Search Documents

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022

By Louay Owaidat, Daniel Jabbour, Allan Frappier, Jose Gomez, Mark Stanley, Tino Maestas

The U.S. Army Corps of Engineers (USACE) is implementing a levee strengthening program along the Sacramento River East Levee (SREL) designed to correct 11 miles of deficient levees as identified by recent hydraulic and geotechnical investigations. The first project, the subject of this paper, completed in 2020 resulted in approximately 3.0 miles of improvements to the California Central Valley Flood Protection system. The project area lies along the east bank of the Sacramento River in Sacramento. The program consists of constructing cutoff walls through existing levee embankments to remediate levee through seepage and under-seepage. Key challenges included designing and constructing measures to remediate a 100-year-old legacy levee system, the presence of both industrial and residential properties immediately adjacent to the landside of the levee creating severe space and access limitations, and performing this work during the 2020 statewide mandate to shelter-in-place due to the COVID-19 pandemic. The project team of contractors, USACE, state and local agencies, and engineering firms partnered to bring this project to successful completion within budget and on schedule expending more than 60,000 man-hours with no lost time accidents. With the issuance of future planned contracts, the program will significantly reduce flood risk to the City of Sacramento.

Sep 8, 2021

By Aaron L. Sacks, David R. Good, Srinivas Yennamanda, Joseph K. Carey

Construction of Parcels 6 and 7, the second phase of The Wharf, began in 2019 and geotechnical construction was completed by December 2020. The overall project consisted of horizontal site, parks, and office buildings. The Wharf’s Phase 2 development includes approximately 1.2 million ft2 (110,000 m2) of above-grade construction including five multi-story, mixed-use buildings constructed over up to three levels of underground parking. The site is located between the WMATA Green Line Tunnels to the north and the Washington Channel to the south; it is bisected by a 108-in. (2740-mm) diameter DC Water outfall pipe. This arrangement, along with very difficult ground conditions, created challenges in the geotechnical design and construction. The support of excavation for this complex project required several different methodologies, including sheet piles, soldier piles, displacement piles, tiebacks, deep foundation anchors, jet grouting, and internal bracing with multi-tier rakers. Ground improvement was also required for support of spread footings in soft soils over the garage footprint. Underpinning of the active 108-in. (2740-mm) diameter DC Water outfall pipe running on a north/south alignment through the center of the site between the two garage structures was also performed. Since portions of the support of excavation are below the groundwater table, an extensive pre-excavation dewatering program was necessary and was separate from the foundation package. On the north side of the project, support of excavation (SOE) was required on a curved alignment, offset approximately 10 ft (3 m) from the outbound Green Line tunnel. Due to the proximity of the tunnel, a stiff, near-zero displacement wall was required. A portion of the buildings extend over the tunnels, imparting load to the tunnels to approximately restore original overburden loads excavated for the basement space. The building foundation is a 3 to 4-ft (0.9 to 1.2-m) thick mat slab anchored into the Potomac clay formation. Continuous movement monitoring of the tunnels was performed by an automated system. This paper describes the design and construction of the SOE and foundations for this high-profile project, which required collaboration between the Owner, Engineer, Construction Manager, and Specialty Geotechnical Contractor to solve many challenges.

Oct 1, 2022

By Renzo D. Verastegui, T. C. Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high rise towers in New York City. The 52-story condominium building is located on a 60 by 100 feet lot on East 60th Street between Park and Madison Avenues. The geographically complex site is bounded by two fragile 5-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City subway tunnel on the south. To add to this complexity, the ambitious development required 70 to 80 feet of excavation, mostly below groundwater level in highly permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 feet over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This paper describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.INTRODUCTIONThe project site is located at 45 East 60th Street, on the block bounded by East 61st Street to the north, East 60th Street to the south, Park Avenue to the east, and Madison Avenue to the west. As shown in Fig. 1, the site is surrounded on three sides by buildings sensitive to differential settlement. In addition, a NYCT underground subway structure lies below East 60th Street approximately 13 feet south of the site. The base of the subway structure is approximately 42 feet below the street.The project consisted of constructing a 52-story tall building. A portion of the superstructure cantilevers 24 feet over an adjacent five-story historic building. The underground construction for the new building involved a four-level basement, extending about 60 feet below ground surface. The excavation subgrade is much deeper than both the subway structure and the adjacent shallowly-founded building foundations."

Jan 1, 2016

By Michael Forrest, John Roadifer, Glen Gorski

"The Calaveras Dam Replacement Project (CDRP) requires large disposal sites to store excess excavated materials that could not be utilized for dam construction. Because of access restrictions during design, the disposal site rockfill toe dike area at the edge of the reservoir could not be explored to evaluate soil conditions. As such, the site had to be explored as part of the construction contract. Exploration revealed very soft clay and loose silty sand up to 40 feet thick that would not be able to support the rockfill dike at the toe of a large disposal site fill. Several alternatives were evaluated to stabilize these soils. Based on constructability, cost and risk considerations, cement deep soil mixing (CDSM) was selected as the preferred method of soil stabilization. The challenge was to design and construct the CDSM stabilization to minimize construction delays. A joint effort by the design engineer, construction manager and contractor achieved CDSM stabilization in about three months, from design through completion of construction. A rigorous quality control program included compression testing of both wet grab and cored soil cement samples to demonstrate that specified strength requirements were being achieved.INTRODUCTIONDisposal Site 3 (Figure 1) is one of the primary CDRP disposal sites having a height of 240 feet and a storage capacity of about 2,500,000 cubic yards. An approximately 40-foot-high rockfill dike at the base of the disposal site provides an erosion resistant toe for the disposal site. The rectangular foundation area shown in red was not able to be investigated during design because of access restrictions."

Jan 1, 2015

By M. Krzaninski, Y. Zou, A. Frost

The foundation solution for a data centre building in Sydney, Australia comprised two alternatives, the first of which incorporated the use of CFA piles founded in rock at approx. 27m depth to support column working loadings of approx. 7.5MN, and the second utilising rapid impact compaction with a raft foundation of 1.0m thick concrete slab. Soil conditions comprised 1m of fill over 3 to 4m of sands varying from loose to dense consistency, underlain by very stiff clays overlying the rock. A creative solution incorporating Rapid Impact Compaction to improve the loose soils in conjunction with a piled raft solution was proposed. Piles proposed under the raft were Atlas Drilled Displacement piles which offered advantages of displacement pile performance and savings in time and material costs. The piled raft solution was developed in consultation with the consulting structural engineer, combining the skills of the piling contractor and consulting engineer to the benefit of the project. This paper describes the development and design aspects of the piled raft solution adopted for the project.

Nov 1, 2022

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By A. David Miller, Chika Oya

"Field sampling and testing are part of the Quality Assurance/Quality Control (QA/QC) requirements for all Cement Deep Soil Mixing (CDSM) Projects. Field sampling and testing are also used for determining the performance and quality of soil mixing method(s) and are the primary basis for accepting or rejecting the soil mixing wall among all other QC testing. Two of the most commonly recognized and used sampling methods for CDSM walls are wet grab sampling and verification coring. Depending on the types of wall construction and project budget, one or both of these methods are normally used to help evaluate the in-situ matrix and quality of the mixed soils. Additional to ASTM strength and permeability testing from wet grab sampling and verification coring, more and more testing methods are being employed and accepted. However, these other testing methods tend to be unnecessary, lack consistency and repeatability, and are more subjective to manipulation and interpretation. In certain projects, there are also misconceptions involved with the results of wet grab sampling and verification coring, hence it is important to note how these wet grab sampling and verification coring work and represent the work in terms of quality of production.TYPES OF PROJECTSCDSM projects include (but not limited to) in-situ stabilization, liquefaction mitigation, excavation support, groundwater cutoff, and pollution containment. Although these projects use similar equipment on the jobsites, each project is treated differently in terms of catering to specification, uses of different mix designs, and emphasis on certain steps during production.Different types of projects with different specification changes the focus of quality, but soil types in jobsite also determine how to proceed with production. For example, a jobsite with predominate gravel layer must be treated differently as opposed to jobsite with clayey sand as the main soil type.WET GRAB SAMPLEWet grab sampling is one of the most used testing methods for QA/QC. The wet grab sample specimen is retrieved right after finishing the production of the desired element.Wet grab sampling equipment consist the use of 28 cubic inch (458.84 cubic cm) box attached directly to one of the auger stems. Hinges attached to the top and bottom of the box is fabricated to allow collection only during auger withdrawal. The collection box is strapped just above the mixing paddles on the auger stem and measured from the center auger head tip to confirm proper depth of collection. This box method has been used in Japan and U.S. for numerous projects."

Jan 1, 2017

By Michael Arnold, Jignyash Manyam, Yoav Rappaport

The USACE required construction of over 13 miles of cutoff wall at an average depth of 65 feet for the Herbert Hoover Dike (HHD). To meet project requirements, to provide quality control and make sound operational decisions, automated data capture, retention and visualization is crucial. Accurate and complete data management allows the authors to deliver critical business insights and to improve operational efficiencies. The author’s understood the necessity of capturing all their data, and efficiently processing and displaying it for multiple stake holders, for both internal and external purposes. The authors realized early in the project life cycle that data ownership and management is one of the fundamental features of the construction process. The authors developed their own software and use two in house applications; WEB-BGM online portal and, b-project which store rig production information combined with field quality control. b-project is used to create and deliver the Enterprise Database (EDB) to the USACE. Another biproduct of capturing the production data is the generation of the Geographic Information Systems (GIS) and also business analytics visual interactive display, developed through Microsoft Power BI. The paper focuses on the business process workflow and various technologies employed and lessons learned from the field operator perspective to achieve higher returns on business software operations.

Oct 1, 2022

By Giovanni Lombardi

In order to get a clear overview of the grouting works carried out, to avoid misinterpretations of the data and functions shown on the display of the grout monitoring device, it is recommended to keep the flow rate as constant as possible. Obviously, at the beginning of the process, the flow rate will increase from nil to the selected "basic" value. An important question frequently addressed is also how to reduce the flow rate in nearing the GIN limit so to finally reach the target intensity. Depending on the actual conditions, there are different manners to proceed. However, the following one appears to be the most convenient. It is represented on Figure 25. Being GIN the target intensity, two new limits at, let's say, 0.95 GIN and at 1.05 GIN as shown in the figure should be defined. The selected basic grout flow rate "q0", is kept as constant as possible all along the grouting process until the 0.95 GIN limit is reached. The flow is then reduced step wise to 2/3 q0, 1/3 q0 and zero at crossing each of the three limits. A similar rule can be used in respect to the maximum pressure, while for the maximum volume the process can be stopped at one time. Obviously the number of successive limits and thus the number of steps in reducing the pressure, as well as the width of the fringes defined in said way may be adapted to the local conditions.

Feb 10, 2003

By Paul M. Schuman, Alessandro Bertero, Giuliana A. Zelada, Sharon G. Cranston

Many jet grouted columns were recently installed to create a jet grout-treated soil foundation for an earthen embankment used in a large shoreline stabilization project in the Mystic River in Charlestown, MA. A physical test program was used to determine whether the jet grouting parameters the Contractor selected would meet the design requirements given the local soil variability, including soft river sediments and organic soils. The presence of hydrocarbons encountered in the marine sediments during the test program caused concern that the design strength could not be achieved. The published literature discusses the environmental aspects of jet grouting with hydrocarbons. The literature did not include many studies of the effect on jet grout-treated soil strength for the types and concentration of hydrocarbons encountered on this project. The grout mix, air pressure, and number of passes of jet grouting were varied in a second field test program to determine jet grouting parameters needed to achieve the design strength of columns with hydrocarbons. A geo-probe study was performed to identify the type and concentration of hydrocarbons on the site. With few exceptions, the quality control core samples from the production columns met the design requirements with many strength values far exceeding the design strength. This paper presents the data, and reviews the lessons learned. PROJECT BACKGROUND The Charlestown Bus Garage, located in Cambridge, Massachusetts, is a Massachusetts Bay Transportation Authority (MBTA) bus maintenance facility located on the Mystic River. The site was home to a coal gasification facility before it was developed by the MBTA as a bus garage in 1978. A deadman-anchored steel sheet pile bulkhead wall installed along the Mystic river on the east side of the site supports the site grade at about El. 11 ft (NAVD 1988) (Figure 1).

Jan 1, 2019

By Takeo Asanuma, Sachihiko Tokunaga, Hirofumi Taguchi, Yasuhiro Ootsuka, Yosuke Tanaka

The Cement Deep Mixing Method (CDM Method) is a ground improving method that has been used for mainly offshore sites to strengthen the soft ground below the sea bottom by injecting and adequately mixing cement slurry with soft soil into the ground to form a ground-improving column. In recent years, the CDM Method has increasingly been adopted for ground- improving work as part of liquefaction countermeasures and earthquake-resistant reinforcement in the shallow waters of river mouths and inland waters. In consequence of that, a pontoon-mounted CDM Method (CDM- FLOAT Method) has been developed for shallow waters, which is equipped with a land-type mixing machine combined with system management equipment and a tide level-based control function. This CDM-FLOAT Method can be deployed at work sites where the conventional offshore-use CDM barge cannot be employed. This report describes the CDM-FLOAT Method and the scope of applications together with construction work procedures, and a representative case of use of the CDM-FLOAT Method is introduced as an example of earthquake-resistant reinforcement of the existing embankment of a canal.

Jan 1, 2015

By Douglas R. Hardin, Stanley L. Worst, Joanna Mason

A challenging earth retention project presented itself in Washington, DC in the backyard of the historic House of the Temple (The Scottish Rite of Freemasonry, Supreme Council 33°). Located at 15th St NW and S St NW, a forty-foot-deep underground basement was to be installed adjacent to the existing Temple, a historic Carriage House structure dating back to the 1800’s and across a narrow alley from a four-story brick apartment building. The unique geology of the site included typical urban fill overlying a mixture of loose alluvial soils underlaid by dense marine deposits of the Potomac Formation. The clay, sand and gravel of the Potomac included nested boulders up to three feet in diameter. Design of the earth retention system accounted for ground conditions, installation methods and estimated movement of the system and adjacent structures. Anticipated ground water and unanticipated water from leaky sewers also proved obstacles to overcome during construction. Soldier beams were installed using a variable momentvibratory hammer to minimize disturbance to the historic and sensitive structures. Monitoring of the existing structures included both seismograph and optical targets during installation of soldier beams and as the excavation progressed. Micropiles drilled into the Potomac Formation were a part of the permanent foundation for the new structure. This local case history will delve into the details of the successful design, installation, and performance of an earth retention system and micropiles in a historic and highly congested urban environment.

Oct 1, 2022

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Robert Alperstein, Nidal AbiSaab, Joe Pastore

"This paper describes the design and construction aspects of the foundation support for a 57-story building currently under construction in lower Manhattan. The site is located near the East River with subsurface conditions consisting of about 40-ft [12.2-m] of unsuitable historic fill and soft plastic clay underlain by about 130-ft [39.6-m] of dense sand resting on bedrock. A mat foundation supported on unsuitable soils improved by jet grouting was selected for the project. Design concepts and selection of the engineering properties of the improved and natural foundation soils are discussed. The results of quality control testing and methods to verify design parameters during construction are presented.INTRODUCTIONNew York City (especially Manhattan) is known for its skyline of high rise structures. The geologic conditions in the New York Metropolitan Area influence the selection of foundations and feasibility of high rise construction as noted by Horvath (2013). These conditions include varying depth and quality of bedrock, multiple glacial events during the Pleistocene Epoch, and the effects of human modifications to the subsurface environment. Clusters of relatively taller buildings are generally located in Lower and Midtown Manhattan where sound crystalline bedrock is at relatively shallow depth beneath the ground surface and shallow foundations rest on the bedrock surface. In recent years the use of more costly high capacity driven piles or drilled caissons and deep basements has enabled the high skyline to spread to other areas."

Jan 1, 2016

By Takashi Enomoto

"The cement deep mixing (CDM) method has a wide range of applications, both on land and at sea. This paper describes the features of the equipment on CDM vessels engaged in maritime construction in Japan: the DCM No. 3 barge, the DCM No. 6 barge, and the DCM No. 8 barge. The DCM No. 3 barge is a large vessel with a mixing area of 5.7 m2. The design of the elevator of the deep mixing unit on the DCM No.3 barge enables us to conduct deep underground/ sea operations. This enables us to conduct mixing at depths of up to 52.6 m below the seabed and up to 70.5 m from the water surface. Additionally, since the tower is installed on the center of the barge, it has excellent stability. The DCM No. 6 barge and DCM No. 8 barge are mid-sized vessels with a mixing area of 4.6 m2. The DCM No. 6 barge was fitted in 2013 with energy conservation equipment and upgraded to an environment-friendly CDM barge. The energy saving upgrade used electric power, instead of hydraulic power, by inverter controlled alternating current motor for both mixing unit and main hoisting winch. This enables the using on effective use of regenerative power when the deep mixing unit is lowered. A feature of the DCM No. 8 barge is that it has an inclinable tower located at the bow section for elevating the deep cement mixing unit. Since the tower can be greatly inclined, the hull has a lower center of gravity and greater stability when the vessel turns. This also allows the vessel to pass below bridges and simplifies cruise preparations, outfitting and dismantling work.INTRODUCTIONThe cement deep mixing method (CDM method) involves mixing and stirring a cement-based solidifier into soft ground to rapidly bring the ground to the desired firmness. This method is used to suppress ground shear deformation, increase strength, increase slip resistance, and mitigate liquefaction and subsidence. It has been recently used in Japan in the construction of revetments at controlled waste disposal sites, both to boost the strength of the seabed and to prevent the seepage of waste matter and other pollutants. Undertaking CDM construction work at sea requires specially constructed marine construction CDM vessels. Since CDM construction at sea entails many more restrictions on working conditions than construction on land, the vessels themselves sometimes need to be modified. This paper will describe 1) the remodeling of the turrets and mixing machinery for mixing to great depths in deep water (DCM No. 3 barge with eight axes); 2) the upgraded of equipment on board CDM vessels after accounting for environmental considerations (DCM No. 6 barge with four axes); and 3) the use of a inclinable tower (DCM No. 8 barge with four axes)."

Jan 1, 2015

By James P. Chivilo, Gregory R. Meeder, Scott J. DiFiore, Matthew H. Johnson

New construction in metropolitan areas has direct impacts on immediate neighbors and abutters. While noise and dust are generally nuisance concerns, demolition, vibrations, excavation, and dewatering can cause structural damage to adjacent structures. Different cities, states, or jurisdictions have different regulations that dictate requirements, roles, or responsibilities for varying parties during construction. The authors will introduce and discuss risks of new construction adjacent to existing structures, and the legal framework in Illinois which requires the owner of the new construction project to provide adequate protections for adjacent existing structures. The authors, who are engineers and attorneys, will discuss technical and legal concerns, and will highlight the importance of early and frequent communication among project participants to manage risks, despite whether or not any local regulations exist to drive the process. RISKS IN ADJACENT CONSTRUCTION New construction in metropolitan areas inherently involves some combination of noise, dust, ground-borne vibrations, earth excavation, and subgrade dewatering. These issues have potential to directly and adversely affect abutters and their property. Noise and dust can be nuisance concerns, while vibrations, excavation, and dewatering can result in damage to abutters’ structures. Noise and dust are unlikely to lead to physical damage to abutters’ property, and can be controlled with limited work hours and good housekeeping practices. Vibrations and excavations, however, if not well understood, planned for, and mitigated, can result in serious damage to abutters’ structures. In turn, this damage introduces additional and often significant costs and schedule delays.

Jan 1, 2019

By K. E. Darnell

Drilled pier foundations have long been a favored foundation type for heavily loaded structures. Drilled piers derive their load-bearing capacity from end-bearing, and/or sidewall friction. This type of foundation is used in many geologic settings, including those areas underlain by hard carbonate rock, such as limestones and dolomites. When properly designed and constructed, drilled piers provide high load-carrying capacity in both compression and uplift. However, carbonate rock is often subject to intense differential weathering resulting in the formation of an irregular bedrock surface, sinkholes and caves; consequently, the investigation for, and the design of, drilled pier foundations is often complex. Further, the construction may be difficult and costly. This paper discusses geotechnical investigative procedures which can be employed to develop foundation design criteria and reduce the frequency of changed conditions. Finally, state-of-the-art construction practices and quality control techniques are discussed.

Jan 1, 2010