Search Documents

Railway cuttings require the highest care in design and construction, as the pro- bability of failure concept does not allow any risks to be taken with hundreds of lives being dependent on continued stability. The usual geological influences on stability such as bedding dip and faulting are often discus- sed, but other major problems may come from the presence of sheet joints, cross joints differential weathering and seasonal or daily changes of ground water level. The design of rail cuttings has taken little note of the problems imposed by cons- truction methods, and low cost quarrying methods may seriously weaken a designed shape. The presence of berms and drainage ditches is often difficult to achieve as blasting imposes cumulative stresses and jointing on rocks. Contractors face difficulties in bidding extensive rock cuttings as variations in rock properties are often concealed and overshoot- ing the toe of a batter can easily occur. Modern blasting methods offer some solutions, but the best guide to safe successful cuttings is extensive investigation and the continued involvement of engineering geology at the stages of feasibility, design, construction and maintenance. Two case histories show the influence of folding, faulting and construction methods in the case of slope failure and slope stability.

Jan 1, 1979

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

By Quilliam B, Richmond G

Aberfoyle Ltd. has utilised a variety of flotation technologies in the Hellyer concentrator in North-Western Tasmania. Hellyer ore, with its slow flotation rates and low rate differentials between values and gangue, requires the use of long residence times and low air consumption rates in the flotation circuit. The operation of the flotation circuit, with a nominal residence time of 7 hours, has necessitated the development of a control system to provide continuity through operator shift changes. Cell selections at Hellyer varied from the 54 m3 hybrid Dorf Oliver / Maxwell (DO/MX) cells, to smaller 32 m3 Maxwell cells, conventional Don-Oliver 300 (8.5 m3) and 600 (17 m3) trough cells, and a column cell. The advantages of the large cells included low specific power consumptions and a low capital cost. However, problems with mixing and the maintenance of consistent froth depth have been identified in the hybrid DO/MX cells. Short circuiting in the trough cells was apparent, causing a considerable reduction in metallurgical performance. The column cell performs to expectation, although the application is not ideal.

Jan 1, 1991

By G J. Butler

Since 2005 BHP Billiton Iron Ore has been working with the consulting company Runge to implement the software XPAC Advanced Destination Scheduler (ADS) in life-of-mine studies. The Mt Whaleback mine, being the single biggest open cut iron ore mine in the world, presents some special challenges in scheduling. The biggest challenge has been the slow run time and difficulty in targeting all ore and waste requirements. The high waste to ore strip ratio means that much of the cost of mining is tied up in waste dumping. It is therefore very important to schedule waste efficiently. At Mt Whaleback there is an additional challenge of managing two types of waste: inert and environmentally sensitive pyritic material. This paper shows how the XPAC destination scheduler is configured to achieve efficient and repeatable waste scheduling results at the Mt Whaleback mine. It also discusses proposed improvements to the process. The overall ore and waste schedule is configured to target mining parameters, crusher feed and grades. The schedule is run in two stages. The first stage is ore mining. The waste that needs to be mined is locked in a sequence. The second stage is the waste scheduling. The waste destination scheduler uses three inputs: source waste parcels locked in a sequence, a haul road and a waste dump block model. The process involves setting some rules for dump progression and haul path selection. These can be validated. The schedule is then run to target the shortest travel time. The results of scheduling are graphical and numeric and can be transferred into many different formats for reporting. The graphical result shows face positions in time that can be used for detailed dump design. The numeric results are used to estimate truck fleet size, fuel consumption, labour and equipment financials. The process has been successful in reducing the project time line, increasing the ability to do more scenarios and increasing schedule accuracy, transferability and repeatability.

Jan 1, 2007

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

Potential hlghwaJl mining reserves in Australia are large, but geotechnical and operating conditions are quite different from those where highwall mining has evolved in the USA. In order to achieve safe and effective resource recovery, equipment and procedures should be developed to penetrate 250 m in the Australian mining environment. This paper identifies key auributes to be incorporated in such machinery and methodology. These suggestions are intended to promote discussion on innovations to satisfy Australian requirements for highly productive, safe and environmentally acceptable techniques.

Jan 1, 1993

In todayÆs demanding business landscape continual change and technological advancement is a given. With these changes there is now, more than ever, a need to ensure sustainable growth in respect of value protection and value adding whilst meeting the pressures and expectations of the societies in which we operate. Traditionally the management of safety has been a very reactive activity in the business, in some cases seen as an irritation and a disruptive process that demands a focus on preventing reoccurrences. This in turn has focused the measurement of safety performance on a range of lagging indicators û æafter the effect managementÆ. Gaining and maintaining a licence to operate is crucial to a sustainable business but as a prerequisite, organisations need to have a demonstrable ability to manage the safety of their people, as well as mitigating the people risk associated with the business activity. A major focus in the last decade has been on the implementation of enterprise risk management programs, where risk becomes embedded in all business systems and processes and the organisationsÆ genetic make up is programmed to analyse and integrate risk management into all facets of the business activity. The management of safety should be no different. One school of thought argues that there are no new accidents, but rather our inability to learn from the past. Others believe that as long as we have an appetite to achieve the unachievable, we will have to continue to push the boundaries, our safety comfort zones and inevitably take risks. Single reliance on highly evolved technical systems, elaborate processes, highly skilled people, safe equipment and safe work environments have shown one thing û they are not sustainable in providing adequate coverage in the business. In analysing a range of factors associated with some of the worst catastrophes of the 20th century, it can be suggested that they were in fact predictable and inevitable and that an integrated approach underpinned by sound risk management systems could have determined a different result. The key to a sustainable approach in the management of safety requires us to look at a multitude of aspects that collectively allow the performance of an organisation to be predictable. To have certainty in the business activities it is necessary to have controls in place that will mitigate the risks normally associated with unwanted events. It is ensuring that human factors effectively contribute to monitoring the planned approach and being able to safely adjust to any variability. In essence this is having the ability to proactively plan for the longer term. The sentiments articulated by organisational leaders echo that safety management is good business. Surely then a good business is a sustainable business, and a sustainable business is one that provides lasting benefits to its stakeholders.

Jan 1, 2006

By P Gnnther, A M. van Niekerk

Coal mining operations in the Upper Olifants River Catchment in the Mpumalanga Province of South Africa are challenged with the increasing production of excess mine water that cannot be fully managed by existing practices of pollution control at source, recycling, and reuse on mining sites, storage and limited release to the natural water course. In contrast to this, the Olifants River Catchment is experiencing water stress and insufficient water is available to satisfy all water quantity and quality requirements for future industrial and municipal growth. It is estimated that the catchment has a deficit of 192 million m3 per annum if the reserve water requirements are taken into account. The future increased water requirements can be met by water transferred to the Olifants River Catchment from adjacent catchments. The cost of transferred water is likely to be substantially higher than the current cost of water supplied to local municipalities, commerce and industry. BHP Billiton and Anglo Coal Corporation are working together to jointly implement water management strategies that will contribute to the achievement of in-stream and dam water quality and aquatic objectives for the catchment. Consideration is now being given to the treatment and beneficial use of excess mine water. This will inaugurate a new era for the coal mining industry in South Africa, in which a pollution threat to the water resources in the Upper Olifants River Catchment is converted into a water source for beneficial use. Three potential mine water reclamation and reuse schemes have been identified and this paper details the technical, institutional, legal and financial considerations in the implementation of these schemes.

Jan 1, 2006

By Dharmappa HB, Sivakumar M

This paper is concerned with two case histories of wastewater quality management in underground coal mines in the Illawarra region. The first investigation briefly presents an analysis of mine water discharge having an extremely high concentration of suspended solids and consistently high barium concentrations, averaging, 14.4 mg/I Barium, over the sampling period. A laboratory study of chemical precipitation processes has indicated that about 91% of barium could be removed by using ferric sulphate and lime. On the basis of the information obtained from the environmental audit process an alternative water treatment and reuse system incorporating 51% reduction in the water consumption with 32% less off-site discharge has been suggested (Thomas, 1995).The second case history is concerned with the storm water management at a mine situated in the Illawarra escarpment where only 20% of the wastewater generated in the colliery is discharged off-site. Computer modelling of the storm water system showed that 75% of the clean runoff becomes contaminated through poor management practices and causes the process wastewater treatment system to fail in wet weather. Suggested improvements include relatively simple alteration to the coal wash filtration dams which are expected to reduce the periods of inefficient operation of these dams by 95%. The use of storm water diversion channels and detention basins can reduce the overflow volumes by 70 - 100 % for a ten year ARI (Average Recurrence Interval) storm event (Wingrove 1996).

Jan 1, 1998

By Gray E, Banks J

In mine site revegetation, exotic grasses are more commonly used than native grasses. This is due to unavailability of native grass seed on a commerical scale and lack of information on agronomical aspects of native grasses. This paper lists a number of native grass species that have the potential to grow well on mine sites, and provides some information on their seed collection, processing and germination. Further, it demonstrates via results of a field trial conducted at Ranger Mine spoil the relative performance of ten native grasses and Rhodes grass. It is concluded that (i) some native grasses have similar ability to grow on mine spoils compared to Rhodes grass and (ii) the use of native grasses have added advantages in ecosystem restoration.

Jan 1, 1994

By Albano C, Antila A, Flykt B

A method for relating operating variables and dewatering parameters of Thunes disc filters in the LKAB pelletizing plant at Malmberget in Sweden, via empirical mathematical models is described. Near orthogonal experimental design was used, where all independentvariables were allowed to span over their domain of variation and pseudo-randomly distributed among the experiments. The dewatering parameters are dependent on many variables and instead of using a traditional mechanistic model, an empirical model based on multivariate data analysis was chosen. The way of expressing the relation is by regression coefficients obtained from partial least square regression (PLS). Two empirical models were generated. The models were validated using an extra set of 56 experiments. The dewatering parameters were related to the design variables with few experiments, and user-friendly response surface methodology was used to determine the optimal conditions.

Jan 1, 1989

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

This paper presents an overview of the strategy adopted to bring the Ballymoney opencut lignite deposit to an advanced stage of mine design and confidence. Certain aspects of the project differentiate it from the normal Australian experience. These include the thick overlying glacial drift, the proximity to established infrastructure and the wide fluctua- tions in annual lignite demand. The incorporation of these factors in the mine plan are discussed. The deposit area is located near the town of Ballymoney, in Northern Ireland. In July 1986, after winning an internationally competitive tender, Meekatharra Minerals Ltd commenced an exploration programme designed to delineate reserves to supply a 450 MW power station. In less than eighteen months, a complete evaluation was undertaken and a price submitted in December 1987 to the relevant authorities for the supply of lignite. Subsequently, UK government consultants and significant inter- national banks have endorsed the findings. The mining study commenced with the evaluation of various develop- ment strategies, followed by selection of the most viable mining method and equipment. The equipment selected will mine four million tonnes of lignite and eleven million cubic metres of waste each year. In year 15, the waste removal requirement increases to almost seventeen million cubic metres. This results in an average strip ratio over the mine life of three cubic metres of waste per tonne of lignite. The quality of the product delivered to the run of mine conveyor transfer point, based on maximum resource recovery, will include heat content of 8813 kJ/kg (3789 Btu/Ib), ash content of 28% and moisture content of 40%.

Jan 1, 1989

The introduction of large diameter drill holes and mass firings in underground metalliferous mines has led to an increase in the number of reported sulfide dust explosions in Australia and overseas. Adaptation of the coal mining technique of using limestone to inhibit or prevent dust explosions has not been entirely successful as the development and inhibition of a sulfide dust explosion is somewhat different from that of a coal dust explosion. Tests were carried out on two pyritic ore samples, sulfur contents of 41 and 36 per cent, in 8 and 20 litre explosion chambers to evaluate the effect of the addition of limestone on the maximum explosive pressures developed and rates of pressure rise. Significant values were obtained in both chambers with dusts containing 60 per cent ore and 40 per cent limestone. The percentages of limestone required to inhibit the pyritic dusts were considerably higher than those values generally accepted by the mining industry and the current methods used to inhibit sulfide dust explosions should be re-evaluated.

Jan 1, 1986

The effects of process variables such as solution chemistry, flocculent type and dosage, intensity and duration of mixing, and solids type and concentration, on the performance of flocculation/clarification/thickening processes are described. System response is evaluated in terms of the specific effects on floc settling, supernatant clarity and sediment compressibility. The implications of these results with respect to industrial practice are discussed and general guidelines for direct application to plant design and operation are suggested.

Jan 1, 1993

Economic conditions dictated the lead time from concept to commissioning of the Kambalda C.I.P. Plant. The high gold price prevailing at the time the Victory ore-body was discovered provided the impetus to establish a treatment plant with the utmost haste. Consequently only limited metallurgical testing was possible. Fortunately the Kambalda Metallurgical Department had experienced gold metallurgists among its' staff. This enabled a rapid assessment to be made of the ore types to be treated. Flexibility was the keynote in the plant design. Overseas practice and experience was drawn upon extensively, but it was known that problems uniquE to the Kambalda Plant would be encountered due to the high nickel content of the C.I.P. Plant feed and the difficult clays in some of the areas. These fears were well founded and problems have been experienced. However the plant design has enabled these problems to be absorbed, if not overcome, and design production rates were achieved and maintained within three month; of start-up.

Jan 1, 1982

By Hendrix J. L, Nelson J. H

A study was conducted to examine how pretreatment of carbon-bearing gold ores with chlorine enhances gold recovery by cyanidation. It is hypothesized that metal species (including iron and copper) dissolved during chlorination adsorb on the carbon surface hindering the adsorption of dissolved gold. To test the hypothesis, samples of several sulfide minerals were subjected to reaction with sparged chlorine gas to determine which, if any, dissolve faster than gold under these conditions. Then, a synthetic carbonaceous refractory gold ore containing pyrite, chalcocite, activated carbon, and gold was subjected to gas sparging. The results of these experiments showed that chalcocite and arsenopyrite dissolve so that metal (copper and iron) is put into solution slightly faster than gold under the same chlorination conditions. Also, it was observed from the experiments that gold adsorbs on activated carbon during chlorination, but is replaced by copper and iron as the chlorination process dissolves more of the chalcocite and pyrite. The study concluded by investigating ferric chloride addition prior to chlorination to hinder gold adsorption on activated carbon.

Jan 1, 1991

By D Suppel, Y Miezitis, S Jaireth

The competition between various options for the use of land is ever increasing. Commonly in Australia large tracts of land were un-encumbered by sweeping land use option limitations, but this situation has been rapidly altering in recent decades as governments are obliged to maximise the utility of the land for a broad range of competing interests. While the interests of miners have always been considered, the effects on limiting access to land for exploration and possible mining have not always been effectively incorporated into decision-making processes. As a result the challenge for national and state organisations representing these interests has been to develop a transparent process to allow for the mineral potential of an area to be systematically assessed and for information to be presented for use by specialists and non-specialists. Government agencies are called upon to implement government policy but also to provide accurate and meaningful advice which can assist in policy and land use decisions. Commonly timeframes are short and information can be less than complete. Nevertheless on-going decisions are made based upon the best available understanding. It is in this operational framework that the methods described in this paper are set. The paper describes a process for quickly and systematically providing advice on mineral potential for use by government agencies and ultimately the community within tight time and resource constraints. It is a method of combining the accumulated knowledge about mineral resources and their potential and presenting this information in an easily accessible form which can be used in a negotiation and policy development environment. Development of the method was undertaken to meet the needs of the Regional Forestry Agreement process in Australia. The method has been applied to study areas in New South Wales, Tasmania, Western Australia and elsewhere. Examples in this paper are taken from north eastern New South Wales.

Jan 1, 1999

By S Pontual

Compact and field portable infrared spectrometers have been increasingly used over the past few years by an exploration industry constantly searching for a technological edge and the ability to more accurately and rapidly assess project areas. In particular, this technology allows large amounts of data to be rapidly collected on-site and sample mineralogy, mineral crystallinity and mineral composition to be quickly assessed. In recent years, short wave infrared (SWIR) reflectance spectroscopy has proved useful in a wide range of geological environments and at various stages of exploration programs, from grass roots reconnaissance through drilling programs and resource evaluation. Unfortunately these data have frequently been analysed and interpreted in isolation using time consuming data analysis techniques removed from the realities of a fast moving exploration industry. This paper presents new analysis techniques which allow these data to be efficiently integrated in the exploration program. Although SWIR data contain a wealth of mineral information it is impractical to use this information in its raw form. A more effective approach involves the extraction of key characteristics of these data (ie mineralogy, mineral composition and crystallinity) as numerical values, and the integration of this ædigital mineralogyÆ with more conventional exploration datasets (eg geochemistry, coordinate data, etc). This paper demonstrates that the integrated analysis of sound geological observations, geochemical, spatial and spectral data can quickly lead to a greater understanding of the nature and distribution of target mineralisation. As a first step, software driven pattern matching routines enable the identification of the major clay mineral species in a series of samples (eg kaolinite, montmorillonite and sericite). This allows the major alteration facies and their spatial distribution to be identified. Quantification of diagnostic absorption feature characteristics then allows more accurate determinations of mineralogy to be made (eg mineral composition and crystallinity). Examples of the application of SWIR analysis for alteration mapping from selected porphyry and epithermal systems from around the Pacific Rim are discussed. The data presented are derived from a variety of locations and sample types including drill core, ridge and spur rock chip samples, soil samples and geochemical pulps. In these large alteration systems, the spectral data can be used to describe and map the distribution of various alteration facies as many of these are characterised by clay and phyllosilicate mineral assemblages and are detected by SWIR analysis (eg smectite, chlorite, biotite, illite, muscovite, kaolinite, dickite, pyrophyllite, alunite, etc). In addition, the ability to evaluate even subtle trends in mineral crystallinity and composition is often vital in these systems when looking for vectors towards higher temperature parts of the system. In addition to detailed evaluation of mineralogy, the integration of digital mineralogy data with geochemical data leads to the ability to describe not only geochemically anomalous intersections or regions but also to recognise associations between subtle changes in mineralogy and target mineralisation. This is often important because understanding these mineralogical associations can lead to more accurate targeting and rapid assessment of the project.

Jan 1, 1999

Copper heap leaching involves both the simultaneous and sequential leaching of very large tonnages of ore over long periods of time. It is not unusual to be leaching three or four million tonnes over periods of 12 to 18 months. As a consequenc

Jan 1, 1998