, and their altered rocks. The Semenov cluster is considered to be the largest sulfide accumulation in the Ocean with massive sulfide (MS) resources of about 40 million tons [Beltenev et al., 2009]. MS of the Semenov-1, -3, -4, and -5 hydrothermal fields are mostly characterized by marcasite-pyrite composition whereas rich copper-zinc MS with high Cu and Zn contents (11.37?19.33 and 5.89?18.32%, respectively) and anomalous Au and Ag grades (22?188 ?127?1787 ppm, respectively) were dredged only at the Semenov-2 hydrothermal field associated with basalts (13°31.13´N, 44°59.03´W; 2360?2580 m of depths) [Ivanov et al., 2008].

Jan 1, 2010

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By M. E. Williamson

In September 2005 Williamson & Associates, Inc. delivered the BMS2 remotely operated seafloor coring system to the Japan Oil, Gas & Minerals National Corporation (JOGMEC). During acceptance trials aboard the JOGMEC research vessel R/V Hakurei Maru No. 2 the BMS2 successfully recovered 7.44 m of rock core in 3377 m water at a site near the crest of a seamount about 500 nm SE of Japan. Hydrogenous ferromanganese oxide crust, basaltic lava, sandstone and volcanic sediments were sampled with near 100% core recovery. The BMS uses rotary rod coring tools to collect samples to a maximum depth of 30 m in water depths up to 6000 m. Depending on bottom type to be sampled, the BMS tool magazine can be loaded with various drilling tools including core barrels with different bit types, drill rod and bore hole casing. The drill has 9 video cameras, a suite of sensors and 60 hydraulic functions powering thrusters, telescoping legs, seawater pumps and all of the standard drilling controls. The BMS provides deep water investigations with the functionality of conventional diamond bit rod drilling currently the mainstay of exploration programs in land mining.

Jan 1, 2005

By Boris Broere, Wiebe Boomsma, Pieter Lucieer

"The Blue Nodules project started February 2016 as part of the EU Horizon 2020 subsidy program. Blue Nodules aims at developing a sustainable deep sea mining system for the harvesting of polymetallic nodules from the sea floor. Blue Nodules is closely related to the Blue Mining and Midas projects, both EU subsidized projects. Blue Mining mainly concerned the development of technical capabilities to adequately and cost-effectively discover, assess and transport deep sea mineral deposits up to 6,000 m water depths. The MIDAS project - Managing Impacts of DeepseA reSource exploitation - was a multidisciplinary research programme investigating the environmental impacts of extracting mineral and energy resources from the deep-sea environment.The Blue Nodules project is divided in seven work packages defined to develop mining equipment and process equipment, to assess and integrate environmental, economic and technological aspects and to assess and minimize the environmental impact of mining polymetallic nodules.This abstract will address part of the work performed in the second work package called: ‘Subsea harvesting equipment and control technology’. The main topic addressed will be the development of a propulsion system to manoeuvre the harvesting system. The propulsion system will be developed with full incorporation of economical and compliance requirements and to have a minimal environmental impact.SummaryBased on information gathered in the 70’s during the first studies into polymetallic nodules mining and more recent data and developments, an initial full scale design of the propulsion system is developed. The largest challenge for the propulsion of a deep sea mining vehicle is to drive on the soft sediments associated with these deep sea environments. A short summary of the initial design criteria is given below."

Jan 1, 2017

By Tim J. Boyd

Gregg Marine, Inc. (headquartered in Signal Hill, California) has recently introduced an innovative seafloor drill system for offshore geotechnical site investigation and seafloor mineral exploration. The system is capable of working in water depths of up to 3,000 meters and is rated to drill to a depth of approximately 150 meters below mudline. The remote operated system integrates established drilling technology with proven Schilling telemetry and controls. The flexible nature of the patented wireline drilling technology enables the use of standard sampling systems (up to PQ-size core and 3? thin-walled tubes) as well as downhole testing systems (including CPT testing, vane shear testing, downhole sensors and borehole geophysical tools). The modular nature of the seabed drill system and the accompanying launch and recovery system (LARS) enables the use of local vessels of opportunity for projects resulting in reduced project costs and improved mobilization responsiveness times. Keywords: seafloor, seabed, geotechnical, drill, drilling, core, coring, sampling, CPT, cone penetration testing, borehole, logging, survey, exploration, ROV, remote sensing

Jan 1, 2011

By Richard H. T. Garnett

On the western continental shelf of southern Africa diamonds derived from onshore sources are concentrated in gravels within drowned terrestrial and marine geomorphological features. First discovered offshore in the late 1950's, they are known to exist for about 1400 km along the Namibian and South African coast in water depths of up to 200 m. Shallow water operations yielded 1.5 Mct during the decade ending 1970 when De Beers acquired a majority of the offshore leases and commenced a 15 year exploration program. Deeper water and the prevailing sea conditions required the development of new, unique, marine mining equipment. The first large scale mining production of 22 kct was achieved by De Beers in 1989 with an output of 22 kct. Annual marine output from all sources now exceeds 0.6 Mct worth some US.$ 170 M, and rising to 0.7-0.8 Mct for 1998. Exploration has also been taking place in the waters of West Africa, Australia, and Indonesia. Exploration is by means of high resolution geophysics followed by sampling using a variety of drills, airlifts and seabed-mounted machines which imitate the eventual mining process. Surveying is now probing depths of 500 m. Smaller scale mining by several junior companies has traditionally involved diving and airlift systems. Increasingly, however, they are adopting different and improved techniques which to date have been employed only by De Beers Marine as contractor to Namdeb. Marine exploration and unit mining costs are high compared to those applicable to alluvial deposits onshore. By 1996 the total development costs incurred by De Beers alone reportedly had exceeded US.$ 500 M. However, the financial rewards are commen-surate because of the higher recovered grades. The operations are not without risk for the total of nearly 10 large and medium scale production vessels deployed by various organisations. The greatest shortfalls are experienced in the estimated throughput, not the grade.

Jan 1, 1998

By Mikhail D. Ageev

The paper concerns with some questions of Autonomous Underwater Vehicle (AUV) control system design, which allows a motion at rough undersea terrain. The AUV advantages reveal itself completely during exploration of such objects as seamounts and reefs area. These objects are characterized by steep slopes (30 degrees and above) and chaotic situated obstacles (rock debris, pinnacles, escarpments). Uses of other technical facilities for operating in such formations are difficult, dangerous or impossible. These regions take an interest due to the presence of iron-manganese crusts. Modern AUV can estimate density of mineral by means of still camera or video recorder. For this reason the vehicle has to move with the distance of 3-5 meters from seabed. Under such conditions micro- and mesorelief presents a considerable danger for AUV. The AUV can bypass underwater obstacles in the various ways. However, in any case AUV motion will be characterized by intensive maneuvering on various speeds (from 0 up to 1.5 m/s), circular change of tractive force vector and, hence, a circular flow about the hull. So, AUV is equipped with the propulsion system, which provides free modes of motion.

Jan 1, 2003

By Virginie Tilot

Recommendations have been drafted following an international multidisciplinary panel discussion organized at UNESCO/IOC by the Académie des Sciences d?Outre-Mer on 15 December 2010 conveyed, according to its mandate, to the French government and to an international pool of scientists and stakeholders. These take into consideration the relevant Provisions of the United Nations Convention on the Law of the Sea of 10 December 1982, the Rio ?Earth Summit? Convention of Biological Diversity of 5 June 1992 as well as the activities and recommendations implemented for the world?s oceans and seas, in particular by the International Seabed Authority (ISA) and the recent reports and scientific works (including those implemented by the ISA Kaplan, Ifremer, COI-Unesco). The recommendations integrate, for one of the ecosystems, the conclusions of the project of the conclusions of an IOC-UNESCO / Government of Flanders project (2004-2010) implemented by Dr. V. Tilot from 2004 to 2010, during which were published three volumes describing the referential state of the polymetallic nodule ecosystem and proposing options for the management and conservation of the nodule ecosystem in the Clarion Clipperton Fracture Zone, NE Pacific Ocean: http://unesdoc.unesco.org/images/0014/001495/149556f.pdf, http://unesdoc.unesco.org/images/0014/001495/149556e.pdf; http://unesdoc.unesco.org/images/0014/001495/149556e.pdf#223

Jan 1, 2011

By H. Shimoda, K. Tamaki, K. Iizasa, M. Watanabe, K. Okamura

Modern Kuroko-type deposits occur in submarine calderas of island-arc fronts and back-arc rifts in Japan. They occur primarily on or adjacent to caldera boundary faults. Hydrothermal sulfides in the Myojinsho submarine caldera are one of Kuroko-type deposits, but their occurrence is different from other deposits found within the area 200 km2 around the Quaternary volcanic front of Izu-Ogasawara arc.

Aug 24, 2006

By Frans van Grunsven, Cees van Rhee, Geert Keetels

One of the obstacles during the initial phases of project development is the assessment of the environmental impact. Mining residue, consisting of fine seafloor sediments, are to be discharged subsea to mitigate the impact of these suspended particles. In order to test the effectiveness of discharging in proximity of the seabed, a numerical model is developed within the open source software package OpenFoam. Dedicated laboratory experiments for numerical model validation are discussed within this paper. INTRODUCTION Siltation is considered one of the major pressures on the environment for a seabed mining operation. Siltation is defined as the pollution of water by a high concentration of suspended sediments like clay or silt. This can be caused by two main activities during the mining process: the spill loss during the excavation and the return flow of undesired seafloor sediment after ore filtration on the ship. In a concentrated cloud, these fine particles form a so-called turbidity plume. Prediction of the size of these plumes and the created layer thickness of deposited sediment is a crucial part of the environmental impact assessment. The challenge in predicting the behaviour of these plumes is found in the wide range of scales involved in the process. At the point of origin, the turbidity plumes spread mainly under the influence of turbulent whirls created by an initial momentum and a buoyancy difference due to the presence of the suspended sediment particles. If carried by ambientcurrents, these plumes can spread for several kilometres before blending in the background.

Jan 1, 2018

By LeRon E. Bielak

Public Law 103-426 was signed into law in October 1994. Its provisions amended sections 8(k) and 20(a) of the Outer Continental Shelf Lands Act (OCSLA). The 8(k) amendment provides the Secretary of the U.S. Department of the Interior 001) with new discretionary authority to negotiate agreements for using Outer Continental Shelf (OCS) sand, gravel, and shell resources for certain projects of public benefit (e.g, beach, shoreline and coastal wetlands restoration that are under- taken by a Federal, State or local government agency). The new law also covers construction projects that are funded wholly or in part or authorized by the Federal Government. Under the law, the Secretary may assess a fee for use of the resource by taking into consideration the value of the resource and the public interest served. The law also requires that any Federal agency proposing to make use of OCS sand, gravel, or shell resources enter into a Memorandum of Agreement (MOA) with the DOI. An MOA would promote efficient coordination and resolution of inter- agency scheduling and issues. The law requires that Congress be notified before use is made of these OCS resources. The amendment to section 20(a) of the OCSLA clarifies that obligations concerning environmental studies extend to non- competitive lease situations and includes minerals other than oil and gas. The Minerals Management Service (MMS) is the DO1 agency responsible for interpreting and implementing the provisions of Public Law 103-426. The negotiated agreement approach is distinctly different from the competitive bidding requirements that have applied to all OCS minerals since the inception of the OCSLA. The MMS has opted to implement the new law in a nontraditional manner. Rather than issuinga body of new regulations to cover the negotiated agreement situation, or attempting to amend three sets of existing regulations, MMS is pursuing a less formal approach of providing guidelines. More weight is placed on the negotiation process itself and the legal agreement that consummates the process as the means for establishing ground rules, terms, and conditions under which qualifying projects may be conducted. This process must recognize and adhere to requirements of other laws, including the National Environmental Policy Act.

Jan 1, 1995

By Wonn Soh

As for Earth, where human beings live, approximately 70 % of its surface is covered by oceans. Today, advanced technology has led us to understanding the abyssal ocean floor through the use of submersibles and ROVs (remotely operated vehicles) for the last 30 years. Furthermore, the oceanic crust beneath the abyssal floor still remains an unexplored scientific frontier due to the lack of a direct approach. Exploration of this frontier is required to enhance our understanding of the mechanism of the M.8 class plate-subduction-type earthquake, of generation of the big tsunami, that caused the disaster, and of the paleo-global environmental change as well as of the origin of life as viewed in deep water thermal vents.

By Alexander Malahoff

A shipboard research system capable of operating in waters of up to 2,000 meters has been designed and implemented by the Hawai'i Undersea Research Laboratory (HURL) of the University of Hawai'i. It uses a remotely-operated ocean bottom survey camera system, an ROV, the Pisces V submersible, and a submersible emergency recovery system, all aboard the 222- foot R/V Ka'imikai-o-Kanaloa. All systems are operated from the stern of Ka'imikai with a mounted Caley telearm and articulated A-frame system. The system was designed for multipurpose use of the ship for launch and recovery of the Pisces V submersible on a lift recovery line (with or without diver assistance), or night-time operations with an electro-optical cable using either the HURL ocean floor sidescan or photo and video system operated at 10 meters above the ocean floor. The 1.14-inch diameter cable is also used to operate an ROV system. The garage/ROV system can also act as a submersible rescue system with a submersible lift capability. The ship is equipped with a SeaBeam and shallow penetration sediment profiling systems. This integrated system approach to deep ocean floor research will make it possible for HURL to carry out research pro- grams on seamount ocean resources and ocean chemistry and climate in Hawai'i and the equatorial Pacific.

Jan 1, 1995

By Ivo Dreiseitl

The interaction between nodule harvester and eupelagic sediment on the seabed is definitely one of the key aspects of mining technology for polymetallic nodules which is to be studied in details. Physical properties of sediments play major role for evaluation of protection and preservation of marine environment while strength properties of sediments will come in useful for future mining operations. Cone penetration test (CPT) used for testing in situ is one of methods for investigation strength properties of sediments. The testing apparatus for CPT consists of an instrumented cone having a tip facing down and it is mounted on special underwater equipment (rus. UGI-1). UGI-1 can determine subsurface strength down to the depth interval 0 ? 1.10 m. Special IOM geotechnical cruise was accomplished in 1989 on board R/V Academic A. Karpinski within the extra test area of about 1000 km2. Thanks to UGI-1 the IOM database recorded unique strength sediment data (cone penetration resistance) from 279 seabed points of sounding at profiles 125.6 km long. Up to 35 strength data from depth interval 0-1.1m (every 3cm) were obtained from any particular testing point. As a result 279 strength charts could be plotted (two examples in Figure 1). The cone penetration resistance values can be correlated to shear strength parameters.

Jan 1, 2011

By P. E. Mikhailk

From July 29 to September 15, 2004, the 178th cruise of the R/V Sonne took place under the KOMEX program in the Sea of Okhotsk. One of the cruise objectives was to dredge two different kinds of seamounts: 1 ? underwater volcanoes from the north slope of the Kurile Basin; 2 ? a seamount formed by tectonic (non volcanic) processes from the Kashevarov Trough. The underwater volcanoes are young edifices (0.84 ± 06 Ma, Baranov et al., 2002) with heights ranging from 150 to 300 m. Tops of the volcanoes are located at depth of 1260 to 2340 meters. The volcanic edifices are formed by olivine-clinopyroxene-plagioclase basalts. Dredge samples are covered by Fe-Mn crusts up to 40 mm thick. The seamount from the Kashevarov Trough is a tilted block. The height of the seamount is about 400 m and its top is located at a depth of 960 meters. Biotite hornfels, conglomerates, granodiorites, dropstones, and Fe-Mn crusts were recovered there. The thicknesses of crusts are up to 150 mm. Fe-Mn crusts from the underwater volcanoes differ from Fe-Mn crusts from the Kasevarov Trough seamount in morphology as well as in mineralogical and chemical compositions. The research was supported by the Program of the Presidium of the Far East Branch of the Russian Academy of Sciences (project ? 05-III-G-08-086).

Jan 1, 2005

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002

By Glen Smith

Nautilus Minerals, the world?s leader in exploration and development of deep ocean seafloor resources, is today focused on the recovery of high-grade copper and gold in seafloor massive-sulphide mineralization. These targeted mineralized belts, analogous to land-based volcanogenic massive sulphide deposits, are located near plate boundaries in the back arc basins of the Western Pacific. The first deposit to be developed by the company is located at a depth of 1,600 meters at Solwara 1, in the benign waters of the Bismarck Sea. This location lies within the territorial waters of Papua New Guinea. From 2006 to 2009 the company completed detailed environmental and geological studies at Solwara 1, culminating in a number of world firsts, including the first Environmental Permit granted for the extraction of seafloor massive sulphide deposits and the first NI 43-101 compliant seafloor massive sulphide deposit resource statement. Nautilus has relied heavily on proven deepwater technologies from the oil and gas industry in the design of its production system. Pipeline trenching units, workclass ROVs, deepwater production risers and drill cuttings removal systems will be adapted to initiate this new and exciting industry. Key contractors used by Nautilus on this innovative project have all been selected for their deepwater experience (gained in the oil and gas industry), creativity and determination to launch this new industry successfully. Innovation is at the forefront of Nautilus? success to date. This paper summarizes the progress to date of this development which will provide a new source of minerals for the world and which will contribute to sustainable growth for the future.

Jan 1, 2010

By J. R. Woolsey

The cost of an offshore exploration project is mainly dependent on the size of the vessel engaged for the work and increases dramatically with increasing size. Of the various factors influencing vessel size, the type and size of the sampling equipment is typically the principal consideration. This scenario is particularly true of shallow sampling programs employing a vibracore system. The problem develops when certain bottom materials such as densely packed fine sand require sampling. This type of material being one of the most difficult for the standard vibracore systems, with integral core liner, to penetrate to a reasonable depth of some five to seven meters. The problem is mainly related to the excessive cross sectional area of the cutting bit required to accommodate the core liner. The typical solution has been to apply more power to the vibracore drive head which results in a considerable scale-up for the entire system with attendant increase in vessel size. In order to reduce operating cost, M.M.R.I. has developed several systems for deployment from vessels in the 20 meter range. Two systems are modifications to the basic vibracore and a third is a vibralift system. Basically, one of the vibracore units is employed where core liners are required, utilizing a special jet bit designed to reduce the cutting pressure on the bit while not affecting the integrity of the core. The other designed for core extrusion on

Jan 1, 1986

By Peter M. Herzig

In September-October 2002, shallow seafloor drilling using the 5 m-Rockdrill of the British Geological Survey and the German R/V Sonne has revealed critical information on the sub-surface nature of two distinct hydrothermal systems in the New Ireland fore-arc and the Manus Basin of Papua New Guinea. Drilling at the summit plateau of Conical Seamount (39 holes, 31 % recovery) south of Lihir Island in the central New Ireland fore-arc has confirmed the sub-seafloor extend of previously discovered surface gold mineralization (up to 230 g/t Au) and associated alteration to a depth of at least 4.5 m below the seafloor and further proven analogies to the giant Ladolam epithermal gold deposit on Lihir Island. Drill core samples of clay-silica alteration contain average gold grades up to 14.2 g/t Au over a length of about 30 cm (fire assay Lihir Gold Ltd. laboratory) and appear to be part of a more extensive gold zone located below a carapace of relatively fresh ancaramitic and trachybasalt. These samples contain a complex mineralogy including realgar, orpiment, galena, sphalerite, some chalcopyrite and pyrite, together with amorphous silica, and possibly cinnabar. In addition to high concentrations of gold, shipboard analyses indicate that the gold-rich samples contain high values of Pb, As, and Sb, which is a characteristic feature of a magmatic-hydrothermal style of mineralization and alteration.

Jan 1, 2002