Search Documents

By Hugh P. Godard, K. Winslow

"AbstractA number of panels of various aluminum alloys in different combinations and secured by steel and three types of aluminum rivets were exposed underground at two locations in a Northern Ontario gold mine for two years and then examined to determine the extent of corrosion. The results indicate Alcan 65S-T to possess considerable advantages over Alcan 178-T, which has been employed in the construction of light skips and cages with considerable success for almost twenty years. Information on the behaviour of these alloys when used with steel rivets and in mixed combinations with themselves was obtained.IntroductionBy the complete substitution of aluminum alloys for steel in the fabrication of mining skips and cages, their weight can be reduced as much as 50 per cent. Lesser savings are possible though its savings are possible through its plates, doors, reinforcing members, etc. Reduced weight leads to economy through increased hoisting efficiency.For a new installation, the basis of design is the rate of production, which thus fixes the live load to be hoisted per trip. A lighter skip permits the use of a lighter rope and a smaller hoist. In deep shafts with high-speed hoists operated in balance, the power required for accelerating is considerable. The hoist size is determined by the weight of skip, load, and rope plus the force required to accelerate or decelerate these three elements A light skip may result in a considerably lighter rope. This is important because, even though the skip can be completely balanced this is not true of the rope. Partial balancing is possible, but conical hoist drums or other devices for this purpose are costly; thus a smaller rope results in a smaller hoist, with consequent general reduction in cost of the whole installation. A reduction in power consumption is also obtained as a result of keeping to a minimum the amount of unbalanced load and the weight of all moving parts which must be accelerated."

Jan 1, 1950

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017

By A. M. Glendinning

"IntroductionLocationTHE PROPERTY of Aunor Gold Mines, Limited is in Deloro township, Ontario, about three miles southeast of the town of Timmins. It consists of a group of eleven claims located between those of Buffalo-Ankerite Gold Mines, Limited, and Delnite Gold Mines, Limited.GeologyThe ore zone at the Aunor mine consists of a narrow band of fine grained pillowed andesite, irregular bands of 'brown to green carbonated andesite, and lenticular bodies of quartz feldspar porphyry. The zone strikes N.80°E., dips 60 North, and has been traced for 5,000 feet across the property. It varies in width from 0 to 250 feet and is bounded on the north and south by masses of dark bluish-grey tale chlorite schist. These schist bands have widths up to 500 feet.The ore occurs in a series of parallel and branching veins confined to the limits of the zone. These veins tend to terminate and die out on the footwall schist contact, striking generally parallel with the ore zone. In wide sections of the zone, 150 to 250 feet, the veins range in width up •to 3.5 feet and may occur in two or three horizons across the width of the zone, each mineable independent of the other. They tend to dip a little flatter than the general dip of the zone. Where the zone is narrow, the veins are so closely spaced and numerous they can be mined together and in some places the complete zone has been mined from schist to schist."

Jan 1, 1953

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

ABSTRACT Inco’s Iron Ore Recovery Plant was operated by Inco from 1955 to 1980 near Sudbury, Ontario. As exposures to specific nickel substances have been associated with adverse respiratory endpoints it is important to understand processes giving rise to such substances. This manuscript discusses the process and equipment, the propensity for aerosol formation, and operational procedures used by Inco in roasting a pyrrhotite concentrate, reducing the nickel in the formed oxide, leaching the nickel in ammoniacal solution, purifying the resulting solution, making green or black NiO, and producing iron oxide pellets. Industrial hygiene measurements are also reported.

Jan 1, 2013

By Herbert D. Drechsler, James B. Stephenson

"AbstractThe paper identifies the major components of price change which affect the determination of the internal rate of return of a mining project. It illustrates several price indexes which may be used to measure general price increases, identifying techniques which might incorporate them into mine valuation procedures. The ""hurdle rate"" for new investment is discussed.IntroductionDECISIONS regarding the value of an orebody and whether or when to mine an orebody are based on an estimate of the cash flows which would be associated with its exploitation. These pro-forma cash flows represent cash in or out of a possible mineable deposit and include exploration and construction costs, sales revenues, operating expenses, taxes, debt borrowings, interest and debt repayment. It has long been recognized that when combining the cash flows occurring over the life of the mine, dollars received or paid out early have greater value than those received or paid out later. This time value of money has been incorporated into mine evaluation calculations through the use of present-value or discounting techniques. Another factor affecting mine valuation, inflation, is not accounted for by valuation techniques now in use. In recent years, price changes have become more volatile. In the past, price change could easily be ignored when evaluating potential mines. Today, the combination of larger investments and greater price volatility leads to great concern about the effects of price change on mine valuation."

Jan 1, 1977

By H. Brodie Hicks

"THE REVIVAL of the Mayo mining camp, with particular reference to the activities of United Keno Hill Mines, Limited, has been one •of the more spectacular and also one of the most important of the post-war developments in the Canadian mining field. The geological location of the camp, coupled with other natural disadvantages, have in the past limited the mining area to small-scale, highgrading operations, but the post-war improvement in metal prices has now broadened the possibilities and has led to the considerable success achieved by United Keno Hill Mines, Limited, and the present boom-type development by a whole host of newcomers to the field.LocationYukon which has an area of 207,000 square miles, is showing ever increasing possibilities as a mineral source of great value and more and more attention is being focussed on the Territory. The accompanying generalized map (Figure 1) shows the main transportation routes and mining districts.The Mayo Mining District comprises roughly the eastern two thirds of Yukon Territory lying north of McMillan river and south of the Peel. The district was one of the first in the Territory in which placer gold was discovered, but the occurrences proved of minor importance. Other minerals reported include ores of tungsten, tin, antimony, and several other metals, but of primary importance have been the ores containing silver-lead-zinc-cadmium now being developed and mined in the Keno area. Similar ores have been found over a very considerable area, extending some 50 miles north, 15 miles east, 30 miles west, and 10 miles south of the townsite of Keno Hills, Keno City, a total area of 2,700 square miles."

Jan 1, 1952

By M. Mai Manga, M. Renaud, A. Faucher, C. Bazin

ABSTRACT Grinding circuits are operated in the presence of disturbances resulting from ore changes and equipment malfunctions, such as hydrocyclone overloading, worn or partly plugged apexes, surging, and internal liner detachment that may cause a loss of classification performance. Metal recovery losses in downstream leaching or flotation circuits justify the development of methods for rapid detection of hydrocyclone malfunction. Two methods are presented in this paper. The first method uses measurements from sensors available in a grinding circuit and the second uses vibration sensors installed on the individual hydrocyclones of a nest.

Jan 1, 2011

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By K. C. Grogan

"GeneralGIANT ORE is complex, with the gold values for the most part occurring in extremely close association with arsenopyrite, stibnite, jamesonite, and a wide group of antimonial minerals locally termed 'the grey minerals'. Pyrite is the most abundant of the sulphide minerals• and minor quantities of chalcopyrite, galena, and sphalerite also occur. Pyrrhotite has been found in some sections of the mine, but to date none of it has been nickeliferous. Native gold occurs in varying amounts throughout the ore bodies.In 1944, ore dressing investigations were commenced on diamond-drill core rejects and samples of surface outcrop ore. Results soon indicated that treatment to produce satisfactory recovery of the gold values would involve fine grinding to 80-85 per cent minus 200 mesh, recovery of free gold by jigs, followed by flotation, roasting of the flotation concentrate, and subsequent cyanidation of the calcine. Proceeding from this information, the flow-sheet was prepared, plant design worked out, equipment purchased, and construction of the treatment plant commenced in May, 1947.The crushing, grinding, and flotation units of the plant were rushed to completion and commenced operation on May 12th, l.948, at 225 tons of ore per day. This rate was maintained until January 27th, 1949, when the Allis-Chalmers roaster and cyanide plants were completed and commenced operation. During the period May 12th, 1948, to January 27th, 1949, gold recovered by amalgamation was the sole source of revenue. Flotation concentrate was stockpiled pending the completion of the Allis~Chalmers roaster and cyanide plants."

Jan 1, 1953

By Pingchao Ke, Zhihong Liu

"To overcome the problem that scoroditeis not stable in neutral and alkaline solutions, we proposed and investigated a synthesis method of scorodite coated in-situ with hydrated ferric oxide in the Fe(II)-As(V)-H2O system at the initial Fe(III)/As(V) molar ratios larger than 1.0.The synthesis was carried out at 90?,pH 1.5 under atmospheric pressure. During the synthesis, oxygen gas was conducted and bubbled into the system to oxidize Fe(II) ions into Fe(III)ions, and Na2CO3aqueous solution as neutralizing agent was added controllably into the system for keeping the pH constant at 1.5. In this study, three samples of scorodite were synthesized at the controlled initial Fe(II)/As(V) molar ratios of 1.0, 2.0 and 3.0, respectively. The characterizations of the samples by HRTEM, TEM/EDX, and chemical composition indicated that the particle surfaces of scorodite synthesized at the initial Fe(II)/As(V) molar ratio of 2.0 and 3.0 were coated in situ by a film of hydrated ferric oxide with the thickness of several nanometers, while the sample synthesized at the initial Fe(II)/As(V) molar ratio of 1.0 was uncoated scorodite. The TCLP and long-term leaching for the toxicity characteristic of the samples showed that scorodite coated in situ with hydrated ferric oxide was stable in a wide pH range from 3.0 to 10.0, with the arsenic concentrations in the leaching solutions less than 1.0mg/L. Nevertheless, uncoated scorodite was unstable under the conditions from weak acidity to alkalinity, with the arsenic concentrations in the leaching solutions larger than 5.0 mg/L.INTRODUCTIONArsenic pollution is a challenge for environment and health and has been an important issue for scientists (Hopkin, 1989).Arsenicis commonly associated with ores or concentrates of nonferrous metals, mainly as independent arsenic bearing minerals such as arsenopyrite (FeAsS), tennantite(Cu12As4S13), enargite (Cu3AsS4), cobaltite (CoAsS), and gersdorffite (NiAsS), realgar (As2S2), orpiment(As2S3), etc.(Matschullat, 2000; Mandal & Suzuki, 2002; Long & Peng, 2012). In the nonferrous metallurgical processes, arsenic is enriched mainly in such arsenic bearing materials as various flue dusts, residues, and anode slimes, which results in the accumulation of arsenic in the system owing to the circulation of those arsenic-bearing materials back to the system and the pollution to the environment (Harris, et al, 2003).In addition, the utilization of arsenic is limited and has been decreasing owing to its toxicity and carcinogenicity. Therefore, arsenic has to be removed from those arsenic-bearing materials and discarded safely (Dutrizac & Jambor, 1988; Monhemius & Swash, 1999; Drahota & Fillippi, 2009).In this case, how to immobilize arsenic has become a difficult problem which must be solved. Among the methods of immobilizing arsenic which have been proposed and investigated, immobilizing arsenic into a stable mineral to fix it, has been realized as a promising method and becomes a research focus(Dutrizac et al, 1987; Dutrizac & Jambor, 1988; Demopoulos et al, 1995; Fujita et al, 2008a; 2008b).Scorodite has been known as one of the best minerals for immobilizing arsenic, owing to its high stability under weak acidic condition, the arsenic content as high as 32wt%,and good crystallinity benefiting the separation of solid to liquid(Daivid et al, 1999; Zhu & Merkel, 2001). Scorodite can be synthesized from arsenic containing solutions under both hydrothermal and atmospheric conditions, and a lot of work has been done on the synthesis of scorodite and its leaching stability characterization (Filippou & Demopoulos, 1999; Gomez et al, 2011).Two plants for the immobilization of arsenic as scorodite have been putin to operation in Chile and Japan, respectively (Filippou & Demopoulos, 1999; Amir et al, 2016)."

Jan 1, 2017

TRE ? worldwide leader in InSAR ? Spinoff of Polytechnic University of Milan ? Numerous patents for cutting edge technology (e.g. SqueeSAR?, PSInSAR?) ? Focus solely on InSAR with over 13 years experience ? ISO 9001 quality certification ? Powerful scalable parallel processor to handle all jobs What can InSAR provide for mining? An advanced suite of tools for monitoring ground deformation over mine sites: ? Deformation maps ? A dense network of measurement points ? Time series ? Cross sections of surface profile evolution

Aug 1, 2013

By Xiong Tong, Jiushuai Deng, Yingbo Mao, Lingyun Huang

Ammonium carbamate has been used as a reagent for the leaching of copper from the copper oxide ore found in the Honghe state, Yunnan province, China. In order to find the optimal conditions for the leaching of copper from this copper oxide ore,the effects of several processing parameters, including the concentration, time, temperature, particle size and stirring intensity have been investigated. The results of these optimization experiments showed that the leaching rate of copper reached up to 72.76% under the following conditions: liquid-to-solid ratio of 10:1, ammonium carbamate concentration of 2.5mol/L, leaching temperature of 45 °C, stirring speed of 300rpm, a reaction time of 1.5 h and 85% by weight thereof passes through a sieve having 0.074 mm.

Jan 1, 2015

By Masahiro Eguchi, Giuseppe Granata, Chiharu Tokoro, Hiroki Fukuda, Yuichiro Toba, Shungo Hobo

"Currently, large amounts of wastewater containing boron are discharged from industries like coal-fired power plants. Although coagulation-sedimentation is widely employed for their treatment, only a little consideration has been given to its mechanism. An additional problem is that the produced sludge has poor solid-liquid separation. This study is focusing on coagulation-sedimentation using magnesium, examining the mechanism and improving the solid-liquid separation. First, the co-precipitation with magnesium hydroxide was conducted against high-concentration boron wastewater with 500 mg/dm3as B. Second, in order to improve the solid-liquid separation by maintaining high reactivity, low-crystalline magnesium oxide was synthesized from magnesium carbonate by calcination at 400–700°C. It was tested as an adsorbent of boron and compared to co-precipitation with magnesium hydroxide. Co-precipitation showed high removal capacity. X-ray diffraction (XRD) of the sludge revealed the presence of other compounds besides magnesium hydroxide. This result suggests that other processes play a role other than simple adsorption on to magnesium hydroxide, and provides a plausible explanation for the observed high separability. As for the adsorption, the synthesized magnesium oxide immobilized as much or more amount of boron than co-precipitation. Furthermore, the results of fourier transform infrared spectroscopy (FT-IR) suggested the residual magnesium carbonate improved solid-liquid separability due to its poor solubility.INTRODUCTIONBoron is used in various industrial applications. In glass industry, the addition of a little amount of boron into glass products can enhance heat-resistance and chemical-resistance. Semi-conductor industry also employs boron as dopant for silicon. From these industries, large amounts of wastewater containing boron have been discharged. Additionally, coal-fired power plants have been recently discharging highly concentrated boron wastewater because the amount of boron contained in coal has been increasing due to a gradual decrease of the quality of coal. Since boron is partially proved to be toxic for animals, plants, and human beings (WHO, 1998),the guideline of the World Health Organization limit the boron concentration in drinking water to 2.4 mg/dm3(WHO, 2009).Because boron does not precipitate from solutions by simply changing the pH, the removal could be carried by operations such as adsorption or ion exchange. However, since ion exchange is an expensive operation with relatively low capacity, it is not suitable to treat the large amounts of wastewater produced by heavy industries like the coal-fired power plants. Therefore, coagulation-sedimentation method is still widely used as a suitable alternative way."

Jan 1, 2017

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee's field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By I. Ruiz Bustinza, L. F. Verdeja, Daniel Sbarbaro, R. Parra, J. Mochón

The oxidation of sulfides is a complex process involving gaseous products and intermediate species given rise to emission and absorption spectra which carry out important information about the reaction process. This information could be used for on line monitoring of pyrometallurgical reactor if the appropriate sensors were available. We present in this paper an analysis of the concept that has been successfully applied in iron and steel making industry, as well on fuel combustion control, where the spectra measurement gives the possibility for online monitoring and automatic control of high temperature processes. This concept has not been widely applied in the nonferrous pyrometallurgical primary production. The design of new sensors is discussed from the analysis of spectra measurements during flash combustion of copper concentrates at laboratory scale.

Jan 1, 2015