Search Documents

By A. B. Szwilski

"The various elements of longwall mine design are reviewed, particularly as they apply to condition s in the coalfields of the Plains region of Alberta. The following recommendations are made: (1) optimum panel lengths of 1000 to 2000 metres; (2) face lengths of 100 to 150 metres; (3) the use of retreat methods; (4) the restriction of floor undulations to less than 15 degrees. IntroductionThis article considers the elements of longwall mine design and is part of a short study that has been made of the feasibility of longwall mining in the Plains region, Alberta, Canada. The Plains region, with about 20 million tonnes, accounts for more than 80% of the coal resources of Alberta. The coalbearing strata in the Plains region cover an area of about 95,000 square miles. The geological formations dip very gently toward the southwest and, from a mining point of view, may be considered horizontal. The depth of the coal seams varies from several metres to over 650 metres. However, it is not anticipated that underground mining will be extended beyond the depth range of 25 to 250 metre s.The coal seams in the Plains region have been subject to many small mining operations in the past. The majority of these small mines were limited to a depth of about 50 metres, working mainly by room-and-pillar methods, although hand-filled longwall mining was often used.The development of new underground mining operations in the Plains region will have to be on a 'start-from-scratch' basis, especially regarding the installation of equipment. Longwall mining is more mechanized than any other method of mining and requires careful attention for the selection of new and expensive equipment. There have been many proven longwall advance and retreat systems in Europe and North America; mining conditions in the Plains region are more similar to those in the United States. Therefore, it will be essential for new mining pro jects in the Plains region to commence with proven system s and equipment; in time, perhaps an experimentation process could be attempted as experience is gained.Generally, the coal face is the key factor in mine productivity, which depends a great deal on equipment reliability, training and experience of the operators. The original design of coal faces must be flexible enough to cater for potential improvements so that running time can be increased."

Jan 1, 1980

By W. N. Roman

This paper will examine the challenges involved in ventilating and cooling South African mines, with particular emphasis on solutions to the issues of heat (generally associated with depth), mechanization and energy efficiency. Comparisons will be made with other international mining areas. Some of the deepest mines in the world are to be found in the South African goldfields. The Mponeng mine is approaching 4,000 m below surface, with virgin rock temperatures (VRT) of between 60°C and 70°C. Mining at these depths has only been possible with the use of large refrigeration plants supplying cold air, water and ice to the workings. In the Bushveld Igneous Complex, where most of South Africa?s platinum mines are located, similar VRTs are being experienced at significantly shallower depths. This is due to the different geothermal properties of the host rock between the two areas. Existing mines are being forced to go deeper and new underground mines are being planned and constructed in other areas with widely differing thermal conditions. South African metal mining has traditionally been labour intensive for historical reasons as well as for the narrow tabular nature of many ore bodies. Due to cost pressures and labour problems, some mines have been investigating the possibility of using mechanized equipment, both diesel and electric, to increase production and to improve efficiency. Studies have been carried out to determine the effect of the additional equipment on the overall ventilation system and some of the conclusions are discussed. The use of diesel equipment adds heat and pollutants to the ventilation air but, although electrical equipment has a lesser effect on the ventilation systems, it is generally less favoured due to claims of lower flexibility/manoeuvrability. Mechanization holds the promise of more concentrated mining activities but, with higher localized ventilation and cooling needs. Systems which will control the provision of air and cooling more effectively are required and are being implemented. In the 1990s and early 2000s, the South African economy experienced significant growth which was not matched by the growth in infrastructure. Consequently, at present there is a shortage of electricity generation capacity which affects large industrial consumers, including mines. Increasing levels of heat and mechanization will require more electrical energy for ventilation and cooling. There are many initiatives underway to save power or to shift consumption to periods of national low demand and these will be described.

Aug 1, 2013

By G. R. Heffernan

"In the early 1970ssteelmakers worldwide were looking forward to many years of expansion and profitability. Huge government investments in Europe, the United Kingdom, Japan, Brazil, and Venezuela were committed in anticipation of growing market s based on long-term OECD forecasts. In 1973 the first OPEC oil shock occurred. Steel demand shrank. Restructuring became the buzz word of the day as billions of dollars in taxpayers' money was poured into eliminating excess capacity and labour. In the United States, where government help was not available, inefficient companies went bankrupt; capacity was cut to 100 million tons from 155 million tons. The industry throughout the industrialized world shrank. By 1979the world economy seemed back on track and a modest degree of optimism could be detected in the international steel fraternity. Then came the second oil shock. By 1982 the industry was in the midst of another shakeout. More bankruptcies, more rationalization, and fewer jobs resulted. In Canada some well-known companies came close to the brink as low prices and high interest rates took their toll. In the light of the turmoil in the steel market over the past 20 years an attempt to forecast the trends through to 2001 is intimidating.However, there are good reasons to be optimistic today about both markets and technology.An economic super power is emerging in western Europe as 1992 draws near. The creation of a single market of 320 million well educated and economically ambitious people has major positive implications for steel demand. The mega projects of the channel tunnel, a European network of high speed railways, and the London docklands are the forerunners of greater things. Still to come is another $200 to $300 billion by the year 2001 in identifiable major projects for highways, railways, airports, water and sewage systems. Add to that the demands of an increasingly affluent population for automobiles, appliances and housing. On top of all that place large increasing demands for electric power and you have a potential beyond anything seen during the 1970s and 1980s. In 1988 the EEC steel industry operated at 90% and in 1989 at 92% of effective capacity. A surge in spot prices indicated that 92% was close to the ceiling. This pace moderated in early 1990 but any slack will probably be taken up rather quickly."

Jan 1, 1990

By Esa Peuraniemi, Hanna-Leena Heikkilä

Boliden Harjavalta has been operating a copper flash smelter since 1949. Thus, in 2019, the smelter is celebrating its 70th anniversary of flash smelting. Slag formation is an integral part of the smelting process; currently the processing of slag is based on froth flotation at the slag concentrator. It provides high recovery of copper but restricts slag utilization; the final copper slag is deposited in a landfill. The Harjavalta smelter commissioned a new landfill area for final slag in May 2018. This paper describes the full project from permitting to commissioning of a new landfill area. The permitting process is described comprehensively, including environmental impact assessment together with the environmental and dam safety monitoring. During the environmental impact assessment, observations on rare animals protected on European level were made as well as archaeological findings. Successful completion of the permitting allowed the construction phase to start on time. After six years of intensive work, the new landfill was commissioned in May 2018. The new landfill area provides a sustainable way to store the smelter’s slag for decades to come. INTRODUCTION Slag processing Sulphide based concentrates have always formed the main raw material stream at Harjavalta’s copper smelter. During the smelting and converting steps, the iron included in the concentrate is oxidized and fluxed using a silica-based sand. Originally, the slag was processed by using an electric slag cleaning furnace after which the final slag was water granulated. Froth flotation has been utilized for slag treatment since 1966. In the beginning, the slag was cooled in open ditches. In 1984, controlled slow cooling of slag was licenced to enhance copper recovery at the flotation plant. Today, the slag from both the smelting and converting is tapped/skimmed to slag ladles and treated in the following steps: Slag ladle transportation from the smelter to the cooling area by slag hauler Slow cooling of slag in the ladle to allow mineral precipitation Unloading the slag by tilting the ladle; causing the slag to crush as it drops from the ladle Feeding the crushed slag (-500 mm) by wheel loader to a slag concentrator’s feed funnel followed by a conveyor belt transporting the slag to the concentrator plant Crushing and grinding using lump and pebble mills Froth flotation of the valuables Recycling the slag concentrate back to the smelter feed after dewatering Pumping the final copper slag to the landfill area.

Jan 1, 2019

By W. R. Richmond, T. S. Li, D. Ilievski

The reactive precipitation of ferrihydrite was studied in a laboratory semi-batch precipitator, where a highly concentrated sodium hydroxide solution was fed into an iron nitrate solution. Instantaneous hydrolysis of iron[III] takes place when the two reagents are mixed generating supersaturation, and leading to immediate precipitation of ferrihydrite via a primary nucleation mechanism then followed by limited crystallite growth to 3 to 7nm. A mathematical model of the semi-batch laboratory precipitator was used to simulate the pH responses during the precipitation of ferrihydrite at different reagent feed rates. The model comprised of interconnected compartments of averaged hydrodynamic conditions, incorporating physically meaningful turbulent mixing time constants. The precipitation process is described by the solute concentration conservation equation incorporating a postulated ferrihydrite primary nucleation model. It was found that the semi-batch precipitator model predicted the experimental pH response reasonably well. The experimental results demonstrated that the reagent feed rate has a critical effect on the course of the precipitation of ferrihydrite, i.e. it is a rate determining step given the fast hydrolysis and precipitation kinetics.

Jan 1, 2005

By T. Patching

"COAL MINING at Canmore, Alberta, began in 1886 and continued there until July 1979. A comprehensive review of the Canmore operations is not available, but the following notes have been prepared to accompany references where more complete information about the operations and problems encountered may be found. The coal measures at Canmore occur in the Kootenay formation of Lower Cretaceous age, and at least twelve seams of varying thickness and horizontal extent have been recognized. The coal, of high quality, ranges from semi-anthracite in the lower seams to low-volatile bituminous in the upper seams. The strata of the Canmore area form an asymmetric syncline, the western limb being overturned to vertical by the Palaeozoic strata of the Mount Rundle Range. The eastern limb is more gently sloping, its dip ranging from IO to about 40 degrees. Tectonic movements have created a troubled and complex coal field. The seams were initially not regularly or uniformly deposited, and mountain-building activity folded and faulted the strata and in many places sheared and crushed the original structures of the coal(l,2,3,4,5). The lack of continuity of the seams, and changes in thickness and inclination, made longrange mine planning difficult and necessitated flexible methods of work, and the local disturbances sometimes created problems in roof support and contributed to the occurrence of sudden outbursts of coal and gas. Almost all of the coal was produced from underground operations but a few relatively small V-cut mines were worked along surface outcrops. These have all been filled in and revegetated. The basic method of underground work was by room-and-pillar, but many variations in layout and sequences were employed. Gangways were driven along the strike and pillars were formed by raises or slopes and crosscuts. Pillars were recovered to the extent that ground conditions permitted by splitting or taking 'skips' from the sides of the raises or splits or crosscuts. Because of the variety of conditions that existed in the field a considerable range of cutting, loading and support methods were employed, including hand-loading, slushers and scrapers, duckbills and shaker conveyors, mobile loaders and continuous miners. Except for the coal obtained by continuous miners most of the coal was broken out by blasting when driving narrow working places or by air picks when cutting from a face. In the early years hand loading onto cars or conveyors predominated. A continuous miner was introduced into Canmore in 1959 on a trial basis, and another was subsequently acquired, in order to minimize blasting and hand loading, but problems in operating these machines in inclining seams and difficulties in providing safe roof support for the machines and workers restricted their efficient use. Another major difficulty with the use of continuous miners was the problem of ventilating development headings in the very gassy conditions. In the early 1970s they were replaced by electric and compressed air slushers and scrapers, resulting in a general increase in productivity, roof control, safety, and flexibility of operations(1.6,7,8.9)."

Jan 1, 1985

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982

By Baseer Abdul, Edouard Asselin

Hydrometallurgical leaching of sulfide concentrates of copper and nickel at medium temperature (150°C) produces residues that contain sulfur and iron bearing minerals and phases. During leaching, and depending on various process parameters, iron may be precipitated as hematite, goethite, jarosite or other oxyhydroxides, which may be more or less crystalline. Hematite is the favored precipitate because it is the most environmentally stable and does not ad/absorb as much copper, nickel or other solution constituents during precipitation. However, the low solubility of iron during the medium temperature processing of sulfide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. In some cases these phases have been positively identified as the metastable ferrihydrite, which transforms into iron oxides such as goethite, hematite and magnetite over time. A better understanding of what may help drive this transformation during leaching would ultimately result in lower valuable metal losses and more stable leach residues. Higher acid concentrations result in increased copper extractions and favor the formation of hematite during concentrate leaching, rather than other metastable phases. Furthermore, commercially available water displacement formula “WD40®” and other novel reagent(s) affect Fe precipitation and sulfur chemistry, leading to very different process outcomes such as improved extractions and larger, more easily separated, sulfur particles.

Jan 1, 2017

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, Z. S. Abisheva

"Phosphorus slag is the most heavy-tonnage waste of yellow phosphorus production, which is stored in the dump fields for many years creating ecological problems in the regions. Despite of the actions taken to utilize the slags, most of them remain in the slag disposal area. One of the relevant and priority directions is rare-earth metals production (REMs), presence of which in the phosphorus slags allows considering the latter as an acceptable raw material source. Phosphorus slags contain about 30–40 wt% of silicon dioxide, therefore they can serve as a source of production of precipitated silicon dioxide highly required in different industries.The purpose of this work is the most complete REMs recovery in the solution while leaching and subsequent processing of siliceous cake. The work shows results of researches on establishment of the chemical and phase compositions of phosphorus slags, determination of the forms of presence therein of REMs compounds, processes of phosphorus slag leaching by nitric acid and processing of produced siliceous cake by NaOH solution.Based on the data of the instrumental and chemical methods of phosphorus slag analysis, it was established that it consists of pseudowollastonite a-CaSiO3 for 90–92%. It was found out that REMs are present in it in the form of carbonate apatite Ca10(PO4)6CO3 or rare earth apatite, and La2S3 compound inclusions.Optimum parameters of phosphorus slag leaching process were selected: HNO3 concentration 7- 7.5 mol/L; L/S ratio = 2.6–3 mL/g; temperature – 50–80o?; duration – 1 h; pulp stirring – 500 rpm. Recovery of SREMs, CaO, Al2O3 and Fe2O3 into the solution were achieved at 98.0, 99.1, 99.0 and 18.8%, respectively. Presence of 10 elements of the rare earths group in the phosphorus slag was established. It was found out that recovery of almost all REMs is within ~92–99%, except for Sc and Lu – ~39% and ~28%, respectively.For the purpose of optimization of siliceous cake leaching by NaOH solution, influence of some physical and chemical parameters was studied: N?O? concentration, L/S ratio, temperature, and duration. Results of the experimental data will serve as a basis for development of the technology of complex processing of the technological waste of phosphorus industry with production of REMs concentrate and precipitated silicon dioxide."

Jan 1, 2016

By Chunlin Chen

Published data on thermodynamics of tin in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The developed model/database was applied in modelling the Sn deportment in primary copper smelting and e-waste melting processes. The results show that Sn can be removed from the matte through evaporation of various volatile Sn species (with SnS the most volatile) and slagging during copper smelting. The Sn removal increased with increasing matte grade due to the increased gas and slag volume. In the e-waste smelting process, fluxing strategy was developed for smelting e waste to produce a slag with reasonable liquidus and viscosity. Modelling results show that very low amounts of Sn reported to the gas phase due to low S, hence low SnS partial pressure in the system. The black copper produced could contain a few percent of Sn depending on the oxygen potential. The Sn in the black copper could be removed to the slag phase during anode refining. INTRODUCTION Tin is an impurity element commonly found in copper ores, which will be dispersed into various solid, liquid, and gaseous streams during the pyrometallurgical processing of copper. Tin alloy is widely used in electronic soldering due to its low melting point. The growth in treatment of recycled e-waste through primary and secondary copper smelting has led to an increased tin input to the smelting system. Therefore, the deportment of tin between phases is of great interest to the operators of modern smelters. Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems (Zhang et al., 2002). Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature system (Chen, Zhang, Wright, & Jahanshahi, 2006). In the present paper, the thermodynamic data on tin in liquid copper, matte and slag have been reviewed, assessed and used in the development of a database for Sn slag, alloy and matte phases. The model/database was applied in modelling the tin deportment in primary copper smelting and e-waste smelting processes. The aim of this study is to provide a better understanding of the chemical behaviours of tin in high-temperature copper processing and e-waste smelting.

Jan 1, 2019

By R. G. Bradbury

The paper uses two hypothetical, but typical, situations to show that hydraulic rock drilling equipment has very significant economic advantages over pneumatic equipment both in drifting applications (even in the situation where advantage is not taken of the high productive capacity of the hydraulic drill) and production drilling applications. Other factors, including the non-economic advantages and the disadvantages of hydraulic drilling, are discussed. The paper concludes with a brief analysis of why the Canadian mining industry has been slow to take advantage of this apparent broadly advantageous advance in rock drilling technology.

Jan 1, 1979

By Z. D. Hora

Traditionally, industrial minerals in British Columbia comprise about 10 per cent of the combined value of mineral, coal, petroleum and natural gas production. Over the years a wide variety of industrial minerals have been produced in British Columbia, often with a different level of marketing success. For some products such as building stone, common brick or expanded shale, once strong demand gradually disappeared; for others such as asbestos and barite, new discoveries or new industrial activities created demand and new markets. For yet other minerals such as fluorite, talc and perlite, wider use has been prevented by the small size, poor quality or remote locations of the deposits. Bentonite (1926 to 1944-as a by-product from coal mines) Building stone (intermittently since the mid-1800s) Chromite (1918 and 1929) Over the past years, the list of industrial minerals produced has been expanded to include several new commodities: glassgrade silica sand, magnesite, pumice and silica for ferrosilicon and silicon carbide manufacture.

Jan 1, 1984

By T. R. C. Aston, C. M. K. Yuen, J. L. Gilby

"The access tunnels for the Donkin-Morien Mine in Cape Breton, Nova Scotia, comprise two parallel tunnels driven through a sedimentary sequence of sandstone, siltstone and mudstone to intersect the Harbour Coal Seam under the Atlantic Ocean, approximately 3.5 km offshore (Fig. 1). The No. 2 tunnel was driven a total distance of 3579 m using a 7.6 m diameter Loyat full-face tunnel boring machine (TBM) and was supported by steel sets. The No. 3 tunnel was initially driven a distance of 1027 m using drill and blast methods (dimensions 7.6 m wide by 5.3 m high) supported by rock bolts and shotcrete. This tunnel was then completed (front March 1986 to February 1987) using the tunnel boring machine to a distance of 3573 m.During the period May 1983 to December 1984, a major geotechnical research program was undertaken in the Donkin-Morien tunnels by Golder Associates in conjunction w,ith CANMET and the Cape Breton Development Corporation (Yuen et al., 1985). The research program included the monitoring of the performance of the TBM and drill and blast drivages, and the study of the thrusting characteristics and rock-interaction of the TBM excavation. The main emphasis of the research program was on the collection of field data which was to be made available in the form of a comprehensive report for the future use of others who might wish to carry out a detailed interpretation and analysis. The information gained from the program was also used during the tunnel"

Jan 1, 1988

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

By C. O. Campbell

THE recognition by C. W. McKee, field engineer for Springer Sturgeon Gold Mines, Limited, in the fall of 1940, of the economic possibilities of a small outcrop of baryres near Pembroke, in Hants county, Nova Scotia, followed by aggressive exploration and development by the Company, has placed Canada for the first time in its history in the position of becoming a major producer of barytes and its products. In past years, production of this mineral in Canada has been unimportant. Thus the coral output from 1885 ro 1933, inclusive, amounted to only 41,027 short tons, following which there was no production until 1939. Deposits in Nova Scotia, and particularly in the Lake Ainslie district, Cape Breton, have been the main source of supply, with a production between 1866 and 1925 of 31,689 tons. Following the examination of the outcrop of baryres near Pembroke by Mr. C. W. McKee in October, 1940, the area surrounding it was trenched, and, as this work gave encouraging results, a diamond drilling programme was commenced. A grid system was laid our and sixteen holes aggregating 2809.3 feet were put down, spaced at 100-foot intervals, the deepest hole being 300 feet. This drilling outlined a body of high-grade baryres over 600 feet long and 200 to 250 feet wide, with an average depth of 120 feet and estimated to contain well over one million tons of ore. The limits of the body were reached on the west, north, and southwest, but the drilling was suspended before the eastern limit was determined. Quarrying operations, and construction of a 100-ton mill, were commenced in February, 1941. The mill was placed in operation on May 29th, and on June 15th, eight months after the initial discovery, the first shipment of 2,500 long rons of milled baryres was made to Trinidad, British West Indies.

Jan 1, 1942

By I. E. Puddington, F. W. Meadus

The beneficiation of barite in mill tailings using an agglomeration technique has been demonstrated. Barite was selectively absorbed from a conditioned aqueous slurry into a collector oil by mechanically mixing slurry and oil. The resulting oil-bonded barite-containing agglomerate was washed, to remove gangue material, and further mechanically contacted with dilute H2SO4 This treatment resulted in the transfer of barite into the aqueous phase. Grades as high as '97% BaSO4, with recoveries of 80%, have been obtained using this technique.

Jan 1, 1973

By Z. Y. Ma, H. Y. Yang

The process of microwave-ultrasound assisted leaching of valuable metals from copper anode slime was proposed in this paper. Design of experiments has been used to study the effect of the main leaching parameters, such as microwave power, ultrasound power and reaction time. The central composite design (CCD) was used to predict the maximum leaching efficiency of copper, tellurium and selenium. The experimental data obtained were fitted to a second-order polynomial equation, and they also were analyzed by analysis of variance (ANOVA). The 3-D response surface plots and the contour plots were applied to determine the optimal conditions. The optimum conditions of microwave-ultrasound assisted leaching process were: microwave power 834W, ultrasonic power 638W and reaction time 403s. Under these conditions, the experimental leaching efficiency of copper, tellurium and selenium were 98.88±0.56% 98.96±0.78% and 98.57±0.67%, respectively, which agreed well with the predicted values.

Jan 1, 2014

By Randolph A. Pax, Brian Cornish

The operation of grinding mills in an ore processing circuit is supported by monitoring the input and output variables. These can include the feed ore size distributions, ore feed and water addition rates. The outputs can include the discharge undersize density, oversize tonnage rate and the P80 of the discharge. The grinding mill performance is judged by the power draw, recycle rates and discharge grind size. Conditions inside the mill are inferred from loads cells or bearing pressures and past histories. An overall noise value is sometimes used to evaluate the load as well as the occurrence of excessive impacting of steel balls onto the liners/lifters of the mill. This paper presents results of the internal behaviour of a mill using non-contact stationary microphones located close to the mill outer shell (Pax, 2012). The noise generated by a mill can be attributed to a number of events that occur inside these mills and suitably analysed can provide real-time determinations of in-mill behaviour and can provide powerful insights into the operation of the primary comminution tumbling mills. The acoustically determined signals including a specific 'steel' signal, water hold-up, integrated area together with a classification of impact events. Specific results from case studies will show information of the trajectories inside a mill, steel to rock ratio as well as rheology effects. By incorporating a self-consistent understanding methodology for the in-mill processes from an array of microphones, the information can be used to diagnose the dynamic conditions inside a mill.

Jan 1, 2016

By M. Somppi, D. Weirmeir, Z. Yamak

"Milling operations commonly employ activated carbon to capture complexed gold from lixiviants in leaching processes. As the carbon moves through pipes, pumps, vessels, kilns and other processes in the gold leaching circuit, this consumable may experience losses by various mechanisms like attrition, breakage, and rupturing. Whenever possible, capturing the fine gold-bearing carbon portion of this stream could provide value to milling operations at low capital cost and manageable financial risk. Identifying, testing, and validating the successful payback of a low-tech flocculant system is described. However, the work more closely explores a Monte Carlo risk-based methodology for understanding the potential payback of this project at various confidence levels – an approach that many improvement projects can follow where some level of uncertainty exists.INTRODUCTION Gold milling operations commonly employ activated carbon to adsorb gold from solutions. Normal handling causes the carbon particles from this material to abrade, break, rupture to a size that becomes too small for further use in the process. Operations often concentrate on capturing the fine particles because gold is associated with the carbon and this metal content can be a valuable revenue stream for toll processing. However, the small particle sizes become difficult to separate from the process and can ultimately leave the facility in the waste stream. Hence, operations often place a great deal of care in capturing as much fine carbon as possible by a variety of methods including using screens, settling tanks, and chemical methods. Retrofitting a circuit to capture more carbon fines is common but can expose the operation to financial risk. Approaching this potential improvement by leveraging a Monte Carlo methodology can be effective in understanding the risk and the associated payback of a project at various confidence levels. This method provides a strong framework for capital go-no-go decisions and the structure to validate the potential project success before implementation."

Jan 1, 2019

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014