Search Documents

By Vassiliev P

Cut-off optimisation, based on the work of Lane (1988), can be used to maximise the NPV (Net Present Value) of a mine by the judicious manipulation of cut-offs and the use of stockpiles. Apart from maximising NPV, cut-off optimisation will ver

Jan 1, 1998

By S F. Simmons, A McOnie, J L. Mauk

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water whereas the mineral assemblage of replacement calcite-interstratified illite û montmorillonite-kaolinite forms a carapace and reflects formation from a CO2-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

By B Wiggins, M Russell

Off-gas handling systems are a critical component of modern metallurgical furnaces and typically represent as much as 50 per cent of the total installed smelter capital cost. Inadequate off-gas system performance, due to insufficient exhaust flow or excess maintenance downtime, can present a serious process bottleneck and limit smelter production rate. Therefore, it is essential that the relevant performance issues are fully understood and considered in the design of these systems, particularly when combustibles produced within the furnace must be combusted or handled in the off-gas system. This paper examines the requirements, design issues, and conceptual design process for state-of-the-art postcombustion off-gas systems. The relevant design considerations of safety, environment, energy consumption, and maintenance are presented, and the relative importance of these key issues are compared and discussed. The benefits of using computational fluid dynamic (CFD) modeling in the design process at the conceptual design stage are also demonstrated. Finally, the design basis and performance of a recent Hatch-engineered system currently in operation is evaluated.

Jan 1, 2002

By Hayes K. M, Ostwald J

Compacted tablets of hematite ore (containing clay and quartz gangue) and limestone were heated in air in an ULVAC-RIKO rapid heating furnace to maximum temperatures in the range 1200-1350°C.The resulting sintered products were examined in terms of mineralogy, texture, strength and reducibility. The sintered tablets are a good analogue of normal plant sinters. These investigations have shown that sinters of optimum reducibility are produced in the narrow temperature range 1250-l275°C. Conditions for the production of such highly reducible sinters under plant conditions are discussed.

Jan 1, 1984

This paper presents the water management plan of the Mae Moh Project in the North of Thailand, which includes a large lignite opencast mine and thermal power plants. Lignite production will increase from the present 5.5 million tons per annum to approximately 20 million tons per annum by 1995 when the pit area will be about 20 sq.km. and the depth at over 300 meters. Seven power plants are proposed of which two are under construction. The total capacity to be installed is 2,925 MW. The principles considered for water management are firstly flood protection, including drainage of the mining pit and diversion of the Mae Moh stream away from proposed future mining areas; and secondly, a plan to meet the water requirement of the thermal power plants, while maintaining downstream supplies for irrigation and other purposes. The limited annual run-off of Mae Moh and Mae Chang watershed basins are inadequate for the proposed power plants. A study has been prepared to compare two approaches, namely conveying water from remote watersheds to meet the water requirement of the power plants up to total installed capacity; or by limiting future total generation, at the existing site, to only 2025 MV.

Jan 1, 1988

By A Williamson

The New South Wales Department of Mineral Resources objective is to use data and information to undertake a detailed analysis of incidents and accidents to identify risks so that the predictable can be foreseen and avoided. The Department of Mineral Resources has established a computerised database called COMET (COmmon Mines EnvironmenT) to capture information on accidents incidents, inspections, audits and accreditation in improving safety and environment performance. This data together with data from Coal Mines Insurance and WorkCover NSW is being used to provide trend and comparison information. The NSW Injury Risk Management Research Centre at the University of NSW has been engaged by the Department to collate and prepare a detailed analysis of the data. Through this process, five areas have been identified for further research. These being: electrical energy, mechanical equipment, work environment, hours of work, and contractors involvement accident and incidents. The paper covers: the establishment of a mix of performance measures for the industry to indicate whether the safety performance is improving; the provision of data to provide useful comparisons and benchmarks against which companies can compare performance; the development of positive performance measures; the findings and outcomes of the detailed analysis of electrical energy; shocks; the provision of information to industry; an outline how the data is being used to determine departmental; operational priorities; and future plans to undertake research into the other areas identified.

Jan 1, 2003

By J-H Shin, Y-S Jung, D-J Youn, G-J Bae

This research is to grope for a method to reduce high pore pressure taking place on tunnel shotcrete lining, especially in underwater tunnels, effectively by utilising a new concept of patternised pin drain. Accordingly, the patternised pin drain system is investigated numerically in order to confirm to the effect of reduction of pore pressure by the pin drain and its effective application. Installation of pin drain shows considerable reduction in the figure of pore pressure. It is found through 2D numerical modelling that the change of pore pressure, according to the shape and the location of pin drain, is sensitive by the sequences of the change of location > the change of length > the change of angle degree. In the results of investigation in 3D modelling, the pore pressure is the largest in the centre of the interval among pin drains, and it is possible to obtain an ideal degree of longitudinal angle and an interval by investigating pore pressure taking place on the lining.

Jan 1, 2008

By M A. Gontalves, A F. D C Varajpo, S A. Stachissini

Clays from the Santa Elena Peninsula, south-east of the Ecuador coast, were investigated with a view to identifying their main mineralogical, physical, chemical and textural characteristics as well as their potential for industrial use as adsorbents. Identified as calcic bentonites, two representative samples from the Tosagua Formation (Oligocene to Lower Miocene) were selected for acid activation trials. The selection criterion was based on the greatest amount of clay fraction (<2 ¦m fraction) associated with the greatest content of montmorillonite. For the activation treatments, HCl and H2SO4 solutions of 4, 6 and 8 N were used in a stirred glass reaction vessel with the clay sample under reflux during four hours at temperatures of 70¦C for HCl and 85¦C for H2SO4. Mineralogical analysis by X-ray diffraction (XRD), chemical analysis by X-ray fluorescence (XRF), differential and gravimetric thermal analysis and measures of density, surface area and porosity indicated the changes occurred in the crystal structure of the montmorillonite. The acid treated clays were utilised in trials of purification and decolourisation of soybean vegetable oil in a ratio of 2:100 (clay/oil) at 90¦C for 30 min, under constant stirring. After centrifugation of the suspension, the wavelength of the bleached oil was measured by UV-visible spectrophotometer and the bleaching capacity of the clays was determined. The best bleaching capacity of the samples was obtained with 6 N H2SO4 acid-activated clays. The bleaching capacity was compared to Tonsil, a commercial acid-activated clay and similar results between them evidenced the potential industrial application of the Ecuadorian clays to bleaching of vegetable oil.

Jan 1, 2008

By Ren T. X, Jozefowicz R

In many branches of engineering, there has to be an understanding of the motion of fluids in order to solve problems. Many safety and health problems in the mining industry are typical examples that involve the understanding and analysis of fluid flow, such as explosions, the spread of fires, dispersion of gas and dust, and ventilation patterns. Computational Fluid Dynamics (CFD) is concerned with the use of computers to produce information about the ways in which fluids flow in given situations. Until recently CFD has been widely applied to a variety of industrial sectors and increasingly to problems in the health and safety areas. With the arrival of more powerful computers and CFD packages, CFD techniques are no longer practised solely in a research environment, but can be used by engineers in many industrial fields. This paper introduces the basic concepts and general procedures involved in the use of CFD technology. A comparison is given as a guide to the major features of a number of widely used commercial CFD codes. Areas of potential CFD applications are identified in a range of safety and health problems in mining industry. An example is presented to illustrate the use of this technology. It is believed that the exploitation of these areas using CFD approach will contribute significantly to the solution of today's many mine health and safety problems.

Jan 1, 1995

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By Fee BS

This paper describes four new families of collector products which are currently being introduced at the industrial level. A brief summary of the chemical basis behind each product family will be given. This is then followed by a selection of flotation examples which illustrate the more important use characteristics that have been observed to date. It is becoming more apparent with further testing that these four new product families can offer both technical and economic advantages to the industrial flotation process operator.

Jan 1, 1993

Nickel-iron sulphide mineralization at Nepean, Western Australia occurs within a small Archaean greenstone outlier in granite south of the main Coolgardie greenstone belt. Individual sulphide ore bodies are situated near the foot- wall contact of simply-differentiated en echelon ultramafic sills that have intruded a sequence of sulphide-bearing metasediments and amphibo- lites. The paper describes a detailed section through the No. 2 ultramafic sill and its associated sulphide ore zone, which gave Metals Exploration N.L. the first significant nickel discovery in the Nepean area in 1968. The sill is variable in thickness up to 30 m along a strike length of 600 m, and is truncated to the north by pegmatite intrusion and pinches out to the south. The body has border zones of pyroxenetic composition, now represented by felted aggregates of chlorite and amphibole, and a central peridotitic core in which olivine and orthopyroxene are concentrated towards the base. Textures within the peridotite are dominated by large lath-shaped olivine grains and their serpentine pseudomorphs, which delineate triangular areas composed of talc, chlorite, and amphibole. Orthopyroxene occurs in large ovoid patches and is often replaced by Talc.

Jan 1, 1973

By M Tessier, M Pahkala, L Sletmoe

The Red Lake mine is one of the richest gold mines in the world. The primary mining methods are overhand and underhand cut and fill. Starting in 2003, Goldcorp initiated an expansion program at the mine. The expansion includes a new 6.55 m diameter hoisting shaft currently under construction. The shaft will be driven to a length of over 2180 m. The shaft will be used as a primary ventilation intake to the mine. In addition to the new hoisting shaft, a return air raise is being driven approximately 1690 m from surface. This raise will be a parallel return to the existing mine infrastructure. This paper describes the ventilation and climatic analyses performed in support of the expansion project. The study included a full mine ventilation survey, in situ rock mass measurements, analysing options related to mine layout, airway sizing calculations, air heating options, and climatic simulations. Specifications were prepared for an air heating system and main and booster fans. Analyses were also performed related to heat in the stoping areas namely caused by auxiliary fans and backfill with high cement content.

Jan 1, 2005

By Ulvelin K, Antila K

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By Fermino R

Reduction of waste oxides from steel plant operations was investigated in a laboratory tube furnace at different temperatures and furnace atmospheres. The results have shown that the waste oxide pellets are reduced rapidly to very high degrees of metallization irrespective of the furnace atmosphere and that the reduction is simultaneously accompanied by significant low- ering of the original impurities. It is shown, for example, that treatment at 1000¦C for 30 min. can reduce the Zn content from 0.98% to 0.0065% and K and Na contents from 0.19% and 0.76% respectively, to less than 0.01%. However, pellet strength at 1000¦C was low but this, as shown in the paper, can be very significantly improved by treatment at 1250¦C. The results indicate that the reduction of the waste oxide pellets of this investigation proceeds almost certainly by a chain reaction mechanism and that this principle could be advantageously extended to the reduction of iron ores and other oxides in general.

Jan 1, 1984

By Tronson K

Improvements in technology do not necessarily lead to higher profits: the benefit of lower costs can be captured by coal buyers, governments and workforce rather than by the colliery operators. The economic impact of longwall mining in Australia has been critically assessed to provide lessons for the future. For a variety of reasons, companies investing in longwall equipment in the past five years have generally not achieved an adequate return on the funds invested. The effect of technological innovation must be examined in the light of competitive forces operating in the market. Projections of cost reduction trends in the coal industry have been applied to a world cost model to provide a picture of the coal industry in the year 2000.

Jan 1, 1988

Blasting is known to be both an important and an easily quantified cost factor in rock breaking operations. However, the indirect costs and benefits of the blasting operation are not easily determined due to the irreversibility of the mechanisms involved and the multiplicity of influencing factors. A general conceptual model showing the relationship between blasting and mining costs is well known, but serious attempts to address the critical real relationships have all floundered on the fact that not enough is yet known about either detonation physics or blasting effects. This can only be remedied to the extent that blasting instrumentation enables researchers to pin down not only the relationship between the detonation process and its impact on a particular environment, but also the downhill costs of handling the rock, repairing any damage and building in "Safety Factors" to provide for imponderables. It is vital to standaraize on specifications for instrumentation and measurement techniques and there is a need to review what has been achieved in blasting expertise so as to focus on the most fruitful paths for future work.

Jan 1, 1990

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

By L Reynolds, N Whetter, S C. Cox

The Reefton Goldfield has had the largest hard-rock gold production (64 t Au) on the West Coast of the South Island of New Zealand, and is currently under renewed development by Oceana Gold. The gold predominantly occurs in variably sheared quartz veins that are associated with zones of tighter, shorter wavelength folds in the host Greenland Group metasediments. The quartz veins typically occur as a series of plunging shoots that align with specific fold limbs or fold hinge zones. Shear zones containing disseminated mineralisation and quartz veins have thickness variations that relate to the angular relationship between the shear and host-rock bedding. Exploration strategies and targeting can be developed around both types of structural control.

Jan 1, 2005

Nickel laterite approximately 40% of the remainder caning deposits. ores are the source of the world's nickel with from sulphide ore Although laterite ores are near the surface and cheap to mine they require significantly more energy to treat than sulphide ores. The escalation of oil prices comiencing in 1973 meant that nickel laterite refineries using oil as an energy source were placed at distinct disadvantage relative to sulphide refineries or those with coal derived energy. The Queensland Nickel refinery commenced a construction programme; in 1980 to allow ore drying and power generation to be converted from oil to coal. Since late 1981 ore drying has been undertaken using heated air from two moving grate spreader grate stokers. The changeover from oil to coal drying proceeded without process disruptions. This paper discusses the plant changes required to allow the receipt of coal and the operating performance obtained from the coal fired air heaters.

Jan 1, 1987