Search Documents

By W Zhu, J H. Zhao, H Ma

The permeability coefficient is an essential parameter for the study of seepage flow in fractured rock mass. This paper discusses the feasibility and application value of using readily available RQD (rock quality index) data to estimate mine water inflow and grouting quantity. Firstly, the influence of different fracture frequencies on permeability in a unit area was explored by combining numerical simulation and experiment, and the relationship between fracture frequencies and pressure and flow velocity at the monitoring point in fractured rock mass was obtained. Then, the stochastic function generation program was used to establish the flow analysis model in fractured rock mass to explore the relationship between flow velocity, pressure and analyse the universal law between fracture frequency and permeability. The concepts of fracture width and connectivity are introduced to modify the permeability calculation formula and grouting formula. Finally, based on the on-site grouting water control case study, the rock mass quality index is used to estimate the mine water inflow and the grouting quantity. The results show that it is feasible to estimate the fracture frequency and then calculate the permeability coefficient by RQD. The relationship between fracture frequency and RQD and the relationship between structure surface frequency and permeability follow an exponential function. The calculation results are in good agreement with the field monitoring results, which verifies the rationality of the calculation method. The relationship between the rock mass RQD index and the rock mass permeability established in this paper can be used to invert the mechanical parameters of the rock mass or to evaluate the permeability and safety of the rock mass, which is of great significance to the prediction of mine water inflow and the safety evaluation of water inrush disaster management.

Nov 29, 2022

By S J. Henderson

Over much of Australia, rainfall is highly seasonal and storm-driven. Consequently, operational mines often need extensive earthworks – drains, dams and levees – for protection during the occasional large floods and for water storage against the dry times; however, it has not been appreciated that many of these earthworks will need to function after mining has finished, sometimes, beyond a normal design life for engineered structures.While a mine is operating, standards for design and maintenance are dictated by regulation and risk assessment. For dams and levees – regulated structures – the standards imposed mainly relate to life-of-mine. The levels of risk and maintenance accepted by the mine operator may not be acceptable to another landholder in perpetuity. However, the Environmental Authority cannot be surrendered unless the landholder has accepted responsibility for any unrehabilitated regulated structures (Department of Environment and Heritage Protection (DEHP), 2016).In order for a future landholder to be willing to take responsibility for a dam or levee, the structure should be of value to the business of the property. In addition, its management needs must be consistent with that business; for example, it should be maintainable using skills, equipment and materials normally available to the business.CITATION:Henderson, S J, 2016. Earthworks or landforms? Designing for lease surrender, in Proceedings Life-of-Mine 2016 Conference , pp 151–153 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

This paper describes operational experience with seam gas and spontaneous combustion management, gained during ten years of production history (1993 to 2003) in the Wynn seam at Dartbrook Coal mine. In addition, comparisons are made with more recent operational experience in the overlying Kayuga seam. Development and retreat longwall operations were undertaken in a 4.0 m thick working section of the Wynn seam, contained within the lower quarter of a circa 24 m thick mega seam, from 1993 until mining operations were relocated to the overlying Kayuga seam in 2004. Production from the first block of the Kayuga seam is currently underway with seam gas and spontaneous combustion management requirements being refined as further operational experience is gained. Seam gas management techniques, including pre-drainage with pressurised fracturing, surface to underground goaf drainage of a carbon dioxide rich seam gas and novel, high capacity ventilation circuits, were employed in the Wynn seam. Ventilation strategies included operating up to carbon dioxide STEL concentrations of 3.0 per cent in segregated return airways rather than being limited to the TWA-TLV concentration of 1.25 per cent. The spontaneous combustion experience at Dartbrook Coal has, to some degree, resulted in a change in the way the risk is managed in Australian coal mines. Values of carbon monoxide make and hydrogen concentrations are profoundly different from previously recommended management plan trigger levels and those used elsewhere in the industry. However, the detection of higher hydrocarbons together with rising oxygen depletion ratios and absolute hydrogen concentrations remain as indicators of advancing spontaneous combustion events. In this respect, experience gained in the Wynn seam was important in the initial management of the shallower Kayuga seam, an essentially greenfield site with no prior operational experience being available.

Jan 1, 2005

By Quast K. B

Samples of limestone and micaceous hematite have been ground in a laboratory batch mill using equal weights of either rods or balls. Values of the Schuhmann distribution modulus, a, have been shown to depend on grind time and do not remain constant as often reported. The linear reduction in a with grind time was attributed to a change in grinding mechanisms with time. The product sizing from ball milling limestone showed a bimodal distribution, but rod milling produced a unimodal size distribution. The product sizing from milling micaceous hematite was difficult to interpret due to the major influence of the shape factor on the transition from screen sizing to cyclosizing.

Jan 1, 1995

By H Plewes, A Bur, L Murray, J Pottie

Water recovery from tailings for reuse in mineral processing is essential to operation of mines in the Atacama Desert of Chile. With annual rainfall of 5 mm, the prudent and efficient use of available water resources is a major issue for the Escondida Mine and other mines in the area. The Escondida Mine is located at an altitude of 3100 m, in a very arid, seismically active part of the Atacama Desert of northern Chile. The site is located about 170 km from the coastal city of Antofagasta. From 1994 to 2002, tailings were discharged into the Hamburgo Tailings Facility, which comprises a series of æpaddiesÆ located near the open pit and mill. Because water in the region is only obtainable from groundwater sources, the paddy system incorporated a number of design features with the aim to maximise water recovery from the tailings. As part of the recent mill expansion to 237 500 metric tonnes per day, a new tailings facility, the Laguna Seca Tailings Facility, projected to be one of the largest tailings facilities in the world, was commissioned in 2002. Extensive studies were conducted for the design of the new facility to predict water recovery from the conventional wet disposal of tailings. The predictions were calibrated against the performance of the Hamburgo Tailings Facility and subsequently re-calibrated against actual performance during the first year of operation at the Laguna Seca Tailings Facility. Initial operation of the Laguna Seca Facility was marked by a coincidental change in tailings characteristics from design, which highlighted the need for thoroughly understanding tailings behaviour during deposition, and the parameters and deposition techniques that could enhance water recovery. Systems have been put in place to manage the tailings deposition and respond to changes in key parameters such that water recovery targets can be reliably achieved. This paper describes the background studies that were conducted to evaluate evaporation and tailings behaviour, summarises the water balance and then presents some observations from the commissioning and start-up of the facility.

Jan 1, 2003

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976

By Freeman NV

The concept of an in stream analysis probe was developed at The Zinc Corporation (now Z.C. Mines) in the late 1960's and commercialised quite rapidly, by Phillips and then AMDEL, as an alternative to the established centralised systems (Courier, etc.). The developments which have taken place since that time are reviewed and current procedures and performance are described. An audit of the system, recently undertaken by AMDEL, has highlighted areas where improvements can be made. In 1988 the ISA system will become an integral part of a substantially upgraded process control system.

Jan 1, 1988

Separating Particles by Horizontal Deflection in a Paramagnetic Fluid This paper describes the horizontal deflection behavior of particles in paramagnetic fluids under a high-gradient superconducting magnetic field. Movements of single particle were observed experimentally and indicated that they could be deflected to different positions. Based on these results, the behavior of groups of particles from ore samples was examined in the superconducting magnetic. It was found that these particles could be deflected and settled at a certain position due to the combination of gravity and magneto-Archimedes forces as well as a lateral buoyancy (displacement) force. Mineral particles with different susceptibilities and/or densities could be deflected to different positions, thus producing groupings of similar types of particles. The work described here, although in its infancy, could form the basis of new approach to separating particles based on a combination of susceptibility and density.  

Sep 13, 2010

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

The Taupo Volcanic Zone in New Zealand and the Philippine Mobile Belt in the Philippines are characterized by active subduction, active volcanism and high seismicity. The main factors affecting characteristics of geothermal systems in both countries are: tectonic setting, source magmas, maturity of the systems, and depth to the degassing magma body. Within New Zealand, geothermal systems are grouped into arc- and rift-type. Fluids in arc-type systems contain high amounts of volatiles (40%) and higher Cl contents (3,000-10,000 mg/kg). Maximum temperatures are also higher, reaching up to >400¦C. Arc-type alteration assemblages in New Zealand and the Philippines are similar. Because Philippine geothermal systems are less mature, have higher temperatures and steeper geochemical gradients than New Zealand ones, advanced argillization is more widespread occurring down to depths of 2000 m. Mineral phases are more varied due to the active input of magmatic waters and the formation of vapor conditions at depth, forming P04-, B-, Li-, Ce-, F-, and Cl-bearing minerals at high temperatures. In the Philippines, high temperature magmatic-hydrothermal to contact metamorphic assemblages containing biotite, amphiboles and pyroxenes are relatively common, but rare in New Zealand.

Jan 1, 1995

By K J ROSENGREN

Underground rock mechanics was initiated as a formal discipline in Australia by early studies for underground structures for the Snowy Mountains Scheme in the 1950s. These techniques were quickly embraced by underground mining and there has been steady development to the present time. The paper reviews the status of current techniques for rock mechanics studies and discusses some important issues such as ground support, mine filling and caving. It concludes that a considerable degree of engineering judgement is still required for the practical application of rock mechanics to underground mine design.

Jan 1, 1992

Cobar Mines Pty. Limited (CMPL) uses sodium sulphite as the principal depressant to attain selectivity in copper flotation prior to sequential recovery of lead and zinc. The usage of sodium sulphite is examined both from a theorectical viewpoint ana from the manner in which the copper circuit at (MPL has developed. The results of relatively recent investigations, both in the laboratory ana the plant, are discussed aria shown to support the present operating Techniques.

Jan 1, 1983

The Big Bend and Cobra molybdenum prospects which occur near the margin of the Karamea Batholith in the Northwest Nelson molybdenum province are compared. The Big Bend Prospect is a 3000 m by 800 m area of disseminated pyrite and anomalous molybdenum associated with Cretaceous porphyry intrusives and later argillic and potassic alteration within Ordovician schists and phyllites adjacent to the batholith margin. The Cobra Prospect is a 1200 m by 1200 m area of weakly disseminated pyrite mineralisation and anomalous molybdenum-in-rock associated with moderate to strong quartz-molybdenite and quartz-orthoclase-molybdenite veining in quartzite.

Jan 1, 1979

Safety and health at work is about people. It is about people who plan for work, organise work and perform work. It is about those who come in contact with the workplace and those who are responsible for the workplace. There are wider ranging safety and health obligations that are imposed on the industry stakeholders that span all phases of the production process. In all cases, those responsible for discharging the obligations must ask the questions: Is what we propose safe?, can it be done safer? and are we sure? What we learn from recent legal cases before the courts is that it is essential that all stakeholders work together in a collaborative way when discharging these obligations. Safety and health at work cannot become an issue that is viewed only through the eyes of a single stakeholder group. The reason for this is quite simple. The interrelatedness of the responsibilities that are imposed on each of the stakeholder groups, means that the performance based legislation simply wont work, where an active model of communication and consultation is not in place.

Jan 1, 2005

By Duniam P

Sequencing of large underground firings is a critical aspect of blast performance. Using theory developed in open cut operations, where blast results are easier to quantify, a new technique for sequencing underground mass blasts has been developed. The basis for the technique is to identify timing regimes to control fragmentation and relief then apply non-electrics to fit these criteria. The use of computer software to graphically interpret delay statistics enables the evaluation of designs in a realistic manner.

Jan 1, 1995

By N Collins, A Woodley, A N. Danoucaras, C McCombe, N C. Kunz

Over the past decade, the mining industry has come to recognise the importance of water both to itself and to others. Water accounting is a formalisation of this importance that quantifies and communicates how water is used by individual sites and the industry as a whole. While there are a number of different accounting frameworks that could be used within the industry, the Minerals Council of AustraliaÆs (MCA) water accounting framework (WAF) is an industry-led approach that provides a consistent representation of mine site water interactions regardless of their operational, social or environmental context that allows for valid comparisons between sites and companies.The WAF contains definitions of off-site water sources and destinations and on-site water use, a methodology for applying the definitions, and a set of metrics to measure site performance. The WAF is comprised of two models: the input-output model, which represents the interactions between sites and their surrounding community, and the operational model, which represents on-site water interactions.Members of the MCA have recently adopted the WAFÆs input-output model to report on their external water interactions in their Australian operations, with some adopting it on a global basis. To support this adoption, there is a need for companies to better understand how to implement the WAF in their own operations. Developing a water account is non-trivial, particularly for sites unfamiliar with the WAF or for sites with the need to represent unusual features. This work describes how to build a water account for a given site using the input-output model, with an emphasis on how to represent challenging situations.CITATION:Woodley, A, Danoucaras, A N, McCombe, C, Kunz, N C and Collins, N, 2013. A robust methodological approach for mine site water accounting, in Proceedings Water in Mining 2013 , pp 335-342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D Cohen, A Wurster

Many Southern African mining operations produce mine water which is beneficially and productively utilised on the mine sites and to support other water uses. Mine water treatment typically takes place within the context of integrated mine water management involving pollution prevention, waste minimisation, recycling and reuse as well as river discharges. Development of new and improved mine water treatment has focused on the neutralisation of metals removal, desalination of high sulfate waters and passive treatment. Mine water neutralisation processes now incorporate a combination of natural limestone and lime treatment, as well as features to maximise gypsum precipitation. The South African CSIR developed a suite of limestone-based neutralisation processes, which include reuse of CO2 and CaCO3 generated in the process. Desalination of high sulfate mine water is typically done using one of the following technologies:biological sulfate removal with different approaches to the handling of the sulfide generated in the process, and ultrafiltration (UF)/reverse osmosis (RO) treatment with different approaches to the handling and disposal of the brine. The current research and development focus is the separation and recovery of saleable products from the treatment residues and brine streams.

Jan 1, 2006

This paper outlines the thermodynamic and mass balance principles which affect the distribution of cobalt between matte and slag during the pyrometallurgical treatment of nickel - copper sulphides and considers the implications with regard to maximising the recovery of cobalt from the smelting and converting circuit.

Jan 1, 1992

By Yinxiang W, Chunlai Y

In older to improve efficiency of surface pre--grouting in sealing off water in heavily water-bearing strata, such as sandstone,siltstone and limestone, several methods have been used in China, they are ; intermittent pre-grouting, adjusting pre-grouting parameters and stepwise repeated pre-grouting methods. The paper describes effect of deviation on water sealing in pre-grouting. Deviation correction measures, like mechanical, technological and changing hole position methods have been introduced with satisfactory results in practical engineering projects without increasing the volume of engineering project and without causing delay.

Jan 1, 1988