Search Documents

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

By Thomas M. Ware

"MR. Chairman, our Honourable Minister, Mayor Cole, it is a pleasure for me to come here, and join with you in one of the largest industrial shows ever held in Saskatchewan.It is an honour to be asked to keynote your meeting, to help mark an early chapter of this new industry for Saskatchewan. God has placed in our hands a new resource for His man on earth. This store of potash, 350 million years in the making, offers a vital resource to help man support his advanced intellect for thousands of years. It is a gift so large we must all wonder at its purpose and our responsibilities in serving our fellow man with it.We who are here to plan and implement the development of this essential mineral resource enjoy a great -privilege; and we share a great responsibility -to see that the billions of tons of potash which have waited beneath these prairies for millions of years are widely and wisely used to nourish the earth through future millenniums.To know the true value of potash, to be able to bring forth this re-source from over 3,000 feet deep in the earth, to establish markets and develop its potential worldwide is all part of our great heritage from generations past. So I think it is fitting on this occasion that we reflect for a moment on this heritage, to help us assess the responsibilities of its future development."

Jan 1, 1966

By Barry W. Schmitke, J. M. Marino

"Cigar Lake Mining Corporation is presently operating an underground test mine in northern Saskatchewan, with a view to developing a high grade uranium deposit. The mining test is intended to demonstrate that the innovative mining methods designed are safe and economical. Two vertical mining methods are considered for the test:• box hole boring from the lower level;• blind boring from the upper level.In both cases, it is anticipated to freeze the ground before excavation to ensure hole stability and limit the inflow of water. Special care will be taken to minimize radiation exposure of personnel.Remote controlled equipment will be used where applicable.The access to the orebody was an important component of the test. After shaft sinking to a depth of 500 m, development work commenced at the 420 level in fractured sandstone which was grouted to restrict the inflow of formation water. The drifting continued in a section of poorly consolidated sand, clay and sandstone; this area was frozen to allow stabilization prior to excavation. At the 480 level relatively little water was encountered in the altered basement gneiss and grouting was not necessary; however, extensive ground support was required in the soft ground areas."

Jan 1, 1992

"Beneficiation of low grade ores is the process of increasing the grade of a mineral through unit operations that remove and separate the waste (or gangue) material from the valuable mineral that can then be used for further processing or direct use. Important factors when deciding upon a beneficiation program are the feed grade, mass yield and the metal recovery. As lower grade ores are being processed beneficiation is a critical process. How predictive is laboratory test work for “as built” operating projects? Beneficiation includes all or some of the available unit operations to produce a beneficiation flow sheet i.e. associated unit operations including but not limited to optical sorting, radiometric sorting, crushing and screening, coarse cobbing, jigging, dense media separation (DMS), spirals, magnetic separation, flotation, thickening, filtering and drying. Reference to specific projects and the approach developed in formulating a beneficiation flow sheet and a comparison of difficult and simple beneficiation flow sheets are cited. INTRODUCTIONReserves of high-grade iron ores are reducing all over the world, at an alarming rate, over the years as a result of the rapid increase in demand for steel particularly from Japan and then China. The recovery of mineral value from the low-grade ores using present technology is more expensive than DSO ores due to high energy and capital costs. Beneficiation is defined as a variety of processes whereby extracted ore from mining is reduced to particles that can be separated into mineral and waste.Various physical properties of an ore can be exploited to separate a low grade fraction including variation in hardness, density, reflectance, conductivity and magnetism.""Beneficiation"" of iron ores includes concentration, generally by physical removal of unwanted gangue. Also considered beneficiation is the regulation of product size, or other steps such as agglomeration to improve its chemical or physical characteristics prior to smelting."

Jan 1, 2012

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

By A. Warczok

The computer simulator of slag cleaning in an electric furnace is based on a set of mathematical models describing heat liberation, the rate of slag reduction and gravitational coalescence of matte and metallic copper inclusions. The simulator consists of a mass and heat balances as a frame, in which the kinetic equations of the slag reduction and phase separation are incorporated. Friendly user-screen interface allows for dynamic control of process parameters in real time together with simulation of typical operations, such as furnace charging with liquid slag, solid reverts and coke, tapping out of the slag and matte, motion of electrodes and control of the transformer. The batch, semi-continuous or continuous process can be simulated. The process parameters are displayed and continuously recorded for further analysis. The computer simulator is a powerful tool for process optimization, training of furnace operators and the design of new slag cleaning installations.

Jan 1, 2007

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By W. Dong

This paper presents the fundamental study of the temperature distribution in a reforming planar solid oxide fuel cell (SOFC) using mathematical modeling and experimental testing approaches at Versa Power Systems (VPS). In order to investigate the on-cell temperature distribution under high rates of Natural Gas direct internal reforming (DIR), both the computer simulation approach and the experimental testing approach have been developed. In this work, comprehensive in-house DIR and SOFC models were developed and employed for the computational fluid dynamics (CFD) based 3D computer simulation. The current SOFC module has been corrected to take into account both the on-cell electrical leaking effect and the stack stage structural resistance. Meanwhile, an instrumented single-cell test jig with multiple thermocouples was built, and a series of experimental tests were performed at various conditions. The numerical results based on the single-cell jigs are in very good agreement with the physical test results.

Jan 1, 2005

By N. Dahata

Earlier research has indicated that an addition of titanium master alloy to aluminum alloys, results in improved fillability, grain refinement and finer pores. B206 alloy differs from other alloys used in automotive industry, with lower titanium level. This paper examines the effect of alloy chemistry (copper and titanium levels) and grain refinement (A1-5`)oTi- 1%B grain refiner) on grain size, microstructure and microporosity in B206 aluminum alloy. In this study, characterization of grain size, microstructure and microporosity was carried out using light optical microscopy (LOM) and scanning electron microscopy (SEM). Results have shown that the addition of 0.05 wt % titanium resulted in grain refinement of B206 alloy. With an increase in titanium to 0.25 wt further grain refinement, much reduced pore size and uniform distribution of pores resulted. These results suggest that B206 with proper addition of titanium has a promise as an alloy for automotive casting.

Jan 1, 2007

By C S. Stevens

This paper describes the problems encountered and the steps taken to solve them in milling an ore containing relatively large amounts of pyrrhotite. A complex and greatly lengthened flotation circuit was required to recover the pyrrhotite. A very low pH had to be maintained in the cyanide circuit in order to get good recovery of the gold and maintain reasonable cyanide recovery. Introduction D ELNITE Mines Ltd., a gold mine situated about 5 miles by road south and east of the town of Timmins, Ontario, is serviced by two shafts. No. 2 shaft extends from surface to the 2875-ft. level, and No. 3 shaft, an internal winze, extends from the 2875-to the 5275-ft. level. No. 2 shaft was stopped at the 2875-ft. level because of a heavy band of chloritic schist which necessitated a drive to the north for 1000 feet, where No. 3 shaft was sunk. The latter bottomed in the schist at the 5275-ft. level. From the 2500 to the 2875-ft. level in No. 2 shaft, the ore was

Jan 1, 1965

By Maurice Morton

THE use of organic and inorganic stains has found wide application as a means of detection and estimation of organic fibres. Such stains have enabled the analyst to distinguish between organic fibres of different type and even between wood fibres produced by different processes. Among these stains, aqueous iodine solutions have figured prominently, as in the case of the well-known Sutermeister and Herzberg stains. At the Johns-Manville laboratories, the idea of applying a stain to asbestos fibres was first considered solely as a visual aid in the microscopic examination of such fibres. The staining medium used in this work consisted of a 1 per cent solution of iodine in C.P. glycerine, the latter being used extensively here as a dispersing and mounting liquid for asbestos fibre. This iodine solution was found to have distinct staining properties when used on the local chrysotile fibres, and to improve greatly their visibility under the microscope. It was soon revealed, however, that this staining is apparently limited to the chrysotile variety of asbestos, as against other varieties. It can be readily seen that, if such were the case, the staining test would become a very useful tool in differentiating between chrysotile fibre and the other mineral fibres, without recourse to a lengthy chemical analysis. Hence this investigation was launched, with the purpose of obtaining more information as to the selectivity of this stain as well as its mechanism. The only previous work of this nature that could be found in the literature was that of Van Winsen and Graham (1, 2, 3) on the adsorption of erioviolet dye by serpentine and related magnesia minerals. However, these authors did not refer to any specific behaviour of chrysotile as against other types of asbestos fibre.

Jan 1, 1941

By Jean-Loui Frenetie, Françoi Himbeault

"Flow of traffic in the underground mine has been improved through the years with clever use of traffic lights. The evolution is characterized by three major design changes. This paper will scan the basic criteria of these designs.IntroductionMines Gaspe, formerly known as Gaspe Copper Mines Limited, is a member of the Noranda Group of companies. The mine is the ""raison d&apos;etre"" of the town of Murdochville, located 600 m above sea level on the Gaspe Peninsula. Paved highways link the town with Gaspe, 95 km to the east, and with Anse Pleureuse, 400 km to the north, on the Gulf of St. Lawrence.The low-grade copper mineralization was discovered in 1921 at Copper Mountain by local prospectors, the Miller brothers. Noranda Mines Limited obtained an interest in the property in 1937. World War II interrupted exploration work and it was not until 195I that a decision was made to bring the property into production.Initially, operations were confined to the Needle Mountain underground deposits which commenced production in 1955. Between 1968 and 1982, low-grade ore from the Mountain open pit supplemented the production. Due to the depressed market, surface and underground operations were suspended in 1982. Needle Mountain underground mining resumed in the second half of 1984, but the Copper Mountain open-pit operation remained idle. Since 1979, more than 75 km of exploration drilling resulted in the discovery of two new deposits, one which is located under the town of Murdochville . Mines Gaspe&apos;s present ore reserve, approximating 8 million tonnes, will be depleted by the end of 1992."

Jan 1, 1988

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By R. Heikkilä

A large research and development program called RYM PRE (Process Re-Engineering) has been active in Finland since 2010. As a part of the program, a work packet Infra FINBIM is focused on the development of new national process model, specifications and requirements for the whole Finnish Infra Industry. In the Infra FINBIM, total 15 companies and main owners and 3 research organisations are included. The work is further continuing. The main achieved results up today have been the first specifications and requirements of the BIM based total process for infra sector, about 30 different pilot projects for testing of the new design and construction process models producing a lot of results and observations, a new open information transfer format Inframodel3 based on LandXML standard, the achieved acceptance of the Building SMART organization for support of international development, utilization and extension of the format within the whole infra industry, processes, software and other technical equipment. An evaluation of the results and this work will be drawn.

Aug 1, 2013

By Peter Moon

THE mineral industry of Canada relies heavily upon the talent of its technical men. It is vital to the well-being of the industry that its supply of young, trained men be adequate. At the present time, the industry is acquiring only 200 new graduates a year. The shrinking supply is far below present and future requirements. Other industries and research organizations are competing for engineers and scientists. Dr. J. B. Mawdsley (1), Past-President of the Canadian Institute of Mining and Metallurgy, has recently outlined a program designed to attack the problem. Dr. J&apos;. C. Sproule (2), another former President of the Institute, has stated that: "The need for selection of trainee material is commonly recognized, but little is done about it." The following paper contains a short discussion of occupational interests, and outlines research, using psychological knowledge and measuring techniques, aimed at the identification of desirable recruits for the mineral industry.

Jan 1, 1963

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By M. Bouchard et G. Martineau

In the Chibougamau area, a large portion of the glacially tranported boulders which were deposited at the surface were later partly remobilized by the waters of Glacial Lake Ojibway. In the dispersal studies of these boulders, it is sometimes difficult to discern the effect of this reworking process. In addition, depositional processes in the lake contributed material to the original block deposits through the formation of boulder lag by littoral wave action and through direct sedimentation in the form of deltaic deposits. In spite of these complicating factors, dispersal studies at carefully selected sites which were unaffected by the above processes make it possible to unravel the general patern of glacial dispersion. In this study, indicator lithologies of the Albanel and Chibougamau formations were used. They give a coherent image of dispersal throughout the area showing transport toward the southwest. Considering the particular geological context of the region, and in view of the extensive mineral exploration studies which are being carried out, the results of this study are encouraging for the tracing of source areas of glacially transported mineralized boulders.

Jan 1, 1984