Search Documents

By J Zhou, X Bi, Y Yan, W Peng, H Yang, D Weng, P Li

Fortescue Metals Group (FMG) fines from Western Australia is a hematite and limonite mix characterised by high crystal water content. Due to its higher supply capacity and lower prices, the Wuhan Iron and Steel Corporation (Group) intended to use more FMG fines in the sinter mix. It is understood that sinter quality is closely related to its microstructure featured by the hardness and brittleness of different mineral phases, the content of micro pores, and trans-cracks. In order to maintain sinter qualities such as tumble index, reducibility and so on at higher FMG fines blend ratios, a research project was initiated to study the effects of the FMG fines blending ratio on sinter microstructure. Research results showed that at higher FMG fines ratios, the hardness of hematite and magnetite were both decreased while the hardness of calcium ferrite showed a tendency to decrease. The number of cracks that were generated during Vickers hardness measurement in various mineral phases decreased, but their length was shortened, and the variation of crack lengths increased. The contents of hematite and magnetite were also reduced and the reduction of magnetite was clearer. Also the content of calcium ferrite and pores rose and the magnitude of the increase of pores was greater. Among all the mineral phases in sinter cakes, the Vickers hardness of hematite was highest within the range of 879 N/mm2 ~ 942 N/mm2, and therefore the decrease of its content in sinter and the enhancement of its brittleness, ie the number of cracks increased, were harmful to sinter strength. In addition, the excessive increase in pores content is also not favourable to sinter strength.CITATION:Bi, X, Yan, Y, Zhou, J, Peng, W, Li, P, Yang, H and Weng, D, 2013. Study of sinter microstructure with various blend ratios of Fortescue Metals Group fines, in Proceedings Iron Ore 2013 , pp 331-336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Rashchenko AF, Voiloshnikov GI, Elshin VV, Khomutov VV

The sorption method for the precious metals recovery fromsolutions and pulps are a perspective trend of modernhydrometallurgy. Russian gold mining industry uses thesemethods, anion-exchange resins being applied as sorbents. Theanion exchange resins allow effective recovery of preciousmetals, however, they have several drawbacks as compared withactivated carbons: high cost of sorbents; difficulties arisingduring treatment of pulps with complex ion composition;necessity of using titanic equipment and thiourea for gold elutionfrom loaded anion-exchange resin and its regeneration.

Jan 1, 1993

By Fyodorov A. N, Sorokin M. L, Komkov A. A

The Vanyukov Process is a bath smelting technology, that has been investigated for over 25 years and since 1977 has been in use on an industrial scale. Results of trials that have been carried out at the various pilot facilities over the past 15 years are considered in this paper. Both the main process aspects, design of the pilot furnaces and metal distributions are presented for consideration. Experience of the smelting of copper, copper-nickel, copper-zinc, nickel, lead, and pyrite concentrates is analysed.

Jan 1, 1992

By Stevens LG, Mok JK

With the long lead time requirement for engineering and construction of mineral pro- cessing facilities and the costly financing arrangements necessary, effective project management is essential to the successful and timely start up of these major production units. An added complexity is the frequently remote location of such projects and the demands this imposes on efficient project staffing, scheduling, logistics and cost control. Parsons recent experience with major projects such as Greenvale in Queensland and La Caridad in the desert of Northern Mexico and at remote locations like Sar Cheshmeh in Iran are described. The applications being developed for improving project controls through the use of computer techniques such as MSCS-COPES, and readily accessible and versatile transportation means are reviewed.

Jan 1, 1981

By Just G. D

Performance of draglines in large scale overburden stripping operations is critical to the efficiency of a major section of the Australian Coal Mining Industry. Optimisation of dragline productivity requires an understanding of a range of operating conditions and constraints. One of the least understood of these operations is the process of bucket filling and how this may vary with respect to variable operating conditions.Studies conducted at The University of Queensland over a number of years into this problem have enabled the mechanics of excavating to be assessed for different types of fragmented rock. In relation to bucket filling, factors such as fill volume, digging time and energy consumption have been found to be significant factors in optimising bucket design, bucket rigging and operational techniques.

Jan 1, 1992

By Quast K. B

Laboratory batch rod and ball milling tests were conducted on samples of Heavy Medium Separator (HMS) sinks from Renison Tin Limited. The product size distributions for this heterogeneous material were very different to similarly sized homogenous material previously reported by the authors. The effects of pulp density on product size distributions were only evident at pulp densities greater than 80 per cent solids. At high solids density, the major weight distribution product peak fell and broadened indicating less efficient breakage, particularly for rod milling. Tin distribution in the ground products was also affected by pUlp density, and there was always less cumulative per cent tin than cumulative per cent weight, ie there was no tendency for cassiterite to slime down to 10/lm.

Jan 1, 1995

By P Elliott, D Pershke

In a minerals processing context, sustainability is about using natural resources more efficiently to achieve maximum economic benefits with minimal environmental impacts. It embodies five overarching themes, which the paper will illustrate with practical examples from Australian minerals processing plants. These are:resource utilisation and materials efficiency,process waste reduction and enhancement of co-product values,reduction of water use and impacts,reduction of energy requirements and greenhouse gas emissions, andenhanced control of minor elements and toxic materials. Sustainability could be embedded profitably in minerals plant design in three dimensions: 1.technology,2.design, and3.operations. This presentation discusses a set of principles that could be applied to minerals processing technologies and provides an outline of sustainability assessment and opportunities evaluation tools. The application of the tools is illustrated through a case study by analysing a suite of nickel processing technology routes. The analysis reveals that current generation of nickel processing technologies do possess real potential to emerge as sustainability champions in integrated processing of nickel ores and concentrates, if they are designed, engineered, and operated for sustainability and adapted effectively to site specific constraints and opportunities. The paper will address data gaps and uncertainties regarding the impact of scaling up of pilot-plant performance, and provides strategies to overcome them.

Jan 1, 2006

The unique chemical and physical properties that can be displayed by polypropylene and its copolymer derivatives are enabling its development as a truly versatile material for water filtration. Well known applications include spiral wound cartridge filters commonly used for household water or the office drinking fountain, to pressure membranes that provide micro, ultra or nano size filtration barriers, whilst needle-felt or woven cloth filter belts or inline pressure bag cloths are well known to the hydro metallurgist and process engineer. A relatively new filtration concept that is generating interest and applications across all industries including the mining sector involves use of a unique fabric type filtering media made from polypropylene fibres. This technology not only has a vastly wider window for potential applications, it delivers an attractive cost saving alternative to the traditional sand media or diatomaceous earth type filters, along with potential benefits for integrated filtration units. This paper discusses the proven potential of the fabric media technology with examples of performance comparisons and confidence gained from full scale operating installations at mine sites and other locations.

Jan 1, 2004

By P Waters

BHP Billiton Iron Ore initiated a program in January 1995 at the Mt Whaleback operation in Newman, Western Australia to develop a closure plan for the overburden storage areas (OSA), which have the potential to generate acid rock drainage. The primary research program includes the development of technology for the long-term performance of OSAs with respect to slope stability, surface run-off, erosion, water infiltration and vegetation. The objective is to control acid rock drainage by preventing moisture movement into and through the OSA material. Infiltration to the underlying OSA material and closure costs are minimised due to the presence of the run-of-mine (ROM) cover material. A summary of the field data is presented to illustrate low percolation rates to the underlying OSA and key performance characteristics of the moisture store and release cover system design. Field data collected to date demonstrates that a moisture store and release cover system constructed with suitable ROM material has good potential as a final cover system at the Mt Whaleback site. The performance of the cover system on a sloped surface was significantly different as compared to placing the cover system on a horizontal surface.

Jan 1, 2003

By N G. Corner

A sea bed sampling programme by CRA Exploration Pty Limited over an area of 12 000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 106 m and contained a high grade core of 33 km2 which averaged 283 mg/m3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10 - 40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 h turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

By J F. C L Costa, J C. Koppe

The goal of this study is to characterise co-processed clinkers by identifying the most common minor elements, their distribution in the clinkers and possible effects on the mineralogical properties of the same. The results show the presence of an elevated content of transition metals, especially manganese concentrated in the matrix (up to three per cent) of the clinkers. Anomalous concentrations of arsenic have also been detected, especially at silicate crystal edges. The results indicate that the tracer elements can perfectly be associated to the mineralogical characteristics of the clinkers.

Jan 1, 2008

The state-owned Swedish company LKAB is one of the world's largest producers of iron ore. LKAB mines the greater part of its ore underground, and very high efficiency is vital if it is to compete successfully with open pit mines. Consequently, computers and OR are essential parts of the company's operations. This paper gives some examples of success- ful computer and OR applications at LKAB, coupled with some remarks on the costs and benefits of OR.

Jan 1, 1977

By Vilela A. C F

In the present work, the process of dephosphorisation of stainless steel was developed in laboratory scale by adopting a high frequence induction furnace, using BaCO3 base flux. By using BaCO3 - CaO - BaC12 - Fe2O3 Flux of about 110 g/Kg-metal, 30 per cent dephosphorisation degree was obtained a stainless steel containing 18,8 per cent Cr and carbon between 0,08 and 2,0 per cent. In addition, a dessulfurisation degree of 89 per cent was achieved too.

Jan 1, 1991

The St George orebodies are situated within the tectonically disrupted eastern limb of the Boogardie Syncline.Highly disturbed rafts of banded chert formations occur within a sequence of felsic volcanic tuffs. The chert forms the hostrock for the gold mineralization.The gold distribution within the irregular and narrow banded chert formations is erratic and patchy. The average gold content of the two orebodies is between 3 - 4 g/t Au.Economic mining of these relative small, irregular and low grade St. George orebodies can be carried out by using a highly selective mining method.The highly selective mining method uses an excavator as the principle mining tool. Blasting, breaking and loading of the rocks is done in a different way than by using a front-end loader as with the conventional mining method. Simple, and therefore cheaper, blasting breaks the rocks and lifts them up without major displacements.

Jan 1, 1984

By Mountiney B

The development and operation of three large open cut brown coal mines in the Latrobe Valley, Victoria, Australia, requires a wide range of drilling techniques for coal resource evaluation and stratigraphic defi- nition, material property identification, open cut dewatering, and instal- lation of groundwater monitoring bores. This paper describes in detail the range of drilling techniques, equip- ment used and associated problems with drilling, in a deep sedimentary basin containing several major brown coal seams, multiple aquifer sys- tems of varying pressures and thin layers of hard materials including pyrite, siderite and basalt. Methods of rotary drilling include wireline core drilling, conventional core drilling, conventional flush drilling, diamond core drilling, reverse circulation air lift drilling and bucket auger drilling. Cable tool drilling is also used for strata definition and aquifer sampling.

Jan 1, 1989

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

By Locke CA

Geophysical signatures of the Taranaki and Tongariro volcanoes reflect similarities in their age, composition and hydrothermal histories, but also reflect differences in host rock settings and edifice evolution. The Taranaki volcanoes have strong positive gravity anomalies showing that their edifices largely consist of dense andesite which reflects substantial lava production or dyke injection during construction and that large sub-edifice dykelstock complexes occur. In contrast, the Tongariro volcanoes have strong negative gravity anomalies indicating low density edifices of volcaniclastic material; no sub-edifice intrusions can be identified, probably because of the lack of density contrast with host basement rocks. Strong positive magnetic anomalies over the younger cones can mainly be attributed to near-surface andesite lavas or dykes whereas subdued magnetic effects are associated with hydrothermally altered zones within both edifices and sub-edifice intrusions.

Jan 1, 1995

By Tonegato S, Wood M

The lack of objective data on roof bolting machines, bits, rods and overall system has created the need for an objective assessment of roof bolting. This work outlines a test rig for such objective assessment of component parts of the roof bolting system.

Jan 1, 1986

By Fourney W. L, Dick R. D

A small-charge rapid excavation system employing a novel penetrating cone fracture initiation and propagation technique has been demonstrated to be capable of excavating the hardest of rocks at efficiencies (energy per unit volume of rock removed) four to ten times greater than attainable with conventional drill and blast. Significant enhancements to the concept developed during the research efforts include the use of propellant rather than explosive charges and a device for containing the charges and effectively sealing the shot-holes. The experimental results, including the excavation of several tons of hard rock in a research mine, have confirmed the novel breakage process and provided a data base for the design of a continuous hard rock mining machine based upon the concept. The small-charge excavation system would be attractive for civil construc-tion operations where sensitive structures, equipment and personnel would be in close proximity to the excavation face. The system would be attractive for selective mining operations where the ore rock could be fragment-ed and processed separately from the barren country rock. The barren rock could then be backfilled underground and eliminated from the traditional hauling and milling operations.

Jan 1, 1990

Optimisation and sensitivity analysis of final pit limits is now an accepted procedure for open pit planning studies. Tools to assist the design engineer in an underground metalliferous mine to make optimal choices for the selection of major development, stope geometry and cut-off grade analysis have not been available. The engineer has had to rely on experience and a limited analysis of design alternatives. A new tool called the `floating stope' has been developed to define the optimal (boundary) limit for material that can be economically extracted by underground stoping methods. The method is analogous to the `floating cone' method of open pit optimisation. The geology and mineralisation are modelled as a regular or subcell block model. Included in the model are structural and geotechnical features, and any previously mined out areas. Inputs to the procedure include the minimum stope dimensions, cut-off grade, stope head grade, and the way in which dilution is to be calculated. The optimisation procedure can be directed to maximise ore tonnes, grade, contained metal or the economic (dollar) value of material mined. The procedure can be applied at each stage of mine evaluation and design to assist with preliminary resource appraisal, selection of stoping methods, and detailed mine design. As with open pit optimisation procedures, manual intervention by an experienced engineer is required to produce practical and detailed designs. This practical design should follow the optimised design as closely as possible. The paper outlines the algorithms used in the definition of the stope envelope, and describes the analysis and results of several case studies where the optimisation procedure has been applied.

Jan 1, 1995