Search Documents

By M. Silva, G. Olivares

In a leach pile, the drainage layer or commonly known as the cover layer has been a matter of discussion due to the multiple phenomena or events that occur within it which impacts negatively the leaching process. All these events are directly related to the loss of draining capacity and irregular flow net due to an excessive compaction and entrapment of fines reducing the flow velocity which in turn cause more fines to get trapped. Over time the problem will continue to worsen rapidly and accelerating continuously like a geometric progression. When the cover layer gets to a certain level of deterioration, the only alternative to continue operating safely is to replace the entire cover material, a huge cost for any mining operation. TESRA has developed a solution to counteract the accelerated advance of the deterioration of the drainage layer. The solution consists of using large agricultural tractors coupled to a proprietary design of a heavy- duty subsoiler-ripper for deep tillage for loosening and breaking up the ground at various depth and with different legs spacing from 0.4 m or above. Also, if the ground still requires additional breaking, TESRA proposes the use of a rototiller that breaks any lumps to homogenize the ground to a certain particle size. With the subsoiler-ripper/rototiller combination equipment a layer of 0.5 m deep is properly treated to match closely the original conditions of the ground thus regaining the flow net as close as to the original seepage condition. Once the ripping is completed the subsoiler-ripper tool is replaced with another that is similar to a plow and thus continue with the installation of drainage pipes. The tool digs a Y-type profile trench allowing the pipe to sit precisely at the bottom of the trench, contributing additional lateral and lower support. This tool controls the installation depth of the drainage pipe at different inclination grades and also eliminating any irregularities that may block the flow of the leaching solution. Sometimes the obstructions block completely the flow of the solution. The main result of this methodology is the reduction of groundwater levels and at least 2% less humidity in the leaching gravel due to an increase in the draining capacity of cover. The methodology developed by TESRA applied during a couple of cycles of a dynamic leach pile has proven to be a real alternative to remedy and recuperate the cover close to its original conditions. The methodology requires only one large tractor and two accessories operated in different stages while replacing the more traditional and less efficient machinery such as the Bulldozer, Motor-grader, and backhoes.

Jan 1, 2019

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

?Introduction to the Delphi Group ?Why is carbon important to your organization ?Key elements of a carbon management strategy ?Inventory ?Risk & opportunity scan ?Mitigation options and financial mechanisms ?Identify targets and develop policy ?Communication and improvement ?Manage for success

May 1, 2009

By G. Vibert Douglas

Introduction A preliminary paper dealing with the subject of ore-shoots was presented to this Society at its Annual Meeting last year (1). The present paper records the attempts which have been made during the interval to further this study. In reporting this work, I wish to state that I do not consider the investigation complete; many more experiments will have to be carried out, and more field data will have to be recorded, before the geologist can say with confidence an ore-shoot should start at this point and pitch in that direction. The aim of these experiments is to find some criteria which will serve the mining engineer and mining geologist concerned with ore-shoots in hydrothermal veins.

Jan 1, 1935

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006

By X. F. Liu, O. Buzzi, Y. Sieffert

This study falls in the context of underground coal fires (UCF) where burning coal can elevate the temperature of a rock mass in excess of thousand degrees. The objective of the research was to experimentally investigate the change in mechanical behavior of a rock when subjected to temperatures up to 900 °C. Several blocks of an Australian mudstone were collected from a mining site in New South Wales, Australia. X-ray diffraction and thermal-gravimetric analysis were conducted on powdered rock in order to determine the critical temperatures at which the main mineralogical changes occur. Then, cylindrical specimens were prepared from intact rock blocks for unconfined compression tests. These rock specimens were then treated by heating in a temperature-controlled furnace at temperatures varying from 100 °C to 900 °C. The heating process consisted of two stages: raising temperature with very slow rate of 1 °C per hour followed by a holding period of 24 hours and then a slow cooling process to room temperature. The compression tests were carried out on treated rock specimens to characterize the change in compressive strength. The macroscopical study was complemented by microstructural investigations via optical microscope, scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). Results show that the unconfined compressive strength of mudstone decreases with increasing heating temperature up to 450 °C, beyond which it increases. This can be explained by the combined effects of micro cracks and mineral thermal reactions caused by heating process.

Jan 1, 2015

By R. D. Brown

Higher metal prices have resulted not only in increased exploration and production, but also increased activity in the purchase of mining properties and mines. This article discusses some of the basic income tax considerations to be taken into account on the disposal of an interest in a mining claim or an active mining operation. It notes the importance ofan appropriate allocation of the purchase price amongst the various categories of assets, and discusses the tax implications to both vendor and purchaser of the transfer of the comm on types ofassets involved in mining operations. In the space available, the article can only outline the basic tax considerations, and point to areas where both vendor and purchaser need to be o

Jan 1, 1980

By M. Takebayashi, M. Shingu, H. Nagai, T. Nakai, S. Asano

The Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. (SMM) is located in the coastal zone of Saijo City and Niihama City, Ehime Prefecture, Japan. The refinery has been producing copper, sulfuric acid, and precious metals such as gold, silver, and PGMs. Previously, the process of precious metals recovery was a combination of pyrometallurgy and an electro-refining process with the conventional cupellation for around 400 years. However, this process had some major problems such as non-efficient recovery of valuable metals, high environmental risk by pyrometallurgy, high cost for maintenance of equipment and so on. In order to solve these problems, a thorough hydrometallurgical process for precious metals refining using chlorine leaching technology was originated and developed by Sumitomo and thereafter commercialized in 2004 at Toyo Copper Smelter and Refinery. This new process enabled shorter-term recovery of gold and manpower saving, and occupational safety and working conditions have also been improved. Superiority over the existing hydrometallurgical processes was also confirmed, for example by the achievement of 99.99% pure silver production without an electro-refining process. This paper summarizes the hydrometallurgical technologies for precious metals recovery such as chlorine leaching of copper anode slime for silver recovery, solvent extraction (SX) for gold recovery, and ion exchange (IX) for PGMs recovery. It also presents a unique silver purification process. INTRODUCTION Sumitomo Metal Mining Co., Ltd. (SMM) produces copper, precious metals and rare metals as by-products at the Toyo Copper Smelter and Refinery, and nickel and cobalt at the Niihama Nickel Refinery. Precious metals contained in nickel ore are also separated and refined at the Toyo Refinery after concentration. SMM has been refining precious metals using the pyrometallurgical method. In recent years, we have revamped the separation and refining process of precious metals dramatically by making use of advanced hydrometallurgical and engineering technology developed in the company. In this paper, we introduce the history of development and techniques of this process, and also introduce in detail the technologies of gold refining, PGMs recovery, selenium recovery, and silver refining which have been particularly difficult to achieve.

Jan 1, 2019

By A. Noël, R. Lapierre, M. Provencher

"Modem aluminum smelters are facing significant operating cost pressure. Key methods used by smelters to manage this pressure are automation and production-information systems to optimize processes, manage quality, anticipate problems and reduce operating costs. In 2002, Aluminerie Alouette Inc. began its Phase II Expansion project, and retained the joint venture of SNC-Lavalin and Hatch (SLH) as its engineering, procurement and construction management (EPCM) team. Alouette had the distinction of being one of the most efficient aluminum smelters in the world. Alouette already understood the importance of systems integration in project delivery. For Phase II, key objectives were identified to ensure ""a state of the art"" integrated architecture that would support Alouette's production goals to integrate the existing facilities with the expansion, to form a single efficient facility and meet project schedule and budget targets. Achieving those objectives within the context of a large project often creates major challenges due to the nature of the traditional EPCM delivery model, which relies on several vendors and third-party-systems integrators. In this case, an integrated Alouette-SLH team was made responsible for all aspects of the systems integration, taking over the task from most suppliers. The integrated team was responsible for delivering an automation system and plant-wide-production IT system for the new facilities while accommodating migration for the existing systems. Through the use of rigorous methodology and advanced state of the art technology, the IT and automation strategy led to significant value creation and is recognized today as one of the key factors of the project's success. The primary results were: fast and efficient start-up of facilities, due to quality programming and implementation; a plant able to operate as a single entity; automation and IT systems delivered before time and under budget; standard programming methods implemented throughout the plant; and reduced and simplified maintenance."

Jan 1, 2006

By W. E. Bawden

Situation: Creighton mine, situated about twelve miles west of Sudbury, Ont., on the Algoma Eastern railway, is owned and operated by the International Nickel Company, incorporated in the United States under the laws of New Jersey. The ore is smelted at Copper Cliff, near Sudbury, and the matte is refined at Port Colborne, Ont., on lake Erie. Geology: The ore occurs in what is known locally as 'the basin' near Sudbury (Figure 1) the central part of which is composed of the Animikie series of sediments, consisting of sandstones, slates, tuffs and conglomerates. The basin is about 16 miles wide and 36 miles long. The Animikie sediments are surrounded by a sill of norite - a gabbro rock in which the pyroxenes are orthorombic. On the outer contact of this norite the sulphide deposits occur and the Creighton deposit, similar to others, lies on the southern edge of this basin. There are two orebodies at the Creighton, the upper one called the footwall orebôdy, and the lower one the hanging-wall orebody. The hanging-wall of both of these bodies is norite, and the footwall of the upper one is granite. The two are separated by an intrusion of greenstone which forms the footwall of the lower body. The ? maximum length of the deposit is 1000 feet and the maximum width is approximately 300 feet. It narrows at the ends and is somewhat lenticular in shape. The dip is about 45 o to the west, and the strike is north and south. The orè is a mixture of three minerals - pyrrhotite, chalcopyrite and pentlandite. The pentlandite, which is distinguished by its cleavage from the other two, is apparent to the naked eye only in the lower orebody and is more finely disseminated in the upper one. The lower body contains a little higher percentage of nickel.

Jan 1, 1925

By H. Weissenbaeck, B. Nowak, M. Oesterreicher, R. Stastny

The producers of certain metals like nickel and cobalt increasingly face a shortage of easy-to-mine and easy-to-process ore bodies. Their focus is shifting towards alternative raw materials which in turn demand new, different extraction techniques. One potential route for processing a ferrous ore with a non-ferrous target metal is atmospheric leaching with hydrochloric acid followed by purification of the pregnant leach solution (PLS). For the separation of iron from the PLS, and, in turn, the extraction of the non-ferrous compounds, the following flow sheet is proposed. Pre-concentration of the PLS, oxidation of ferrous (if present) to ferric chloride, hydrolysis of ferric chloride leading to the precipitation of hematite and the evaporation of hydrochloric acid, followed by crystallization of non-hydrolysable metal chlorides by means of sparging hydrogen chloride into the solution. Hydrogen chloride required in the latter step is produced internally by super-azeotropic distillation of regenerated hydrochloric acid. The liquid filtrate from the crystallization step is recycled to hydrolysis. Depending on the specific composition of the PLS, the hematite produced contains only traces of other impurities, whereas the crystallized mix of non-hydrolysable metal chlorides – containing also the target metal in enriched form – contains ferric chloride only in an amount referring to the filter cake moisture. These crystals can then undergo further hydrometallurgical separation and extraction processes. As an example, this flow sheet is proposed for treating nickel laterite ores. Experiments related to the demonstration of crucial assumptions in the flow sheet are presented. Based on those experiments a mass and energy balance of the flow sheet was calculated and is presented here together with a table of the major consumables in order to provide a basis for an operating cost estimate and other process economics.

Jan 1, 2016

By O. S. Perry, D. F. Kidd

"BEAVERDELL IS IN the Interior Plateau of British Columbia, 25 miles east of Penticton, B.C. In 1897, small but rich silver-bearing veins were found on Wallace Mountain, 2 miles east of Beaverdell. Production from the camp, at first of a modest character, started in 1901 and has never ceased. Over 90 per cent of the values in the ores have been in silver. Remaining values present are in lead, gold, zinc, and cadmium.There have been four principal mines in the camp. A fifth is approaching production. The four mines lie within a northeasterly trending rectangle about 5,000 feet long and 2,000 feet wide, the fifth mine being at the northeast end. From southwest to northeast the mines, with their silver production to Sept. 30, l 955, are: -Wellington Mine - 1,463,948 oz.Sally Mine (includes Rob Roy claim) - 1,930,124 oz.Bell Mine - 3,460,815 oz.Lass Mine - 12,557,956 oz.Other production - 331,252 oz.Total, Beaverdell Camp - 19,744,095 oz.The camp is near the centre of an area geologically mapped in 19 l l by L. Reinecke for the Geological Survey of Canada (1). The rocks of the camp comprise:1. Beaverdell stock of porphyritic quartz monzonite;2. Westkettle batholith of quartz diorite;3. Wallace formation of tuffs and lavas.The Wallace formation borders the east edge of the camp, and has been intruded by the Westkettle batholith. The batholith is the host rock for the orebodies. The Wallace-batholith contact dips gently east. Some of the Beaverdell ores at depth, while in the batholith, are under Wallace formation mapped on the surface above.West of the camp, Reinecke mapped a stock one by one and one-half miles in size, of porphyritic quartz monzonite, which he considered much younger than the Westkettle quartz diorite (I). Recent petrographic work by White and Dolar-Mantuani (3) suggests that in the vicinity of the camp the Westkettle batholith is more quartz monzonite than quartz diorite, and little different in composition from the Beaverdell quartz monzonite. They suggest a consanguinity with the Westkettle batholith."

Jan 1, 1949

"Eastern Canadian thermal coal mined at Minto, New Brunswick, and in western Cape Breton at St. Rose, Inverness County, Nova Scotia, contains 6-8 per cent sulphur. Both coals are high volatile bituminous. types. The Minto coal averages 18 per cent ash, 7 per cent sulphur and has a Btu rating of 11,900 per lb. Pyritic sulphur accounts for 75 per cent of the total sulphur and the remainder is largely organic; the amount of sulphate sulphur is negligible. This means that in a 7 per cent sulphur coal, 2 per cent is organic and 5 per cent pyritic sulphur. Pit-head St. Rose coal contains approximately 10 per cent ash, 7 per cent sulphur and 11 ,800 Btu/lb. The distribution of sulphur is different to that of Minto coal because about 12 per cent sulphate sulphur is present. Thus, a 7 per cent sulphur coal would contain 4 per cent pyritic, 2 per cent organic and 1 per cent sulphate sulphur.The iron sulphides, pyrite and, to a lesser extent, marcassite occur over a wide size range from large sulphur balls to crack fillings, lenses, and individual crystals and framboids. Coarse-grained pyrite and sulphur balls are easily separated during washing. It is the fine grain sizes, intimately mixed with the coal constituents, that are difficult to separate. Quantimet analyses of the fine grains in coal from both localities showed that about 50 per cent were smaller than 30 micron(1).No efforts have been made to wash the Inverness coal of Nova Scotia and in 1980 washing ceased in New Brunswick. Previously, the Minto coal was processed in an antiquated jig circuit which reduced ash from the strip operation run-of-mine value of more than 20 per cent to less than 18. More effective removal of ash and sulphur could clearly be obtained. Laboratory tests on both Minto and St. Rose coal have shown that ash rejection rates of 40 to 50 per cent at yields of 70-80 per cent were possible(2), Little information on sulphur removal was available."

Jan 1, 1981

By L. Fernandes

A factorial study was performed to investigate the relative effects of temperature, copper concentration and meso-2,3-dimercaptosuccinic acid (DMSA) concentration on the performance of thiosulfate leaching of gold. A total of 24 leaching experiments were performed representing eight unique combinations of high-low levels of the three factors performed in triplicate. All investigations were performed in an electrochemical cell with an electrolyte composed of 0.1 M sodium thiosulfate with a combination of copper (either 0 mM or 1 mM) and DMSA (either 0???or 1µM). All leaching investigations were conducted under open circuit while the electrolyte, which was open to the atmosphere and mechanically stirred, was maintained at either 25°C or 50°C. After 1.5h of leaching the amount of gold in solution was quantified using ICP-MS analysis from an aliquot of the electrolyte. Results indicate that DMSA addition improved gold leaching performance, most notably at 50°C and with addition of copper. Under this unique condition, the quantity of gold in solution was reproducibly and significantly above the average response of all other factors studied.

Jan 1, 2014

By D. Murray

A 2-hectare uranium tailings area has been reclaimed. The exposed tailings of 1.4 hectares were capped with glacial till and vegetated with grasses and legumes. The water running through the tailings was diverted around the tailings in a line ditch and treated with sodium hydroxide and barium chloride. Difficulties occurred in placing the till capping because of the low bearing strength and the uneven surface of the tailings. This led to varying thicknesses of till and the need for manual labour in some areas. Total reclamation costs were $32,200, with vegetation establishment costs at $13,700 per hectare. This report provides a record of work for use in assessing the long-term suitability of these treatments.

Jan 1, 1979

By J. E. Dutrizac, J. B. Sunstrum

"Lead was among the first metals known to man, and there are indications that lead was produced by the reductive smelting of galena in the mountains surrounding the Black Sea as early as 3000 B. C .(1). The early metallurgists soon discovered that silver could be recovered from lead bullion by cupellation techniques, and that the litharge product of the cupellation process could be reduced to give silver-free lead metal. By the Graeco-Roman era, lead-silver ores were being extensively exploited for both their silver and lead contents. Although silver was always of prime concern, a number of industrial uses existed for lead that included piping and sheeting. Subsequently, lead metallurgical practice developed steadily in different parts of the world, and was a relatively mature technology by the time of the European colonization of North America. In the United States, lead was produced on a small scale as early as 1720, and by 1800, the extensive Pb-Zn deposits of Missouri-Kansas and the upper Mississippi Valley were being developed(2). Many of the early American lead ores were low in silver, and seemed to have been worked primarily for their lead contents. Major uses of lead at the time included bullets, pipe and sheeting. During the period 1860-1890, the silver-rich galena ores of the western United States were exploited, and a number of lead smelters were operated. Although all the smelters produced lead metal, the recuperation of the associated silver and gold values was generally of prime concern. In Canada, lead deposits are abundant, and galenarich outcrops frequently attracted the attention of the early explorers and prospectors. In fact, the first record of a Canadian ore deposit seems to have been the observation of an argentiferous galena vein near Lake Temiscamingue in 17 41(3). The presence of silver-bearing lead deposits naturally attracted the attention of the mining community, and many outcrops were worked throughout the country. Because of the problems associated with transporting lead concentrates to existing American or overseas smelters, attention soon shifted to the establishment of local lead smelting facilities. The purpose of this article is to examine those early smelting efforts and to try to identify the first ""successful"" Canadian lead smelter."

Jan 1, 1999

By A. J. Harrison

"The introduction of an amendment to the Mines Regulation Act in the Province of British Columbia, passed in July 1974, and similar amendments since enacted by other provinces introduced the Canadian underground mining industry to the use of fire-resistant hydraulic fluids.Few, if any, of the hydraulic circuits in use in underground mining at that time were specifically designed for use with fire-resistant fluids, compared with the increasing number of such circuits conceived and in production today. The technology required in designing equipment for use with fire-resistant fluids may be likened to that associated with conventional mineral oils, but, in many respects, a variety of additional and / or alternative considerations must be taken into account. The fast-increasing use and development of fire-resistant fluids throughout all facets of industry, world wide, during the past 20 years has led to a whole new technology in system construction and component design, whereby acceptable performance can be achieved . However , the transition from conventional mineral hydraulic oils has not been without its problems, particularly when retro-fit of existing units was involved."

Jan 1, 1981

By T. Kawai

Japan Oil, Gas and Metals National Corporation (JOGMEC) has started an exploration program for Seafloor Massive Sulfides (SMS) in the EEZ of Japan, and launched an investigation program for mining, processing and environmental impact on SMS development. With regard to the mining aspect, the mining system consists of three units: a mining unit on the sea floor, an ore lift-up unit to surface, and a mining support vessel unit which has an ore unloading system that unloads onto a shuttle ship. Regarding the mining unit, JOGMEC and certain Japanese mining and machinery companies developed two types of state of the art mining testing tools. Excavation tests on the actual SMS site in the Okinawa Trough, south-west of Japan, were conducted in 2012. In these tests, the functions of the testing tools, such as cutting ore, moving on the seafloor and climbing up slopes having steeper than a 25 degree gradient, were confirmed. The physical characteristics of the ore, which are key parameters for establishing a mining system, are yet to be fully understood as the exploration program has been undertaken simultaneously. Hence, those examinations have been carried out by ground cutting experiments, analysis of drilling core data, and the like. This paper describes the outline of a proposed mining system, mining testing tools and results of the on-site mining testing.

Aug 1, 2013

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By Bruce J. Barker

"Environmental concerns have recently been growing over the disposal of reactive desulphurizing slag. Consequently, increased pressure has been placed on the foundry industry to reduce the reactivity of this slag.To address this problem, Cyanamid has developed a new product which significantly reduces the calcium carbide content of the desulphurizing slag. Testing equipment and procedures have also been developed to evaluate both the existing levels of carbide in the slag and the decreased levels which are achieved with this new material.The development and use of this engineered carbide desulphurizer has made possible significant environmental and efficiency improvements in the field of calcium carbide desulphurizing. Consequently, the lifespan of calcium carbide in ductile iron desulphurization has been increased, as have the benefits of its use in the foundry industry. IntroductionIn the production of ductile iron, calcium carbide has long been used for hot metal desulphurization external to the cupola. Its cost effectiveness, reliability and ease of use have traditionally made it the desulphurizer of choice for a great majority of ductile operations. Recently however, environmental concerns have been raised regarding the quantity of calcium carbide remaining in the slag after desulphurizing. Analysis has shown that as much as 25070 of the weight of the slag may contain active carbide. This has caused disposal concerns as calcium carbide when in contact with water, produces acetylene via the following reactionr:"

Jan 1, 1992