Search Documents

In process industries, time-dependent random fluctuations of raw material characteristics and mass flow rates in bulk material or pulp flows cannot be always prevented for different reasons, eg because of the geological situation (no uniform formation of the deposit) or/and because of technological reasons (segregation in bunkers or on stockpiles). Since a long time, there has been practical experiences that such fluctuations can have negative consequences, eg: ò fluctuations of the final products characteristics, ò higher expenditure for process control, and ò worsening of technological characteristics (recovery, sharpness of separation etc). In the literature, there can be found a lot of details as to, eg the improvement of the sharpness of separation in a jig in dependence on the raw material blending (Kubitza, 1981; Gathen, 1983) or the decreasing flotation recovery with increasing raw material characteristics fluctuations in iron and potash ore processing plants (Bubnova, 1978). Up to now, however, these consequences of random fluctuations, eg on the separation efficiency were not predictable theoretically. It could be shown by means of the general model for mechanical macroprocesses (Graichen, 1989), that the reduction of input fluctuations passing a blending facility can be calculated in this way. In this example, the steady state of the process is the wanted one, but, in general, the model is able to describe also non-steady states of the process regarded. On the other hand, the general model of mechanical macroprocesses has been used successfully for modelling separation processes, eg cross-flow and air classification (Molerus, 1969; Neesse, 1991; Senden, 1979; Tichonov, 1973). That is why it was tried to model the influence of input fluctuations on the separation efficiency, that means, the impact of non-steady states - as a consequence of random fluctuations - on a separation process. The models discussed in the literature are related nearly exclusive to the steady state of the process. The reasons for that lie in the (relative) simplicity of the models and the fact that the steady state is aimed at by means of blending processes under practical conditions - because of the advantages mentioned above. These models cited have proved to be superior to other models, since the basic general model for mechanical macropocesses makes possible the consideration of turbulence acting in the process unit and influencing the separation process essentially. This is valid also for modelling the turbulent cross flow classification, applied to mechanical classifiers and hydrocyclones, where the correspondence between the separation characteristics (cut size, separation sharpness) calculated and determined experimentally is much better than for other models.

Jan 1, 1993

By Adeloju S, McQuade CV, Riley SJ

Metal contamination of sediments can be an issue for minesites discharging water. Water sampling of receiving waters is frequently undertaken. Sampling and analysis of sediment is less common. The variability of receiving environments makes the formulation of a generic sediment sampling strategy virtually impossible. Each situation needs to be carefully assessed before sampling is undertaken. This paper outlines the approach taken for one such survey.The main factors that need to be considered in a survey of surficial sediments are sample representativeness and sample variability. A simple data set from one site within a regional survey is used to illustrate the importance of these factors. The metal content of sediment is shown to vary significantly over small spatial scales.The variability associated with the spatial distribution of samples within a site is shown to be the most significant source of variability in the study. This variability could bias the results of a study if not planned for in the sampling methodology. Taking multiple samples from within each site (sub-site samples) and combining the data gives a more representative indicator of overall conditions than a single sample. The optimum number of sub-site samples to be taken from each sampling site was found to be 15.It is shown that a composite of sub-site samples can give a good indication of the average site metal content, while considerably reducing the sample preparation and analysis effort.

Jan 1, 1998

By D Morrison, P Goodman

The cycle time between adjacent stopes is critical to achieving the required production rate from 3500 Orebody; one of the Enterprise Mine orebodies. Current Mt Isa cemented fills require a 90-day cure period which had to be cut to 30 days while maintaining the required strength criteria. The Enterprise Mine Feasibility Study recommended that this be achieved by Cemented Slurry Rock Fill (CSRF), but that on-going research into paste fill be continued. The continuation of the research, in conjunction with overseas visits has recommended that the 3500 Orebody be filled with paste fill, with the potential to fill other orebodies. The paste fill will comprise cyclone and thickener dewatered copper tailings to which Portland Cement (PC) is added before vertical borehole delivery and undergound pipeline reticulation to individual stopes. The benefit is not only re-use of copper tailings but also much reduced binder usage.

Jan 1, 1998

By B F. J Kelly

Multiple-point simulation is a family of methods used to generate conditional facies simulations that present the same spatial dependence as a user-defined training image. The main advantage of using a training image is the easy integration of geological concepts in numerical subsurface models. The strength of multiple-point methods is that it allows making the best use of geological expertise when data are too sparse for inferring a model of spatial continuity. However, despite being appealing to geologists, the multiple-point methods are often not used in practice due to the difficulty of building complex 3D training images that contain realistic features.A new framework for multiple-point simulation is presented that involves small and simple training images. The main idea is to use random transformations to expand the range of structures available in the simple training image. The training image is not regarded any more as a global conceptual geological model, but rather a basic structural element of the subsurface. Complex geological structures are obtained, whose spatial structure can be parameterised by adjusting the statistics of the random transformations, based on field data or geological context. In most cases, such parameterisation is possible by adjusting two numbers only. One advantage is that the training images are so simple that they can be easily built even in 3D. The method allows building 3D models that reproduce shapes corresponding to a desired prior geological concept and are in phase with different types of field observations, such as orientation, facies or geophysical measurements. The flexibility of the approach allows for naturally integrating different types of data. This is demonstrated on an example involving seismic data assimilation. Examples where complex 3D folded structures are built from a simple training image and a few orientation data are shown.

Sep 26, 2011

Qualitative measurement of respirable dust in metal mines is limited and an example of this is demonstrated at Northparkes Mine, where operational experience was sought for measuring dust standards and identifying exposure limits. However, relying on operational experience has limited value due to variation in observations from person to person and is based on visible dust (which is larger in size than respirable dust). However, with sophisticated dust measuring equipment, like the real-time aerosol monitor, dust concentrations can be accurately measured and recorded concisely. Research conducted as part of a collaborative agreement on behalf of Northparkes to launch an occupational dust monitoring program was implemented on the mine site. To form the basis of this research, it was hypothesised that no proper dust measuring testing at the mine site had been adequately identified. In addition, existing occupational hygiene monitoring programs did not adequately quantify employee exposures to these hazards. This project will outline the results of an occupational dust monitoring program, hence greatly improving the capacity to quantify the health risks posed to employees.

Jan 1, 2008

By Whiten W. J

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. In this way model parameters are obtained describing the behaviour of ball mills over a wide range of mill sizes and operating conditions. These parameters define the flow and breakage of each size fraction of ore in the mill. Flow of coarse particles through the mill is found to depend on the proportion of coarse particles present. The breakage rates of coarse particles are found to decrease markedly with mill diameter for mills over 3 m in diameter.Simulation of grinding circuit throughput at constant productsizing for different mill diameters shows that throughput is proportional to theoretical mill power consumption for mills up to about 3 m in diameter. Thereafter the throughput gradually falls below that indicated by power consumption, the decrease becoming quite significant for large diameter mills. Simple qualitative physical arguments are presented to explain this behaviour. The models developed have applications to ball mill scale up. Work on their further development is continuing.

Jan 1, 1982

By James D

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Ltd has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the west coast of the -South Island, New Zealand.The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilizing spiral, wet magnet, high tension and plate electrostatic separators have been G47designed to produce ilmenite from the ore. Studies to utilize the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

By McNicol J. H

Using a small scale laboratory pilot plant a series of tests have been conducted with the aim of investigating the influence of the zinc/acid ratio on the efficiency of zinc electrodeposition from an acidic sulphate solution. The results have shown that current efficiency is increased as the zinc/acid ratio is increased with no evidence of an optimum zinc/acid ratio. However the choice of a zinc/acid ratio for full scale operations must be a compromise between other parameters, spent electrolyte acidity and power efficiency, which also impact upon plant performance. The effect of various impurities has also been monitored and antimony, nickel and tin have been shown to be deliterious to current efficiency.

Jan 1, 1989

By Geoff Baldwin

The use of monitors to assess equipment performance is carried out on a routine basis in many industries. The benefits gained through process control in knowing exactly how the equipment is working far outweigh the initial capital costs of the monitor. In the mining industry several dragline monitors have been developed and installed on equipment through out the world, but to date none has been fully accepted by the industry. This paper describes the use of a sophisticated monitoring system which incorporates an onboard processor to assess both dragline and blast performance. The results of a case study are presented and an indication of the potential of the monitoring system to optimise mine production is given.

Jan 1, 1990

By West Coast Staff

Attention to the design of facilities for drainage, of both surface water and seepage, made it possible to attain, for a qam impounding residues from a concentrating mill, a more stable sand wall which can eventually be carried to a greater height.EXPERIENCE WITH No. 1 DAMResidue from the lead zinc concentrating mill, which treats the ore from the Rosebery and Hercules Mines, was pumped 3,600 ft. through a 5-in. diameter woodstave pipeline to the site of the dam. It was formerly delivered through a 4-in. steel pipeline.State laws prevent the residue being discharged to waste into the Stitt River. Furthermore, as a pyritic residue it is a potential source of sulphur.Between 1936 and 1956 more than 1,000,000 tons. of residue was paddocked. The run-of-mill product was roughly classified at the dam in a 6-ft. diameter cone classifier and the sand fraction was pumped by a 3-in. pump to the front wall of the dam across a shallow valley. The overflow gravitated to the rear of the dam (Fig. 1). Typical sizings were:

Jan 1, 1958

This paper reviews factors involved in the feasibility stage of underground mine project development. Emphasis is placed on the need to first select the best method of extraction and make the most accurate assessment of the expected output even with the uncertainties which may exist in structural interpretation, ground stress, geotechnical factors, and industrial conditions. The subsequent engineering planning should be undertaken from the point of view of the face requirements and is subject to constraints imposed by the method of work and nature of the deposit and, in the case of access, to surface constraints and services.

Jan 1, 1983

By Teague JK, Read HW

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years. Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the Illawarra Measures of the Southern Coalfield of New South Wales were carried out. The optimum range of vitrinite was found to lie between 45% and 60% (mineral matter free). Above and below this vitrinite range coke strength deteriorated. I Coke strength indices increased with rank and the optimum vitrinite content increased with an increase in rank. These changes will require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal. . T Use of- petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved. Significantly more work is required before coal reserves can be utilised to optimum advantage. This work would require extension of-the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1970

The mineral resource that a mining company has access to, represents the majority of the embedded value that exists within the company, as well as the competitive advantage that the company has over its peers. However, the real value is only realised once effective mining plans have been put in place, which optimise the extraction of the resource, and add measurable value to the company. The concept of mineral resource management (MRM) has been developed in South Africa, to ensure this optimisation happens in an integrated and quantifiable manner, such that value is added and risk is reduced, resulting in bottom line improvement for the stakeholders of the business. This paper describes the process of mineral resource management, and draws on successes and failures of various companies, to illustrate how it should be implemented, and what measures should be put in place to ensure its success. This requires a fundamental re-appraisal of the way in which mining companies plan and execute their businesses, and focuses attention on real value adding activities and behaviour through the use of economic value added as an appropriate metric by which to measure real value and risk. Specifically, the paper focuses on these aspects as applied to planning models and processes, exploration activity and risk management, to ensure operational and project success.

Jan 1, 2006

I must tell you at the outset that I come to this conference deeply disturbed at the `role of Government in international dealings in mineral and energy resources'. I am disturbed by the confusion that now passes for policy. I am disturbed by the short- range view of critical problems taken by a majority of Governments. I am equally disturbed by the even shorter range of view taken by a growing army of industries. Many of them clamour for Governments to solve their problems in a specific way, with little regard for any other sector but their own-and with even less regard for the fact that every time a Government takes over some of their responsibilities they surrender some of their freedom. I would not say that longer range views don't exist. But I would say that they don't prevail at the present time. Instead, we are seeing the con- stant development of many policies for individual problems which don't tackle the fundamental causes. We must get back to basics without delay.

Jan 1, 1978

By S Vink, V Nanjappa, C J. Moran

Poor quality water resulting from interaction of surface run-off with saline mine spoil and soils can cause significant problems for water reuse on mine sites. Not only can this saline water lead to machine corrosion and increased maintenance costs, but may cause detrimental effects on the environment. Determining the geochemistry of mine spoil, and the likelihood of salt dissolution during rainfall events, may aid in more effective mine site management of water. Spoil samples were taken from three areas of the German Creek mine site, situated in the Bowen Basin coalfield, Queensland. Samples from two undisturbed areas on the lease were also collected for comparison. Analyses were performed using a variety of laboratory techniques: leaching tests, effective cation exchange capacity determination, X-ray diffraction, clay quantification, and total organic content determination. Results show that dissolution of surface (top 2 cm) salt minerals from spoil areas is an important contributor to surface run-off salinity during rainfall events. Equally, ion exchange with clay minerals appears to be a significant source of elevated ion concentrations in run-off waters. Findings from the undisturbed areas show undetectable quantities of salt mineral species, resulting in waters with low ion concentrations. More generally, monovalent cations (sodium, and to a lesser extent potassium) appear to be derived from dissolution of salt precipitated whereas divalent cations (calcium, magnesium) are more likely to be sourced from exchange reactions with clay minerals. Incorporating knowledge about the mechanism of cation mobilisation from spoil with the spatial distribution of spoil properties and understanding of the dynamics of water quality variations on the site will aid in development of integrated water quantity and quality management strategies.

Jan 1, 2009

Seven papers included in Session 8 of the Third International Mine Water Congress under the heading "Achievements in Mine Water Management & Research" have been reviewed. Only one paper, a case study by Masters on biological treatment of inorganically polluted effluent, has any connection with research in the sense of seeking new, generally applicable knowledge which would advance the frontiers of mine water management. The remainder deal with various aspects of the management of mine water ranging from investigation of the geology of a specific aquifer system through operating dewatering systems to the management of specific effluent disposal problems.

Jan 1, 1988

The treatment of slimes has of late years been the chief difficulty in connection with cyanide work, in which much time and money has been spent in endeavouring to find a practical solution of this problem.The processes at present in use are:-1. Filter pressing, as practised in Western Australia.2. Decantation, as practised in South Africa.Filter pressing after apitation affords a ready and efficient means of separating the gold bearing solution from the slimes and admits a perfect washing thus ensuring a high extraction but the very high working costs forbids its application except on high grade material, the chief items being the necessary large amount of labour, compressed air, and general upkeep, none of which can be materially reduced. The decantation method has the ad vantage of low working cost but on the other hand the low extraction obtained, due to imperfect washing, the length of time occupied in' the treatment, and the enormous bulk of solutions to be handled, are serious disadvantages.In either process it is absolutely necessary to obtain a perfectly clean solution before starting the gold precipitation by zinc, which is a source of much trouble. Also the high first cost of installing either plant is such that they can only be adopted on mines with very large working capital.

Jan 1, 1903

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

By McDonald E, Clifford PJ

A mine planning system comprises all elements necessary to carry out the full range of mine planning activities from exploration to operations control. The application of computers as part of a mine planning system has great potential for increasing the efficiency and quality of mine planning and reducing its cost. The introduction of computers to mine planning in open cut coal mines has been hindered by the cost of processing the large databases associated with large coal deposits and the inherent inconvenience of performing an interactive process on a time-shared computer. A dedicated computer is ideally suited for the purpose but reasonably priced micro/ mini-computers until recently have not had the capacity to store the volume of data or the processing capability required. Recent hardware developments have cleared the way for the development of truly interactive mine planning software, covering the complete range of activities associated with open cut coal mine planning, incorporating them into a single system using a common database. The MINEMAP System is a hardware and software package tailored specifically for mine planning of open cut coal mines and is an example of such a system.

Jan 1, 1983

It is important to prevent the overload ing of mills being operated near maximum tonnage. Changes occurring during overload differ in their usefulness as guides to control action. The Primary Ball Mills of Bougainville Copper Ltd. provide an example of some of the problems and progess in avoiding overload.

Jan 1, 1978