Search Documents

By S Mitra, T Singh, D O’Dea, T Honeyands

Permeability and air flow rate in the bed during iron ore sintering is crucial to controlling the sinter quality and productivity of a sinter plant due to its influence on the flame front speed. In the present work, the permeability of the bed during sintering was analysed by means of measured pressure drop and temperature at multiple points in the bed during sintering. Three different zones were categorised, ie humidified (green) bed, region of maximum resistance (high temperature zone) based on temperature, and sintered bed. Previous work has shown that the maximum pressure drop during sintering was due to several concurrent physico-chemical processes including dehumidification, calcination of fluxes, dehydroxylation of goethite, combustion of coke and melting of granules (>1200°C). To quantify the effect of the different process, sintering experiments were conducted in a milli-pot (diameter 53 mm, height 400 mm) with pressure and temperature measured at same location in bed. The milli-pot was fitted with four equidistant (80 mm apart) taps. Overall, five sections in the milli-pot were analysed for pressure drop at different times during sintering. It was found that in region of maximum resistance, coke combustion and flux calcination were highest contributors with ~35 per cent of the pressure drop when compared to other processes like de-humidification and goethite dehydroxylation which contributed to ~20 per cent and 25 per cent each respectively. The pressure drop contribution of the coke combustion region increased with increasing coke addition rate.

Nov 8, 2021

Bauxite Resources Limited is grade drilling in its Western Australian Darling Range tenements to firm up resource definition and to develop mine plans. The Darling Range bauxite is generally in shallow deposits with minimum overburden. In the northern tenements, the ore is characterised by a higher silica layer which may extend from 0.5 to 1.5 m below, which high grade bauxite is found to a depth of four to 7 m. When grade drilling samples are taken, every 0.5 m and the recovered sample is weighed, logged and bagged. To eliminate splitting errors, the whole sample over the short interval is pulverised. Twinning holes variations are observed when using various drill rigs. Diamond core has been shown to give close to 100 per cent recovery and grades have been verified by digging bulk samples. As such, diamond core is used as the reference. It is intended to include sonic drilling as an alternative to diamond cores. This presentation details and attempts to explain the reasons for the observed variations in the various drilling methods used by Bauxite Resources Limited. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Mar 1, 2010

By F Radke, P A. Tilyard

Determination of the mineralogical location (deportment) of minor and trace elements (including credit and penalty elements) in base metal concentrates can indicate whether further processing is likely to (a) reduce the levels of the penalty elements, and/or (b) direct selected elements into other plant products, thereby increasing current concentrate grade or increasing payment for credit elements. To determine the deportment of elements requires knowledge of the proportions of the minerals present and their individual element contents. In addition, knowledge of the liberation and locking is important, as this can affect any possible further processing. Mineral proportions can be determined by a variety of methods including chemical analysis, point-counting, area-counting, QEM*SEM, image analysis and mineral separation. In the case of a Broken Hill zinc concentrate, several of these methods were used and gave consistent results.

Jan 1, 1998

Sheaves are a critical safety component in a winding system and are expected to survive such extreme loading events as rope break. Sheave designs have often been developed and evolved empirically, consequently many existing sheaves are not necessarily subjected to the detailed analyses that are possible using todayÆs design tools. The design philosophy for sheaves is that the rope should be the weakest link in the system so that associated equipment can function safely for any load up to rope break. A number of failure mechanisms must be considered, but buckling is often prominent. During the course of investigating the feasibility of upgrading the hoisting capacity of a winding system, the capacity of all critical components was reviewed. The sheaves in the system were found to have insufficient spoke buckling capacity for the specified rope. A proposal to increase the spoke buckling capacity by connecting spokes together using a simple tie arrangement was evaluated and found ineffective. An alternative tie arrangement concept was developed and evaluated and shown to be adequate. This paper describes the finite element model, analysis approach and results for the original sheave and the two modifications. The contribution of the sheave rim to the total buckling capacity is evaluated. Some practical issues for spoke tie modifications are discussed.

Jan 1, 2005

By S Miller, R Smart, J Thomas

Single-addition and sequential net acid generation (NAG) experiments were carried out on natural and prepared samples with varying contents of organic matter and pyritic S. Results show that carbonaceous matter can produce significant quantities of organic acids during peroxide oxidation in the NAG test, which leads to overestimation of acid-forming capacity and misclassification of benign samples as potentially acid forming (PAF). Organic matter effects were most pronounced in samples with low S (less than 0.5 per cent) and total organic carbon (TOC) contents of greater than seven per cent. The single-addition NAG test will tend to overestimate acid potential in samples with little or no pyrite and high organic matter content, potentially leading to sample misclassification. High pyritic sulfur samples tend to show little difference in single-addition NAG acidities with increasing organic matter, and it appears that pyrite is preferentially oxidised by peroxide when present in significant concentrations (greater than one per cent pyritic S). In sequential NAG tests overestimation was greatest in samples with little or no pyrite, but highly carbonaceous (>20 per cent TOC) pyritic samples were affected in later stages as the pyrite was depleted. A modified NAG method is proposed to account for the relative proportions of pyrite derived acidity and organic acidity in a given NAG solution.

Jan 1, 2003

By Stephenson D. B, Burgess J, Burgess F. L, Marshall S. H

A new high intensity flotation process 'FASTFLOT' is explained and its theoretical advantages compared with other flotation systems are discussed. The results of initial FASTFLOT testing on the zinc roughing circuit at Pasminco Mining, Broken Hill South concentrator are presented and compared to recent plant data. The comparison suggests that on roughing duties, the FASTFLOT process yields superior concentrate grade while requiring less than one third the residence time of a conventional mechanical cell plant. Strategies for FASTFLOT deployment are also presented.

Jan 1, 1994

By A Roshal

It is anticipated that many future uranium mines in Australia will be using the in situ leaching mining process. It is fair to say that close to one third of uranium production will be generated by this method, whilst the other two thirds will fall on the uranium generated from hard rock mining and other mining methods, such as traditional open cut mining. For other types of deposits the in situ leaching mining method will remain the best technological, commercial and environmental alternative. It is important to identify and prevent all risks involved in uranium mining. The expertise in this subject is limited. Over the years there was only one mine using the in situ leaching process for uranium extraction in Australia. Computer simulation of propagation of leachate during and after the uranium in situ leaching is a crucial factor, not only for addressing the environmental concerns, but also for the most efficient recovery of the deposit. The decontamination can be modelled for a period of up to 100 years, with the acid neutralisation forecast for a period of up to 400 years. The results of the modelling are paramount for definition of the reserves, efficiency of the mining method and the environmental impact statement. The accuracy of the hydrogeological modelling and carefully selected environmental management program enables a mining company to quantify and minimise the impact of the mining activities on the regional aquifer and to prevent environmental disasters. In the study, the completed hydrogeological model allowed the client, the authorities and the community to make an informed decision about the environmental impact of the in situ leaching of uranium. In particular, the model proved that neither during the mining, nor during the neutralisation the toxic elements would interact with the local catchment area.

Jan 1, 2008

By D Johns, L Murray

This paper discusses pore pressures in the embankments of tailings dams by comparing real world data with common design assumptions. Assessment of pore pressures has implications on material behaviour interpretation from CPT investigations and, therefore, on the design. For example, the assumption of hydrostatic pressure is conservative for limit equilibrium stability analyses but may be un-conservative in assessing the potential for contractive behaviour and strength loss during shearing. This paper presents some real world data, the investigation methods to determine the pore pressures, and subsequent interpretation of CPT data and material parameters such as the state parameter. It also examines the design implications of assuming a hydrostatic pressure distribution, by comparing results from that assumption with those obtained using the real pore pressures.CITATION:Johns, D and Murray, L, 2018. Characterisation of pore pressure in tailings dams and the implications for design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 239–249 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The Kaltails Project is situated close to the city of Kalgoorlie-Boulder in Western Australia. Located on the south-eastern fringe of the Golden Mile, Kaltails has been in operation since June 1989. The tailings forming the reserve for Kaltails have been derived from 100 years of underground mining on the Golden Mile, but, some of the re.;erve has been retreated in the past. A map of the tailings reserves and treatment plant site is presented as Figure 1. The gold project is a joint venture between Poseidon 90 per cent and Gold Corporation (ten per cent) and is managed by Poseidon Gold Kaltails.

Jan 1, 1992

The Ernest Henry Mine is an open pit copper-gold mining operation located in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current concentrator throughput of approximately ten million tonnes per annum. The pit will cease mining towards the end of 2010. Extensive surface diamond drilling has confirmed an extension of the orebody to depths of 1000 m below surface. A prefeasibility study was commissioned in late 2006 to investigate underground mining options with the preferred mining method being an inclined sublevel cave. In February 2008 mining of a decline commenced in conjunction with a feasibility study to further investigate the project. Work from the prefeasibility study indicates that an underground crusher, conveyor and hoisting shaft could be utilised to crush and transport broken ore from the sublevel cave workings to the concentrator. The study suggests that a production rate of five million tonnes per annum could be achieved and sustained for up to ten years. Ventilation designs and requirements will form a large section of the feasibility study. This paper will detail investigations of preliminary ventilation network designs of the proposed sublevel cave. Work has been completed using both Ventsim and VumA ventilation simulation packages. Ventsim was used to provide preliminary estimations and suggest alternatives for: surface fan duties;airflow characteristics (direction, velocity, pressure and quantity); andventilation network design in key mine areas. With mining activities reaching depths in excess of 1000 m below surface an analysis of heat conditions should be conducted. The VumA software package was used to model the thermal properties of the ventilation system. This model will provide a basis for the preliminary decisions on refrigeration requirements for the mine.

Jan 1, 2008

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

THE following paragraphs represent an endeavour to describe, briefly the equipment used for the manufacture of sulphuric acid and superphosphates by the Corporation.SULPHURIC ACID PLANTS.Two separate units are in operation, No. I Plant working on sulphur dioxide generated from pyritic ore, No. 2 Plant working on sulphurous gases obtained from the Huntingdon-Heberlein desulphurizing process. The latter plant is unique in being the first installation for the successful use of these gases.

Jan 1, 1918

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

ALTHOUGH the mineral Stannite (Cu2S, FeS, SnS2 , also known as "bell 'metal" ore, tin pyrites, etc.) is found in various parts of the world, in only three iocalities has development proved it to exist in sufficient quantity to warrant the erection of treatment plants. Two of those mines are in New South Wales and one is an Tasmania. The writer will deal with the latter-the Conah mine, Zeehan, Tasmania, it being the most important and extensive occurrence so far worked. The Conah mine was first worked by a Tasmanian company for silver-Iead, and was fairly remunerative until the zone of secondary enrichment was passed through, when the lodes became too poor for further exploitation. During the time that the line was thus operated the stannite lode was discovered. It occurs in a graphitic slate, which, in common with the slates and spilites of the Zeehan field, is probably underlain by the stanniferous granite which outcrops two miles to the west. The Conah stannite lode is older than the galena lodes of the district, being faulted by one of the latter. Near the surface the lode was very rich.Shipments were sent out assaying 150 oz. of silver per ton, 20% copper, and 18% tin. An .apparently homogeneous sample of stannite, analyzed by the writer for the Tasmanian Geological survey, gave the following results:

Jan 1, 1915

By C X. Zhang, W K. Ru, S C. Hu

To study the creep properties and the energy evolution characteristics of the weakly cemented rock (WCR) in western China, the creep deformation damage law of weakly cemented mudstone (WCM) under graded loading and the energy evolution characteristics of each creep stage were analysed based on the triaxial graded loading creep test of WCR. The results showed that as the confining pressure increased, the creep failure strength of the WCM increased from 9.5 to 24.8 MPa, and the relative displacement of the mineral particles in the mudstone increased gradually, resulting in a reduction in the fracture angle from 79.7° to 58.3°. At the same stress level, the strain energy Ue, the total energy U, and the dissipation energy Ud all increased as the confining pressure increased, but the growth rates of U and Ud decreased gradually, while the growth rate of Ue remained high. At the end of the stable creep stage, Ue increased slowly with the confining pressure, while U and Ud increased rapidly with the confining pressure, and their growth rates were basically the same. At the end of the accelerated creep stage, the growth trends of these three energies were all positively correlated with the confining pressure, Ue was significantly lower than that at the end of the stable creep stage, and Ud and U were further increased. These results revealed the unique creep properties and energy evolution characteristics of the WCR, providing a theoretical basis for long-term stability control of roadways that are built with WCR.

Nov 29, 2022

By J Rostami, T Afshar, M Sharifzadeh

Accurate estimation of rock load and selection of types of ground reinforcement to match post-failure behaviour of rock mass are important issues to assure tunnel stability. This paper focuses on the main factors affecting rock load to evaluate the capabilities of the existing models for prediction of rock load. Rock mass properties, project features and excavation method, as well as ground conditions and stress condition were found to be the key factors affecting the magnitude of rock load. Field data from tunnels of about 37.5?km driven in several geological structures in non-squeezing ground was used in this study. An in depth statistical analysis was performed on data to find correlations between the input parameters and measured/observed rock load. A weighting system was proposed to obtain the proper contribution of each factor for estimation of rock load in tunnelling through various ground conditions. The new classification system offered predicted values for rock load that were in a good agreement with the actual field measurements. The high disturbance factor (D>0.4) was the prime factor which controlled the rock load. Rock mass quality was the second key factor influencing rock load, which could be estimated by GSI, GSIresidual , especially when combined with tunnel depth.CITATION:Afshar, T, Sharifzadeh, M and Rostami, J, 2014. Estimation of rock load for tunnels with different disturbance factors, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Piason

Newstan Mine commenced mining operations in 1887 and has since undertaken extensive mining within the Young Wallsend, Great Northern, Fassifern, Borehole and West Borehole coal seams using a range of mining methods including board and pillar mining and longwall mining.Newstan Mine is planning to extend the existing mine workings using longwall and miniwall mining methods to produce up to 4.5 Mt/a of run-of-mine (ROM) coal for at least 25 years. The planned extension in the Main East and South West sections will involve developing new longwall panels and related mains headings. The new area contains higher specific gas emissions (SGE) than previously experienced at Newstan Mine. To achieve the optimum ventilation requirements for the longwall operation in this new area, a new ventilation shaft was designed to be constructed using the blind boring method in the South West Headings section.This paper presents the shaft design parameters and selection criteria for the construction of the new ventilation shaft, including the construction phase and the holing process to connect the shaft to the underground workings. The paper also discusses future ventilation requirements for Newstan Mine.CITATION:Piason, D, 2015. South-west ventilation shaft project at Newstan Mine, in Proceedings The Australian Mine Ventilation Conference, pp 229–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The Emmaville district is located in the northern part of the New England region of New South Wales some 400 miles north of Sypney. Better known for its substantial production of tin and tungsten ores, the Emmaville district has also been the centre of a small and somewhat sporadic production of copper, arsenic, silver, lead and zinc. This production has come principally from three mines-Webb's Silver Mine, Webb's Consols and, to a lesser extent, Pye's Creek Silver Mine.The ores from these mixed sulphide deposits are texturally and mineralogically complex and the problems of beneficiation are rather formidable.GENERAL GEOLOGYThe main rock type of the Emmanville district is a dark, brown to blackish massive siltstone of Permian age which overlies acid volcanics possibly also of Permian age. In places the siltstone gives way to conglomerates and standstones with discontinuous lenses of calcareous sediments (David, 1887).The whole series is folded but because of the massive character of the more expansive siltstone, detailed structure is difficult to delineate.Toward the close of Permian time the area was intruded by a series of intermediate to acid plutonic and hypabyssal rocks. Mineralization within the region is ascribed to the more acid of these intrusives-granodiorite, granite, and quartz-felspar porphyry (Lawrence, 1957, 1960).No intrusive rocks outcrop in the immediate neighbourhood of Webb's Silver Mine though granite occurs two miles...

Jan 1, 1961

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994

By Y T. J Kwong

With the recent emphasis worldwide on environmental protection and sustainable development, finding an enriched mineral deposit no longer guarantees mining development. Only if the identified resource can be exploited in an environmentally-friendly manner is it possible that a mine may be developed. Designed primarily to aid with exploring for similar deposits of a particular type, traditional genetic ore deposit models tend to ignore the fact that all mineral deposits are characterised by type-specific environmental signatures. In fact, how an ore deposit can be mined, the commodities of interest extracted and the resultant mine wastes managed are all largely dictated by the geology and mineralogy as well as the environmental setting of the deposit. An environmental ore deposit model integrates such related information to identify the environmental challenges associated with mining an ore deposit of a particular type and facilitates the selection a suitable combination of methods to minimise environmental risks and impacts. Given that environmental management consumes a large portion of the budget for a modern mining project, making informed decisions at all stages of mining development can reduce the overall project cost. Through case examples, this paper demonstrates how environmental ore deposit models may be useful in mine permitting, active mining and in site decommissioning. It is only through an innovative and flexible approach that the mining industry can shed its tarnished image and gain the social license to mine.

Aug 22, 2011