Search Documents

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By Jacek Paraszczak

For mining companies facing strong international competition and unfavorable commodities? prices, automation of underground operations has got a potential to increase productivity and help cut cost. However, despite considerable technological progress in this field, there still remain some problems to overcome. Furthermore, a success implementation of automation depends also on numerous operational, organizational and even human factors. In this context, this paper reviews briefly a technological progress with regard to different underground operations. Following that, several issues related to implementation of automated equipment and systems are presented and discussed. Particular emphasis is put on the factors whose importance is sometimes underestimated. Some recommendations in this respect are also given. It is stated that a success of an automation project is a function of many ?winning conditions?, which may be created through a very thorough planning and preparation. It is also underlined that despite achievements made, a vision of a man-less underground mine is not yet a question of near future as it may seem.

May 1, 2001

By Michael W. Russnak

Productivity and operating expenses are everything when it comes to judging how well your mine and company are doing. Stakeholders are always looking at these numbers and trying to understand if productivity is improving, if operating costs are trending downward and what you are basing your decisions on. o make improvements you first need to understand how you are performing. If you can?t get this basic information, you will never improve. You will not be able to make simple decisions related to maintenance, operations or production. Forget about planning, as you will only be guessing based on the numbers some stakeholder or your executive wants to see. The problem miners run into is not that the data doesn?t exist; it does, but typically it?s raw, it?s everywhere and its volume is huge. Today there is more on-board computing capability in shovels than we had on our desktops three years ago. Add other mobile equipment, plant systems and multiple OEM vendors to the equation and the challenge is daunting.

May 1, 2007

By K. A. Clark

SEPARATION of the oil from the bituminons sands of the Athabaska area of Alberta has been a subject of study by the Research Council of Alberta. The results of the study have been published in the Annual Reports of the Council. However, the last Annual Report in which there is mention of bituminons sand separation is that for 1934. The attention that is being directed toward the bituminons sands at the present time calls for an up-to-date summary of the work of the Research Council of Alberta on the hot-water separation process. STATEMENT OF FUNDAMENTALS OF HOT-WATER PROCESS Studies of the hot-water separation process have been largely empirical in nature. The objective sought has been a complete recovery of oil from the sand in the form of a separated oil which, itself, is free from mineral matter. Various procedures have been tried in the hope of attaining this objective and a very considerable mass of observations and background of experience have been acquired. lt is rime that a theory for hot-water separation should commence to emerge. As a start toward the formulation of such a theory, the statements which follow regarding the constitution of bituminons sand and its reactions with water and air are presented. It is not pretended that they are entirely correct, but it is believed that they lie not far from the truth. (1) Bituminons sand is an aggregate of sand, clay, oil, and water. The sand consists mainly of quartz particles of 100 ta 200 mesh size and smaller, but also of particles of other minerais including mica, rutile, ilmenite, tour-maline, zircon, spinel, garnet, pyrite, and lignite. Clay occurs interbedded with the bituminons sand, of which, also, it is a constituent. lronstone nodules of all sizes up to eight inches in diameter are likely to be present in the bituminons sand beds. The oil is viscous, naphthenic, and of a specific gravity slightly greater than that of water. The oil content ranges up to, and sometimes even exceeds, 17 per cent by weight. Rich bituminons sand from beds not invaded by water has a water content of 3 to 5 per cent by weight. The water is probably present as a film around the sand particles. The oil surrounds the moist sand grains as an envelope. (2) Water wets quartz and other siliceous minerals more readily than does mineral oil. Consequently, water tends to displace the oil film surrounding the quartz and other siliceous particles when the bituminons sand is mixed with water. Whether the oil is completely displaced depends on the properties of the water. That is to say, the materials dissolved or suspended in the water modify its wetting properties.

Jan 1, 1944

By Reno Pressacco

Abstract- Agrium Inc. is a world leader in the production, distribution, and marketing of agricultural products and services in both North America and Argentina. The new phosphate mine and mill complex located southwest of Kapuskasing, Ontario, was constructed to replace an offshore supply of phosphate rock, and produces a high-grade phosphate concentrate. The Cargill Township Carbonatite Complex is one of a series of carbonatite complexes in the region that are hosted by the 1.9 Ga aged Kapuskasing Structural Zone. The carbonatites in the mine area have intruded Archean gneissic granodiorite rocks of the Wawa Subprovince, and metasedimentary rocks of the Quetico Subprovince. The Cargill Carbonatite Complex displays a typical concentric zonation pattern from an outer ring of alkalic pyroxenites, through an inner ring of sövite-carbonatite, to a central core of rauhaugite-carbonatite. The initial carbonatite intrusion and subsequent residual orebody have been modified by faulting such that the northwestern third of the complex has been displaced approximately 2.5 km northeast. The phosphate ores are composed principally of residual apatite sands that were formed by the weathering and dissolution of the soluble minerals of the carbonatite protolith. These ores are subdivided by their iron content into high grade (A ores) and lower grade (B1 and B2) ores. They are separated from the primary unweathered carbonatite by a layer of saprolite, whose thickness varies depending upon the composition of the underlying carbonatite. Cretaceous waste materials consisting of well-sorted silica/kaolinite sand and peat deposits are typically found to stratigraphically overlie the ores. A minor amount of the ore feed comes from cemented phosphate ores. All rock types are covered by Pleistocene glacial tills and clays.

Jan 1, 2001

By P. Cain, B. Martens

"Grande Cache Coal (GCC), an investor-owned Alberta company, is in the final stages of the regulatory process leading to the resumption of coal mining in the Smoky River Coal Field of Alberta. Although many opportunities for low-cost, high-yield mining remained on the property, GCC opted for a long-term production plan that ensures stability for the local economy, sustainable use of the resources in the area, environmental responsibility and a satisfactory return for its investors.GCC entered the Alberta coal approval process in late 2000 with a public disclosure document. In October 2001, GCC formally submitted an application for mining approval and an environmental impact assessment (EIA) to the government and the public. The application covered the proposed Grande Cache Coal project, which includes the No. 7 underground mine, No. 8 surface mine and coal processing operations. The EIA provided a comprehensive investigation of environmental sensitivities in the project area, matched with environmental protection programs. The project is based on commencement of operations in late 2002. GCC’s plans are founded on a commitment to sustainable development and has framed this commitment in the context of a long-range mine development plan that will sustain the community of Grande Cache over the next 25 years. The Grande Cache coalfields offer extensive coal reserves and opportunities, for both surface and underground mining. Combining highly productive U.S.-style room and- pillar underground mining methods and conventional truck-and-shovel open pit mining, GCC’s approach to sustainable development encompasses community involvement and reclamation of mine sites to productive land uses after mining."

Jan 1, 2002

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961

By A. P. Craig

"I HAVE BEEN looking forward to addressing this particular audience about Trans-Canada Pipe Lines because you men, more than most, understand the problems of the pioneer. Trans-Canada Pipe Lines qualifies as a pioneer on two counts: it is certainly pioneering a completely new industry in Canada -the long-distance transmission of natural gas -and it has at least a few of the problems that are expected and normal to any pioneering venture.This morning, I’m going to try to give you a sketchy picture of our project and a brief report on its current status and our progress to date; and then a broad picture of Canadian markets for natural gas.The physical characteristics of the Trans-Canada Pipe Lines project have been discussed so often that I am not going to take the time today to quote a lot of statistics on pipe sizes, miles, tons of steel, etc. Suffice it to say that this project, estimated to cost approximately $350,000,000, will be the longest large-diameter gas pipe-line ever built anywhere.Let me try to paint a broad picture of this great national project, using only a few basic 'round' figures.First, it involves exploration for and development of the natural gas fields in Alberta and other provinces -the cost of which will run into hundreds of millions of dollars.Then comes the gathering, stripping, and cleaning of the gas before it can be delivered to Trans-Canada. This will cost close to $100 million.Next we have the Trans-Canada Pipe Lines project for transmission of the gas to Eastern markets -estimated to cost $350,000,000 during the first three to four years and making natural gas economically available to one-half the population of Canada."

Jan 1, 1955

By Paul D. Merica

This year of 1926 marks the 40th. anniversary of nickel mining in Canada. Although the first nickel mine of the Sudbury basin was discovered in 1883, it was not until 1886 that the Canadian Copper Company was organized and actually began to mine copper-nickel ore from the Lady McDonald, Stobie and Evans mines. The intervening years have witnessed some exceedingly interesting nickel history, particularly interesting and gratifying as well to Canadians. Forty years ago, at the inception of Canadian nickel mining, the world's consumption of that metal was about 1000 tons per annum and this was supplied largely from New Caledonia ores refined in France. This nickel was used principally for the production of nickel-silver, coinage alloys, and for nickel-plating. No processes were then known for refining the Sudbury ores nor for the separation of copper from nickel. Consequently, the pioneers in Canadian nickel mining faced the double problem of finding a method of treating their ores, and of finding a market for the nickel when and if they could extract it.

Jan 1, 1926

By A. H. C. A. Zimmerman

WE have just heard what must be regarded as a thoughtful, constructive and somewhat painful analysis of the financial function of our industry. While thinking about this, it is interesting to reflect on the conditions which have stunted the growth of the financial side of our affairs. Mining must be regarded as a wealthy business. •while immeasurable grub takes and development budgets have been lost, there can be little argument that a productive ore-body nearly always produces the type of wealth that breeds some extravagance. I recognize that this statement can be attacked from many sides, but an historical comparison with a commercial enterprise involving similar investment will demonstrate what I mean. However, these old times are be-ginning to disappear for a variety of reasons. High amongst these are: ( l) Increased costs of exploration. (2) Remoteness of many new finds. (3) Fixed or declining metal prices (particularly when expressed in constant dollars). ( 4) Constant demands for higher wages.

Jan 1, 1962

By K. Delbeke

Within the framework of the EU Existing Substance (93/793/EEC) and REACH regulations EC/1907/2006), the copper industry initiated in 2000 a comprehensive Voluntary Risk Assessment of copper and several copper compounds. The Italian Government's Istituto Superiore di Sanità, reviewed the process and reports on behalf of the European Commission. Copper exposure levels to man and the environment from production of copper anodes and cathodes, copper powders and copper chemicals as well as fabrication and use of semi-fabrication products and down stream user products were collected across Europe. Environmental and human health effects data were obtained from literature as well as novel research programs and used to deduct safe threshold

Jan 1, 2007

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By A. H. Winckers

"CAMIRO, The Canadian Mining Industry Research Organization, formerly known as MITEC, is a collaborative research organization of Canadian Mining Companies. It is comprised of Exploration, Metallurgical Processing and Mining Divisions.The Metallurgical Processing Division (MPD) has the mandate to contribute to the profitability, competitiveness, safety and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral processing and extractive metallurgy in an environmentally conscious manner through the development of innovative technology by managing cooperative industry focused research programs.Current membership includes about ten Canadian mining companies. Past research has largely focused on base metal mineral processing. The Division wants to expand its research base to include all areas of mineral processing and extractive metallurgy.Past performance and plans for the future will be highlighted in the presentation."

Jan 1, 1998

By Alice H. Zhu

Belt conveyors are widely used in materials handling industries. The bulk materials which can be transported include ores, coal, earth, grain, limestone, wood chips, fertilizer components such as potash and many others. Along with the new technology development and enhanced industrial automation requirements, belt conveyor instrumentation has also been modernized to improve conveyor availability and performance. Traditionally, belt conveyors are equipped with emergency pull cord switches to shut the conveyor down, misalignment switches to signal the belt offline condition, speed sensors to detect the belt slippage, and level switches to prevent material plugging in the discharge chute. Belt rip detectors are also normally provided for long belt conveyors. As a rule, equipment condition monitoring is not automated at most operating facilities, but is performed manually by maintenance staff via time-based surveillance. The new generation of condition monitoring instrumentation and control equipment can be successfully utilized to design a reliable, cost-effective, and centralized monitoring system, capable of monitoring a wide variety of mechanical equipment. The implementation of the condition monitoring automated system can provide continual monitoring of the plant equipment to ensure safe operation of the equipment to its required capacity. Any abnormal behavior of the motors, gear reducers and pulleys can be analyzed, alarmed, and recorded immediately, so problems can be detected and resolved before critical components failure. Therefore, the current trend is to provide the belt conveyors with condition monitoring system in addition to the traditional instrumentation, where temperature probes and vibration sensors can be installed on motors, gear reducers and all pulleys. Another innovative development is a three-in-one type belt rip detector which combines laser, tray and cord type detection together to ensure a prompt belt tear indication. The purpose of this paper is to present the latest development of belt conveyor instrumentation and introduce the application of newly developed instruments.

Nov 1, 2011

By Edith Lafontaine

Modern underground mines operate fleets of mobile production equipment including drill jumbos, long-hole drills, load-haul-dump machines, trucks and bolters. Their availability has a substantial impact onto production cost and thus onto mine profitability. Through appropriate collection of pertinent data and information, use of adequate performance measures and their analyses, mine operators can identify the most promising and cost effective opportunities to get more from their equipment and to reduce the overall cost. This paper presents results of the study aimed to review and analyse means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews current reporting procedures, sources, quality and quantity of the data and information collected as well as examines performance measures and their definitions used by the surveyed mines. Problems concerning data acquisition as well as meaningfulness and usefulness of the above mentioned metrics are also discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. It is believed that the latter may become a more useful tool for mine operators in their efforts to reduce production cost than it seems to be the case at present.

May 1, 2007

By Linda Dufour

"Autoclaves have been in commercial use in the mining industry since the early 1950's the initial applications included tin, uranium, cobalt, nickel and copper extraction under both acidic and alkaline conditions. These circuits varied in batch or continuous operation. The geometry has been spherical, vertical, and horizontal type with up to six agitators, with throughput as high as 1000 stpd.Presently autoclaves are a good process selection for many refractory sulphide gold bearing ores. The first application of pressure oxidation in the gold industry was at the Homestake Mcglaughlin's Mine which was commissioned in 1985. This was an acidic pressure oxidation process treating 3000 stpd in three four compartment horizontal autoclaves 14' diameter and 53' long. Since the initiation of autoclaves for the treatment of gold bearing sulphides, there are presently 16 gold autoclaves operating worldwide varying in size up to 18'4"" inside diameter. There are seven autoclaves for the treatment of refractory sulphide gold bearing ores to be commissioned in 1997 and 1998.Autoclave technology has progressed extensively since the mid-eighties. Operational experience has made rapid progress and the result is much smoother and safer autoclave operation. There have been many advances in autoclave technology design. For example, the use of exotic materials for corrosion resistance to reduce down time for maintenance. The instrumentation involved in autoclave operation is very sophisticated which allows for many safety features. The advanced design has allowed for greater availability and as a result operating costs and maintenance costs have decreased. These technological advancements have made autoclave technology more safe and this has resulted in a greater acceptance of this type of operation. Many of the gold autoclave facilities operate up to 9 months continuously without shutdowns. The advancement of autoclave technology has inspired many new applications.Because of the outstanding operation of autoclaves in the gold industry, many other applications for autoclave technology are being considered. The following is a list of autoclave applications:"

Jan 1, 1997

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By K. N. Subramanian

Previously reported work on total oxidative leaching of chalcopyrite concentrates ha s shown that high copper extractions are obtained at 210°C and 0.4 MPa oxygen pressure. A simple integrated flow sheet using pressure leaching, solution treatment involving precipitation with a calcium base, and electrowinning to produce wire-bar-quality copper is described. Reagent and energy requirements developed from this work indicate that the process could be attractive for small operations where a smelting-refining complex cannot be justified.

Jan 1, 1978

By Denis Labrie

Résumé Cent soixante (160) câbles d'ancrage ont été installés au toit de la rampe à la Mine-laboratoire de CANMET à Val-d'Or, Qué bec, Canada, pour prévenir toute dégradation suite à l'élargissement de la voie de roulage dans un secteur tournant à 180 degrés, communément appelé Virage Santa Barbara. Le roc à cet endroit est de nature bloqueuse et stratifiée, et son épaisseur au toit de la rampe est limitée à environ dix (10) mètres, le tout sous une couche de terrain meuble saturée en permanence. Le soutènement mis en place a été conçu pour former une zone de compression et supporter une strate de roc d?environ quatre (4) mètres d'épaisseur. Les critères de conception et les méthodes d'installation sont présentées. Un contrôle de qualité rigoureux a été effectué au moment de la mise en place du support, notamment en ce qui concerne la mise en tension des câbles eux-mêmes et la qualité du béton utilisé lors de l'injection. Des instruments de mesure seront mis en place sous peu pour dépister tout mouvement éventuel au toit de la rampe. Abstract Design and installation of an active mine ground support using tensioned cables at the Experimental Mine, Val-d?Or, Québec, Canada. One hundred sixty (160) cables were installed at the back of the ramp at the CANMET?s Experimental Mine located in Val-d?Or, Québec, Canada, to prevent any degradation of the ground after the enlargement of the roadway in a sector turning at 180 degrees, usually called Virage Santa Barbara. The nature of the rock mass in this area is blocky and stratified, and its thickness above the ramp does not exceed ten (10) metres. Eight (8) metres of soil, mostly saturated, cover the bedrock on top of the ramp. The ground support was designed to form a compression zone at the back, aimed to carry a strata of rock of around four (4) metres thick. The design criteria and the methods of installation of the ground support are described in the paper. A strict control of the quality of the grout used for injection and the tension placed in the cables was carried out during the installation of the support. Ground monitors will be installed soon, to detect any movement that could take place above the ramp.

May 1, 2001

By I. H. Warren, Forward F. A

The reduction of aqueous slurries of uranyl carbonate at elevated temperature with compressed hydrogen m the presence of metal catalysts and certain organic promoters has been shown. to yield uranium dioxide. The reduction takes place in a sequence of steps. The purity and sintering properties of the dioxide make it of interest as a starting material for fuel element production. Simple control can be exercised over the surface area and oxygen/uranium ratio of the product during reduction. URANIUM dioxide for fueling atomic power reactors 1s conventionally produced as a powder by simultaneously decomposing and reducing ammonium diuranate with hydrogen in a furnace at high temperature. Fuel elements are then generally made from this powder by compacting and sintering ( 1). In order that elements approaching theoretical density may be obtained,

Jan 1, 1961