Search Documents

By Clif Kettle

The paper will detail the design and execution of passive and active settlement control measures, the means adopted to overcome the various physical and operational constraints, and to meet specified allowable settlement criteria. The paper will highlight the close integration between the tunnelling and geotechnical contractors, designer, and Client, and demonstrate how particular practical difficulties were overcome by both the design and the construction methods.

Jan 1, 2008

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the ?strong? rock stratum, but did not correlate well with the design value calculated for the ?weak? rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2013

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Jeongbok Seo

The Dulles Corridor Metrorail Project (DCMP) involves the design and construction of a 23.1-mile extension of the Washington Metropolitan Area Transit Authority (WMATA) rail system. The initial 11.7-mile extension, with five transit stations and a new service and inspection yard, is to be constructed. The construction plan for the initial 11.7-mile extension includes installation of a total of an estimated 4,250 or 160,000 linear feet of driven 12x53 steel H-Piles at more than 80 different locations. At the time of this paper, approximately 40 percent of the piles have been installed and the remainder of piles will be installed by the end of 2010. This paper describes: 1) subsurface investigation program, 2) application of existing Codes and impact on the design of H-Pile, 3) design methods to determine geotechnical bearing capacity and pile tip elevation, 4) verification of capacity including PDA and Static Load Tests, 5) project specific pile load tests, and 6) QA/QC during pile driving.

Jan 1, 2010

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By Lance Helwirg

New high and low double outfall bridge structures for a juvenile fish bypass system have been constructed on the Washington Shore approximately two miles downstream from the Bonneville Dam on the Columbia River. The high and low outfalls each extend approximately 400 feet into the river from the Washington shore and are designed to release juvenile salmon into the river at above-water discharge elevations for improved survival rates. The two outfall structures include post-tensioned concrete double box flume girders approximately 7 feet high by 13 feet wide, which will be submerged in river flows as high as 15 feet per second. Each of the 6 offshore foundation piers is composed of a single 10-foot diameter reinforced concrete drilled shaft with a permanent steel casing embedded into the river bottom approximately 100 feet. Challenging outfall design conditions included designing the entire structures to be submerged for long periods of time in 15-feet-per-second river water flow with a 60-foot cantilever at the end of each outfall, and with the superstructure 70 to 80 feet above the river bottom. Figures 1-1,1-2, and 1-3 show the high and low outfall structure overhead photos and elevation view.

Jan 1, 2001

By Jesús E. Gómez

A total of 260 micropiles were installed as part of a retrofit effort for two existing bridges. The micropiles consisted of hollow core bars installed under limited headroom conditions. Of the total number of micropiles, 180 were installed in submerged sand and 80 were installed in stiff, silty clay. The micropiles were drilled using a lean cement grout which was re-circulated for de-sanding and re-use. Final grout was injected upon completion of drilling to the design tip elevation. The micropiles were subject to a rigorous quality control that included grout quality testing and proof-testing of each production micropile. This paper presents a description of the procedure for installation and quality control of the micropiles. The successful proof-testing of all the production micropiles showed that hollow core bar micropiles can be used effectively in granular and fine-grained soils. Hollow core bar micropiles offer particular advantages when installed in submerged sand formations with respect to other traditional micropile types. The results of the proof load tests are presented in a companion paper.

Jan 1, 2007

By Frank Albrecht, Brian McCarthy

"The Ararat Terminal Station (ARTS) is located 190km to the north-west of Melbourne, approximately 1.7km to the north of Elmhurst Township in the Pyrenees region of western Victoria, Australia. The site occupies an area of approximately 7.2 hectare of farmland. The electricity generated by the Ararat Wind Farm is directed to the ARTS terminal station before being connected to the grid. The ARTS structural design includes more than 180 steel yard support structures, three 25m-tall gantry ‘A’ frames, three modular control room buildings, a precast transformer bund, precast fire wall structures and related foundation design. Innovative driven engineered glue laminated timber (glulam) piles in a cruciform shape were used to reduce the foundation construction time, cost and the amount of concrete used in the project. It is the first time that engineered timber piles made from farmed Australian pine trees have been used in a large-scale environmentally-friendly project. Durability of the timber was achieved by H5 treatment and the use of reinforced concrete pile caps to protect the cruciform timber piles at the ground line. A pile-driving sequence was developed based on field trials. The lateral load capacities of the piles were estimated using engineering principles and from full-scale tests in the field. This paper provides an overview of details of engineered timber cruciform piles, durability of timber piles, design information, pile construction procedures, pile-driving procedures, the testing protocol, test results and validation. The test results were compared with predictions from several methods. In addition, potential future applications of similar systems in other infrastructure projects, and opportunities for future improvements are discussed. The structural aspects of this project were presented in a previous paper at the World Conference on Timber Engineering in Vienna in August 2016. See http://wcte2016.conf.tuwien.ac.at/home/ for further information."

Jan 1, 1900

By Quanchen Sun, Mohammed Z. E. B. Elsahife, Anthony Fisher, Chris Barker, Jennifer Schooling

A review of the literature shows that pile integrity is a significant concern in pile construction. Recently, a new integrity test, thermal integrity profiling (TIP,) has been put into use in foundation construction. It measures temperature changes and thermal profiles of concrete during curing. Heat generation and dissipation of early-age concrete is determined by the concrete mix, the ground conditions and the shape of concrete structure. The current data interpretation practice is primary based on experience. Anomaly detection through direct analysis of temperature profiles is currently indicative or suggestive and temperature signatures are usually similar, and numerous causes are not easily isolated. The core of the TIP testing technique, i.e. collecting detailed temperature measurements along the pile during the hydration process, is promising but a new interpretation approach is required. In this paper, a new interpretation approach has been developed in which TIP constitutes the first step. An investigative staged process is then followed to establish and assess the anomalies in the problematic regions along the pile employing the combined use of detailed finite element (FE) simulations, the actual temperature data from TIP and genetic evolution algorithms. In each stage, more details could be revealed about the anomalies being investigated including, ultimately, location, size and shape; this staged process enables practitioners to follow a riskbased approach and decide whether or not to pursue subsequent stages depending on the results they get at the end of each stage. This new approach, depending on the stages required for the analysis, will potentially avail practicing engineers of crucial test results about the quality of the pile immediately following pile construction, hence enabling repair and remedial work straight away at a lower cost.

May 1, 2022

By Gihan E. Abdelraham, Youssef G. Youssef, Mohamed M. Kamel

"Previous studies defined Narrow Mechanically Stabilized Earth, NMSE, walls as a retaining wall with aspect ratio (wall width to its height, L/H) less than 0.70 as in traditional walls. Some studies investigated its behavior and its failure planes compared to those of traditional walls. In this paper, parametric study using finite element analysis PLAXIS, 8.2 has been introduced to discuss global factor of safety, FS, maximum horizontal displacement, Ds, maximum tension force of reinforcement element, Tmax, and active earth pressure coefficient, ka, as a function of different aspect ratio of NMSE wall, L/H, reinforcing elements spacing, S, elastic axial stiffness of reinforcement element, EA, wall batter, 1/m, soil friction angle, f, and wall height, H. The results indicated that increasing aspect ratio increases the factor of safety, maximum horizontal displacement, maximum tensile force and active earth pressure. Increasing elastic axial stiffness increases factor of safety, maximum tension force of reinforcement element while decreasing the maximum horizontal displacement.IntroductionReinforced earth is a composite geoconstruction material, which embodies two basic components; namely engineering fill and reinforcing elements. The latter one is responsible for improving the tensile and shear resistance of the soil. The soil-reinforcement technique has been in use for many geotechnical applications especially MSE walls.A narrow wall system is referred to as a MSE wall with an aspect ratio, L/H, below 0.70 that is placed in front of a stabilized wall. An example of a narrow wall system with its dimensions is illustrated in Fig. 1."

Jan 1, 2017

By Martin D. Larisch, Ronald Damen

The design and construction of temporary working platforms for cranes and piling rigs is a high-risk activity. It requires the careful selection of the appropriate input parameters to obtain the correct load cases, as well as the application of robust and reliable design methods to assess the required thickness and stiffness of the working platform. The document introduces some of the most common and most relevant guidelines for working platform design which are currently used in Australia and New Zealand. The authors will also discuss the basic assumptions and considerations about load transfer from construction plant, debate ground risk, compare the applicability of different design methods for various ground conditions and suggest some common verification methods for working platform certification.

May 1, 2022

By Brad W. Taylor

"During the past several months, I have introduced to civil and structural engineers an innovative solution for the integrity testing of concrete using the Thermal Integrity Profiler (TIP) Wire Cable System by Pile Dynamics. While in the process of “educating” highly-trained professionals about a technological breakthrough, I ended up being educated myself about their needs for quality control/quality assurance (QA/QC). With that in mind, I would like to focus on their two key areas of concern:• How complex is the TIP installation process?• How does the QA/QC engineereffectively analyze and report TIP test results?A few months ago, during a discussion with a senior QA engineer, he asked a question that stopped me in my tracks: “Why should we do foundation testing at all?” Turning it around, I asked, “Why wouldn’t QA/QC personnel want to know everything they could about their critical infrastructure foundation?” Honestly, I didn’t answer his question nor did I fully comprehend what he was trying to say. With his experience, the engineer understood that there has not been an integrity test or a combination of integrity tests that could deliver an inside the cage and outside the cage (cover) complete data set that would provide a definitive profile of the entire shaft. Crosshole sonic logging (CSL) becomes more effective the larger the diameter of the shaft becomes, with a maximum effectiveness between 70% and 80%, but does not provide any data of the integrity of the shaft beyond a straight line between CSL tubes. Gamma-gamma logging (GGL) provides qualitative information about the concrete surrounding the GGL tube and device, and it provides information about a small percentage of the drilled shaft concrete near its outside edge."

Jan 1, 2017

By Mark R. Svinkin

"Construction equipment and operations usually produce soil and structural vibrations which may harmfully affect various structures and also the content of buildings and houses. The level of structural vibrations depends on a number of factors such as characterized sources of vibrations, soil conditions, and susceptibility of structures. There are certain knowledge and experience for managing the effects of construction vibrations which require implementation of condition survey of structures, information on construction dynamic sources and soil conditions at a site, evaluation of possible vibration effects on structure, calculation of ground vibrations before construction, use mitigation measures to decrease vibrations, and a choice of appropriate vibration limits. The paper presents the application of known concepts for assessment of vibration effects on structures from bridge constructions.INTRODUCTIONVibrations producing by construction activities such as pile driving, dynamic compaction of loose soils, demolition work, heavy construction equipment and trucks can affect adjacent and remote structures. Vibration effects on structures, sensitive devices and processes may create significant practical problems. Legal actions are often required for solutions of vibration consequences. The level of construction vibrations depends on dynamic sources, soil conditions at a site in particularly availability of soils with settlement potential, distances from the sources, parameters of waves propagating at a site and susceptibility rating of adjacent and remote structures. It is likely that intolerable structural vibrations from direct vibration effects of impact pile driving and resonant floor vibrations from vibratory pile driving may be induced in adjacent structures to construction sites.Foundation settlements resulting from soil vibrations in loose soils usually occur in the proximity of dynamic sources, but it is important that dynamic settlement may happen at various distances from the source. There are such examples. First, Kaminetzky (1991) mentioned a case history of building settlements developed at a distance of about 305 m (1000 ft) away from a pile driving site. Foundations of the buildings were underpinned on piles down to the tip elevation of the new driven piles to prevent building settlements. Second, Lacy and Gould (1985) shows that the peak particle velocity (PPV) of 2.5 mm/s (0.1 in/s) of ground vibrations could trigger dynamic settlements at distances up to 30.5 m (100 ft) from driven piles."

Jan 1, 2016

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015

By Stefan Schwank, Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to install diaphragm walls, which are known as underground structural elements commonly used for retention systems and permanent foundation elements as well as deep groundwater barriers, named Cut-Off-Walls (COW). In this exploration project, the diaphragm wall equipment was used in the 2019 summer season to perform the first part of an exploration and bulk sampling program for a potential mine on the Star Kimberlite. Beside the idea of using the diaphragm wall technique as bulk sampling equipment, the sampling program required the adaption of equipment and tools for a depth capability never reached before by a trench cutter in any commercial application worldwide. The paper will explain the development of the sampling program as well as the challenges occurred with the local geology and the specific demands of the exploration and sampling program. It will also provide an overview of the lessons learned during the 2019 season and will give an outlook to the approaches of optimization for the second phase which will be carried out in 2020.

By S. P. Lin

The numerical models of nonlinear piles for deep foundations are studied in this paper. The purpose of these is to clarify the mechanical behaviour of deep foundation nonlinear piles subjected to axial and lateral loadings. Based on the site data of p-y curve as well as t-z curve of foundation soils, it is possible to evaluate pile performance under above mentioned loads by means of combined FEM/FDM models. Numerical examples are presented in tall building and offshore jacket for illustrating the technique, it show high efficiency of these models. Some information to be interested by design engineers are given, especially for those who pay very concerns on the interaction behaviours of structure and its pile foundation.

Jan 1, 2010

By Carlandrea Albonico, Salvatore Miranda

The paper describes an innovative geotechnical engineering solution that has been provided within the scope of the Galataport Project, in Istanbul, Turkey. Among all interesting geotechnical works included in the Project, this paper presents the design principle, adopted technologies and performance controls related to the Multi- Purpose Bottom Plug (MPBP). This original geotechnical engineering solution has been employed for the deep basement excavation in Karaköy and consists of a combination of seepage control, ground improvement, and load bearing elements, which have been executed with double-fluid jet grouting, pseudo-elliptical jet grouting and permanent micropiles, respectively. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022