Search Documents

By J J. Jiang, M Reimnitz

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is mining through a dense network of disused level workings and open stopes of greatly varying sizes. The condition of the stope crowns and remnants is often unknown, and ultimately these structures become a significant proportion of the production floor and pit walls. Significant seismic events and occasionally rock bursts often occur in the underground workings. Seismicity is becoming an issue to the viability of the KCGM Fimiston operations. KCGM needs to take a leading role in understanding mine-induced and regional seismicity. The seismic system trials were initiated in the Fimiston Open Pit in 1996 using the ISS system. The initial system included two triaxial geophone arrays and two triaxial accelerometer arrays installed into two boreholes. The main objectives of the trial were to investigate the suitability of the two types of sensors and the detectability of seismicity in the pit. The trial was regarded as a success and the system has been expanded and improved. The current system consists of 12 triaxial geophone and accelerometer arrays and nine uniaxial geophones. The 12 triaxial arrays are installed in nine boreholes drilled from the pit and the nine uniaxial geophones are installed from underground level workings about 660 m below the original surface elevation. The system is designed to provide seismicity coverage for the entire pit area that is about 2.7 kilometres long, 1.5 kilometres wide and about 300 metres deep. The accuracy of the source location has always been a challenge due to the existence of the dense concentration of stopes and lack of the sensors. It is uncommon to have direct ray path for the seismic waves to propagate to the sensors across the strike, hence sensors have been located along strike and under the old workings. This paper discusses some of the challenges associated with seismic monitoring near mine remnants and seismically active faults. The results of the seismic monitoring are presented, and contrasted to results of three dimensional boundary element numerical modelling. The impact of the seismicity upon pit slope stability is briefly discussed.

Jan 1, 2003

By Y S. M Tabatabaei, R Hosseini Tabata

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulfide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A ferrooxidans was used to change the surface chemistry of pyrite and copper sulfide ores and consequently, their flotation behaviour. In the presence of A ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulfide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria could be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50 per cent lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

At the Nikkel og Olivin nickel mine near Narvik, Norway, Outokumpu has been the operator since 1993. The mine was opened in 1989 and in 1992 Outokumpu commenced operations to secure concentrate deliveries to Harjavalta's nickel smelter in Finland. Annual production is about 740 000 tonnes of nickel ore grading 0.5 per cent Ni, about 25 000 tonnes of nickel concentrate and about 2800 tonnes of nickel metal. All production comes from underground operations which makes Nikkel og Olivin AS perhaps the lowest grade underground nickel mine in the world today. Production is currently from one of two orebodies, which is known as the Western orebody. The Eastern orebody was worked out by 1995. During Outokumpu's operational period the Western orebody has been delineated and taken to production. The underground exploration and definition drilling involved about 15 000 in of diamond drilling, which was carried out during a nine-month period. Following this a feasibility study was undertaken and production commenced. Improvements were made to the mining methods. Previously the mine utilised open pit equipment underground and this resulted in an enormous amount of additional tunnelling. Grade control and ore delineation were previously based on sparse diamond drilling and all geological information was processed manually. The improvements included the use of underground sludge drilling to increase the amount of geological information, the of a new computer system for grade control and mine planning, new automated underground longhole drilling equipment and the of underground mining equipment which reduced the size of the drives. These changes produced a marked increase in the efficiency of the underground Mine.

Jan 1, 1996

Most of the gold reef mined today in South Africa is approximately 1 m in width with slopes about 30 m long. To prevent production interruptions it is essential that the stopes should not be blasted in sections. The shortage of experienced labour and arduous working conditions at the face dictate the need for simple blasting techniques.Hence, a pyrotechnic blasting system of sequential firing is in use at present, although research work to improve this technique is in progress.

Jan 1, 1985

By G Johnson, S Michalek, N Redman

As the modification of the 2009 Mill OperatorsÆ Conference theme from æmilling through the boomÆ to æthe boom û experience gained and lessons learnedÆ exemplifies, comminution practitioners are facing a series of challenges in the dramatically changing mining environment. One of the main problems plant managers have been facing during the boom times has been the severe metallurgy skills shortage and high staff turnover, both factors that can cause difficulties in mill liner management. Many of todayÆs mill managers are now also more than ever faced with the need for cost-cutting in order to continue operating viably. Amongst other potential target outcomes such as maximised throughput, MillMapperÖ, a tool for mill condition monitoring and mill performance optimisation, can be utilised to address these issues. This paper demonstrates how MillMapperÆs quantifying decision making tools can serve to be in control of managing mill liner and production issues, and how it can form the basis for mill cost savings without the risks normally associated with conventional methods or the lack of using any condition monitoring methods. MillMapperÖ is currently being referred to at a rate of approximately 150 surveys and associated reports per annum at processing plants in Australasia, South America and Africa. Examples throughout the paper provide insight into how the presented sample set of users have extracted benefits that could have otherwise not been safely or at all achieved.

Jan 1, 2009

By K Knorr

Desktop X-ray powder diffraction using a D2 PHASER equipped with fast linear detector was performed on several iron ore and mill scale samples. Data were analysed using cluster analysis and Rietveld quantitative phase analysis. The quantitative mineralogy of both materials could be established. Thus the input is provided for understanding the energy consumption and the CO2 emission during iron production. Furthermore, tabletop XRD allows to distinguish iron ore from mill scales and to quantify their mixtures.

Jul 11, 2011

Arm Royalty systems of different types are used throughout Australia by both state and federal governments to raise revenue and thus facilitate in the proper distribution of mineral wealth. Royalty systems should be neutral and equitable but by their very nature these objectives are impossible to obtain. Because of the individual nature of mineral deposits, in particular variable cutoff grades and tonnages, governments should be aware of the possible trade off between short and long term gains of the particular royalty scheme introduced.

Jan 1, 1982

By X Li, H Alehossein

The oscillating disc cutter (ODC) is an innovative technology for the continuous excavation of hard rock. This paper will discuss:the reasons for its development;its method of operation;current experimental results and mathematical modelling undertaken at the CMTE; andapplications in the mining and rock excavation industry.

Jan 1, 1999

As world demand for various minerals increases the mining industry in its endeavour to satisfy this demand will, eventually,look to the extraction of orebodies which previously may have been uneconomical to mine. These orebodies may be of two types. Firstly, new low grade orebodies and secondly, remnant sections of previously mined orebodies. Some of the factors relative to remnant mining operations are discussed and the potent- ial of remnant mining in providing an important contribution to future world metal production is considered.

Jan 1, 1975

Petroleum exploration is proceed ing in Western Australia at an ever- increasing pace. Results in recent years have been very successful, with the discovery and development of the Barrow Island oilfield and the Dongara gasfield, and the discovery of several major gas-condensate fields on the Northwest Shelf. The Northwest Shelf discoveries will have a big impact on the economy of the State by providing an abundant indigenous source of energy. Prospects for further large dis- coveries are believed to be excellent. The most prospective areas are thought to be on the continental shelf in the Carnarvon, Browse, Perth, Canning, and Bonaparte Gulf Basins.

Jan 1, 1973

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

The design, construction and operation of a 500,000 tonne per year Carbon-In-Pulp (C.I.P.) plant at Kambalda embracing the period from 1980 to 1982 has been previously discussed (Sceresini, 1982).Since that time the annual throughput rate has increased to 780,000 tpy.This paper discusses the changes and improve-ment made to allow this increased production to occur with minimal capital expenditure.

Jan 1, 1984

By Gadsden R. W

Physical and chemical requirements are defined for coke and ferrous materials used in modern high productivity blast furnaces operating in Australian conditions. Recent developments in the type of equipment required to be installed at the steelworks to ensure these requirements are described with illustrations from current plant practice provided.

Jan 1, 1976

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

By J E. Eberhardt

Ore sorting has long been used to raise the efficiency and thus lower the environmental impact of mineral processing operations. It was first instituted as hand sorting, according to a humanly perceived difference in the ore, but is now automated using large mechanical sorters in order to meet the high tonnage throughput required in most minerals processing applications. In the past, ore sorting was generally used as a niche processing route when other approaches failed, and in this context, consequential environmental benefits are often not the first consideration in adopting sorting. When applicable, ore sorting offers environmental benefits in reductions in fines waste, reagent usage and energy consumption in milling. Although there are significant opportunities for the use of ore sorting technology in many minerals processing operations, industry applications, to date, have been limited mainly to the processing of diamonds, magnesite, talc and uranium ores. This limitation has principally been due to a lack of suitable sensing technologies for a wide range of ore types. The authors report on a wide-ranging review of the automated sorting of mineral ores, and in particular, on methods for discrimination of ore characteristics prior to mechanical sorting.

Jan 1, 2002

By M Rankin, F Medina, R Verburg

We conducted a preliminary assessment of an extensive deposit of historic tailings discharged over a period of 40 years to the shoreline along a Southern Peruvian coastline. The tailings formed an extensive beach approximately 2.4 km long and 300 m wide. The tailings consist principally of pyrite (37 to 59 per cent), hematite (nine to 20 per cent), magnetite (three to 13 per cent) and quartz (11 to 36 per cent). The present operating company was required to evaluate the feasibility of capping the ocean side tailings deposit, however, given the size of the undertaking and the potential to reclaim residual minerals from the tailings, it was prudent to first evaluate whether capping would in fact reduce the impacts to the marine environment. Therefore this preliminary assessment examined: 1. metals contamination in tailings, shoreline porewater and marine sediments; 2. reactivity of tailings and acid generation potential; and 3. the potential for biological effects from metal contamination in the uplands tailings (solid phase) and beach porewater. Based on mineralogy, column leach studies and chemical results, the upland tailings have a high geochemical potential to acidify and release metals, especially copper, nickel and zinc, should they be subject to oxygenated and aqueous conditions. But, the extreme arid climate results in very low potential for precipitation and virtually precludes the transport of acid drainage reaction products from the upland tailings towards ocean. Wind erosion caused by offshore winds is likely a small source of tailing transport to the ocean. Since some potential exists to reprocess the tailings in the future, capping does not seem justified at present.

Jan 1, 2003

By J J. Cilliers, K Hadler, A W. Stra

This paper examines the use of the FrothSim flotation simulator to improve the performance of an industrial column flotation cell. The performance of an industrial retreat column cell is simulated, and, from the discrepancies between the simulated and experimental results, a problem with the wash water distribution is postulated. The scientific reason for the reduced performance with uneven wash water addition is described in detail. Further simulations indicated the potential for improvement with an even wash water distribution, resulting in both improved performance and reduced wash water usage. The simulated uneven wash water distribution was confirmed industrially, and the headers were redesigned and installed. A sampling campaign to compare the performance before and after the modifications showed that the flotation performance was improved dramatically, with a statistically significant decrease in gangue recovery, without a commensurate reduction in valuable mineral recovery.

Jan 1, 2005

The Kundana underground narrow vein gold mine had a recent history of large and damaging seismic events. Following a period of seismic events on 30 July 2001, in which nine miners were temporarily entrapped at depth due to falls of ground in several parts of the decline, the mine operation was required to develop a seismic management system to mitigate seismic risk to the operation. A micro seismic systems and boundary element modelling of mine sequence highlighted large-scale footwall faults and the mining of gold bearing shear veins to be focal structures for seismic energy release between depths of 300 m to the base of mining at 650 m. The integration of seismic data, identification of geological structures and mapping of zones of failed rockmass led to the successful generation of a non linear boundary element model and a seismic hazard strategy. This enabled mine sequences to be assessed daily, monthly and periodically for potential seismic hazards and therefore assigned both economic and personnel risks for the recovery of the ore reserve at the Kundana Underground Operation.

Jan 1, 2005

Relationships between lead blast furnace performance and the composition and size distribution of sinter were determined from analysis of lead blast furnace operating data. Sintering plant practice was subsequently modified and substantially improved furnace performance resulted.

Jan 1, 1971

The prime requirement is market, which for NZ inevitably means overseas markets. In order to be internationally competitive, the economies of scale and mechanical handling are essential. Since significant markets have not been sought, the full extent of our industrial mineral potential is not known. In general the technology exists to impart the desired quality, but at a price. Price is the main constraint, which may confine truly competitive operations to coastal situations to avoid high internal freight charges. Some commercial deposits of construction materials are being sterilised by zoning, making the costs to the consumer and country unnecessarily high. Unless management is enlightened and marketing is forceful, it can restrict growth. There is a good case to mount a search for phosphate minerals. The main growth areas are likely to be direct shipping ores like limestone, silica sand, and olivine, but in particular pumice.

Jan 1, 1978