Search Documents

By H. Lachmund, R. Bruckhaus

At Dillinger Hüttenwerke/Germany steel production of grades for linepipe applications especially for sour service has a long tradition. The BOF process after replacement of the vessels is optimized by a newly developed lime addition model and variations in lance tip geometry. Equipped with three state-of-the-art VOD tank degassers metallurgical requirements of lowest contents of e. g. sulphur, nitrogen and hydrogen can be achieved. Three continuous casting machines of vertical bending type with solid core even improve already high levels of cleanliness. The vertical part corresponds to the metallurgical length of 12 to 15 m and therefore assures a maximum of cleanliness after solidification before bending. Slab thickness up to 400 mm can be produced with model controlled dynamic soft reduction. The accurate alignments of the casters assure minimized segregation and microporosity. Surface and internal cracks can be avoided by special cooling, bending and straightening strategies.

Jan 1, 2005

By Baoquan An

The energy required to fragment a rock is proportional to the increase in the fracture surface area and hence is proportional to the rock?s surface area. In comminution, the slope of the linear relationship between size reduction ratio and specific energy is usually defined as grindability. Another definition of grindability based on newly created specific surface area and specific energy is introduced. The two definitions for grindability reflect the grindability properties of rocks and can be used to measure of the efficiency of mills or crushers. The feed particle size distribution influences the energy needed to comminute the rock. For a given ratio of average feed size to product size, the smaller feed size requires more energy.

May 1, 2004

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By Thomas Mütze, Frank van der Meer, Gunnar Kretschmar

"The air classification of moist bulk materials is addressed in the literature insufficiently. Therefore a feasibility study investigated the influence of feed moisture on the separation efficiency expecting a reduction with higher moisture content in the feed. Two iron ore samples were characterized in terms of the nature of bonding of moisture as well as its effect on the agglomerate strength. The classification tests themselves were conducted with two dynamic laboratory air classifiers at cut sizes from 45 to 110 µm and a moisture of the feed material between 0 to 10 wt.-%. The quality of classification was assessed by split factor, cut size, separation efficiency, moisture of both products, as well as the yield of the fines as product fraction in a corresponding processing plant. An initial approach was found for a technological implementation: A sufficient drying of a moist feed can be realized simultaneously to the pneumatic transport inside the classifiers. In the present case the drying effect and dispersion intensity was sufficient to provide good separation results up to 3 wt.-% feed moisture. An additional drying step was necessary beyond 3 wt.-%.INTRODUCTIONSpecific information about the influence of moisture in air classifiers is very rare. Mostly only dry products are processed and/or drying prior to classification is recommended. Apart from the specific influence of the feed moisture a lot of literature can be found regarding air classification itself. Altogether air classification can be divided into several sub-process (Leschonski, 1977):- dosage of the feed material,- dispersing the solid feed material into a gas stream,- feeding the dispersed material into the classification zone by pneumatic conveying,- separation of coarse and fine particles, and- separation of fine particles from gas.For wet feed particles also drying plays an important role. Interesting for the present investigation are the humidity of the feed and its influence on the single sub-processes."

Jan 1, 2016

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994

By H. Pempel, J. Markowski, P. Ay

"Metal-coated thermoplastic parts find more and more functional and aesthetic applications in the interior and exterior of cars. The vapor-deposited or electroplated coatings are usually composed of a plurality of nickel- and chromium-containing layers, which are applied to copper-containing carrier layers on the polymers. Previously, recycling processes are mainly focussed at the recovery or thermal utilization of the plastics. Targeted and selective recycling of the metallic coatings is usually not carried out. Together with several SME, BTU developed a process, in which a complete and separate recovery of all components in high purity is possible with biotechnological methods. The bioleaching is carried out with iron and sulfur-oxidizing bacteria, especially Acidithiobacillus ferrooxidans. The copper-containing layers are dissolved in the solution; chromium- and nickel-containing particles are precipitated as solids. After the bioleaching, a mechanical separation of the individual metal-containing components and their separate workup are carried out. End-products are metallic copper, a nickel- and chromium-containing solid and the cleaned plastics. The bioleaching ensures a high purity of the end products. Through the use of bacteria, which are also found in nature, the process is environmentally friendly. Compared to chemical leaching using inorganic acids, considerably shorter leaching times can be achieved. In addition to the optimization of the leaching process, the R/D-project also includes the development and testing of the apparatus technology.INTRODUCTION The material complexity of many end-user products has increased in recent years, especially in the fields of electrical appliances, vehicle technology and medical technology. However, the demands on functionality, safety, comfort and energy efficiency still play a greater role in product design as factors such as sustainability and usability. For example, if a car still holds more than 70% of steel in the 1980s, a vehicle nowadays includes a larger proportion of a variety of difficultly separable plastics and composite materials, as well as complex metal composites. This relates in particular to composites made from such different materials as metals and plastics. The processing and recovery of the components of those complex material mixtures is difficult for recycling companies."

Jan 1, 2017

By C. C. Walden, A. Bruynesteyn

"Chemical and biological aspects of the formation of acidic effluents from sulfide waste materials are discussed. Test procedures to determine the acid producing potential of waste materials, as well as the characteristics of such acidic effluents, are presented. Practical applications of the test procedures are discussed with reference to predictior of environmentally unacceptable drainage and to estimation of metal recovery by dump leaching.INTRODUCTIONNatural leaching of sulfide minerals, exposed to the atmosphere, has been occurring for geological time. For centuries, man has been aware of the acid drainage originating from coal workings, copper mines and waste dumps. With the advent of the technical sciences, the processes involved in acid mine drainage production were considered to be solely chemical in nature. However, in 1947, it was shown (1) that a specific microorganism, called Thiobacillus ferrooxidans, was responsible for acid mine drainage from coal workings. It was demonstrated that under suitable conditions - this bacterium oxidized pyrite and marcosite in the coal to ferric sulfate and sulfuric acid. Numerous studies have subsequently demonstrated that - under suitable conditions - Thiobacillus ferrooxidans can attack most sulfide minerals, producing weak sulfuric acid, oxidizing ferrous to ferric iron and solubilizing other metals present (notably copper and zinc) as their sulfate salts."

Jan 1, 1980

By Norman O. Lotter, Dominic Fragomeni, Jorge Oliveira, Dee J. Bradshaw, Rebecca Monnapula

"The role of mixed collectors in enhancing the metallurgical performance of sulphide flotation processes was reviewed in 2008, and later published as an integrated theory by Lotter and Bradshaw, 2009. The theory proposed that xanthates, dithiophosphates and dithiocarbamates could be synergistically combined in an optimal formula to deliver improved grade and recovery. The approach uses a five-step structure, viz.1. A mineralogical study of the ore to be treated, identifying and quantifying the economic minerals (with hosting and association) and gangue species present.2. Selection of candidate collectors from this mineralogical information and from the known pulp conditions of that operation (e.g. Eh, pH).3. Design and execution of a factorial experiment to estimate and test the main effects and interactions, and to model the response surface for an optimum formulation [Box et al., 1978].4. Use of a High-Confidence Flotation Test platform in the factorial to reduce overall errors and allow for clearer observations [Lotter, 1995; Lotter and Fragomeni, 2010].5. Statistical design of a plant scale trial to measure and validate the gains [Napier-Munn, 1995; Lotter et al., 2009]. Eland Platinum, which was commissioned in November 2007, appointed a team to apply this theory to formulate an optimized mixed collector suite for use in the operation. The West Pit ore (UG2 - Normal ore) was sampled at site and brought to Xstrata Process Support, Sudbury, Canada, for mineralogical and metallurgical testing in 2008. Microprobe and QEMSCAN measurement characterized the type, grain size and textural association of the discrete Platinum Group Minerals (PGM) present. From the mineralogical data, it was clear that a mixture of dithiocarbamate and two xanthates would be a likely reagent suite selection. A factorially designed set of High-Confidence Flotation Tests studying these was performed, concluding that an optimal suite using certain amounts of these collectors was a viable formulation that would advance the grade and recovery performance at Eland above the standard PIBX by approximately 2.13% 4E PGE. The plant trial, which used a form of the replicated block design after Napier-Munn, 1995, and Lotter et al., 2009, exceeded this estimate with an overall PGE recovery gain of 2.48% (absolute basis) and a concentrate grade gain of 26.4 g/t PGE (absolute basis), as well as reducing chrome in concentrate from 2.04 to 1.62% (absolute basis). These gains proved to be statistically significant using the analysis of variance method, and have validated the theory."

Jan 1, 2011

By M. H. B. Nasseri

Barre granite?s samples have been tested for fracture toughness under mode I along two different directions with respect to microstructural fabrics were investigated. 3D objects counter algorithm technique is applied on micro CT images to identify physical properties such as crack induced porosity, crack density, generated total surface area and contribution of individual mineral grains within the damaged zone.The result obtained justifies very well the fracture toughness anisotropy in Barre granite, and explains the difference in the structure of the damage zone evolving as a result of test crack interacting with pre-existing microstructural fabrics. The present study has potential application in the fields of rock mass stability, oil reservoir stimulation, rock fragmentation and damage in blasting and emplacement of dykes.

May 1, 2009

By E. A. Lowe, J. W. Smith, C. W. Overton

"The operations of Bethlehem Copper are situated in the south-central interior of British Columbia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Columbia.The minerals are chiefly chalcopytite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies some pyrite is present. Average grade of mill feed is 0.55% copper.History of Milling Operations Production commenced in December 1962 at a rate of 3,000 tpd in a plant that comprised two-stage crushing followed by rod and ball milling. Production ratings were increased to 6,000, 10,000 and 12,000 tpd by the addition of a further stage of crushing and more rod and ball mills. When the last expansion was completed tonnage throughput exceeded the 12,000 ton designed rate and was stabilized at 15,500 tpd.However, recovery did not meet expectations at the expanded rate because of coarse flotation feed. Capacity in the rod mill circuits exceeded the subsequent fine grinding capacity, resulting in poor liberation. Studies were initiated to improve recovery without decreasing throughput.Description of Operation Prior to Pebble Milling Crushing with primary, secondary and a closed tertiary stage proceeds at a scheduled 20.5 shifts per week. Fine ore screened on 1/2"" x 4"" apertures is stored in a 30,000-ton bin ahead of two 12.5' x 15' rod mills. Rod mill discharge joins secondary ball mill (one 10.5' x 14' and one 11' x 14') discharge for classification in a single 50"" cyclone which closes the secondary mills. Overflow from this cyclone is split between three third-stage ball mill-pump-cyclone circuits (two 11' x 14' and one 12.5' x 15'). Prior to addition of the two pebble mills the flotation feed was produced by this three-stage grinding system. Grinding criteria are shown in Table I."

Jan 1, 1975

By H. Ewaschuk

"INTRODUCTIONRio Algom's Stanleigh Mill in Elliot Lake began production in June of 1983. The highly instrumented mill treats uranium ore at an average rate of 3900 metric tons per day. To help ensure a good start-up and low operating costs, an extensive training program was undertaken prior to and during start-up. This presentation describes how an unconventional operating crew were combined to form an operating unit with a high efficiency in terms of production and labour utilization. I would like to point out at the outset that the operating philosophy, and the role of the supervisors and the operators as set up at Stanleigh is not unique. Indeed, I have seen the same results at a couple of small plants where efficiency meant survival. However, these situations appeared to be the exception, and it was not readily apparent how similar results could be obtained in a larger plant. A factor that existed at the time was low labour turnover. As in most parts of Canada, jobs were easy to get in the Elliot Lake camp in the late 1970's. This, and other factors, contributed to an unusually high labour turnover. This changed dramatically in the early 1980's. Indeed, Rio's two other operating mills, Quirke and Panel reduced crew sizes at this time to reduce operating costs. As a result all of Stanleigh's operators came from Quirke and Panel with experience varying from 4 to 7 years. The experience that operators had was obviously of benefit and served to reduce the scope of the training program from what would have been required with inexperienced personnel."

Jan 1, 1985

By Emilie S. Williams

The Doyon Mine?s Zone 1 (Altered Zone), found along the southern boundary of the mine, encompasses approximately 20% of the mining reserves. The mineralisation is found in a series of steeply dipping narrow veinlets, which are contained in an extremely weak host rock: a sericitic schist with RQD values ranging from 0 to 20. Longhole mining methods are used, with either longitudinal or transverse approaches, depending on the width of the ore zone. Dilution is of critical importance in the mining of this zone, particularly in longitudinal stopes, where dilution levels have averaged 55% since 2000. Major factors influencing dilution in this zone include the stope geometry and standup time. A two-phase approach has been developed to mine and backfill longitudinal stopes: the top of the stope is pastefilled after approximately half of the broken ore has been extracted; the remainder of the ore is extracted once the plug has cured; and the remaining void is filled. This method has been used in six stopes to date, resulting in an average dilution of 17%. This paper details the application of this technique and its effect on dilution.

Oct 1, 2004

By Paul J. Cascone

This paper will discuss the science behind the development of a unique gold alloy for dental prosthetic applications. The alloy (GOLDTECH BIO2000) contains 99.7% gold providing unquestioned biocompatibility and unsurpassed esthetics. The topics discussed are: (1) How the alloy meets the functional requirements of a porcelain-fused-to-metal dental alloy. (2) How the alloy color affects the esthetics of the restoration and why the color of gold is best. (3) Overcoming the intrinsic malleability of gold when grinding the alloy surface. (4) Preventing the oxide color from interfering with the alloy esthetics. (5) Attaining excellent porcelain adhesion. (6) How the design of the restoration allows for the production of single and multiple unit restorations. Gold 2003

Oct 1, 2003

By Peter Wells, Laxman M. Amaratuga, Todd M. Kanhai

"Certain mining methods (eg. Cut-and-fill) result in the contamination of run-of-mine ore with shotcrete. This shotcrete remains mixed with the ore throughout processing. Experimentation performed by Falconbridge Limited revealed that underground contamination of ore by shotcrete (eg. as little as 1% by weight) has led to ill-effects on the nickel recoveries from the flotation process in the mill. The nickel recoveries of contaminated samples were lower than tests without the shotcrete Contamination.To optimize flotation circuits it is important to know why the contamination has created these effects and also to find a method to abate or remove them. Laboratory testing showed that the age of the shotcrete was a factor in it’s effect on nickel recoveries. Younger aged shotcrete gave nickel recoveries lower than baseline nickel recoveries with no contamination. Older shotcrete gave nickel recoveries similar to the baseline.Literature on other cementitious material contaminations on ore revealed that a possible means of remediating this problem is the use of acid in the flotation. The initial pH in the flotation pulp was designed to be pH 9.2, but with the young shotcrete contamination the pH was in the neighbourhood of 10.5. Acid addition may act as a means of lowering the pH to the optimal operational value. Laboratory test work showed that acid addition brought nickel recoveries closer to the baseline."

Jan 1, 2000

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hard rock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

May 1, 2007

By I. Jackman

"Gold is present in different forms and associations in different ores. Flotation is used to recover gold and minerals associated with gold, but the applicability and type of flotation vary. The purpose of flotation in a gold recovery plant is largely dependent on the mineralogical association of the gold, and environmental and economic considerations. In this paper, the role of flotation in the recovery of gold is reviewed. The paper will describe examples of gold recovery by flotation including flotation of native gold, gold associated with sulphides including specifically copper sulphides, gold associated with tellurides, gold ores containing carbonaceous material and gold contained in tailings.INTRODUCTIONFlotation is widely used in the recovery of gold. However, the objectives and the mode of application are quite variable dependent on the type of ore, the gold association(s), other metal values, marketing considerations and environmental requirements. In this paper, a range of different applications of flotation incorporated in the recovery of gold are discussed. The reasons for each particular application are outlined and metallurgical results are presented.The mineralogy of the ore and the gold associations are fundamental influences on gold recovery. The use of flotation to concentrate gold is dictated by the mineralogy of the ore and gold. The fundamental factors are mineral/gold size, liberation size, association of the gold and type of gangue minerals or other valuable minerals. Gold can exhibit a range of sizes in a host from relatively large size (+50 µ) to refractory size (1 µ and sub-micron size). Similarly, the gold can occur in a number of phases in the same host. For example, the gold was present as petzite (AgAu telluride), calaverite (AuTe2) and native gold in a gold telluride ore and each of these minerals was associated with the pyrite host.Understanding the gold mineralogy and association is important in establishing the correct process route. The gold mineralogy is established by good mineralogy, use of diagnostic tools such as diagnostic leaching and assay by size fraction analyses and basic metallurgical testwork."

Jan 1, 1995

DynoMiner APS Delivery Systems Overview ? New Design of DynoMiner APS-M2 ? Stand alone or attach to Cargo type 10,000 lb (4536 kg) emulsion bins. ? Hose reel w/200-ft (61-m) by 1-inch I.D (25-mm) hose capacity, power rewind. ? Increased water and trace capacity. ? Hose reel and gassing offered as options. ? New Flow Meter ? DN-100: aluminum body, UHMWPE rotors. ? Will be offered as an option. ? APS Nomenclature ? Proposed changes ? DynoMiner APS and APS-M1 to become DynoMiner APS Drifter ? DynoMiner APS-M2 to become DynoMiner APS Stoper. ? Both to have optional gassing / flow metering.

May 1, 2004

By Norman O. Lotter, Simon Yu, Tony Deng, Antonio Di Feo

"Xstrata Nickel’s Raglan operation, northern Québec, achieved paymetal recovery gains in 2007 by switching the collector from potassium amyl xanthate to sodium isobutyl xanthate. To follow on from that position, Xstrata Process Support (XPS) and A. Di Feo of Raglan proposed that a mixed xanthate system be formulated and tested towards further performance gains. This work selected ethyl and isobutyl xanthates as the candidates. An optimized ratio of these was to be determined by a designed experiment. This suggestion was based on an abundance of published literature that reported mixed collector systems outperformed single ones. A partial factorial design was used to configure four test conditions and a mid-square for the flotation work. The testwork was conducted using High Confidence Flotation Testing. The raw data were analyzed and modelled by Design-Expert software. An optimum ratio of 1.6:1.0 by mass (1.32:1.0 in molar terms) of isobutyl:ethyl xanthate was determined. Without this modelling, the optimum ratio would have been missed. Results obtained with the new baseline flotation test using this optimized mixture showed a 3.3% Ni recovery gain in the bypass concentrate and more than 1% recovery gain for PGM over the single PIBX system. This system has been proposed for and accepted as a plant scale trial in the first half of 2010.INTRODUCTIONConcentrator OperationsMilling and flotation of sulphide ores ahead of smelting and refining is a common practice. This choice results in the larger and more variable paymetal loss in the production of saleable metal [Cramer, 2001]. For this reason, it is common to see an ongoing performance improvement programme at the operations level. When successfully performed, these e"

Jan 1, 2010

By S. Haggarty

"Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Milling capacity is 3,400 SDT /Day with an average feed grade of 0.080 Oz Au/Ton. Gold processing involves three stage grinding including tertiary pebble milling, two stage cyanide leaching and filtering and Merrill-Crowe zinc precipitation.A summary of process improvements required to increase milling capacity above the initial design tonnage of 2, 700 SDT /Day are described -Installation of a 42"" x 65"" Allis Chalmers Gyratory crusher replacing a 42"" x 48"" Traylor jaw crusher.Installation of polyurethane screen panels replacing woven wire cloths on an 8' x 20 ft triple deck screen.Installation of a hopper clarifier to reduce filtrate turbidity.Automated control of solution balancing and effluent treatment circuits.INTRODUCTIONThis paper describes mining and milling practices at the Nickel Plate Mine and details post start-up process modifications which were required to attain design tonnage.Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Mining capacity from the open pit is approximately 32,000 TPD with an average waste/ore ratio of 8.4:1.Milling capacity is 3,400 SOT/Day, above initial design tonnage of 2,700 SOT/Day. Feed grade averages 0.08 Oz Au per ton yielding 85,000 troy ounces of gold per year."

Jan 1, 1991