Search Documents

By Seib W

In cut-and-break rock excavation use is made of the fact that breaking rock in tension towards a free face requires a specific energy of excavation which is small in comparison with that required for rock excavation using conventional tools operating by a process of indentation of the rock.The process of cut-and-break excavation comprises firstly a cutting step in which a groove is cut into the rock surface, followed by a breaking phase in which a tool is inserted into the cut in order to break the rock adjacent to the cut.

Jan 1, 1992

By A M. Wala, H W. Wu

A research project incorporating a number of mine site exercises to reduce the effects of fire incidents and possible consequent health and safety hazards has been undertaken focused on the application of mine fire simulation software packages for contaminate tracing and fire modelling in coal and metalliferous mines. This paper examines aspects of introduction of inert gases to underground workings to aid recovery of a mine following a fire. Broad conclusions from work undertaken at individual Australian coal mines are discussed as examples. The effort is built around the introduction of the fire simulation computer program æVentgraphÆ to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Case studies have been developed to examine usage of inertisation units and particularly application of the GAG jet engine unit. One example has focused on selection of the best surface portal location for placement of the GAG for most efficient suppression of a fire. A second has examined a situation with significant seam gas being emitted on the face. This has shown that under certain face dip angles stopping the mine surface fan to reduce dilution of GAG exhaust gases will cause reversal of face air and consequent mine explosion as gas laden air is drawn across a fire. A third examines inertisation and dilution issues in mains headings. mains headings present a complex ventilation network with often numerous parallel headings, hundreds of cut-throughs and a variety of ventilation control devices. In such a complex system (with additional interference from a fire), maintaining control of the movement of inert gas is more difficult than elsewhere in the mine. Some illustrations of this issue are given.

Jan 1, 2005

By Groves D. I

The Norseman-Wiluna Belt (Fig.1) is a richly mineralized (production 1900 tonnes Au), Archaean greenstone belt, up to 800km long and 200km wide, which forms the major part of the Eastern Goldfields Province within the Yilgam Block. The Belt evolved ca. 2700 Ma ago as an oblique-slip mobile belt between flanking portions of an older greenstone terrane. Volcano-sedimentary successions in the Belt represent two distinct tectono-stratigraphic associations. Sequences of metamorphosed caic-alkaline intermediate to silicic volcanic rocks interlayered with tholeiitic basalts probably represent the remains of a dissected Archaean volcanic arc (or arcs), and sequences composed dominantly of ultramafic to mafic lavas and intrusions, with minor interflow tuffaceous, sulphidic or cherty sediments are interpreted as remnants of the floor of an ensialic marginal basin (Barley and Groves, 1988). Ultramafic volcanism at Kambalda has been dated at 2692 ¦ 2 Ma (Claoue-Long et al., 1986). The dominantly volcanic associations are locally overlain by coarse clastic sedimentary succes- sions. The Belt is also typified by major north- to north-northwest-striking fault systems, shear zones, and tectonic lineaments, many of which are traceable for more than 300km. As well as defining the boundaries of the belt, these structures have accomodated much of the regional strain and acted as conduits for hydrothermal fluids during deformation, metamorphism and mineralization. As a result, most of the epigenetic gold deposits in the Belt occur in subsidiary structures related to these fault systems (Eisenlohr et al., 1988). Deformation involved oblique compression resulting in a closely spaced network of low-angle faults (thrusts) as well as upright folds and oblique- to strike-slip faults (Archibald, 1987; Veamcombe et al., 1988). This was accompanied by regional metamorphism and granitoid emplacement. At Kambalda, regional deformation and metamorphism were synchronous with the emplacement of the Kambalda Granodiorite which has been dated at 2662 ¦ 4 Ma (Hill and Compston, 1986), approximately 30 Ma after volcanism.The tectonic history and style of deformation of the Norseman-Wiluna Belt are similar to those of Phanerozoic oblique- slip mobile belts at continental margins, which are also a major source of hydrothermal gold mineralization.

Jan 1, 1988

By P K. Seccombe

The McKinnons gold deposit is hosted by weakly deformed, Palaeozoic metasedimentary rocks of the Cobar Basin in the western Lachlan Fold Belt of New South Wales. Mineralisation comprised a largely supergene resource of 1.7 Mt of ore, grading 1.7 g/t gold, established over structurally controlled, primary gold and base-metal mineralisation in underlying, carbonate-rich meta-siltstones and sandstones of Early Devonian age. Mineralisation was associated with at least two major fluid cycles. The first cycle was characterised by four stages of vein formation. Early quartz and carbonate veins (Stages 1 and 2) and quartz-pyrite breccias (Stage-3) occurred prior to, or early in, the main regional deformation (D1). Continued D1 deformation produced syntectonic, carbonate-base-metal veins (Stage-4), primarily in dilatant zones adjacent to fold axes. The second cycle of mineralisation was an epithermal-style event, driven by a shallow, syn-D2 or post-tectonic intrusion, defined by aeromagnetic imaging. The intrusion may have exploited a jog, controlled along the basin margin by basement faults. Mineralisation produced gold-pyrite veins, associated with pervasive quartz-sericite-adularia and chlorite-sericite alteration. Highest primary gold grades are confined to quartz-adularia boiling zones. The McKinnons deposit offers an important example of mineralisation formed by multiple processes. Early-stage, base-metal mineralisation at McKinnons reflects structurally focussed, basin dewatering and metamorphic processes, typical of other deposits in the Cobar Basin. By contrast, late-stage gold mineralisation at McKinnons is magmatically driven and of epithermal style. Recognition of overprinting distinctive geological events is critical, not only in modelling ore formation, but in developing a versatile exploration concept.

Jan 1, 1999

The geographical region of South East Asia is variously defined, but generally agreed to include the Asean group - Philippines, Malaysia, Thailand, Singapore and Indonesia. Other regional countries, such as Vietnam, Laos, Burma, Kampuchea etc. are of course geographically part of the region, however in economic terms, they play a minor role. It is the Asean group that dominates present economic activity and provides the overwhelming opportunity for commercial development. My experience in South East Asia has been gleaned over 15 years of regular travel in the region. More recently, we have established company offices in Malaysia, Singapore and Indonesia to extend and deepen contacts with major customers. This progressive development is an integral part of a planned growth pattern and will be discussed in more detail shortly. South East Asia is a rapidly developing economic growth centre, a fact which is clearly recognised and accepted by most commentators. An important question is then to be asked: Why has the region been relatively neglected by Australian, U.S. and European industrial supply companies? I will attempt to address this question in the context of industrial minerals and propose some ideas as to how effective sales programs could be developed. Firstly, let's consider the market potential provided by countries within the region. It is reasonable to suggest that industrial growth in S.E. Asia over the past 20 years has been generally steady and in some cases, explosive. Until recently, this growth has predominantly been driven by development of internal (regional) demand. Population growth and rising living standards have ensured that basic industries have enjoyed a solid uptrend in sales and production. The industries which most benefitted from regional economic development over this period were, interestingly, those which we understand to be major users of industrial minerals - glass, ceramics, paper, surface coatings, cement, refractories, rubber and plastics. Each of these industrial sectors has been influenced by different growth stimulii over a 20 year period. Nevertheless, they also enjoy a common feature which ensured an above average performance. All sectors are fundamental to an environment enjoying rising living standards and rapid growth in general prosperity. More recently, internal growth factors have been overtaken by a recognition that manufactured products from the region are competitive in export markets. This comparatively recent development provides the most interesting possibilities for higher value industrial mineral raw materials. Let me explain: For 20 years, industrial growth in South Asia has essentially been focused on satisfying domestic demand. Finished quality of manufactured items was orientated to a developing market more interested in cost than aesthetics or long life. This was reflected in raw material specifications, which often did not exist and at the best were undemanding.

Jan 1, 1989

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By W D. Ortlepp

Seismicity associated with deep block cave mining operations in hard rock can give rise to dynamic loading of the mining openings. A description is given of the source and damage mechanisms associated with such seismic events, and the possible demands placed on the rock support by the resulting dynamic loading. In addition, production level drifts are often subjected to large static deformations during mining. Appropriate support, able to sustain large static deformations, and capable of absorbing the energy released during dynamic loading, is described. The performance of these support types has been determined by means of large-scale dynamic loading tests, and large deformation static laboratory tests. Finally, a support system which is considered to be appropriate for extraction drifts in block cave layouts subjected to dynamic loading is described.

Jan 1, 2000

By Wetzeil N

High ambient temperatures combined with high surface humidity in the north of Australia and, in particular, the northern areas of the Northern Territory can make underground workplaces relatively inhospitable at certain times of the year. . Woodcutters' silver/lead/zinc mine, situated some 80 km south of Darwin, would be the most northerly underground operation of any significance in Australia. As such, during the build up to the wet season, it has a particular problem of ventilating a deep underground mine with already high dry and wet bulb temperatures at the surface. The Mine Management Act and Regulations mention only that workplaces shall be 'in a fit state for a person to work in or occupy'. Woodcutters therefore set in progress a Heat Stress Program to endeavour to set standards which would be more measurable and justifiable. The aim of the program was to compile a record of ambient atmospheric conditions in the working areas such that areas and/or work activities generating high ambient temperatures and humidities could be identified, quantified and qualified. Once the analysis stage of this program was completed, Woodcutters compiled a set of recommendations for the continued monitoring for, and control of, heat stress conditions to ensure that no underground employee was placed at risk from 'heat stress'. These recommendations are discussed in this paper.

Jan 1, 1994

By R A. Pax

Heavy machinery such as AG and SAG mills generate a significant amount of noise due to the processes that are occurring inside them. From an environmental perspective, the level of noise generated is a significant occupational safety hazard. However from a technical perspective the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of the primary comminution tumbling mills. Traditionally, the use of perfect mixing has been assumed when modelling the operation of AG/SAG mills. If this were true then the acoustic emissions from AG/SAG mills would be uniform along the length of the mill. Experimentally this has been found not to be the case. From another perspective it should not be the case because of the different conditions existing at the feed end compared to the discharge end. This paper presents the results determined by non-contact acoustics and their analysis in terms of understanding of the mechanisms occurring inside a mill.

Aug 8, 2011

The passage of a vast array of new State and Federal environmental legislation over the last couple of years has required many mine operators to sharpen their focus on environmental requirements. Established requirements, such as environmental impact assessment, minimising disturbance and rehabilitation must now be complemented by mine environmental management plans. These may not only require regular monitoring of mine operations and detailed forward planning to prevent or reduce environmental harm caused during mine operation, but annual updating. It is likely that in future these plans will be required to incorporate general principles such as pollution prevention, sustainable development, waste minimisation and conservation of biodiversity and ecological integrity.

Jan 1, 1993

In both exploration and mining, the laboratory is often seen as a cost rather than a profit centre. The aim in most mining companies is to increase profits by reducing costs, so the budget for the laboratory is under constant pressure.There is another option; to see the laboratory as the brain of the operation. By lifting the status of the laboratory and treating it as a profit centre, mine costs may be reduced in other ways, e.g. reduction in milling costs. This change of status will require investing more capital in better equipment, more training for employees and more employees to carry out project research.There are many examples of major costs being incurred because of inadequate laboratory work. Conversely, by spending more money on laboratories and their activities, overall costs can be reduced or profits enhanced.

Jan 1, 2002

By A E. McElnea, M A. Martens

An 18-month project was undertaken to test the effectiveness of controlled daily tidal exchange augmented with hydrated lime treatment of surface waters as an approach for remediating a severe acid sulfate soil disturbance at East Trinity, Cairns, north Queensland. Actual acid sulfate soils were producing hazardous levels of acid and heavy metal contaminants and degrading approximately 720 of the 940 ha East Trinity property and the adjacent foreshores. A government-led research team established a series of research projects with the aim of characterising the site (soils, water, terrain) and testing the effect of the lime-assisted tidal exchange management strategy on soils, water, sediments and biota.

Jan 1, 2003

By Borgelt B. V, Perry A. J, Wellington H. K

There has been little change in the lead smelting practice at Mount Isa since 1939 when the metallurgy and general practice were outline by Raney and Blott.The purpose of this paper is to descriqe some of the operational details that have influenced the overall production. The slag fall hns been increased by the lowering of the lead content of the concentrate. Further, as it is the practice to include iron on the furnace charge and carry a higher lime content in the slag, both factors have produced notable results in furnace operations.All blast furnace gases are filtered in a baghouse and this unit is. being further extended to take all smelter gases, thus eliminating the existing Cottrell plant handling Dwight-Lloyd gases.The lead smelter was closed down from April 1943, to May 1946, during which time blister copper was produced.The report is subdivided as follows:-1. Filtering and Mixinga. Effect of calcium sulphate on cloth.b. Dwight-Lloyd charge composition.c. Main mixer.d. Return sintel sizing.2. Blast Furnace Operationsa. Introduction.b. Use of orehearth.

Jan 1, 1953

By D MacKay

The Mt Wright Project is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. Underground Development of the current Mt Wright orebody commenced in June 2006 and the first production ore was brought to surface in June 2007. The orebody is a rhyolite pipe containing fine-grained disseminated gold in a granite host rock. Ground conditions tend to be good to excellent throughout development, with some minor deformation experienced when stope-sized excavations are formed. The mine commenced as a sublevel open stoping (SLOS) operation with the intent to utilise development waste to back fill isolated upper level stopes while developing to the bottom of the known orebody. The mine plan intended to commence production with a bottom-up primary/secondary stoping retreat through the main orebody utilising cemented fill. Some challenges were faced during the initial production phase that included:•Ongoing underground diamond drilling and updating of the block model resulted in some issues reconciling the grade control results to the resource model. This was primarily due to the high variability of grade which in turn caused difficulties in accurately identifying areas of low and high-grade.•The cost of establishing and operating a cemented fill plant to achieve the planned extraction sequence of the orebody had increased significantly beyond initial estimations.•Geotechnical conditions such as stress orientations, ground behavior and response to the forming of excavations learned through the mining of the upper level stopes were different to the assumptions made during the initial design.A number of in-house and external reviews of the mining method were completed which has resulted in a revised mining plan. This paper will summarise the challenges faced and the implementation of the mine plan to date.

Mar 21, 2011

Mechanical and electrical (M&E) systems in road tunnels are constrained by the traffic envelope and the construction profile. Whilst these spatial constraints are often ælocked inÆ early in the design process, the detailed M&E design continues for some considerable time after key civil engineering issues have been resolved. Ventilation design criteria for both normal and emergency operation often involves considerable negotiation with a wide range of stakeholders. Final system performance and spatial requirements are only finally resolved when suppliers are selected following the tender process. Lighting design is dependent upon a wide range of factors including tunnel lining materials and associated colours as well as agreed maintenance regimes. Cabling systems can only be developed when the general arrangement for power distribution is agreed and a system of substation, switchrooms and equipment rooms is in place. Many other systems such as fire protection and communications facilities fill the available space beyond the traffic envelope, where physical, structural and æsight lineÆ requirements must all be accommodated. The more co-ordinated civil engineering and M&E design is and the earlier the process starts the better the outcomes for all parties.

Jan 1, 1999

By Tack K

During its 28-year life the MHD ISP smelter has gone through two phases, each of about a dozen years. The first phase was a learning one; in the second phase the lessons were applied and throughput and production rose strongly. Early experience revealed the robustness and the flexibility of the Imperial Smelting Process. The experience was demonstrated by strong increases in the throughput of mixed lead-zinc concentrates and of secondary (oxide) zinc materials. Purchased material quantities rose from 175 000 tonnes/year to 200 000. The required capacity increase of the IS furnace to smelt the higher throughput was achieved by relatively minor modifications; for instance a change to the internal furnace profile gained an extra two square metres in cross sectional area. The furnace hearth area has remained practically unchanged over its entire history. The paper concludes that there is still more potential to be drawn from the process and MHD intends to sustain raw material input at a new level of 240 000 tonnes/year. However, this rate will have to be achieved under the imposition of more stringent environmental and product quality standards than ever before.

Jan 1, 1993

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

By G Neely

COPING WITH COMPLEXITY In every industry, and mining is no exception, plant and processes increase in complexity over time and managers and operators need correspondingly more knowledge. The mine manager has to delegate details to operators, engineers, metallurgists, accountants, safety specialists, personnel officers and the rest. Is it reasonable then, to expect the Mines Inspector to be competent to judge the conduct of all these operations against the criterion of the regulations? Obviously not, but what are the alternatives? One is a superficial inspection where the inspector goes on a hazard hunt for broken steps and missing handrails. Another is one in which an army of specialist inspectors marches on a mine, sometimes outnumbering the staff. Each is competent to assess some part of the operation and if he or she can find an opposite number among the mine staff, they can discuss details. But what good does it achieve? The system acts to remedy present defects and to make recommendations which, if only they were followed, would prevent the same things happening again. Given that this process has been going on since the first Factory Act of about 1840, how is it that there are any more defects left to put right? The answer of course is that defects keep appearing, and new defects arise as fast as the old ones are found and corrected. Further progress can only be made by preventing defects at their source.

Jan 1, 1994

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

Concrete has been used for many years in block caving, principally for drift and drawpoint linings. This paper describes the requirements for concrete in this application, the required properties, the mix design, and transportation and placement systems. In addition a concrete mix design rationale is also proposed.

Jan 1, 2000