Search Documents

By G. W. Diehl, G. A. Griffiths

"Gentlemen, one week ago, I attended the University of Minnesota's Annual Symposium on Mining, in Duluth. A good part of this symposium was dedicated to mill linings of rubber.At this symposium, three mining companies published results from long time full scale tests with rubber linings in mills at four different mines. These were the Republic and Empire Mines of Cleveland Cliffs Iron Company, the Groveland Mine of Hanna Mining Company and the Eagle Mountain Mine of Kaiser Steel Corporation. These papers will be printed in due time and I will not endeavour to relate their full contents, let me only say that in three of the plants, the linings were found to be very economical compared wi.th steel, and that these three are converting over completely to rubber linings, while the fourth, Empire Mine, reported no economical results as far as the shell lining goes, whereas the grates showed promise of becoming economical. The authors of the Cleveland Cliff's paper, however, stated that design improvements in the rubber lining possibly could result in an economical lining also for Empire Mine.That rubber linings in mills, in most cases, show better wear life than steel linings, is known by most of the audience. But, one thing that has not before been disclosed by the endusers is the effect of rubber linings on the grinding economy. All three papers mentioned above reported no change in capacity or grind and two of them reported a decrease in power consumption per ton ground. Hanna Mining reported an average decrease over a three year period for one mill of over 10%. This, of course, puts the economy of a rubber lining in a completely new light. Finally, a point of interest at this meeting was that all three papers emphasized the design aspect, Thus the industry has acknowledged what I believe to be a very important fact - the design of a lining is often more important than the material it is made of."

Jan 1, 1970

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014

By M. Sider, D. L. Piron

"The cost of energy is a growing factor in the cost of zinc production. Electrowinning from sulphate solutions with periodical reverse current or from acidic chloride or alkaline solutions could be the way to lower costs. A comparison of the energy consumption for electrolysis shows that the alkaline solution may be considered the most promising alternative. IntroductionZinc electrowinning from sulphate solutions is a very energy intensive process (typical specific energy usage : around 3.1 kWh / kg zinc). This energy consumption represents 35% of the total cost of electrolysis and is the most important cost component.In order to lower costs, the energy efficiency of the sulphate process should be improved or alternative processes should be developed. In this laboratory, that objective has resulted in research on electro winning in sulphate solutions with the use of periodical reverse current (PRC) and in acidic chloride and alkaline solutions.Some of the results obtained in this laboratory and already published and new experimental results reported in this paper make it possible to present a more critical comparison of the energy consumption of the three processes mentioned.ExperimentalThe experiments at constant current were carried out as described previously. Specific conditions are indicated in Table I. Current efficiencies were obtained by weighing deposits.ResultsThe best energy consumptions for electrolysis obtained in this laboratory for the three media are presented in Table I. More detailed results can be found in the papers already mentioned."

Jan 1, 1988

By D. T. Aikens, R. Gaudreault

"This paper summarizes structural repairs carried out on a marine wharf consisting of six 13.7 m by 13.7 m reinforced concrete cribs linked together by five 14.6 m long beam spans. As a result of problems during original construction and twenty years exposure to severe weather conditions, the deck support system between the cribs required major restoration work. In particular, some of the beam seats under the crane rail supports had marginal bearing area to support the structural loads. Faced with closure order for the wharf which is required to bring in raw materials to the plant and a long outage to make repairs as stipulated by Ports Canada (owners of the structure) alternate means of making the required repair were examined.The method chosen allowed the work to be done much more quickly, at lower cost, without taking the wharf completely out of service. The badly deteriorated seats were rebuilt using epoxy grout, tapered sole plates and a positioning jig."

Jan 1, 1988

By R. O. Burt, R. W. Bruce

"IntroductionGravity concentration, the separation of two or more minerals due to the difference in their relative specific gravity and usually in a fluid medium, is the oldest recorded form of mineral processing.The principles of gravity concentration were known to, and practiced by, the ancients and Hoover's commentary to De Re Meta/lied'' notes many early references.Over the centuries, as direct smelting ores became more and more uncommon, the mineral processing industry developed and along with it many varied methods of concentration. Gravity concentration declined rapidly in importance in the early twentieth century, and it is only in the last decade that its advantages are being re-evaluated.A significant proportion of ores are processed by gravity; a large proportion being in the iron and coal industries<'>, or in the treatment at very high volume of relatively coarse alluvial deposits. The tin dredges of South East Asia and Beach sand plants of Australia are prime examples.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive.Principle of Gravity ConcentrationGravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air.The relative movement of minerals to one another is achieved by a variety of methods. These are: separation in a fluid of intermediate density (heavy media separation); by stratification (such as in jigging); in a flowing fluid (cones, spirals, sluices etc.) and with a horizontal shear (shaking tables etc.)."

Jan 1, 1989

By A. Gutiérrez

At present, most ore milling is done in tumbling mills, consisting of huge cylinders turning on their horizontal axis. This rotational motion causes the ore charge and the grinding balls to interact by impact, compression and abrasion, to reduce the size of the ore. This method is very inefficient since only around 12% of the energy supplied is used for actual grinding, the rest being used in moving the large mass of balls and ore within the mill. This work aimed at better understanding the milling process by evaluating the movement of the load through the Discrete Elements Method (DEM). First, the number of bodies (balls and ore) moving inside the mill is determined, to correlate to the potential impacts that constitute one of the milling mechanisms. Then, the number of high energy impacts is evaluated to correlate to the bodies in motion. At this stage, a differentiation between grinding media and the ore, as well as between the types of contact taking place in the mill, has to be made. This latter issue is of great relevance since from the five identified contact types (ball-ball, ball-liner, ore-ore, ball-ore and ore-liner) only the last three actually contribute to the milling process, the other two causing structural damage to the mill.

Jan 1, 2007

By G. H. Faye

The prospect of obtaining high-grade concentrates from Canadian pyrochlore ores is rather unlikely, and experimental beneficiation pro-cesses ?appear to have yielded products in the range of 3 to 20 per cent N&apos;b205? A possible solution of the problem is to find an economical chemical method for recovering high-purity Nb2?05 from such concentrates. A technically feasible but economically unproved process is outlined in this paper, in which the concentrate is decomposed by an acid attack and the oxides of niobium and tantalum are isolated and then separated by liquid-liquid extraction. The solution of the ore is adjusted to 7 M HF-5 M HNO3 and the niobium and tantalum are extracted from this solution with methyl isobutyl ketone. The mixed oxides of niobium and tantalum are recovered from the oxdanic phase and dissolved in 0.5 M HF-1.0 M HNO3. Tantalum is extracted preferentially from this solution with methyl isobutyl ketone, leaving niobium in the aqueous phase. By the use of this process it is possible to produce niobium pentoxide and tantalum pentoxi.de in 99.5 per cent purity with a recovery of approximately 95 &apos;per cent, under lab-oratory conditions.

Jan 1, 1957

By William DeWit

When rivers are contaminated from industrial operations, as often occurs near repositories of spent mine tailings, decision-support tools can be critically important in evaluating the effectiveness of various engineering impact-management measures. Even where data describing river flows and quality are sparse, simple mixing-zone models can be constructed that can contribute greatly to understanding how impact-management measures can differentially affect existing river-chemistry regimes. There can be circumstances where accumulated surface waters near contaminated land can bear contaminant loadings that could be acceptable to river regimes if there were methods available to evaluate optional discharge rates and to predict post-mixing consequences on river chemistry. Nomographs can be constructed to evaluate discharge regimes that appear capable of releasing contaminated accumulated pond water without compromising water quality in a nearby river. River-mixing zone models also contribute to predicting rates of acceptable discharge and release to the receiving environment.

May 1, 2011

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By Yuhua Wang, Wei Sun, Dongfang Lu, Yuehua Hu, Tao Jiang

"With the continuous depletion of high-grade tungsten ores, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and use of toxic collectors.The aim of this study was to develop an environment-friendly processing flowsheet, which was used for beneficiation of low-grade tungsten ore containing 0.45% WO3 from New Brunswick in Canada, and the content of arsenic is 0.68% in this materials. The objective of beneficiation studied was to obtain a concentration containing 60% WO3 with less than 0.5% of arsenic under the condition without any flotation reagents. In this environment-friendly processing flowsheet, magnetic separation technology, classification and gravity separation technology were combined and employed. Firstly, magnetic separation was employed for the first pre-concentration process, over 95% of the feed was rejected as the final tailings, meanwhile, over 85% of arsenic minerals were removed with tailings. Secondly, gravity separation tests were employed on the classified magnetic pre-concentrate in the second pre-concentration process, a second pre-concentrate with WO3 grade of 54.32% and As grade of 5.41% was obtained. Finally, two stage magnetic cleaning were conducted on the second pre-concentrate for upgrading the second pre-concentrate, the mostly arsenic and gangues were removed from the second pre-concentrate. Finally, this novel processing achieved an effective recovery of fine wolframite from low grade tungsten ore with high arsenic. A concentrate with WO3 grade of 64.81% were obtained in new opened processing flowsheet, and As grade was less than of 0.5% in this concentrate. Furthermore, remarkable feature of this processing flowsheet is environment-friendly due to avoid using the toxic flotation reagents during the whole mineral processing.INTRODUCTIONTungsten is an essential metal and is the most widely used in industrial production such as national defense, electro-mechanical products, textile and leather sectors (Srivastava et al., 2000). Wolframite and scheelite are the main mineral sources of tungsten metal. With the continuous depletion of high-grade tungsten ores and the increasing demand for tungsten alloy, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and heavy use of toxic collectors."

Jan 1, 2016

By Virginia Lawson, Adam Price

The rougher flotation stage is used to reject liberated gangue at a coarse size. Base and precious metals due to their high specific gravity tend to recycle in the grinding circuit and report to the flotation circuit at a finer size than the gangue from which it is being separated. Generally liberation levels of greater than 50% are achieved in roughing and thus a portion of the feed can be immediately upgraded to final concentrate. The proportion increasing as the amount of liberated mineral in the feed increases. Scalping out concentrate from the rougher can reduce the size of the subsequent regrind and cleaner circuits. Examples of alternative process design for circuits demonstrates that you don’t need large volumes to effectively recover all of the minerals – you need smart flotation. Several case studies will be presented where circuits can be significantly reduced in size by designing smarter – not larger. This paper describes case studies to test the amenability of the Jameson Cell to produce final concentrate from rougher feed. Metallurgical performance and plant design implications are discussed. Froth flotation has been used extensively for mineral concentration for over 100 years. Although the flotation cell design has changed, it has generally simply increased in capacity rather than increase in efficiency. Cell capacities of over 600 m3 are now being used in rougher flotation particularly for the lower grade ores where the amount of surface area for flotation is deemed less significant than the required volume. The plant design volume in rougher flotation comes from laboratory batch flotation tests and/or pilot plants. The volume required for the plant is calculated based on the laboratory residence time multiplied by a scale- up factor. Examples of laboratory to plant scale-up design are given in Dunne et al. (2010 part 2). The factors are usually between 2 and 3. A laboratory residence time of 10 minutes would equate to a plant design residence time of 25 minutes using a 2.5 factor. The volume of the required flotation cells can then be calculated using the design tonnage and volumetric throughput. This scale-up factor takes into account the differences in performance between batch flotation efficiency and full scale plant. The differences are likely related to inefficiencies of bubble particle contact in large cells as well as froth recovery, which is essentially complete in a batch cell. Flotation cells, such as the Jameson Cells, are smarter designs that improve bubble/particle collection, bubble/pulp separation efficiency and operate with high froth recovery rather than simply getting bigger. The Jameson Cell was designed on the principal of improving the collection efficiency of fine particles by separating the contact zone from the separation zone and having the bubbles generated by the plunging jet shearing and entraining air. This means the method of bubble generation is not impacted by the wear of mechanical equipment as it the case in other flotation devices. Jameson Cells make bubbles less than 600 micron in size under most operating conditions (Ding, 2016).

Jan 1, 2019

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By C. Groccia

As the search for new ore bodies drives mines to be developed at greater depths, the associated high stress environments present challenges for rock support design. Excavations in highly stressed brittle rock are often subject to large volume increases due to rock failure, a phenomenon known as rock mass bulking, which can result in significant wall convergence. Support systems need to be designed to minimize the amount of bulking and to accommodate large wall convergences. In order to design such a support system, empirical guidelines are often used to predict the amount of bulking. However, the empirical guidelines that are currently available are based on a limited number of case studies and consider few input parameters, which may result in an inaccurate bulking assessment. This paper describes methods of collecting quantitative field data at Creighton mine in Canada to better understand rock mass bulking and to further develop the empirical guidelines for bulking assessment for tunnels in highly stressed grounds. Measuring

Aug 1, 2013

By R. R. Rogers

Introduction The subject of cathodic protection is not new. In 1824 Sir Humphry Davy, in publishing the results of his investigations for the British navy, pointed out that copper could be protected from sea-water corrosion by connecting it electrically with zinc or iron. Since that time much work has been clone in this field, particularly in the protection of metals from the action of sea water, neutral brines, and treated and untreated waters. Special mention should be made of the successful protection of underground pipe-lines which formerly were badly corroded by the water in the ground. So far, magnesium alloy and zinc anodes have been the most popular. However, fairly recent work has indicated that aluminium anodes will give good service under certain conditions. The principle of cathodic protection has been applied extensively in coating steel articles with zinc and in cladding aluminium alloy sheet with pure aluminium. A valuable discussion of the fundamentals and applications of cathodic protection recently was presented in the Corrosion Handbook. A useful list of references was included in the article.

Jan 1, 1949

By C. Chapman, P. Cowx

"INTRODUCTIONTetronics Research and Development Co. Limited has installed several plasma torches for steel heating in continuous caster tundishes. An extensive demonstration program on a 14 tonne tundish reported the following advantages of plasma heating.• close control of steel temperature to ± 5°C;• a reduction of the furnace tapping temperature of up to 20ºC, leading to savings in energy and refractories costs ;• improvement in steel quality, to produce a slab product with an equi-axed crystal structure and a reduced number of large sub-surface slag inclusions;• the virtual elimination of oxygen pickup in the tundish; and• the capability of making ferroalloy trim additions to the tundish to permit a change of steel grade during casting, greatly decreasing inventory costs.The Need for Tundish HeatingIn the continuous casting of steel, the function of the tundish is to transfer the molten metal between the ladle to one or more continuously fed casting moulds. Figure I shows a typical temperature profile of molten steel in the tundish over the first cast cycle. It is observed that a rapid drop in temperature occurs both at the start of the cast, due to the tundish refractories absorbing heat, and also during ladle changeover. In addition, as a result of thermal losses through the ladle sidewalls, there is a gradual decline in the bulk steel temperature over the entire heat cycle. Consequently, in normal tundish operation, it is necessary to cast with a high superheat (25°C to 30°C + above steel liquidus temperature) in order to prevent freeze-up of the strand. Problems of high temperature variation and the potential of the steel solidifying in the tundish are greater for small caster units of low thermal mass . A high steel superheat increases the steelmaking vessel process time and refractory wear and prevents the formation of a uniform equi-axed solidification structure in the cast steel, resulting in centre line segregation and porosity. The large drop in the casting temperature that occurs during unsteady state operation causes an increase in the number of sub-surface inclusions, reducing the value of the product. Accordingly, plasma heating may be employed to maintain the molten steel at an optimum temperature to produce a slab of consistent quality."

Jan 1, 1989

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

By M. Leroux, C. J. Martin, S. R. Rao, J. A. Finch

"The effect of nitrogen on the flotation separation of sulphides from complex ores from Brunswick Mining and Smelting (New Brunswick) and Mattabi Mines (Ontario) was investigated. The most significant finding was enhanced pyrite floatability after as little as 3 minutes nitrogen conditioning. This was used in a novel sphalerite/pyrite separation process developed on the Brunswick ore. After aeration and Cu/Pb bulk flotation in air using xanthate the slurry was nitrogen conditioned, xanthate added and the pyrite floated in nitrogen. As an example up to 70% pyrite recovery with about 20% sphalerite recovery was achieved. Sphalerite was recovered from the pyrite tailings and the pyrite concentrate by copper-activation, raising the pH to 10 and floating in air. About 65-70% recovery at 35-40% Zn grade was achieved compared to 25% Zn grade by the conventional route. The process offers a promising alternative to current practice which seeks to depress pyrite at all stages. A possible mechanism of the effect of nitrogen is presented. INTRODUCTIONUse of gases other than air in froth flotation has been reported from time to time. [Podobnik and Shirley, 1982; Lin and Metzer, 1975]. Of all the gases, nitrogen would appear to hold the greatest practical promise because of its easy availability and chemical inertness. It is used in froth flotation in chalcopyrite-molybdenite separation [Redfearn, 1983]. The use of nitrogen in polysulphide chalcopyrite. this case is mainly to reduce the oxidation of a compound (Nokes reagent) used as a depressant for There is no reported use of nitrogen in the flotation of other sulphide minerals."

Jan 1, 1988

By Sadan Kelebek, Gerhard W. Heinrich, Peter F. Wells, Peter J. Whittaker

"Based on plant mineralogical data & circuit modelling, a pilot plant campaign was conducted at Strathcona Mill to identify options for improving the performance and operating flexibility of the copper-nickel separation circuits. Emphasis was given to options for combined treatment of the two feed streams (primary nickel ore rougher concentrate and copper ore circuit concentrate) to obtain more flexibility in the use of existing column flotation capacities. The pilot test results demonstrated that circuits which incorporated preconcentration prior to column flotation gave the best metallurgical results. Maximum column carrying rates were also related to the preconcentration. Predictions that increased circulating loads from the column scavengers would improve copper-nickel separation performance were confirmed.IntroductionThe copper-nickel separation circuits at Falconbridge's Strathcona Mill produce a high grade (>30% Cu) copper concentrate most of which is treated at the Falconbridge Kidd Creek smelter near Timmins. The remaining nickel concentrate which still contains approximately 20% of the feed copper is combined with other lower grade nickel/copper concentrates and shipped to the Falconbridge nickel smelter. The separation is required because of the limited capacity for copper processing in and downstream from the nickel smelter. Since no nickel is recovered at present in the Kidd smelter, the challenge is to minimize the nickel content of the copper concentrate.At present there are two independent separation circuits treating the rougher concentrates from the copper and nickel circuits as shown in Figure I. The minerals treated are mainly chalcopyrite and pentlandite but there is up to 25% of the copper present as cubanite in the copper ore. The circuits were kept separate because the flotation rates and froth characteristics were very different, probably because of the presence of cubanite and the large difference in the concentrate grades feeding the circuits."

Jan 1, 1995

By Mohammadreza Jalali

Alberta contains over 400 billion barrels of viscous crude oil in fractured carbonates but there is no viable extraction technology as yet. Petroleum geomechanics has become a vital part of the assessment of such hydrocarbon reserves, especially for naturally fractured cases, which are particularly challenging in terms of accurate recovery prediction because of joint fabric complexity and lithological heterogeneity. As a result of interconnected fractures, transport properties of fractures (mostly permeability issues rather than thermal effects) are affected by production and injection activities that change the pore pressures, temperatures, saturations, and effective stresses. Enhanced oil recovery methods involving massive amounts of fluid injection (hot or cold) at high pressure (pinj) may be used to mobilize and produce the oil; therefore, deeper understanding of the fractured systems is desirable. Pressure and temperature variations in a fractured reservoir change the in situ stresses in the reservoir and surrounding rocks; this affects fracture apertures, radically changing the bulk flow properties because flux rate is highly sensitive to aperture. Hence, coupled pressure, temperature and effective stress changes must be considered for fractured reservoirs under a thermo-hydro-mechanical (THM) coupling approach.A hybrid FDM/DDM coupled method is presented to couple pore pressure and stress around a fracture in an impermeable matrix block. Deformation and stresses are calculated in each time step and then fracture permeability, which is the most sensitive petrophysical parameter in fractured reservoirs, is updated based on the fracture aperture variation. This model is then verified with UDEC (Universal Distinct Element Code) which uses a discrete approach to cope with fractured rock mass behavior.

Jun 1, 2012