Search Documents

By G. S. Dobby, J. A. Finch

"I. INTRODUCTIONA significant development in flotation over the past few years has been the increasing industrial use of flotation columns, primarily in Canada. The column differs dramatically from conventional mechanical flotation machines, both in design end operating philosophy, which has been a principal reason for its slow acceptance by the mineral industry. Boutin, Tremblay and Wheeler (1. 2) developed the concept in the early 1960's and since then plant and laboratory columns have been marketed commercially by Column Flotation Company of Canada Ltd. In 1980-81 at Mines Gaspe, Quebec, three columns replaced 13 conventional cleaners in a molybdenum upgrading circuit, with superior results (3). Since then many of the copper producers in British Columbia have installed columns for copper and molybdenum cleaning, including Gibraltar, Lornex, Highmont and Island Copper. There now appears to be widespread interest in flotation columns.The column is particularly attractive for applications involving multiple cleaning stages and can upgrade In a single stage compared with several stages of mechanical cells. This results in simpler, more controllable circuits. Importantly, the column itself is well suited to computer control. A significant problem, however, has been that of translating laboratory data to plant performance. The purposes of this communication are to address the problem of column scale-up and to describe some of the transport mechanisms of a flotation column, leading to a kinetics based model.A schematic of a flotation column is shown in Figure]. Industrial columns are up to 13 m high and 0.3 to 1.8 m in cross section (either square or circular). Three zones can be identified:a collection zone, with feed entering 2 to 3 m below the top of the column and descending against rising bubbles generated at a gas sparger; a washing zone, where a packed bubble bed is generated by a downward flow of wash water; and a conventional froth (2 - 5 cm thick), the sole purpose of which is particle transport to the launder. The tailings withdrawal at the bottom of the column is controlled at a rate slightly greater than the feed flowrate (called a positive bias).An important element is the washwater, added just below the froth zone. The component of the washwater that flows downward (to make up the bias) is sufficient to prevent coalescence of rising gas bubbles. The packed bubble beg so generated is very efficient at suppressing gangue entrainment to the concentrate."

Jan 1, 1985

By V. N. Bryant

"1.0 SYNOPSISThe Colomac property, located 137 miles by air northwest of Yellowknife in Canada's NWT. will recover gold from 10,000 tons per day of open pit ore.The decision to proceed with the project was based on a mineable ore reserve of 16 million tons (including dilution) averaging 0.064 oz/ton. After an in-fill drilling program in the latter half of 1988, Colomac's mineable, proven and probable ore reserves were increased to 28 million tons averaging 0.056 oz/ton of gold.A feasibility study completed by Wright Engineers for Neptune Resources in December 1987 examined the possibility of vat leaching followed by C.l.P. and electrowinning. A second feasibility study completed by Wright in February 1988 demonstrated that a conventional agitated leach circuit using a finer grind justified the higher capital cost of this process. This study was accepted and formed the basis of the project authorization.Preliminary engineering commenced in April 1988 and detailed engineering was started in September of that year with the objective of a mine/mill start-up by early 1990.The short time period available to meet the project deadline was additionally challenging, as site access is either by plane year round, and winter road from early February to late March. Normal lead times for equipment design, specifications, quotations and bid analyses were not possible, if the winter road time-slot was to be met."

Jan 1, 1990

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

By Persio P. Rosario

Crushing has proven to be of fundamental importance in mine mill integration at Highland Valley Copper (HVC). Highland Valley Copper has achieved large throughput and good quality control through the gyratory crushers by proper blast design and better gap control. The next step, in optimizing the mine mill relationship, is evaluating the crusher liner wear and its shape influence on performance and product size reduction. To do this a laser measurement device has been developed and data is being recorded on the concave and mantle liner wear. This paper will outline the work to date and indicate specific objectives of the work.

May 1, 2002

By Yves Breau, François Robichaud, Jacques McMullen, Pierre Pelletie

"The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.INTRODUCTIONThe East-Malartic mill is located close to the town of Malartic in North Western Quebec, Canada. The mill was first commissioned in 1938. The flowsheet at that time was a straight cyanidation circuit. The original mill operated in that mode up to the discovery of the Bousquet 2 orebody in 1989 which consisted of a massive copper sulphide ore averaging 0.7% copper and 7 g/mt of gold. Bousquet 2 ore processing required a mill retrofit. Grinding capacity, gravity and copper flotation circuits were inserted prior to the cyanidation circuit in order to achieve 3,200 mtpd capacity at expected recoveries.In 1993, control of the flotation circuit was deemed critical in order to maintain the flotation performance and to reduce cyanide consumption since the copper sulphide contained in the Bousquet 2 ore is a high cyanide consumer (50% bornite). (McMullen, 1999) As a result, the implementation of advanced control strategies in order to increase the metallurgical profitability of the plant and to reduce the operating variability between operators was the most rational alternative. In 1994, Corem was chosen to perform the plant audit and to write the first set of rules. The on-line control strategy was started up in 1995. In 1996 and 1997 the Expert System was shutdown because of an extreme change in the ore coming from the milling of Bousquet #1 ore and the departure of the projects engineer. In 1998, the system was restarted and the results were impressive. Furthermore in May of 2001 a patent was issued for the control strategy. (Breau, 2001)"

Jan 1, 2002

By G. Couture, J. -F. Dubé, F. Letarte-Lavoie

"The Xstrata Nickel Raglan concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high-grade nickel ore, the plant’s current capacity is 1.3 million tonnes per year due to various optimization projects. In 2011 and 2012, the Metallurgical group, with assistance from BBA, updated and optimized the variables affecting SAG throughput in order to optimize process stability while maintaining maximum plant throughput. This project consisted of reviewing the control strategy and completely updating the pre-existing Fuzzy Logic controller. This paper describes the successful update of the controller including a complete revision of control rules, a new process control strategy and the integration of new process variables, most notably mill rotational speed. It will also show how this new approach has provided a simple and robust way of delivering both an increase in throughput while reducing process variability.INTRODUCTIONThe Xstrata Nickel Raglan Mine concentrator is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to treat 800,000 tonnes of ore annually. The Raglan Agreement held with the Makivik Corporation and the Inuit communities limits the annual tonnage of ore that can be processed at 1.32 million tonnes.The ore is processed in a 24 foot variable speed, semi-autogenous grinding mill (SAG). The conversion from Autogenous Grinding (AG) to SAG was completed in 2006. Before the ore is processed by the SAG, its size is analyzed by a Wipfrag camera that provides a granulometry estimate. A cone crusher reduces the SAG’s discharge screen’s oversize material. A 14 foot diameter ball mill ensures final grinding before the flotation stage.Many control strategies were used at the SAG over the past few years. Fuzzy Logic was first used in 2007 in order to control tonnage feed to the SAG. This first version only measured the value of the variables without taking into account their rate of change. Revisions were made over the course of the last few years to improve controller performance. Other variables were added such as slurry density and crusher Closed Side Setting (CSS). The previous revision of the Fuzzy Logic was done in 2009 with a review of the rules only."

Jan 1, 2013

By R. H. Walton

"In recent years the recovery of copper from low grade oxide ores has received widespread attention. The cost of treating such ores using conventional technology, such as milling and flotation, is frequently prohibitively high and copper recovery is generally low. The introduction of heap leaching, solvent extraction (SX) and electrowinning (EW) has resulted in high recoveries, good copper cathode quality and low production costs. This technology has now been successfully applied on a worldwide basis.This paper reviews the various process and design options and gives approximate capital and operating costs for a 1.0% copper ore.INTRODUCTIONAs a result of the low copper prices that prevailed for much of the last two decades, aggressive attempts were made by the industry to cut operating costs. Under such circumstances heap leaching, solvent extraction and electrowinning, to recover low cost copper from oxide ores, has received particular attention and ultimately widespread acceptance.Low grade copper ore (typically containing less than 1.0% Cu), which could not be economically treated by other methods, is placed on heaps and leached with dilute solutions of sulphuric acid. The copper rich, pregnant solution, drains from the heap into a collecting pond and is pumped to a solvent extraction plant where it is purified and upgraded. The resulting solution, termed the pregnant electrolyte, passes to the electrowinning section where the copper is recovered as high grade cathodes and sulphuric acid is regenerated, (Figure 1).This paper specifically describes the processing of copper oxides. Other copper minerals such as chalcocite and chrysocolla are also leached by dilute solutions of sulphuric acid. In practice the oxide minerals are frequently associated to varying degrees with less easily leached sulphides, such as chalcopyrite. In some cases, once the oxidized capping of the ore body is removed, the oxides are totally replaced by more refractory sulphides. Under these circumstances the leaching recovery is significantly reduced. However the principles described here for solvent extraction and electrowinning are also applicable to solutions received from heaps containing sulphide minerals, which are leached more slowly and involve bacterially induced reactions."

Jan 1, 1990

By G. R. Brough

"Today it is more important than ever to get the maximum possible return on capital invested in the processing industry. To this end the plant is often operated continuously and the choice of equipment is, consequently, extremely important.Screening spans a wide range of particle sizes and there are many different types of screening elements. The following types are common:1. Cloths and elements of rubber.2. Wire mesh screens with round wires.3. Wire mesh screens with profiled wires.4. Perforated steel plates.5. Elements of plastic.6. Gratings of steel beams.7. Gratings of iron rods.We would like to deal with two of these types namely rubber and briefly on plastics.We first introduced rubber screens to the Canadian Mining Industry in November, 1963. This stemmed from a conversation with the superintendant of one of Canada's largest screening plants containing 48 vibrating screens, with an average wire cloth life of 10 to 12 days. We contacted the manufacturer of rubber screen cloths who had supplied rubber screens to a mine in Northern Sweden for a 50,000 ton per day plant in 1951."

Jan 1, 1983

By Kevin O?Callaghan

Applying Legal Concepts - The Crown must consult, and where necessary accommodate, when: - Crown has knowledge, real or constructive, of the potential existence of Aboriginal rights or title and contemplates conduct that might adversely affect it - Duty to consult is triggered at a low threshold - How much consultation necessary? - Proportional to the strength of claim and potential impact - Spectrum: notice to direct involvement in decision making - Not duty to agree or to get consent (no veto) - Reciprocal: Duty requires good faith and sincere engagement on both sides Role of Proponents: Crown may delegate procedural aspects of its legal duty

May 1, 2010

By Gordan Marrs, O. Matwijenko

"The Kidd Creek metallurgical site has been highly integrated to maximize revenues from its base metals mines. The site's operations include a Concentrator processing 4.3 million tonnes per year of copper-zinc ore, a Copper complex producing 100,000 tonnes per year copper cathode and a Zinc Plant producing 130,000 tonnes per year of zinc metal. To improve operating efficiency with increasing emphasis on productivity, process control, process automation and process optimization have been augmented and expanded during the last decade.New microprocessor based control systems provided the opportunity for the capturing of an expanded number of process related measurements. As supervisory computers were already in place, databases could be generated with only increased disc space and database management programs required. Once the data had been accumulated and stored, a method was then required for handling, screening and sorting large volumes of information in relatively quick and easy terms in order that the stored information could be used. By 1984, a decision to use personal computers for accounting, engineering and management reporting provided the vehicle necessary to handle this data. Using commercially available software, large volumes of stored process data can be downloaded from existing databases, filtered, sorted, analyzed, graphed, displayed, projected, reported and distributed. All this can be performed in very little time."

Jan 1, 1989

Pressure for Better Safety Practices ? Increase Government Regulation ? Safety practices evolve from: ? Increased efficiency and performance ? More knowledgeable workforce ? Focus on decreasing risk to shareholder value In Order to achieve this ? Focus Points: ? Skill Development ? Best practices ? Situation-based decision making ? Enablers: ? Adoption of new technologies ? Transformed miner education ? Delivering on-demand information to the point of work Results: Miners empowered to improve mine safety

Aug 1, 2013

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By Robert Harris, Peter Pheeney

"The Murray Brook gold mine operated from September 1989 to March 1991. Approximately 1.2 million tonnes of gossan were mined from an open pit and treated at a rate of 900 tonnes per day. The facility applied an agglomeration vat-leaching cyanidation plant for gold and silver recovery. The leached ore or tailings were rinsed of residual gold and cyanide and placed on an adjacent clay lined pad for storage and containment. A 50,000 tonne heap-leach demonstration project was constructed at Murray Brook in 1992 to recover copper and zinc from ore located in a sulfide-rich zone occurring beneath the gossan. The operation proved unsuccessful because of poor recoveries and low metal prices. The project terminated in the same year.A corporate decision was made in September 1999 to undertake complete and final reclamation of the Murray Brook site. Jacques Whitford and Associates Limited were contracted to develop the final reclamation plan and to assist the company in presenting the plan to the New Brunswick government for approval. The government approved the plan in January 2000. Two important reclamation issues were the mobility of mercury from the gossan tailings and the potential of acid mine drainage from exposed sulfides. The mine site is situated upstream of a productive river system, and the issue or impact of chemistry changes to the environment over the long term became an overriding factor in the development of the reclamation plan.A resource assessment of the gossan tailings in 1999 indicated an average concentration of mercury of 40 ppm. The mercury occurred naturally as the mineral cinnabar, but the exposure to residual cyanide (less than 10 ppm) over several years in the pile has likely caused much of the cinnabar to decompose into more soluble mercury forms. The reclamation plan specified the replacement of all sulfides to the pit followed by approximately 600,000 tonnes of gossan. To ensure “fixing” of the mercury, the gossan was replaced in compacted lifts and both the remaining pile and that replaced to the pit covered with available till and compacted. The reclamation work was successfully completed in September 2000 and the chemistry of the receiving environment will be monitored over a three-year period, after which the company expects to achieve walk away conditions."

Jan 1, 2001

By J. S. Roberts

"Campbell mines has been in operation since 1948. Part of the process consists of roasting of a flotation concentrate which contains arsenopyrite.At present operation level the milling rate averages about 850 t.p.d. and about 48 t.p.d. of concentrate is roasted. The gas emissions at present contain between 3 and 3.5 t.p.d. of arsenic trioxide, about2 - 2.5 t.p.d. of particulate matter and between 19 - 25 t.p.d. of sulphur dioxide. The particulate is extremely fine calcine dust and it assays about 4 oz. Of gold per ton.Until 1974 the gas was discharged untreated through a 125' stack.UntreatedThe decision was made in 1972 to erect a gas treatment plant, construction ran through 1973 and operation began in 1974. The cost of the installation was about 1.3 million dollars.On investigation the process technology, it was apparent that the plant operated by giant Yellowknife for the same purpose was the model we should study. I would like to acknowledge the fine cooperation we had from giant, the plant that emerged is very similar to theirs and incorporates some improvements suggested by them and based on their operating experience.The plant is designed to remove arsenic and solid dust and it has no provisions to remove sulphur dioxide.We depend upon the 125' stack to assure adequate dilution. Because of the nearby airport the stack cannot exceed 125'. A stack burner is provided that can ""y used to heat the stack gas and carry it higher into the atmosphere when there is an inversion condition.The removal of arsenic from hot gas is fairly simple. The sublimation point is about 425°f, a few degrees above this point the arsenic is a gas and a few degrees below it condenses into a solid form. The arsenic could have been removed by simply dropping the temperature below the condensation point and collecting all the solids in a baghouse. This would have removed the possibility of recovering the gold in the calcine dust and would have produced an impure and more bulky arsenic material to be placed in safe storage. The decision was made to collect the solid dust in a hot electrostatic precipitator operating above the sublimation point and subsequently lower the temperature below the condensation point and collect the arsenic in a baghouse."

Jan 1, 1976

By Bill Mercer

The Triggers for PDAC Involvement in H&S ??Increase in serious accidents in mineral exploration in past few years ??Increasing junior role in exploration ?? Impression that there were few H&S protocols in place in smaller companies ??Lack of national benchmarking ?? The attitude that H&S is a provincial responsibility ??Corporate Social Responsibility initiative What is the issue in exploration? ??Mining?s reputation as ?dirty and dangerous? ??In public?s and media?s minds exploration employees are ?miners? ??In Canada, regulators often do not distinguish between ?exploration? and ?mining?. ??How does exploration compare to mining from a H&S point of view?

May 1, 2008

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

By Theodore H. Boggs

The battle of the gold standard is not limited to one country alone, or even to a single group of countries. It is being waged merrily in many important commercial and industrial quarters. Though it is not always a practical issue calling for immediate attention, it is none the less, quite widely, engaging the thought of bankers and other students of finance. The controversy arises, in the last analysis, because of the desire of men to secure a stable currency. There are two ways of restoring a reasonably stable currency system: (1) the re-establishment of the gold standard, or (2) the deliberate and artificial management of a paper currency. Both systems are well known. The gold standard was in use prior to the war in the principal commercial countries. A currency of inconvertible paper has been at times employed in the past in various countries; for example in Britain from 1797 to 1821, and in the United States from 1862 to 1879. The gold standard, as all are aware, implies the selection of gold as the standard of value. The unit of value is a fixed weight of gold and, so long as the standard remains unimpaired, all other means of payment are maintained at a parity with standard gold coins. And gold coins alone constitute the standard money, inasmuch as their value as bullion equals their value as coins. Under the gold standard this would not be true of any other form of money, although all other varieties of money, including bank notes, government notes and silver coins would be freely convertible into gold money. Strictly speaking, the gold standard also implies that the gold money in turn shall itself be freely convertible, through melting, into gold bullion and freely exportable.

Jan 1, 1925

By Joe Holmes, Peter Langlois

"Falconbridge’s Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region, has been in operation since December 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,000,000 tonnes per year. Optimization of the ABC grinding circuit has proven to be the most challenging component of this capacity increase. Concurrent flotation circuit modifications have allowed concentrate grades to increase from 16 to 18 percent nickel, while maintaining recoveries. Concentrate drying problems encountered during the first 15 months of operation have been addressed through equipment upgrades. The challenges associated with surface deposition of filtered tailings in an arctic environment are now better understood, and detailed design of the progressive reclamation cover is underway.GRINDINGCircuit OverviewOre from open pit and underground mining operations is introduced to the underground ore handling system via surface and underground truck dumps. Two underground bins with a combined capacity of 4000 tonnes provide roughly a day of live capacity for ore storage. Ore from the two bins is conveyed to a 150 tonne surge bin immediately ahead of the grinding circuit in the concentrator.The Raglan grinding circuit has a conventional ABC configuration (Figure 1) with a design capacity of 100 mtph (800,000 tonnes per year). The 24’ AG mill is powered by a 3000 hp motor with variable speed drive. AG discharge is sized on a 8’x16’ single deck vibrating screen, with screen oversize recirculating to a 5 %’ short head cone crusher (400 hp) before returning to the AG mill. Screen undersize is combined with ball mill discharge to feed up to 5 15” Krebs hydrocyclones. The ball mill is a 14’x 21’ overflow mill driven by a 3000 hp motor at 73% critical speed. Target Pgo for the grinding circuit product is 65 microns"

Jan 1, 2001

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By R. T. Jones

"Technical publications in the field of mining and metallurgy have existed for a long time. Recent developments in electronic publishing on websites make it possible to disseminate information more widely and cost effectively than before. Professional societies have an opportunity to serve their members and their industry by publishing high-quality peer-reviewed papers on their websites as well as in printed form. Older publications can be scanned, and optical character recognition can be used to provide searchable text. Various business models exist around this process. This paper outlines the approach used by the Southern African Institute of Mining and Metallurgy (SAIMM) to provide free open access to their journal papers and conference proceedings, as well as the work being done by OneMine.org to collect technical papers from a number of international societies and make them available to subscribers via a large database. An approach is outlined that should be of benefit to authors, readers, and society at large.INTRODUCTIONGeorgius Agricola (1494-1555) was not the first writer on the subjects of mining and metallurgy, but is well known as the author of De Re Metallica (‘of things metallic’ or ‘on the nature of metals’), a book that documents and illustrates the observations he made in the course of his extensive travels in the 1500s. Agricola wrote extensively about mining methods and metallurgical processes that were in place in the Middle Ages. The original Latin version of De Re Metallica was published in 1556, the year after Agricola died. It was translated into English by Herbert Hoover, a mining engineer and later President of the United States, and his wife Lou Henry Hoover, a geologist and classicist. The English version of De Re Metallica was published in 1912."

Jan 1, 2012