Search Documents

By Camilla Favaretti, Benjamin Turner, Anne Lemnitzer

Pile foundations are extensively used in the construction of various types of superstructures, including tall buildings, bridges, freeways and offshore structures. A fully constrained tip embedment such as a rock-socket offers an attractive solution for achieving significant tip resistance and improving the load-carrying capability of the foundation element. In profiles with very soft surficial soil, rock-socketing often provides the only reliable source of axial and lateral resistance. In preparation of a large-scale testing program on rock-socketed piles at UC Irvine (UCI) geared towards studying the magnitude of shear amplification at the rock-soil boundary of pile foundations, a pre-test model-scale experiment was executed in the UCI Structural Laboratory. The objective of the model-scale experiment was to iterate and validate the test setup, study the influence of important boundary conditions, assess instrumentation techniques and sensor placement, and to gain preliminary insight into the small-scale specimen non- linearity. In addition, this model-scale study provides ample opportunity to compare lateral performance parameters with analytically predicted lateral load behavior using traditional soil resistance functions and limit state analyses and explore new techniques for the derivation of soil resistance functions. The pile specimen had a pile diameter (D) of 10 inches and a total pile length of 125 inches. The pile was embedded in a 40 inch simulated rock socket overlain by 52 inch of medium dense sand (DR~50%). The pile extended 32 inches above the soil surface, where cyclic lateral loading was applied. The pile was installed in a laminar metal frame box with inside dimensions of 39 inches in width (W), 73 inches in length (L) and 86.1 inches in height (H) as shown in Figure 1. During testing, the box was restrained using a rigid bracing system consisting of concrete reaction blocks, wooden braces and steel girders.

Jan 1, 2018

By Alexi J. Neill

"This presentation will showcase two challenging projects with deep excavation support systems in the Atlanta area where state-of-the-art instrumentation and monitoring systems were used to manage risk by confirming design performance requirements / calculations during construction. The instrumentation and monitoring system successfully reduced risk by recording real-time data on a project website while simultaneously sending email alarms to key site personnel when data exceeded pre-determined alarm thresholds. The monitoring data revealed unexpected performance at an early enough stage so that contingency plans could be engaged and remedial efforts devised in order to limit the consequences. Finite element analysis was used to model deformations, analyze the unexpected performance, and prepare theremedial design.INTRODUCTIONConstruction in densely populated urban areas is becoming more common in order to keep up with the increasing infrastructure demands of our growing population. America’s big cities continue to outpace the overall nation in population growth. The city of Atlanta, the nation’s ninth largest city based on metropolitan population, is a prime example of this. The population has grown at a rate of 6.6% between 2010 and 2013, nearly triple the overall growth rate of the United States during the same period (SustainAtlanta, 2015).As a result of increasing infrastructure demands in Atlanta, developers are now constructing larger buildings on smaller properties. In addition, developers are attempting to maximize space on their selected properties, often by designing underground parking garages to accommodate as many cars as possible on these compact sites. In some cases the selected sites are adjacent to buildings, utilities, and other existing structures. The risk associated with construction increases during underground work that requires a support of excavation system, particularly on confined sites adjacent to existing structures. There is a risk posed to people, property, and the environment that the project team should monitor when constructing in these conditions."

Jan 1, 2016

By Ashutosh S. Dhar

Cast-in-place piles were examined in this paper from the viewpoints of construction quality, axial capacity, and load-displacement responses. The results of ten 450 mm diameter (18? f) bored piles, installed in a soil deposit of silt to medium dense sand using the method of percussion drilling, were tested under static loads. The results of the pile load tests were used for evaluation of various design methods of calculating pile capacity. The study revealed that the design methods based on the concept of critical depth underestimated the ultimate skin fiction. Thus, the applicability of the critical depth concept for design of bored piles under the soil condition considered may be unreliable. The estimated skin friction factor, ß, was too low in these methods. The Tomlinson method and the Neely method provided the best prediction of the ultimate skin friction. The methods used for calculating end bearing resistance were found to provide a conservative estimate of the resistance. During pile load tests, a settlement of 5 to 6 mm was required for full mobilization of skin friction for the piles in loose sand, while larger settlements (> 10 mm) were required for piles in denser soil. The ultimate skin frictional resistance was observed to be low for piles in loose sand.

Jan 1, 2006

By Zhitao Ma

The Cast-in-place Concrete thin-wall Pipe pile, referred to as PCC pile, is a new kind of pile for soft ground improvement. In this paper, firstly, the general introductions of the new pile technique, mainly including the technique principle, the structure of pile-driving machine, and the technological process were given, then based on the results of in-situ static lateral loading test, the pile lateral capacity, the relationship of load-deflection of pile at the ground surface, the lateral deflections versus depth and the soil reaction along the pile shaft were analyzed.

Jan 1, 2006

By Carlos A. Prato, Federico Pinto

"ABSTRACTThe design of drilled shafts often incorporates large factors of safety, for which settlements under service loads are highly influenced by the initial elastic stiffness. In the case of groups of drilled shafts with typical spacing, the elastic shaft-soil-shaft interaction dominates the behavior even for loads close to the bearing capacity, for which the initial stiffness is a key parameter in the design. This paper describes typical trends in results obtained by means of different approaches currently available in the literature for the evaluation of the initial stiffness of a single shaft. An experimental technique that provides a rapid and inexpensive means for the evaluation of the initial stiffness is described, and the results obtained for typical cases are compared with analytical predictions.IntroductionThe behavior of drilled shafts under axial loads is generally governed by the initial stiffness, as the factors of safety considered in design are often large, due to a superposition of conservative assumptions on soil properties and expected loads. In the case of shaft groups, the initial elastic stiffness plays a major role together with the elastic group effects, as nonlinearities tend to localize around the shafts and have a lesser effect than elastic deformations on adjacent elements (e.g., Leung et al., 2010). An accurate characterization of the initial stiffness is thus warranted for the analysis of drilled shafts and shaft groups under service loads.Initial stiffness of shafts may be estimated on the basis of soil stiffness and structural properties of the element by means of numerical methods (e.g., Pinto and Prato, 2006), as well as analytical methods (e.g., Randolph and Wroth, 1978). The soil stiffness may be determined by means of geophysical tests (e.g., Spectral Analysis of Surface Waves, SASW, Stokoe et al., 1994), or correlations with Standar Penetration Test (SPT) blowcounts or Cone Penetration Test (CPT) resistances (e.g., Sabatini et al., 2002).The initial stiffness may also be measured on drilled shafts by means of load tests. Static load tests (SLT), however, have some limitations on measuring small deflections, for which the initial stiffness is often extrapolated by means of large strain measurements (e.g., Chin, 1970), where the SLT measurements are more accurate."

Jan 1, 2014

By Cheng Lin

The Group Equivalent Pile (GEP) approach was proposed by researchers to analyze a laterally loaded pile group. This approach enables engineers to evaluate the behavior of a pile group in single pile analysis software, such as LPILE. A previous study showed that the calculated results using the GEP approach for piles agreed well with field test data. To evaluate the accuracy of the GEP method for analyzing laterally loaded shafts, two case studies with different shaft diameters were performed in this study. The comparisons showed that the calculated results using the GEP method and considering the contribution of the shaft cap if embedded generally agreed with the measured from the full-scale tests.

Jan 1, 2009

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By Jean Balech

This paper presents some results of dynamic loading tests performed on concrete piles driven in soft clay formation. The load transfer mechanism, measured in the dynamic increasing energy test (DIET), under blows of growing energy, is described in terms of mobilized normal forces diagrams and unitary local friction and displacements. It was observed that the lateral skin friction grows up to a maximum, in the soft clay layer and, gradually diminishes to a residual value when the system presents the maximum mobilized resistance. It may be concluded that the rupture load is not equal to the maximum mobilized point resistance plus the maximum mobilized local friction as suggested by most of static bearing capacity formulae.

Jan 1, 2002

By John C. Tosh, Peter M. Kandaris, Sheldon John

Geologic, geotechnical and hydrologic studies were performed for the design of 115 deep, large diameter drilled shaft reinforced concrete foundations (6 to 12 feet) to support tall steel monopoles for a new 13-mile long 230/69kV transmission line in southwestern Arizona. The subsurface conditions along the alignment posed a wide range of challenges for performing investigation and design studies. These conditions include saturated, loose granular flood plain deposits with generally low lateral capacity, potential ground loss up to 23 feet due to occasional river flow (scour and embankment loss), liquefaction impacts from nearby active fault seismicity that can generate magnitude 6.5-7.0 earthquakes, and unsaturated alluvial and eolian sand-dominated soils to full depth with low lateral capacity. All conditions will require significantly deeper than normal foundation embedment (depth ranging from 22 to 77 feet) and will present construction difficulty due to ground instability from groundwater and dry soil sloughing. A phased investigation was performed to accurately characterize the conditions for design and construction, and included performing a review of existing data, detailed field geologic reconnaissance, a limited number of standard exploratory borings (limited access), seismic cone penetrometer soundings (SCPT) in saturated soils to better understand liquefaction and strength loss potential, and hydrologic analyses to estimate scour/ground loss potential. This paper describes the site conditions, presents details on the investigation team’s approach, documents findings in relation to deep foundation analysis and design, and discusses recommendations for foundation construction to help in reducing risk.

Sep 8, 2021

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014

By Padmavathi V. Sagi

In this paper, effect of cyclic loading on the behavior of a long, flexible, unrestrained vertical pile loaded laterally in soft clay is examined. For cyclic loading, the analysis is carried out using a new method for the construction of p-y curves and for static loading conditions, p-y curves proposed by Dewaikar and Poonam (2005) are used. An iterative analysis is employed with secant modulus approach using a matrix method known as moment area method developed by Sawant et al. (1994). For pile top deflection of 20% of pile diameter, the load values are computed for both static and cyclic conditions. The comparison of results with the field test results reported by Matlock (1970) shows a good agreement. A parametric study is further carried out to examine the effect of load eccentricity, pile embedment length, diameter and the number of cycles on the pile response. The results of this study are discussed in the paper.

Jan 1, 2006

By Xu Youzai

Static loading teets of five nodular piles and four non-nodular piles were performed in Tianjin soft clayey soil in which measurements of axial force and movements were made. Distribution of shaft resistance and load-movment curves for pile head and pile toe are presented in this paper. The applicability of nodular piles to soft soil and their effectiveness are also discussed. Based on the comparison, it is concluded that nodular piles have an advantage over non-nodular piles mainly in contri­bution to shaft resistance. Dynamic testing was also conducted through R. P. T. for evaluating the service load of tested piles.

Jan 1, 1991

By Masanoub R. Fujioka

A brief discussion of the methodologies involved in dewatering practices, particularly as used in Hawaii in coralline formations. A description of early dewatering practices includes a number of case histories; later dewatering practices also are detailed with case histories. There were disasters and some successes. Grouting generally was not successful. Deep wells are technically feasible and generally the economical solution to deep basement construction.

Jan 1, 1986

By Laurel E. Blackman

The DFI Project Information Management Systems (PIMS) Committee cooperated with the US Army Corps of Engineers (USACE) to develop a specification for PIMS used on USACE projects. Once completed the Committee developed a more generic version of this specification for general use, which is contained in this document. This first edition has simply removed the USACE-related requirements from the document. The committee will continue to work on this specification to enhance the content and also incorporate recent technological development for these systems. It is the Committee's intention that a second edition will be issued in 2022.

Jan 1, 2021

By Kenneth Gavin

Design practice for piles installed in Irish glacial till has developed in an ad-hoc manner, based on the results of un-instrumented load tests. This had led to designers using similar design parameters for both CFA and displacement piles. To address the concerns of industry a series of instrumented pile tests were performed by two Irish Universities. These tests summarized herein, revealed that CFA piles develop higher shaft resistance than piles driven in glacial till. However, they exhibit low base stiffness and the end bearing resistance that can be mobilized at acceptable pile settlement is low. The use of simple non-linear elastic design approaches to predict the load-displacement response is considered. The methods are used to predict the capacity of two large diameter CFA piles installed in glacial till. While the predictions were reasonably accurate at predicting the initial load-displacement of the piles, significant creep settlement developed at higher load levels. The cause of the creep settlement was investigated through the use of plate load tests and the consequences for pile design are discussed.

Jan 1, 2009

By Chris Sammon

The Block 75 portion of the City Creek redevelopment project in Salt Lake City required multiple shoring walls surrounding the 6 acre site constructed to depths ranging from sixty-five to ninety feet below original street grade. Shoring for the project was challenging due to site soils consisting of cobbles, sands and gravels, interlayered lakebed silty clay and fine sandy silt with incised stream deposits of silty/clayey sand and gravels combined with a high groundwater table. Moreover, several abutting structures each with a unique foundation system would be directly or indirectly supported by the shoring system. Three sections of interest are the shoring walls constructed at Main Street, Deseret Trust Building and Eagle Gate Tower. Main Street shoring extended to as much as sixty-five feet below street grade and utilized existing basement walls anchored in place in the upper zones with soil nail walls with pre-installed vertical elements for face stabilization below. Data are presented which illustrates the effect dewatering had on the settlement of the Main Street Shoring. The Deseret Trust Tower shoring supported a 12 story, historical masonry building. Site conditions dictated a separate design for the east side and the north side of the building allowing comparison of relative performance between these walls. Settlements of this structure were controlled by installing micropiles through the 90 year old structures spread footings. Shoring for the Eagle Gate Tower was to be constructed immediately adjacent to a mat supported 22 story high rise structure. This shoring system combined secant piles, ground anchors and incorporated existing abandoned-in-place pipe piles with infilling high pressure jet grouting to create a cutoff wall and eliminate the adverse impacts of dewatering below this sensitive foundation.

Jan 1, 2010

By Kenneth A. Pidgeon

This paper presents a case history on mitigating vibration problems associated with the installation of steel sheetpiles. The project in-cludes installation of steel sheetpiles for a utility trench within 40 feet (12.2 meters) of a very sensitive manufacturing facility. Numerous production line quality control instruments and manufacturing processes within the manufacturing facility are extremely sensitive to vibrations. To minimize the impact to the owner, we specified that the contractor perform a vibration study using different types of pile hammers. The results and conclusions of the vibration study are presented in this paper.

Jan 1, 1995